In commit df06fd6782 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.
The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.
Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.
Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26ac ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad4 ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 05ca14fdb6.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the slcan driver to switch the
"err-rst-on-open" setting on and off.
"err-rst-on-open" on - Reset error states on opening command
"err-rst-on-open" off - Don't reset error states on opening command
(default)
The setting can only be changed if the interface is down:
ip link set dev can0 down
ethtool --set-priv-flags can0 err-rst-on-open {off|on}
ip link set dev can0 up
Link: https://lore.kernel.org/all/20220628163137.413025-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case the bitrate has been set via ip tool, this patch changes the
driver to send the open ("O\r") and close ("C\r) commands to the
adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It allows to set the bitrate via ip tool, as it happens for the other
CAN device drivers. It still remains possible to set the bitrate via
slcand or slcan_attach utilities. In case the ip tool is used, the
driver will send the serial command to the adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch for the upcoming support to change the
bitrate via ip tool, reset the adapter error states via the ethtool API
and, more generally, send commands to the adapter.
Since the close command (i. e. "C\r") will be sent in the ndo_stop()
where netif_running() returns false, a new flag bit (i. e. SLF_XCMD) for
serial transmission has to be added.
Link: https://lore.kernel.org/all/20220628163137.413025-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As suggested by commit [1], now the driver uses the functions and the
data structures provided by the CAN network device driver interface.
Currently the driver doesn't implement a way to set bitrate for SLCAN
based devices via ip tool, so you'll have to do this by slcand or
slcan_attach invocation through the -sX parameter:
- slcan_attach -f -s6 -o /dev/ttyACM0
- slcand -f -s8 -o /dev/ttyUSB0
where -s6 in will set adapter's bitrate to 500 Kbit/s and -s8 to
1Mbit/s.
See the table below for further CAN bitrates:
- s0 -> 10 Kbit/s
- s1 -> 20 Kbit/s
- s2 -> 50 Kbit/s
- s3 -> 100 Kbit/s
- s4 -> 125 Kbit/s
- s5 -> 250 Kbit/s
- s6 -> 500 Kbit/s
- s7 -> 800 Kbit/s
- s8 -> 1000 Kbit/s
In doing so, the struct can_priv::bittiming.bitrate of the driver is not
set and since the open_candev() checks that the bitrate has been set, it
must be a non-zero value, the bitrate is set to a fake value (-1U)
before it is called.
Using the rtnl_lock()/rtnl_unlock() functions has become a bit more
tricky as the register_candev() function indirectly calls rtnl_lock()
via register_netdev(). To avoid a deadlock it is therefore necessary to
call rtnl_unlock() before calling register_candev(). The same goes for
the unregister_candev() function.
[1] commit 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20220628163137.413025-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upcoming changes on slcan driver will require you to specify a bitrate
of value -1 to prevent the open_candev() from failing but at the same
time highlighting that it is a fake value. In this case the command
`ip --details -s -s link show' would print 4294967295 as the bitrate
value. The patch change this value in 0.
Link: https://lore.kernel.org/all/20220628163137.413025-5-dario.binacchi@amarulasolutions.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It is used successfully by most (if not all) CAN device drivers. It
allows to remove replicated code.
Link: https://lore.kernel.org/all/20220628163137.413025-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the typo "poniter" -> "pointer" in the kerneldoc of
ctucan_interrupt().
Link: https://lore.kernel.org/all/20220628083204.881311-1-mkl@pengutronix.de
Fixes: 2dcb8e8782 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.")
Cc: Ondrej Ille <ondrej.ille@gmail.com>
Cc: Martin Jerabek <martin.jerabek01@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is the can327 driver. It does a surprisingly good job at turning
ELM327 based OBD-II interfaces into cheap CAN interfaces for simple
homebrew projects.
Please see the included documentation for details and limitations:
Documentation/networking/device_drivers/can/can327.rst
Link: https://lore.kernel.org/all/20220618195031.10975-1-max@enpas.org
Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
[mkl: minor coding style improvements]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- Brought the copyright notice up to date
- Also regarding the changed company name from
esd electronic system design gmbh to esd electronics gmbh
- Using socketcan@esd.eu as a generic mail address for matthias who
left esd 6 years before
- Added a second MODULE_AUTHOR() for Frank Jungclaus
Link: https://lore.kernel.org/all/20220624190517.2299701-6-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Each occurrence of the term "usb2" within variables, function names,
comments, etc. is changed to "usb" where it is shared for all
esd CAN/USB devices.
Link: https://lore.kernel.org/all/20220624190517.2299701-4-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As suggested by Vincent, renaming of esd_usb2.c to esd_usb.c
and according to that, adaption of Kconfig and Makfile, too.
Link: https://lore.kernel.org/all/20220624190517.2299701-2-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
This patch is similar to 7e193a42c3 ("can: netlink: allow
configuring of fixed bit rates without need for do_set_bittiming
callback") but for data bit rates instead of bit rates.
Usually CAN devices support configurable data bit rates. The limits
are defined by struct can_priv::data_bittiming_const. Another way is
to implement the struct can_priv::do_set_data_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::data_bittiming_const or struct
can_priv::do_set_data_bittiming is implemented.
In commit 431af77925 ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::data_bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_data_bittiming
callback on devices with fixed data bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220613143633.4151884-1-mkl@pengutronix.de
Fixes: 431af77925 ("can: dev: add CAN interface API for fixed bitrates")
Acked-by: Max Staudt <max@enpas.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The field rx_max_packet_size of struct es58x_device in nothing else
than usb_endpoint_descriptor::wMaxPacketSize and can be easily
retrieved using usb_maxpacket(). Also, rx_max_packet_size being used a
single time, there is no merit to cache it locally.
Remove es58x_device::rx_max_packet_size and rely on usb_maxpacket()
instead.
Link: https://lore.kernel.org/all/20220611162037.1507-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Frames can be directly injected to a can driver via the packet
socket. By doing so, it is possible to reach the
net_device_ops::ndo_start_xmit function even if the driver is
configured in listen only mode.
Add a check in can_dropped_invalid_skb() to discard the skb if
CAN_CTRLMODE_LISTENONLY is set.
Link: https://lore.kernel.org/all/20220610143009.323579-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The functions can_dropped_invalid_skb() and can_skb_headroom_valid()
grew a lot over the years to a point which it does not make much sense
to have them defined as static inline in header files. Move those two
functions to the .c counterpart of skb.h.
can_skb_headroom_valid()'s only caller being
can_dropped_invalid_skb(), the declaration is removed from the
header. Only can_dropped_invalid_skb() gets its symbol exported.
While doing so, do a small cleanup: add brackets around the else block
in can_dropped_invalid_skb().
Link: https://lore.kernel.org/all/20220610143009.323579-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The devices are meant to be under the "Device Drivers" category of the
menuconfig. The CAN subsystem is currently one of the rare exception
with all of its devices under the "Networking support" category.
The CAN_DEV menuentry gets moved to fix this discrepancy. The CAN menu
is added just before MCTP in order to be consistent with the current
order under the "Networking support" menu.
A dependency on CAN is added to CAN_DEV so that the CAN devices only
show up if the CAN subsystem is enabled.
Link: https://lore.kernel.org/all/20220610143009.323579-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Only a few drivers rely on the CAN rx offload framework (as of the
writing of this patch, only four: flexcan, m_can, mcp251xfd and
ti_hecc). Split it out of can-dev and add a new config symbol:
CAN_RX_OFFLOAD.
The drivers relying on CAN rx offload are in different sub
folders. Make CAN_RX_OFFLOAD an hidden option and tag all the drivers
depending on that feature with "select CAN_RX_OFFLOAD" so that the
option gets automatically enabled if and only if one of those drivers
is chosen.
Link: https://lore.kernel.org/all/20220610143009.323579-5-mailhol.vincent@wanadoo.fr
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The canonical way to select or deselect an object during compilation
is to use this pattern in the relevant Makefile:
bar-$(CONFIG_FOO) := foo.o
bittiming.c instead uses some #ifdef CONFIG_CAN_CALC_BITTIMG.
Create a new file named calc_bittiming.c with all the functions which
are conditionally compiled with CONFIG_CAN_CALC_BITTIMG and modify the
Makefile according to above pattern.
Link: https://lore.kernel.org/all/20220610143009.323579-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the next patches, the software/virtual drivers (slcan, v(x)can)
will depend on drivers/net/can/dev/skb.o.
This patch changes the scope of the can-dev module to include the
above mentioned drivers.
To do so, we reuse the menu "CAN Device Drivers" and turn it into a
configmenu using the config symbol CAN_DEV (which we released in
previous patch). Also, add a description to this new CAN_DEV
menuconfig.
The symbol CAN_DEV now only triggers the build of skb.o. For this
reasons, all the macros from linux/module.h are deported from
drivers/net/can/dev/dev.c to drivers/net/can/dev/skb.c.
Finally, drivers/net/can/dev/Makefile is adjusted accordingly.
Link: https://lore.kernel.org/all/20220610143009.323579-3-mailhol.vincent@wanadoo.fr
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the next patches, the scope of the can-dev module will grow to
engloble the software/virtual drivers (slcan, v(x)can). To this
extent, release CAN_DEV by renaming it into CAN_NETLINK. The config
symbol CAN_DEV will be reused to cover this extended scope.
The rationale for the name CAN_NETLINK is that netlink is the
predominant feature added here.
The current description only mentions platform drivers despite the
fact that this symbol is also required by "normal" devices (e.g. USB
or PCI) which do not fall under the platform devices category. The
description is updated accordingly to fix this gap.
Link: https://lore.kernel.org/all/20220610143009.323579-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Usually CAN devices support configurable bit rates. The limits are
defined by struct can_priv::bittiming_const. Another way is to
implement the struct can_priv::do_set_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::bittiming_const or struct
can_priv::do_set_bittiming is implemented.
In commit 431af77925 ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_bittiming
callback on devices with fixed bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220611144248.3924903-1-mkl@pengutronix.de
Fixes: 431af77925 ("can: dev: add CAN interface API for fixed bitrates")
Reported-by: Max Staudt <max@enpas.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds Transmitter Delay Compensation (TDC) feature support.
In the case of higher measured loop delay with higher bit rates, bit
stuff errors are observed. Enabling the TDC feature in CAN-FD
controllers will compensate for the measured loop delay in the receive
path.
Link: https://lore.kernel.org/all/20220609103157.1425730-1-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
[mkl: fix indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel test robot noticed that the ctucanfd platform driver fails
during modpost on platforms that don't support IOMEM.
| ERROR: modpost: "devm_ioremap_resource" [drivers/net/can/ctucanfd/ctucanfd_platform.ko] undefined!
This patch adds the missing HAS_IOMEM dependency.
Link: https://lore.kernel.org/all/20220523123720.1656611-1-mkl@pengutronix.de
Fixes: e8f0c23a24 ("can: ctucanfd: CTU CAN FD open-source IP core - platform/SoC support.")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Ondrej Ille <ondrej.ille@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver does a lot of casting of smaller buffers to
struct kvaser_cmd_ext, GCC 12 does not like that:
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:489:65: warning: array subscript ‘struct kvaser_cmd_ext[0]’ is partly outside array bounds of ‘unsigned char[32]’ [-Warray-bounds]
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:489:23: note: in expansion of macro ‘le16_to_cpu’
| 489 | ret = le16_to_cpu(((struct kvaser_cmd_ext *)cmd)->len);
| | ^~~~~~~~~~~
Temporarily silence this warning (move it to W=1 builds).
Link: https://lore.kernel.org/all/20220520194659.2356903-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
clang emits a -Wunaligned-access warning on union
mcp251xfd_tx_ojb_load_buf.
The reason is that field hw_tx_obj (not declared as packed) is being
packed right after a 16 bits field inside a packed struct:
| union mcp251xfd_tx_obj_load_buf {
| struct __packed {
| struct mcp251xfd_buf_cmd cmd;
| /* ^ 16 bits fields */
| struct mcp251xfd_hw_tx_obj_raw hw_tx_obj;
| /* ^ not declared as packed */
| } nocrc;
| struct __packed {
| struct mcp251xfd_buf_cmd_crc cmd;
| struct mcp251xfd_hw_tx_obj_raw hw_tx_obj;
| __be16 crc;
| } crc;
| } ____cacheline_aligned;
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
This is a false positive because the field is always being accessed
with the relevant put_unaligned_*() function. Adding __packed to the
structure declaration silences the warning.
[1] https://github.com/llvm/llvm-project/issues/55520
Link: https://lore.kernel.org/all/20220518114357.55452-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 30f3b42147 ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work
now the code can be removed as preparation for a CAN netdevice Kconfig
rework.
Link: https://lore.kernel.org/all/20220518154527.29046-1-socketcan@hartkopp.net
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: remove led.h from MAINTAINERS]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to remove the weight argument from the basic version of the
netif_napi_add() call. Move all the callers in drivers/net/can that
pass a custom weight (i.e. not NAPI_POLL_WEIGHT or 64) to the
netif_napi_add_weight() API.
Link: https://lore.kernel.org/all/20220517002345.1812104-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
slcan does a manual check in slc_xmit() to verify if the skb is valid.
This check is incomplete, use instead can_dropped_invalid_skb().
Link: https://lore.kernel.org/all/20220514141650.1109542-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CTU CAN-FD IP core is only useful when used with one of the
corresponding PCI/PCIe or platform (FPGA, SoC) drivers, which depend on
PCI resp. OF.
Hence make the users select the core driver code, instead of letting
then depend on it. Keep the core code config option visible when
compile-testing, to maintain compile-coverage.
Link: https://lore.kernel.org/all/887b7440446b6244a20a503cc6e8dc9258846706.1652104941.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now when Intel Elkhart Lake uses again common bit timing and there are
no other users for custom bit timing, we can bring back the changes
done by the commit 0ddd83fbeb ("can: m_can: remove support for
custom bit timing").
This effectively reverts commit ea768b2ffe ("Revert "can: m_can:
remove support for custom bit timing"") while taking into account
commit ea22ba40de ("can: m_can: make custom bittiming fields const")
and commit 7d4a101c0b ("can: dev: add sanity check in
can_set_static_ctrlmode()").
Link: https://lore.kernel.org/all/20220512124144.536850-2-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 0e8ffdf3b8.
Commit 0e8ffdf3b8 ("can: m_can: pci: use custom bit timings for
Elkhart Lake") broke the test case using bitrate switching.
| ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
| ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
| candump can0 &
| cangen can1 -I 0x800 -L 64 -e -fb \
| -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v
Above commit does everything correctly according to the datasheet.
However datasheet wasn't correct.
I got confirmation from hardware engineers that the actual CAN
hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0.
Datasheet was mirroring values from an another specification which was
based on earlier M_CAN version leading to wrong bit timings.
Therefore revert the commit and switch back to common bit timings.
Fixes: ea4c178768 ("can: m_can: pci: use custom bit timings for Elkhart Lake")
Link: https://lore.kernel.org/all/20220512124144.536850-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Chee Hou Ong <chee.houx.ong@intel.com>
Reported-by: Aman Kumar <aman.kumar@intel.com>
Reported-by: Pallavi Kumari <kumari.pallavi@intel.com>
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warnings:
| drivers/net/can/ctucanfd/ctucanfd_platform.c:67:2-9:
| line 67 is redundant because platform_get_irq() already prints an error.
Link: https://lore.kernel.org/all/20220421203242.7335-1-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Pave Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Defining local versions of NAPI_POLL_WEIGHT with the same values in
the drivers just makes refactoring harder.
Link: https://lore.kernel.org/all/20220429174446.196655-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous split budget between TX and RX made it return not using
the entire budget but at the same time not having calling called
napi_complete. This sometimes led to the poll to not be called, and at
the same time having TX and RX interrupts disabled resulting in the
driver getting stuck.
Fixes: 6cec9b07fe ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the device of the device tree node should be rather than the
device of the struct net_device when allocating DMA buffers.
The driver got away with it on sparc32 until commit 53b7670e57
("sparc: factor the dma coherent mapping into helper") after which the
driver oopses.
Fixes: 6cec9b07fe ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-2-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
(Thread 1) | (Thread 2)
| grcan_reset_timer()
grcan_close() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | grcan_initiate_running_reset()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn
Fixes: 6cec9b07fe ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Cc: stable@vger.kernel.org
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MCP251863 device is a CAN-FD controller (MCP2518FD) with an
integrated transceiver (ATA6563). This patch add support for the new
device.
Link: https://lore.kernel.org/all/20220419072805.2840340-3-mkl@pengutronix.de
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the bit timing constants as const.
Fixes: c223da6893 ("can: xilinx_can: Add support for CANFD FD frames")
Link: https://lore.kernel.org/all/20220317203119.792552-1-mkl@pengutronix.de
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Link: https://lore.kernel.org/all/20220419081449.2574026-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Technologic Systems has rebranded as embeddedTS with the current
domain eventually going offline. Update web/doc URLs to correct
resource locations.
Link: https://lore.kernel.org/all/20220329201229.16279-1-kris@embeddedTS.com
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CiA (CAN in Automation) lists in their Newsletter 1/2018 in the
"Recommendation for the CAN FD bit-timing" [1] article several
recommendations, one of them is:
| Recommendation 3: Choose BRPA and BRPD as low as possible
[1] https://can-newsletter.org/uploads/media/raw/f6a36d1461371a2f86ef0011a513712c.pdf
With the current bit timing algorithm Srinivas Neeli noticed that on
the Xilinx Versal ACAP board the CAN data bit timing parameters are
not calculated optimally. For most bit rates, the bit rate
prescaler (BRP) is != 1, although it's possible to configure the
requested with a bit rate with a prescaler of 1:
| Data Bit timing parameters for xilinx_can_fd2i with 79.999999 MHz ref clock (cmd-line) using algo 'v4.8'
| nominal real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error
| 12000000 12 2 2 2 1 1 11428571 4.8% 75.0% 71.4% 4.8%
| 10000000 25 1 1 1 1 2 9999999 0.0% 75.0% 75.0% 0.0%
| 8000000 12 3 3 3 1 1 7999999 0.0% 75.0% 70.0% 6.7%
| 5000000 50 1 1 1 1 4 4999999 0.0% 75.0% 75.0% 0.0%
| 4000000 62 1 1 1 1 5 3999999 0.0% 75.0% 75.0% 0.0%
| 2000000 125 1 1 1 1 10 1999999 0.0% 75.0% 75.0% 0.0%
| 1000000 250 1 1 1 1 20 999999 0.0% 75.0% 75.0% 0.0%
The bit timing parameter calculation algorithm iterates effectively
from low to high BRP values. It selects a new best parameter set, if
the sample point error of the current parameter set is equal or less
to old best parameter set.
If the given hardware constraints (clock rate and bit timing parameter
constants) don't allow a sample point error of 0, the algorithm will
first find a valid bit timing parameter set with a low BRP, but then
will accept parameter sets with higher BRPs that have the same sample
point error.
This patch changes the algorithm to only accept a new parameter set,
if the resulting sample point error is lower. This leads to the
following data bit timing parameter for the Versal ACAP board:
| Data Bit timing parameters for xilinx_can_fd2i with 79.999999 MHz ref clock (cmd-line) using algo 'can-next'
| nominal real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error
| 12000000 12 2 2 2 1 1 11428571 4.8% 75.0% 71.4% 4.8%
| 10000000 12 2 3 2 1 1 9999999 0.0% 75.0% 75.0% 0.0%
| 8000000 12 3 3 3 1 1 7999999 0.0% 75.0% 70.0% 6.7%
| 5000000 12 5 6 4 1 1 4999999 0.0% 75.0% 75.0% 0.0%
| 4000000 12 7 7 5 1 1 3999999 0.0% 75.0% 75.0% 0.0%
| 2000000 12 14 15 10 1 1 1999999 0.0% 75.0% 75.0% 0.0%
| 1000000 25 14 15 10 1 2 999999 0.0% 75.0% 75.0% 0.0%
Note: Due to HW constraints a data bit rate of 1 MBit/s with BRP = 1 is not possible.
Link: https://lore.kernel.org/all/20220318144913.873614-1-mkl@pengutronix.de
Link: https://lore.kernel.org/all/20220113203004.jf2rqj2pirhgx72i@pengutronix.de
Cc: Srinivas Neeli <sneeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the function can_rx_offload_queue_sorted() to
can_rx_offload_queue_timestamp(). This better describes what the
function does, it adds a newly RX'ed skb to the sorted queue by its
timestamp.
Link: https://lore.kernel.org/all/20220417194327.2699059-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this warning.
Found pipes are now saved to struct mcba_priv and code uses them
directly instead of making pipes in place.
Fail log:
| usb 5-1: BOGUS urb xfer, pipe 3 != type 1
| WARNING: CPU: 1 PID: 49 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| Modules linked in:
| CPU: 1 PID: 49 Comm: kworker/1:2 Not tainted 5.17.0-rc6-syzkaller-00184-g38f80f42147f #0
| Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
| Workqueue: usb_hub_wq hub_event
| RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| ...
| Call Trace:
| <TASK>
| mcba_usb_start drivers/net/can/usb/mcba_usb.c:662 [inline]
| mcba_usb_probe+0x8a3/0xc50 drivers/net/can/usb/mcba_usb.c:858
| usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
| call_driver_probe drivers/base/dd.c:517 [inline]
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220313100903.10868-1-paskripkin@gmail.com
Reported-and-tested-by: syzbot+3bc1dce0cc0052d60fde@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220311080208.45047-1-hbh25y@gmail.com
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220311080614.45229-1-hbh25y@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
beacause can_put_echo_skb() deletes the original skb and
can_free_echo_skb() deletes the cloned skb.
Link: https://lore.kernel.org/all/20220228083639.38183-1-hbh25y@gmail.com
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Cc: stable@vger.kernel.org
Cc: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_put_echo_skb() will clone skb then free the skb. Move the
can_put_echo_skb() for the m_can version 3.0.x directly before the
start of the xmit in hardware, similar to the 3.1.x branch.
Fixes: 80646733f1 ("can: m_can: update to support CAN FD features")
Link: https://lore.kernel.org/all/20220317081305.739554-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Reported-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Clang static analysis reports this issue:
| mcp251xfd-core.c:1813:7: warning: The left operand
| of '&' is a garbage value
| FIELD_GET(MCP251XFD_REG_DEVID_ID_MASK, dev_id),
| ^ ~~~~~~
dev_id is set in a successful call to mcp251xfd_register_get_dev_id().
Though the status of calls made by mcp251xfd_register_get_dev_id() are
checked and handled, their status' are not returned. So return err.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/all/20220319153128.2164120-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Link: https://lore.kernel.org/all/20220314115354.144023-28-Julia.Lawall@inria.fr
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds TX IRQ coalescing support to the driver.
The implemented algorithm is similar to the RX IRQ coalescing support
added in the previous patch.
Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds RX IRQ coalescing support to the driver.
The mcp251xfd chip doesn't support proper hardware based coalescing,
so this patch tries to implemented it in software. The RX-FIFO offers
a "FIFO not empty" interrupt, which is used if no coalescing is
active.
With activated RX IRQ coalescing the "FIFO not empty" interrupt is
disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full
interrupt" (depending on RX max coalesced frames IRQ) is used instead.
To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce
usecs IRQ,on timer expiration the "FIFO not empty" is enabled again.
Support for ethtool configuration is added in the next patch.
Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
So far the configuration of the hardware FIFOs is hard coded and
depend only on the selected CAN mode (CAN-2.0 or CAN-FD).
This patch updates the macros describing the ring, FIFO and RAM layout
to prepare for the next patches that add support for runtime
configurable ring parameters via ethtool.
Link: https://lore.kernel.org/20220313083640.501791-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch prepares the driver for runtime configurable RX and TX ring
parameters. The actual runtime config support will be added in the
next patch.
Link: https://lore.kernel.org/20220313083640.501791-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a helper function to calculate the ring configuration
of the controller based on various constraints, like available RAM,
size of RX and TX objects, CAN-mode, number of FIFOs and FIFO depth.
Link: https://lore.kernel.org/20220313083640.501791-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of an erroneous ring configuration more RAM than available
might be used. Change the printf modifier to a signed int to properly
print this erroneous value.
Fixes: 83daa863f1 ("can: mcp251xfd: ring: update FIFO setup debug info")
Link: https://lore.kernel.org/20220313083640.501791-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the freeing of the "oskb", by using kfree_skb()
instead of kfree().
Fixes: 1574481bb3 ("vxcan: remove sk reference in peer skb")
Link: https://lore.kernel.org/all/20220311123741.382618-1-mkl@pengutronix.de
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for ABE CAN Debugger devices using the gs_usb driver.
Link: https://lore.kernel.org/all/20220309124132.291861-22-mkl@pengutronix.de
Signed-off-by: Ben Evans <benny.j.evans92@gmail.com>
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For example CANext FD needs to distinguish between bittiming constants
valid for arbitration phase and data phase to reach maximum
performance at higher speeds.
Link: https://lore.kernel.org/all/20220309124132.291861-20-mkl@pengutronix.de
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Christoph Möhring <cmoehring@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CANtact Pro from LinkLayer Labs is based on the LPC54616 µC, which
is affected by the NXP LPC USB transfer erratum. However, the current
firmware (version 2) doesn't set the
GS_CAN_FEATURE_REQ_USB_QUIRK_LPC546XX bit.
This patch sets the feature GS_CAN_FEATURE_REQ_USB_QUIRK_LPC546XX to
workaround this issue.
For the GS_USB_BREQ_DATA_BITTIMING USB control message the CANtact Pro
firmware uses a request value, which is already used by the
candleLight firmware for a different purpose
(GS_USB_BREQ_GET_USER_ID).
This patch set the feature GS_CAN_FEATURE_QUIRK_BREQ_CANTACT_PRO to
workaround this issue.
Link: https://lore.kernel.org/all/20220309124132.291861-19-mkl@pengutronix.de
Cc: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Christoph Möhring <cmoehring@christ-es.de>
[mkl: improve check for CANtact Pro and add GS_CAN_FEATURE_QUIRK_BREQ_CANTACT_PRO quirk]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For the GS_USB_BREQ_DATA_BITTIMING USB control message the CANtact Pro
firmware uses a request value, which is already used by the
candleLight firmware for a different
purpose (GS_USB_BREQ_GET_USER_ID).
This patch adds a quirk to use the CANtact Pro's value for the
GS_USB_BREQ_DATA_BITTIMING USB control message instead of the official
one.
Link: https://lore.kernel.org/all/20220309124132.291861-18-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce a workaround for a NXP chip errata on LPC546xx
controllers (Errata sheet LPC546xx / USB.15).
According to the document corruption can occur when the following
conditions are met:
* A TX (IN) transfer happens after a RX (OUT) transfer.
* The RX (OUT) transfer length is 4 + N * 16 (N >= 0) bytes.
Even though the struct gs_host_frame has a size of 76 bytes for a FD
frame, which does not apply to the above rule, corruption could be
seen.
Adding a dummy byte to break the second condition also on transfer
lengths with 4 + N * 8 bytes reliably circumvents USB transfer data
corruption.
The firmware can now request this quirk by setting
GS_CAN_FEATURE_REQ_USB_QUIRK_LPC546XX.
Link: https://lore.kernel.org/all/20220309124132.291861-17-mkl@pengutronix.de
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Christoph Möhring <cmoehring@christ-es.de>
Signed-off-by: Alexander Schartner <aschartner@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANtact Pro from Linklayer is the first gs_usb compatible device
supporting CAN-FD with a different HW and re-written candlelight FW.
Support for CAN-FD is indicated by the device setting the
GS_CAN_FEATURE_FD flag. CAN-FD support is requested by the driver with
the GS_CAN_MODE_FD flag. The CAN-FD specific data bit timing
parameters are set with the GS_USB_BREQ_DATA_BITTIMING control
message.
This patch is based on the Eric Evenchick's gs_usb_fd driver (which
itself is a fork of gs_usb). The gs_usb_fd code base was reintegrated
into the gs_usb driver, and reworked to not break the existing
classical-CAN only hardware.
Link: https://lore.kernel.org/all/20220309124132.291861-16-mkl@pengutronix.de
Link: https://github.com/linklayer/gs_usb_fd/issues/2
Co-developed-by: Eric Evenchick <eric@evenchick.com>
Signed-off-by: Eric Evenchick <eric@evenchick.com>
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modify struct gs_host_frame to make use of a union and
DECLARE_FLEX_ARRAY to be able to store different data (lengths), which
will be added in later commits.
Store the gs_host_frame length in TX direction (host -> device) in
struct gs_can::hf_size_tx and RX direction (device -> host) in struct
gs_usb::hf_size_rx so it must be calculated only once.
Link: https://lore.kernel.org/all/20220309124132.291861-15-mkl@pengutronix.de
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some STM32G3 chips support up to 3 CAN-FD channels, increase number of
supported channels in this driver to 3 accordingly.
Link: https://lore.kernel.org/all/20220309124132.291861-14-mkl@pengutronix.de
Suggested-by: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce the variable udev in the gs_usb_probe() function to hold a
pointer to the struct usb_device. This avoids recalculating the value
several times in this function.
Link: https://lore.kernel.org/all/20220309124132.291861-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The widely used open source firmware candleLight has optional support
for reading/writing of an user defined value into the device's flash.
This is indicated by the GS_CAN_FEATURE_USER_ID feature. The
corresponding request are GS_USB_BREQ_GET_USER_ID and
GS_USB_BREQ_SET_USER_ID.
This patch documents these values.
Link: https://lore.kernel.org/all/20220309124132.291861-11-mkl@pengutronix.de
Link: 1453d70dc9
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the binary interface a feature bit might have a corresponding mode
bit (of the same value).
The GS_CAN_FEATURE_IDENTIFY feature doesn't come with a mode. Document
this, to avoid gaps when adding more features/modes later.
Link: https://lore.kernel.org/all/20220309124132.291861-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Newer versions of the widely used open source firmware candleLight
support hardware timestamps. The support is activated by setting the
GS_CAN_MODE_HW_TIMESTAMP in the GS_USB_BREQ_MODE request.
Although timestamp support is not yet supported by this driver, add
the missing bit for documentation purpose.
Link: https://lore.kernel.org/all/20220309124132.291861-9-mkl@pengutronix.de
Link: 44431f4a43
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adds support for the CANFD IP variant in the V3U SoC.
Differences to controllers in other SoCs are limited to an increase in
the number of channels from two to eight, an absence of dedicated
registers for "classic" CAN mode, and a number of differences in magic
numbers (register offsets and layouts).
Inspired by BSP patch by Kazuya Mizuguchi.
Link: https://lore.kernel.org/all/20220309162609.3726306-2-uli+renesas@fpond.eu
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Function es58x_fd_rx_event() invokes the es58x_check_msg_len() macro:
| ret = es58x_check_msg_len(es58x_dev->dev, *rx_event_msg, msg_len);
While doing so, it dereferences an uninitialized
variable: *rx_event_msg.
This is actually harmless because es58x_check_msg_len() only uses
preprocessor macros (sizeof() and __stringify()) on
*rx_event_msg. c.f. [1].
Nonetheless, this pattern is confusing so the lines are reordered to
make sure that rx_event_msg is correctly initialized.
This patch also fixes a false positive warning reported by cppcheck:
| cppcheck possible warnings: (new ones prefixed by >>, may not be real problems)
|
| In file included from drivers/net/can/usb/etas_es58x/es58x_fd.c:
| >> drivers/net/can/usb/etas_es58x/es58x_fd.c:174:8: warning: Uninitialized variable: rx_event_msg [uninitvar]
| ret = es58x_check_msg_len(es58x_dev->dev, *rx_event_msg, msg_len);
| ^
[1] https://elixir.bootlin.com/linux/v5.16/source/drivers/net/can/usb/etas_es58x/es58x_core.h#L467
Link: https://lore.kernel.org/all/20220306101302.708783-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380 ("can: add Virtual CAN Tunnel driver (vxcan)")
Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With can_create_echo_skb() the skb which is forwarded to the peer CAN
interface shares the sk pointer from the originating socket.
This makes the CAN frame show up in the peer namespace as a TX packet.
With the use of skb_clone() analogue to the handling in gw.c the peer
skb gets a new start in the peer namespace and correctly appears as
a RX packet.
Link: https://lore.kernel.org/all/20220309120416.83514-4-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-can@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmIdBQAACgkQJNaLcl1U
h9D1GQf/dVustBx4kCUNJt4QuMF4rozHtAzo2qK1grAnpHEqiMvVEzAuxfbTgJOx
9AUj+xEuVpPxoYUDLVJpJrxwdAl0Ue8tDRgP9Cqr/o6a3IoKrhEi+1KpSbvjcsgB
oqJEcvdjk1XAtl+QXmvyMjbMLxpz2x3Ne6dj7RL/LsfxXC0/om+NQIvJBfn78Dj2
JSNJcVtRDmdaApXfguDGA0u3COarypybYMuumIO4rRxjA5S4FXXovny4nwNXvOhS
Ki5/7GKq9rojeeIf0kD/IDdkmSS0WZp3Rc2mIrdsrXrTca+dTo3sYlcP+HMcZmtW
0+bzsht6VyApfGGZ1Ra/w3NxN6OMMg==
=TyvV
-----END PGP SIGNATURE-----
Merge tag 'spi-remove-void' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Register the CAN device only when all the necessary initialization is
completed. This patch makes sure all the data structures and locks are
initialized before registering the CAN device.
Link: https://lore.kernel.org/all/20220221225935.12300-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver uses an atomic_t variable: gs_usb:active_channels to keep
track of the number of opened channels in order to only allocate
memory for the URBs when this count changes from zero to one.
However, the driver does not decrement the counter when an error
occurs in gs_can_open(). This issue is fixed by changing the type from
atomic_t to u8 and by simplifying the logic accordingly.
It is safe to use an u8 here because the network stack big kernel lock
(a.k.a. rtnl_mutex) is being hold. For details, please refer to [1].
[1] https://lore.kernel.org/linux-can/CAMZ6Rq+sHpiw34ijPsmp7vbUpDtJwvVtdV7CvRZJsLixjAFfrg@mail.gmail.com/T/#t
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220214234814.1321599-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver uses an atomic_t variable: struct
es58x_device::opened_channel_cnt to keep track of the number of opened
channels in order to only allocate memory for the URBs when this count
changes from zero to one.
While the intent was to prevent race conditions, the choice of an
atomic_t turns out to be a bad idea for several reasons:
- implementation is incorrect and fails to decrement
opened_channel_cnt when the URB allocation fails as reported in
[1].
- even if opened_channel_cnt were to be correctly decremented,
atomic_t is insufficient to cover edge cases: there can be a race
condition in which 1/ a first process fails to allocate URBs
memory 2/ a second process enters es58x_open() before the first
process does its cleanup and decrements opened_channed_cnt. In
which case, the second process would successfully return despite
the URBs memory not being allocated.
- actually, any kind of locking mechanism was useless here because
it is redundant with the network stack big kernel lock
(a.k.a. rtnl_lock) which is being hold by all the callers of
net_device_ops:ndo_open() and net_device_ops:ndo_close(). c.f. the
ASSERST_RTNL() calls in __dev_open() [2] and __dev_close_many()
[3].
The atmomic_t is thus replaced by a simple u8 type and the logic to
increment and decrement es58x_device:opened_channel_cnt is simplified
accordingly fixing the bug reported in [1]. We do not check again for
ASSERST_RTNL() as this is already done by the callers.
[1] https://lore.kernel.org/linux-can/20220201140351.GA2548@kili/T/#u
[2] https://elixir.bootlin.com/linux/v5.16/source/net/core/dev.c#L1463
[3] https://elixir.bootlin.com/linux/v5.16/source/net/core/dev.c#L1541
Fixes: 8537257874 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Link: https://lore.kernel.org/all/20220212112713.577957-1-mailhol.vincent@wanadoo.fr
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch prepares the driver to use more than one RX-FIFO. Having a
bigger RX buffer is beneficial in high load situations, where the
system temporarily cannot keep up reading CAN frames from the chip.
Using a bigger RX buffer also allows to implement RX IRQ coalescing,
which will be added in a later patch series.
If using more than 1 RX-FIFO the driver has to figure out, which FIFOs
have RX'ed CAN frames pending. This is indicated by a set bit in the
RXIF register, which is positioned directly after the interrupt status
register INT. If more than 1 RX-FIFO is used, the driver reads both
registers in 1 transfer.
The mcp251xfd_handle_rxif() function iterates over all RX rings and
reads out the RX'ed CAN frames for for all pending FIFOs. To keep the
logic for the 1 RX-FIFO only case in mcp251xfd_handle_rxif() simple,
the driver marks that FIFO pending in mcp251xfd_ring_init().
The chip has a dedicated RX interrupt line to signal pending RX'ed
frames. If connected to an input GPIO and the driver will skip the
initial read of the interrupt status register (INT) and directly read
the pending RX'ed frames if the line is active. The driver assumes the
1st RX-FIFO pending (a read of the RXIF register would re-introduce
the skipped initial read of the INT register). Any other pending
RX-FIFO will be served in the main interrupt handler.
Link: https://lore.kernel.org/all/20220217103826.2299157-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The recent change of the order of the TX and RX FIFOs is not reflected
in the debug info of the FIFO setup. This patch adjust the order and
additionally prints the base address of each FIFO.
Since the mcp251xfd_ring_init() may fail due to wrongly configured
FIFOs, printing of the FIFO setup is moved there. In case of an error
it would not be printed in mcp251xfd_ring_init().
Link: https://lore.kernel.org/all/20220217103826.2299157-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With this patch the usage of the on-chip RAM is checked. In the
current driver the FIFO setup is fixed and always fits into the RAM.
With an upcoming patch series the ring and FIFO setup will be more
dynamic. Although using more RAM than available should not happen, but
add this safety check, just in case.
Link: https://lore.kernel.org/all/20220217103826.2299157-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch actually changes the order of the TX and RX FIFOs.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch improves the initialization of the TX and RX rings. The
initialization functions are now called with pointers to the next free
address (in the on chip RAM) and next free hardware FIFO. The rings
are initialized using these values and the pointers are modified to
point to the next free elements.
This means the order of the mcp251xfd_ring_init_*() functions
specifies the order of the rings in the hardware FIFO. This makes it
possible to change the order of the TX and RX FIFOs, which is done in
the next patch.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch splits the initialization of the TEF, TX and RX FIFO in the
mcp251xfd_ring_init() function into separate functions. This is a
preparation patch to move the RX FIFO in front of the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes the hard coded assumption that the TX ring uses
hardware FIFO 1. This allows the hardware FIFO 1 to be used for RX and
the next free FIFO for TX.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PLL is enabled if the configured clock is less than or equal to 10 times
the max clock frequency.
The device will operate with two different SPI speeds. A slow speed determined
by the clock without the PLL enabled, and a fast speed derived from the
frequency with the PLL enabled.
Link: https://lore.kernel.org/all/20220207131047.282110-16-mkl@pengutronix.de
Link: https://lore.kernel.org/all/20201015124401.2766-3-mas@csselectronics.com
Co-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch prepares the mcp251xfd_chip_clock_init() function for PLL
support.
If the PLL is needed is must be switched on after chip reset. This
should be done in the mcp251xfd_chip_clock_init() function. Prepare
this function to wait for the OSC and PLL to be ready.
Link: https://lore.kernel.org/all/20220207131047.282110-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames mcp251xfd_chip_clock_enable() into mcp251xfd_chip_wake() as
this function actually wakes the chip. Additionally the documentation is
adopted.
Link: https://lore.kernel.org/all/20220207131047.282110-12-mkl@pengutronix.de
Co-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out the timestamp initialization from the clock
initialization.
This is a preparation patch for the PLL support, where clock and
timestamp init must be done separately.
Link: https://lore.kernel.org/all/20220207131047.282110-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the order of reading the Mode and Oscillator Ready
bits.
Instead of reading the Mode of the chip directly after reset, first
wait for the oscillator to get ready and the chip to fully start up.
Read the Mode after this.
Link: https://lore.kernel.org/all/20220207131047.282110-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready. By passing the
appropriate parameters (osc_reference and osc_mask) it can also poll
for PLL ready.
This patch adjusts the error message if the Oscillator and/or PLL fail
to get ready.
Link: https://lore.kernel.org/all/20220207131047.282110-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready.
This is the first register the driver reads from. Reading implausible
values (all bits set or unset) can be caused by the chip starting up
after power on, waking up after sleep, or by the chip not being preset
at all. Add check for implausible register content
mcp251xfd_reg_invalid() to the regmap_read_poll_timeout() loop.
In case of a regmap_read_poll_timeout() returns a fatal error (and not
a timeout), forward it to the caller.
As mcp251xfd_chip_wait_for_osc_ready() will be called after the probe
function has finished, (currently during ifup), move error message
about failed chip detection from there into the probe function.
Link: https://lore.kernel.org/all/20220207131047.282110-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd_chip_stop() function tries the best to stop the chip and
put it into sleep mode. It continues, even if some intermediate steps
fail. As none of the callers use the return value, let this function
return void.
Link: https://lore.kernel.org/all/20220207131047.282110-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd driver supports runtime PM enabled kernels, but also
works on !CONFIG_PM configurations.
This patch simplifies the runtime PM handling in the
mcp251xfd_unregister(). In the CONFIG_PM case, runtime PM has been
enabled in the mcp251xfd_probe() function, so we can disable it here.
For !CONFIG_PM builds call mcp251xfd_clks_and_vdd_disable() directly.
Link: https://lore.kernel.org/all/20220207131047.282110-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
MCP251XFD_REG_OSC is the first register the driver reads from. The
chip may be in deep sleep and the SPI transfer (i.e. the assertion of
the CS) will wake the chip up. This takes about 3ms. The CRC of this
transfer is wrong, or there isn't any chip at all, in this case the
CRC will be wrong, too. The driver ignores the CRC error and returns
the read data to the caller.
To avoid any confusion, this patch changes the
mcp251xfd_regmap_crc_read() function to only ignore the CRC error if
solely the OSC register is read. So when reading more than the OSC
registers at once, CRC errors are not ignored.
Link: https://lore.kernel.org/all/20220207131047.282110-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames mcp251xfd_osc_invalid() to mcp251xfd_reg_invalid(),
as it will be used for other registers than the "osc" register in a
later patch.
This patch also moves this function to more towards the beginning of
the file, to be available for other functions, too.
Link: https://lore.kernel.org/all/20220207131047.282110-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The input to the GENMASK() macro was calculated by hand. Replaced it
with a dedicated macro: BITS_PER_TYPE() which does the exact same job.
Link: https://lore.kernel.org/all/20220212130737.3008-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return value from softing_startstop() directly instead of taking this
in another redundant variable.
Link: https://lore.kernel.org/all/20220112080629.667191-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ethtool core implements a default drvinfo.
There's no need to replicate this in the driver, no additional
information is added, so remove this and rely on the default.
Link: https://lore.kernel.org/all/20220124215642.3474154-10-mkl@pengutronix.de
Cc: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function usb_bulk_msg() can be called with a NULL pointer as the
"actual_length" parameter. This patch removes this variable.
Link: https://lore.kernel.org/all/20220124215642.3474154-9-mkl@pengutronix.de
Cc: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch simplifies the validation of the fixed bit rates. If a
supported bit rate is found, directly return 0.
If no valid bit rate is found return -EINVAL;
Link: https://lore.kernel.org/all/20220124215642.3474154-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The flexcan IP core on the MCF5441X cannot receive CAN RTR messages
via mailboxes. However the mailbox mode is more performant. The commit
| 1c45f5778a ("can: flexcan: add ethtool support to change rx-rtr setting during runtime")
added support to switch from FIFO to mailbox mode on these cores.
After testing the mailbox mode on the MCF5441X by Angelo Dureghello,
this patch marks it (without RTR capability) as supported. Further the
IP core overview table is updated, that RTR reception via mailboxes is
not supported.
Link: https://lore.kernel.org/all/20220121084425.3141218-1-mkl@pengutronix.de
Tested-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.
This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.
Fixes: 6e1caaf8ed ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch
| e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
bulk read/write support has been added to the m_can_fifo_{read,write}
functions.
That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:
| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22
This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.
Fixes: e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver
cleanups. This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYd7Q0g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn3FACgoFZEFY04TU+Cd9mrlRq/mazZm/IAniJfPxOF
U0s57L5o1dlnmawh8mmV
=HSOB
-----END PGP SIGNATURE-----
Merge tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
Link: https://lore.kernel.org/all/20220108181633.420433-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
[mkl: port to net-next/master, replace __sw_hweight64 by simpler calculation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
Link: https://lore.kernel.org/all/20220107193105.1699523-6-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Co-developed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.
This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.
Link: https://lore.kernel.org/all/20220107193105.1699523-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.
The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:
| FLEXCAN_TX_MB_RESERVED_OFF_FIFO -> FLEXCAN_TX_MB_RESERVED_RX_FIFO
| FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP -> FLEXCAN_TX_MB_RESERVED_RX_MAILBOX
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP -> FLEXCAN_QUIRK_USE_RX_MAILBOX
Link: https://lore.kernel.org/all/20220107193105.1699523-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch for the upcoming support to change the
rx-rtr capability via the ethtool API.
Link: https://lore.kernel.org/all/20220107193105.1699523-3-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
Link: https://lore.kernel.org/all/20220105154300.1258636-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
Link: https://lore.kernel.org/all/20220105154300.1258636-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch
| dd8088d5a8 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
Link: https://lore.kernel.org/all/20220105154300.1258636-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Link: https://lore.kernel.org/all/20220105154300.1258636-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Clang static analysis reports this problem
janz-ican3.c:1311:2: warning: Undefined or garbage value returned to caller
return dlc;
^~~~~~~~~~
dlc is only set with this conditional
if (!(cf->can_id & CAN_RTR_FLAG))
dlc = cf->len;
But is always returned. So initialize dlc to 0.
Fixes: cc4b08c31b ("can: do not increase tx_bytes statistics for RTR frames")
Link: https://lore.kernel.org/all/20220108143319.3986923-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently, the CAN netlink interface provides no easy ways to check
the capabilities of a given controller. The only method from the
command line is to try each CAN_CTRLMODE_* individually to check
whether the netlink interface returns an -EOPNOTSUPP error or not
(alternatively, one may find it easier to directly check the source
code of the driver instead...)
This patch introduces a method for the user to check both the
supported and the static capabilities. The proposed method introduces
a new IFLA nest: IFLA_CAN_CTRLMODE_EXT which extends the current
IFLA_CAN_CTRLMODE. This is done to guaranty a full forward and
backward compatibility between the kernel and the user land
applications.
The IFLA_CAN_CTRLMODE_EXT nest contains one single entry:
IFLA_CAN_CTRLMODE_SUPPORTED. Because this entry is only used in one
direction: kernel to userland, no new struct nla_policy are
introduced.
Below table explains how IFLA_CAN_CTRLMODE_SUPPORTED (hereafter:
"supported") and can_ctrlmode::flags (hereafter: "flags") allow us to
identify both the supported and the static capabilities, when masked
with any of the CAN_CTRLMODE_* bit flags:
supported & flags & Controller capabilities
CAN_CTRLMODE_* CAN_CTRLMODE_*
-----------------------------------------------------------------------
false false Feature not supported (always disabled)
false true Static feature (always enabled)
true false Feature supported but disabled
true true Feature supported and enabled
Link: https://lore.kernel.org/all/20211213160226.56219-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Previous patch removed can_priv::ctrlmode_static to replace it with
can_get_static_ctrlmode().
A condition sine qua non for this to work is that the controller
static modes should never be set in can_priv::ctrlmode_supported
(c.f. the comment on can_priv::ctrlmode_supported which states that it
is for "options that can be *modified* by netlink"). Also, this
condition is already correctly fulfilled by all existing drivers
which rely on the ctrlmode_static feature.
Nonetheless, we added an extra safeguard in can_set_static_ctrlmode()
to return an error value and to warn the developer who would be
adventurous enough to set to static a given feature that is already
set to supported.
The drivers which rely on the static controller mode are then updated
to check the return value of can_set_static_ctrlmode().
Link: https://lore.kernel.org/all/20211213160226.56219-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statically enabled features of a CAN controller can be retrieved
using below formula:
| u32 ctrlmode_static = priv->ctrlmode & ~priv->ctrlmode_supported;
As such, there is no need to store this information. This patch remove
the field ctrlmode_static of struct can_priv and provides, in
replacement, the inline function can_get_static_ctrlmode() which
returns the same value.
Link: https://lore.kernel.org/all/20211213160226.56219-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec2 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The field dev_port of struct net_device indicates the port number of a
network device [1]. This patch populates this field.
This field can be helpful to distinguish between the two network
interfaces of a dual channel device (i.e. ES581.4 or ES582.1). Indeed,
at the moment, all the network interfaces of a same device share the
same static udev attributes c.f. output of:
| udevadm info --attribute-walk /sys/class/net/canX
The dev_port attribute can then be used to write some udev rules to,
for example, assign a permanent name to each network interface based
on the serial/dev_port pair (which is convenient when you have a test
bench with several CAN devices connected simultaneously and wish to
keep consistent interface names upon reboot).
[1] https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net
Link: https://lore.kernel.org/all/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Suggested-by: Lukas Magel <lukas.magel@escrypt.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmG/rsoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGLW8H/0sfRUxZNJ+DgO6W
0LpyIx1DF7S2x1wOQGl7VZsjdy+dtuOW4BtEoqhuQWgQ2sr0zbavbeyZYTXD1+d6
I1h5C6JMD138JkoqZNdeyWwsalAFtVItH+lzszUGKTxueTbKCJTkGMerBZVu/gVY
U3QYZHEkUH6o/2fINYfSMhEgyJpjVEUoaztB2drsC0tNUGeDjTmrhlRrWIKZ6Kn+
oAiMqsomSBF09TZ++GEqMYDTm39CwNDPJzKGyyOx86ydcg4ErWvjp1jfAUX0cvFG
dso2K5mDzTewdF8bW0A1KvsQaliMFpxgZ5CTblYQ6HvyltjRj+0B8207VzHQXBKV
YFZ8y9A=
=mfug
-----END PGP SIGNATURE-----
Merge 5.16-rc6 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Check the direction bit in the error frame packet (EPACK) to determine
which net_device_stats {rx,tx}_errors counter to increase.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/all/20211208152122.250852-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When deferred the reason is saved for further debugging. Besides that,
it's fine to call dev_err_probe() in ->probe() when error code is
known. Convert the driver to use dev_err_probe().
Link: https://lore.kernel.org/all/20211206165542.69887-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some configurations, mainly ACPI-based, the clock frequency of the
device is supplied by very well established 'clock-frequency'
property. Hence, try to get it from the property at last if no other
providers are available.
Link: https://lore.kernel.org/all/20211206165542.69887-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's not clear what was the intention of redundant usage of IS_ERR()
around the clock pointer since with the error check of devm_clk_get()
followed by bailout it can't be invalid,
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). It will allow to switch to device properties
approach in the future.
Link: https://lore.kernel.org/all/20211206165542.69887-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Allwinner R40 (also known as A40i, T3, V40) has a CAN controller. The
controller is the same as in earlier A10 and A20 SoCs, but needs reset
line to be deasserted before use.
This patch adds a new compatible for R40 CAN controller. Depending
on the compatible, reset line can be requested from DT.
Link: https://lore.kernel.org/all/20211122104616.537156-3-boger@wirenboard.com
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In [1], we introduced a set of units in linux/can/bittiming.h. Since
then, generic SI prefixes were added to linux/units.h in [2]. Those
new prefixes can perfectly replace CAN specific ones.
This patch replaces all occurrences of the CAN units with their
corresponding prefix (from linux/units) and the unit (as a comment)
according to below table.
CAN units SI metric prefix (from linux/units) + unit (as a comment)
------------------------------------------------------------------------
CAN_KBPS KILO /* BPS */
CAN_MBPS MEGA /* BPS */
CAM_MHZ MEGA /* Hz */
The definition are then removed from linux/can/bittiming.h
[1] commit 1d7750760b ("can: bittiming: add CAN_KBPS, CAN_MBPS and
CAN_MHZ macros")
[2] commit 26471d4a6c ("units: Add SI metric prefix definitions")
Link: https://lore.kernel.org/all/20211124014536.782550-1-mailhol.vincent@wanadoo.fr
Suggested-by: Jimmy Assarsson <extja@kvaser.com>
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The relevant datasheet [1] specifies nonstandard limits for the bit timing
parameters. While it is unclear what the exact effect of violating these
limits is, it seems like a good idea to adhere to the documentation.
[1] Intel Atom® x6000E Series, and Intel® Pentium® and Celeron® N and J
Series Processors for IoT Applications Datasheet,
Volume 2 (Book 3 of 3), July 2021, Revision 001
Fixes: cab7ffc032 ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Link: https://lore.kernel.org/all/9eba5d7c05a48ead4024ffa6e5926f191d8c6b38.1636967198.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing the CAN controller on our Ekhart Lake hardware, we
determined that all communication was running with twice the configured
bitrate. Changing the reference clock rate from 100MHz to 200MHz fixed
this. Intel's support has confirmed to us that 200MHz is indeed the
correct clock rate.
Fixes: cab7ffc032 ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Link: https://lore.kernel.org/all/c9cf3995f45c363e432b3ae8eb1275e54f009fc8.1636967198.git.matthias.schiffer@ew.tq-group.com
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The same fix that was previously done in m_can_platform in commit
99d173fbe8 ("can: m_can: fix iomap_read_fifo() and iomap_write_fifo()")
is required in m_can_pci as well to make iomap_read_fifo() and
iomap_write_fifo() work for val_count > 1.
Fixes: 812270e544 ("can: m_can: Batch FIFO writes during CAN transmit")
Fixes: 1aa6772f64 ("can: m_can: Batch FIFO reads during CAN receive")
Link: https://lore.kernel.org/all/20211118144011.10921-1-matthias.schiffer@ew.tq-group.com
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In m_can_read_fifo(), if the second call to m_can_fifo_read() fails,
the function jump to the out_fail label and returns without calling
m_can_receive_skb(). This means that the skb previously allocated by
alloc_can_skb() is not freed. In other terms, this is a memory leak.
This patch adds a goto label to destroy the skb if an error occurs.
Issue was found with GCC -fanalyzer, please follow the link below for
details.
Fixes: e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20211107050755.70655-1-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/all/20211129222628.7490-1-brian.silverman@bluerivertech.com
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the last channel is not available then "dev" is freed. Fortunately,
we can just use "pdev->irq" instead.
Also we should check if at least one channel was set up.
Fixes: fd734c6f25 ("can/sja1000: add driver for EMS PCMCIA card")
Link: https://lore.kernel.org/all/20211124145041.GB13656@kili
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After calling netif_receive_skb(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is dereferenced
just after the call netif_receive_skb(skb).
Reordering the lines solves the issue.
Fixes: b21d18b51b ("can: Topcliff: Add PCH_CAN driver.")
Link: https://lore.kernel.org/all/20211123111654.621610-1-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After the previous patches, noone needs 'file' parameter in neither
ioctl hook from tty_ldisc_ops. So remove 'file' from both of them.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> [NFC]
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122094529.24171-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different
from the tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit operations
to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries
to access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ttgq
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different from the
tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the
workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit
operations to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs"
* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
selftests/net: udpgso_bench_rx: fix port argument
net: wwan: iosm: fix compilation warning
cxgb4: fix eeprom len when diagnostics not implemented
net: fix premature exit from NAPI state polling in napi_disable()
net/smc: fix sk_refcnt underflow on linkdown and fallback
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
gve: fix unmatched u64_stats_update_end()
net: ethernet: lantiq_etop: Fix compilation error
selftests: forwarding: Fix packet matching in mirroring selftests
vsock: prevent unnecessary refcnt inc for nonblocking connect
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
net: stmmac: allow a tc-taprio base-time of zero
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
net: hns3: allow configure ETS bandwidth of all TCs
net: hns3: remove check VF uc mac exist when set by PF
net: hns3: fix some mac statistics is always 0 in device version V2
net: hns3: fix kernel crash when unload VF while it is being reset
net: hns3: sync rx ring head in echo common pull
net: hns3: fix pfc packet number incorrect after querying pfc parameters
...
This patch fixes the error handling for mcp251xfd_chip_rx_int_enable().
Instead just returning the error, properly shut down the chip.
Link: https://lore.kernel.org/all/20211106201526.44292-2-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function can_rx_offload_threaded_irq_finish() is needed to trigger
the NAPI thread to deliver read CAN frames to the networking stack.
This patch adds the missing call to can_rx_offload_threaded_irq_finish()
in case of a bus off, before leaving the interrupt handler to avoid
packet starvation.
Link: https://lore.kernel.org/all/20211106201526.44292-1-mkl@pengutronix.de
Fixes: 30bfec4fec ("can: rx-offload: can_rx_offload_threaded_irq_finish(): add new function to be called from threaded interrupt")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since for the PCAN-USB, the management of the transition to the
ERROR_WARNING or ERROR_PASSIVE state is done according to the error
counters, these must be requested unconditionally.
Link: https://lore.kernel.org/all/20211021081505.18223-2-s.grosjean@peak-system.com
Fixes: c11dcee758 ("can: peak_usb: pcan_usb_decode_error(): upgrade handling of bus state changes")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In es58x_rx_err_msg(), if can->do_set_mode() fails, the function
directly returns without calling netif_rx(skb). This means that the
skb previously allocated by alloc_can_err_skb() is not freed. In other
terms, this is a memory leak.
This patch simply removes the return statement in the error branch and
let the function continue.
Issue was found with GCC -fanalyzer, please follow the link below for
details.
Fixes: 8537257874 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Link: https://lore.kernel.org/all/20211026180740.1953265-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPczQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykWbwCfaIScbUoCUx+h/uP93nKKD8B3KgYAoMvFuhhD
D/fTLggs12x5NsvLBgtZ
=rq0R
-----END PGP SIGNATURE-----
Merge tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
The end goal of the current buffer overflow detection work[0] is to gain
full compile-time and run-time coverage of all detectable buffer overflows
seen via array indexing or memcpy(), memmove(), and memset(). The str*()
family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this series
contains the foundational elements of several related buffer overflow
detection improvements by providing new common helpers and FORTIFY_SOURCE
changes needed to gain the introspection required for compiler visibility
into array sizes. Also included are a handful of already Acked instances
using the helpers (or related clean-ups), with many more waiting at the
ready to be taken via subsystem-specific trees[2]. The new helpers are:
- struct_group() for gaining struct member range introspection.
- memset_after() and memset_startat() for clearing to the end of structures.
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs.
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage under
GCC, and to prepare to fix the currently broken Clang support. Finishing
this work is part of the larger series[0], but depends on all the false
positives and buffer overflow bug fixes to have landed already and those
that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time
and run-time tests are added for FORTIFY_SOURCE and the mem*()-family
functions respectively. The compile time tests have found a legitimate
(though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage that
result in no known object code differences.
After this series (and the changes that have now landed via netdev
and usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds. However, due corner cases in
GCC[3] and Clang[4], I have not included the last two patches that turn
on these options, as I don't want to introduce any known warnings to
the build. Hopefully these can be solved soon.
[0] https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE
[2] https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/
[3] https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/
[4] https://bugs.llvm.org/show_bug.cgi?id=51682
[5] https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/
[6] https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/
-----BEGIN PGP SIGNATURE-----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=9xbT
-----END PGP SIGNATURE-----
Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"The end goal of the current buffer overflow detection work[0] is to
gain full compile-time and run-time coverage of all detectable buffer
overflows seen via array indexing or memcpy(), memmove(), and
memset(). The str*() family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this
series contains the foundational elements of several related buffer
overflow detection improvements by providing new common helpers and
FORTIFY_SOURCE changes needed to gain the introspection required for
compiler visibility into array sizes. Also included are a handful of
already Acked instances using the helpers (or related clean-ups), with
many more waiting at the ready to be taken via subsystem-specific
trees[2].
The new helpers are:
- struct_group() for gaining struct member range introspection
- memset_after() and memset_startat() for clearing to the end of
structures
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in
structs
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage
under GCC, and to prepare to fix the currently broken Clang support.
Finishing this work is part of the larger series[0], but depends on
all the false positives and buffer overflow bug fixes to have landed
already and those that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a
compile-time and run-time tests are added for FORTIFY_SOURCE and the
mem*()-family functions respectively. The compile time tests have
found a legitimate (though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage
that result in no known object code differences.
After this series (and the changes that have now landed via netdev and
usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds.
However, due corner cases in GCC[3] and Clang[4], I have not included
the last two patches that turn on these options, as I don't want to
introduce any known warnings to the build. Hopefully these can be
solved soon"
Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1]
Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2]
Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3]
Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4]
Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5]
Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6]
* tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
fortify: strlen: Avoid shadowing previous locals
compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer
treewide: Replace 0-element memcpy() destinations with flexible arrays
treewide: Replace open-coded flex arrays in unions
stddef: Introduce DECLARE_FLEX_ARRAY() helper
btrfs: Use memset_startat() to clear end of struct
string.h: Introduce memset_startat() for wiping trailing members and padding
xfrm: Use memset_after() to clear padding
string.h: Introduce memset_after() for wiping trailing members/padding
lib: Introduce CONFIG_MEMCPY_KUNIT_TEST
fortify: Add compile-time FORTIFY_SOURCE tests
fortify: Allow strlen() and strnlen() to pass compile-time known lengths
fortify: Prepare to improve strnlen() and strlen() warnings
fortify: Fix dropped strcpy() compile-time write overflow check
fortify: Explicitly disable Clang support
fortify: Move remaining fortify helpers into fortify-string.h
lib/string: Move helper functions out of string.c
compiler_types.h: Remove __compiletime_object_size()
cm4000_cs: Use struct_group() to zero struct cm4000_dev region
can: flexcan: Use struct_group() to zero struct flexcan_regs regions
...
Since netif_napi_del() is already done in the free_candev(), we remove
this redundant netif_napi_del() invocation. In addition, this patch
can match the operations in the xcan_probe() and xcan_remove()
functions.
Link: https://lore.kernel.org/all/20211017125022.3100329-1-mudongliangabcd@gmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch allows to use the whole 64-bit timestamps received from the
CAN-FD device (expressed in µs) rather than only its low part, in the
hwtstamp structure of the skb transferred to the network layer, when a
CAN/CANFD frame has been received.
Link: https://lore.kernel.org/all/20210930094603.23134-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Link: https://lore.kernel.org/all/20210915145726.7092-1-caihuoqing@baidu.com
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sysfs show() functions must not use snprintf() when formatting the
value to be returned to user space.
Fix the following coccicheck warning:
| drivers/net/can/at91_can.c:1185: WARNING: use scnprintf or sprintf.
| drivers/net/can/janz-ican3.c:1834: WARNING: use scnprintf or sprintf.
|
| Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Link: https://lore.kernel.org/all/1634280624-4816-1-git-send-email-wangqing@vivo.com
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN device can measure the TDCV (Transmission Delay Compensation
Value) automatically for each transmitted CAN frames.
A callback function do_get_auto_tdcv() is added to retrieve that
value. This function is used only if CAN_CTRLMODE_TDC_AUTO is enabled
(if CAN_CTRLMODE_TDC_MANUAL is selected, the TDCV value is provided by
the user).
If the device does not support reporting of TDCV, do_get_auto_tdcv()
should be set to NULL and TDCV will not be reported by the netlink
interface.
On success, do_get_auto_tdcv() shall return 0. If the value can not be
measured by the device, for example because network is down or because
no frames were transmitted yet, can_priv::do_get_auto_tdcv() shall
return a negative error code (e.g. -EINVAL) to signify that the value
is not yet available. In such cases, TDCV is not reported by the
netlink interface.
Link: https://lore.kernel.org/all/20210918095637.20108-6-mailhol.vincent@wanadoo.fr
CC: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the netlink interface for TDC parameters of struct can_tdc_const
and can_tdc.
Contrary to the can_bittiming(_const) structures for which there is
just a single IFLA_CAN(_DATA)_BITTMING(_CONST) entry per structure,
here, we create a nested entry IFLA_CAN_TDC. Within this nested entry,
additional IFLA_CAN_TDC_TDC* entries are added for each of the TDC
parameters of the newly introduced struct can_tdc_const and struct
can_tdc.
For struct can_tdc_const, these are:
IFLA_CAN_TDC_TDCV_MIN
IFLA_CAN_TDC_TDCV_MAX
IFLA_CAN_TDC_TDCO_MIN
IFLA_CAN_TDC_TDCO_MAX
IFLA_CAN_TDC_TDCF_MIN
IFLA_CAN_TDC_TDCF_MAX
For struct can_tdc, these are:
IFLA_CAN_TDC_TDCV
IFLA_CAN_TDC_TDCO
IFLA_CAN_TDC_TDCF
This is done so that changes can be applied in the future to the
structures without breaking the netlink interface.
The TDC netlink logic works as follow:
* CAN_CTRLMODE_FD is not provided:
- if any TDC parameters are provided: error.
- TDC parameters not provided: TDC parameters unchanged.
* CAN_CTRLMODE_FD is provided and is false:
- TDC is deactivated: both the structure and the
CAN_CTRLMODE_TDC_{AUTO,MANUAL} flags are flushed.
* CAN_CTRLMODE_FD provided and is true:
- CAN_CTRLMODE_TDC_{AUTO,MANUAL} and tdc{v,o,f} not provided: call
can_calc_tdco() to automatically decide whether TDC should be
activated and, if so, set CAN_CTRLMODE_TDC_AUTO and uses the
calculated tdco value.
- CAN_CTRLMODE_TDC_AUTO and tdco provided: set
CAN_CTRLMODE_TDC_AUTO and use the provided tdco value. Here,
tdcv is illegal and tdcf is optional.
- CAN_CTRLMODE_TDC_MANUAL and both of tdcv and tdco provided: set
CAN_CTRLMODE_TDC_MANUAL and use the provided tdcv and tdco
value. Here, tdcf is optional.
- CAN_CTRLMODE_TDC_{AUTO,MANUAL} are mutually exclusive. Whenever
one flag is turned on, the other will automatically be turned
off. Providing both returns an error.
- Combination other than the one listed above are illegal and will
return an error.
N.B. above rules mean that whenever CAN_CTRLMODE_FD is provided, the
previous TDC values will be overwritten. The only option to reuse
previous TDC value is to not provide CAN_CTRLMODE_FD.
All the new parameters are defined as u32. This arbitrary choice is
done to mimic the other bittiming values with are also all of type
u32. An u16 would have been sufficient to hold the TDC values.
This patch completes below series (c.f. [1]):
- commit 289ea9e4ae ("can: add new CAN FD bittiming parameters:
Transmitter Delay Compensation (TDC)")
- commit c25cc79932 ("can: bittiming: add calculation for CAN FD
Transmitter Delay Compensation (TDC)")
[1] https://lore.kernel.org/linux-can/20210224002008.4158-1-mailhol.vincent@wanadoo.fr/T/#t
Link: https://lore.kernel.org/all/20210918095637.20108-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function can_calc_tdco() directly retrieves can_priv from the
net_device and directly modifies it.
This is annoying for the upcoming patch. In
drivers/net/can/dev/netlink.c:can_changelink(), the data bittiming are
written to a temporary structure and memcpyed to can_priv only after
everything succeeded. In the next patch, where we will introduce the
netlink interface for TDC parameters, we will add a new TDC block
which can potentially fail. For this reason, the data bittiming
temporary structure has to be copied after that to-be-introduced TDC
block. However, TDC also needs to access data bittiming information.
We change the prototype so that the data bittiming structure is passed
to can_calc_tdco() as an argument instead of retrieving it from
priv. This way can_calc_tdco() can access the data bittiming before it
gets memcpyed to priv.
Link: https://lore.kernel.org/all/20210918095637.20108-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the current implementation, all Transmission Delay Compensation
(TDC) parameters are expressed in time quantum. However, ISO 11898-1
actually specifies that these should be expressed in *minimum* time
quantum.
Furthermore, the minimum time quantum is specified to be "one node
clock period long" (c.f. paragraph 11.3.1.1 "Bit time"). For sake of
simplicity, we prefer to use the "clock period" term instead of
"minimum time quantum" because we believe that it is more broadly
understood.
This patch fixes that discrepancy by updating the documentation and
the formula for TDCO calculation.
N.B. In can_calc_tdco(), the sample point (in time quantum) was
calculated using a division, thus introducing a risk of rounding and
truncation errors. On top of changing the unit to clock period, we
also modified the formula to use only additions.
Link: https://lore.kernel.org/all/20210918095637.20108-3-mailhol.vincent@wanadoo.fr
Suggested-by: Stefan Mätje <Stefan.Maetje@esd.eu>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ISO 11898-1 specifies in section 11.3.3 "Transmitter delay
compensation" that "the configuration range for [the] SSP position
shall be at least 0 to 63 minimum time quanta."
Because SSP = TDCV + TDCO, it means that we should allow both TDCV and
TDCO to hold zero value in order to honor SSP's minimum possible
value.
However, current implementation assigned special meaning to TDCV and
TDCO's zero values:
* TDCV = 0 -> TDCV is automatically measured by the transceiver.
* TDCO = 0 -> TDC is off.
In order to allow for those values to really be zero and to maintain
current features, we introduce two new flags:
* CAN_CTRLMODE_TDC_AUTO indicates that the controller support
automatic measurement of TDCV.
* CAN_CTRLMODE_TDC_MANUAL indicates that the controller support
manual configuration of TDCV. N.B.: current implementation failed
to provide an option for the driver to indicate that only manual
mode was supported.
TDC is disabled if both CAN_CTRLMODE_TDC_AUTO and
CAN_CTRLMODE_TDC_MANUAL flags are off, c.f. the helper function
can_tdc_is_enabled() which is also introduced in this patch.
Also, this patch adds three fields: tdcv_min, tdco_min and tdcf_min to
struct can_tdc_const. While we are not convinced that those three
fields could be anything else than zero, we can imagine that some
controllers might specify a lower bound on these. Thus, those minimums
are really added "just in case".
Comments of struct can_tdc and can_tdc_const are updated accordingly.
Finally, the changes are applied to the etas_es58x driver.
Link: https://lore.kernel.org/all/20210918095637.20108-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot
be allocated and can_change_state() handles the case when cf is NULL,
the test on the nullity of skb is now unnecessary.
Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The read and writes from the fifo are from a buffer, with various
fields and data at predefined offsets. So, they should not be done to
the same address(or port) in case of val_count greater than 1.
Therefore, fix this by using iowrite32()/ioread32() instead of
ioread32_rep()/iowrite32_rep().
Also, the write into FIFO must be performed with an offset from the
message ram base address. Therefore, fix the base address to
mram_base.
Fixes: e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.com
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the driver was not opened, rcar_can_suspend() should not call
clk_disable() because the clock was not enabled.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com
Cc: stable@vger.kernel.org
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Add struct_group() to mark both regions of struct flexcan_regs that get
initialized to zero. Avoid the future warnings:
In function 'fortify_memset_chk',
inlined from 'memset_io' at ./include/asm-generic/io.h:1169:2,
inlined from 'flexcan_ram_init' at drivers/net/can/flexcan.c:1403:2:
./include/linux/fortify-string.h:199:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
199 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function 'fortify_memset_chk',
inlined from 'memset_io' at ./include/asm-generic/io.h:1169:2,
inlined from 'flexcan_ram_init' at drivers/net/can/flexcan.c:1408:3:
./include/linux/fortify-string.h:199:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
199 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>