[ Upstream commit 96789dce04 ]
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fe2ec59db ]
We have to take care of ID_P_PM_BLOCKED when bailing out during probe.
Fixes: 7ee24eb508 ("i2c: rcar: disable PM in multi-master mode")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5222d408d ]
On some platforms in rare cases (1 to 100,000 transactions),
the i2c gets a spurious interrupt which means that we enter an interrupt
but in the interrupt handler we don't find any status bit that points to
the reason we got this interrupt.
This may be a case of a rare HW issue or signal integrity issue that is
still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is not
enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the
transaction.
On next xmit transaction if the bus is still busy the master will issue a
recovery process before issuing the new transaction.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9f8426d1 ]
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always
incorrect, but simply didn't cause a visible error on the 32-bit machine.
On the 64-bit machine, the kernel message reports that ESR value is
0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that
it's the alignment fault.
SMBnCTL3's address is 0xE.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6977262c2e ]
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8 ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fbb903c8 ]
The supplied buffer might be on the stack and we get the following error
message:
[ 3.312058] at91_i2c e0070600.i2c: rejecting DMA map of vmalloc memory
Use i2c_{get,put}_dma_safe_msg_buf() to get a DMA-able memory region if
necessary.
Fixes: 60937b2cdb ("i2c: at91: add dma support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 690b2549b1 upstream.
The "data->block[0]" variable comes from the user and is a number
between 0-255. It needs to be capped to prevent writing beyond the end
of dma_buffer[].
Fixes: 5e9a97b1f4 ("i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL")
Reported-and-tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03a35bc856 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17a0f3acdc ]
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cf72f4180 upstream.
Enable EFCH MMIO using check for SMBus PCI revision ID value 0x51 or
greater. This PCI revision ID check will enable family 17h and future
AMD processors with the same EFCH SMBus controller HW.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 381a3083c6 upstream.
AMD processors include registers capable of selecting between 2 SMBus
ports. Port selection is made during each user access by writing to
FCH::PM::DECODEEN[smbus0sel]. Change the driver to use MMIO during
SMBus port selection because cd6h/cd7h port I/O is not available on
later AMD processors.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46967bc1ee upstream.
The EFCH SMBus controller's base address is determined using details in
FCH::PM::DECODEEN[smbusasfiobase] and FCH::PM::DECODEEN[smbusasfioen].These
register fields were accessed using cd6h/cd7h port I/O. cd6h/cd7h port I/O
is no longer available in later AMD processors. Change base address
detection to use MMIO instead of port I/O cd6h/cd7h.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c148722d0 upstream.
EFCH cd6h/cd7h port I/O may no longer be available on later AMD
processors and it is recommended to use MMIO instead. Update the
request and release functions to support MMIO.
MMIO request/release and mmapping require details during cleanup.
Add a MMIO configuration structure containing resource and vaddress
details for mapping the region, accessing the region, and releasing
the region.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[wsa: rebased after fixup in previous patch]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbafbd51bf upstream.
Move port selection code into a separate function. Refactor is in
preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a59a24e14 upstream.
Move SMBus controller base address detection into function. Refactor
is in preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3325d225b upstream.
Move duplicated region request and release code into a function. Move is
in preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[wsa: added missing curly brace]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93102cb449 upstream.
Replace number constant with #define to improve readability and
maintainability.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd8963e602 upstream.
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993eb48fa1 upstream.
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638a ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a22aabf20 ]
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb13aa16f3 ]
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d366c2f9d ]
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e138e43a ]
Drop I2C device-probing classes from platform variant of the PASemi
controller as it is only used on platforms where I2C devices should
be instantiated in devicetree. (The I2C_CLASS_DEPRECATED flag is not
raised as up to this point no devices relied on the old behavior.)
Fixes: d88ae2932d ("i2c: pasemi: Add Apple platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b205f58502 ]
Some resource should be released if an error occurs in
'bcm2835_i2c_probe()'.
Add an error handling path and the needed 'clk_disable_unprepare()' and
'clk_rate_exclusive_put()' calls.
While at it, rework the bottom of the function to use this newly added
error handling path and have an explicit and more standard "return 0;" at
the end of the normal path.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
partial support for < MAX_ORDER - 1 granularity for virtio-mem
driver_override for vdpa
sysfs ABI documentation for vdpa
multiqueue config support for mlx5 vdpa
Misc fixes, cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHiDHkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpVT4H/3Veixt3uYPOmuLU2tSx+8X+sFTtik81hyiE
okz5fRJrxxA8SqS76FnmO10FS4hlPOGNk0Z5WVhr0yihwFvPLvpCM/xi2Lmrz9I7
pB0sXOIocEL1xApsxukR9K1Twpb2hfYsflbJYUVlRfhS5G0izKJNZp5I7OPrzd80
vVNNDWKW2iLDlfqsavumI4Kvm4nsFuCHG03jzMtcIa7YTXYV3DORD4ZGFFVUOIQN
t5F74TznwHOeYgJeg7TzjFjfPWmXjLetvx10QX1A1uOvwppWW/QY6My0UafTXNXj
VB3gOwJPf+gxXAXl/4bafq4NzM0xys6cpcPpjvhmU+erY4UuyAU=
=Y1eO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Eliminate the following coccicheck warning:
./drivers/i2c/busses/i2c-sh_mobile.c:849:3-4: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
* iASL/Disassembler: Additional support for NHLT table (Bob Moore).
* Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
* Fix a couple of warnings under MSVC (Bob Moore).
* iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
* iASL/NHLT table: "Specific Data" field support (Bob Moore).
* Use original data_table_region pointer for accesses (Jessica
Clarke).
* Use original pointer for virtual origin tables (Jessica Clarke).
* Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
* Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
* iASL: Add suppport for AGDI table (Ilkka Koskinen).
* Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
* Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
* Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
* Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
* Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
* Fix wrong interpretation of PCC address (Sudeep Holla).
* Add support for PCC Opregion special context data (Sudeep Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
- Rework flushing of EC work while suspended to idle and clean up
the handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used
when the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh).
-----BEGIN PGP SIGNATURE-----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=IGwJ
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are usual ACPICA code updates (although there are more of them
than in the last few releases), a noticeable EC driver update (which
mostly consists of cleanups, though), the device enumeration quirks
handling rework from Hans, some updates eliminating unnecessary CPU
cache flushing in some places (processor idle and system-wide PM code)
and a bunch of assorted cleanups and fixes.
Specifics:
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
- iASL/Disassembler: Additional support for NHLT table (Bob
Moore).
- Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
- Fix a couple of warnings under MSVC (Bob Moore).
- iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
- iASL/NHLT table: "Specific Data" field support (Bob Moore).
- Use original data_table_region pointer for accesses (Jessica
Clarke).
- Use original pointer for virtual origin tables (Jessica Clarke).
- Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
- Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
- iASL: Add suppport for AGDI table (Ilkka Koskinen).
- Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
- Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
- Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
- Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
- Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
- Fix wrong interpretation of PCC address (Sudeep Holla).
- Add support for PCC Opregion special context data (Sudeep
Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system PM
transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang
Li).
- Rework flushing of EC work while suspended to idle and clean up the
handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used when
the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh)"
* tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
ACPI: processor: thermal: avoid cpufreq_get_policy()
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
ACPI: battery: Add the ThinkPad "Not Charging" quirk
ACPI: sysfs: use default_groups in kobj_type
ACPICA: Update version to 20211217
ACPICA: iASL/NHLT table: "Specific Data" field support
ACPICA: iASL: Add suppport for AGDI table
ACPICA: iASL: Add TDEL table to both compiler/disassembler
ACPICA: Fixed a couple of warnings under MSVC
ACPICA: Change a return_ACPI_STATUS (AE_BAD_PARAMETER)
ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
ACPICA: Add support for PCC Opregion special context data
ACPICA: Fix wrong interpretation of PCC address
...
-----BEGIN PGP SIGNATURE-----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=cCwW
-----END PGP SIGNATURE-----
Merge tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: ov5693
- A new driver for STM32 Chrom-ART Accelerator
- Added V4L2 core helper functions for VP9 codec
- Hantro driver has gained support for VP9 codecs
- Added support for Maxim MAX96712 Quad GMSL2 Deserializer
- The staging atomisp driver has gained lots of improvements, fixes and
cleanups. It now works with userptr
- Lots of random driver improvements as usual
* tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (397 commits)
media: ipu3-cio2: Add support for instantiating i2c-clients for VCMs
media: ipu3-cio2: Call cio2_bridge_init() before anything else
media: ipu3-cio2: Defer probing until the PMIC is fully setup
media: hantro: Add support for Allwinner H6
media: dt-bindings: allwinner: document H6 Hantro G2 binding
media: hantro: Convert imx8m_vpu_g2_irq to helper
media: hantro: move postproc enablement for old cores
media: hantro: vp9: add support for legacy register set
media: hantro: vp9: use double buffering if needed
media: hantro: add support for reset lines
media: hantro: Fix probe func error path
media: i2c: hi846: use pm_runtime_force_suspend/resume for system suspend
media: i2c: hi846: check return value of regulator_bulk_disable()
media: hi556: Support device probe in non-zero ACPI D state
media: ov5675: Support device probe in non-zero ACPI D state
media: imx208: Support device probe in non-zero ACPI D state
media: ov2740: support device probe in non-zero ACPI D state
media: ov5670: Support device probe in non-zero ACPI D state
media: ov8856: support device probe in non-zero ACPI D state
media: ov8865: Disable only enabled regulators on error path
...
These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols,
the MAINTAINERS file, and removing some dead code.
-----BEGIN PGP SIGNATURE-----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=8wnp
-----END PGP SIGNATURE-----
Merge tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols, the
MAINTAINERS file, and removing some dead code"
* tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: exynos: Enable Exynos Multi-Core Timer driver
ARM: ixp4xx: remove unused header file pata_ixp4xx_cf.h
ARM: ixp4xx: remove dead configs CPU_IXP43X and CPU_IXP46X
MAINTAINERS: Add Florian as BCM5301X and BCM53573 maintainer
ARM: samsung: Remove HAVE_S3C2410_I2C and use direct dependencies
ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART
ARM: imx: remove dead left-over from i.MX{27,31,35} removal
ARM: s3c: add one more "fallthrough" statement in Jive
ARM: s3c: include header for prototype of s3c2410_modify_misccr
ARM: shmobile: rcar-gen2: Add missing of_node_put()
Merge ACPI device enumeration updates, ACPI power management updates
and PCI host bridge ACPI driver updates for 5.17-rc1:
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
* acpi-scan:
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
ACPI: Use acpi_fetch_acpi_dev() instead of acpi_bus_get_device()
ACPI: scan: Introduce acpi_fetch_acpi_dev()
ACPI: scan: Do not add device IDs from _CID if _HID is not valid
* acpi-pm:
ACPI: PM: Remove redundant cache flushing
ACPI: PM: Avoid CPU cache flush when entering S4
* acpi-power:
ACPI: PM: Emit debug messages when enabling/disabling wakeup power
* acpi-pci:
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
This largely reverts commit 5a7b95fb99. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.
Fixes: 5a7b95fb99 ("i2c: core: support bus regulator controlling in adapter")
Reported-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Link: https://lore.kernel.org/r/1295184560.182511.1639075777725@mail.yahoo.com
Reported-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Link: https://lore.kernel.org/r/7143a7147978f4104171072d9f5225d2ce355ec1.camel@yandex.ru
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1850
Tested-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # 5.14+
When performing an I2C transfer where the last message was a write KASAN
would complain:
BUG: KASAN: slab-out-of-bounds in mpc_i2c_do_action+0x154/0x630
Read of size 2 at addr c814e310 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G B 5.16.0-rc8 #1
Call Trace:
[e5ee9d50] [c08418e8] dump_stack_lvl+0x4c/0x6c (unreliable)
[e5ee9d70] [c02f8a14] print_address_description.constprop.13+0x64/0x3b0
[e5ee9da0] [c02f9030] kasan_report+0x1f0/0x204
[e5ee9de0] [c0c76ee4] mpc_i2c_do_action+0x154/0x630
[e5ee9e30] [c0c782c4] mpc_i2c_isr+0x164/0x240
[e5ee9e60] [c00f3a04] __handle_irq_event_percpu+0xf4/0x3b0
[e5ee9ec0] [c00f3d40] handle_irq_event_percpu+0x80/0x110
[e5ee9f40] [c00f3e48] handle_irq_event+0x78/0xd0
[e5ee9f60] [c00fcfec] handle_fasteoi_irq+0x19c/0x370
[e5ee9fa0] [c00f1d84] generic_handle_irq+0x54/0x80
[e5ee9fc0] [c0006b54] __do_irq+0x64/0x200
[e5ee9ff0] [c0007958] __do_IRQ+0xe8/0x1c0
[c812dd50] [e3eaab20] 0xe3eaab20
[c812dd90] [c0007a4c] do_IRQ+0x1c/0x30
[c812dda0] [c0000c04] ExternalInput+0x144/0x160
--- interrupt: 500 at arch_cpu_idle+0x34/0x60
NIP: c000b684 LR: c000b684 CTR: c0019688
REGS: c812ddb0 TRAP: 0500 Tainted: G B (5.16.0-rc8)
MSR: 00029002 <CE,EE,ME> CR: 22000488 XER: 20000000
GPR00: c10ef7fc c812de90 c80ff200 c2394718 00000001 00000001 c10e3f90 00000003
GPR08: 00000000 c0019688 c2394718 fc7d625b 22000484 00000000 21e17000 c208228c
GPR16: e3e99284 00000000 ffffffff c2390000 c001bac0 c2082288 c812df60 c001ba60
GPR24: c23949c0 00000018 00080000 00000004 c80ff200 00000002 c2348ee4 c2394718
NIP [c000b684] arch_cpu_idle+0x34/0x60
LR [c000b684] arch_cpu_idle+0x34/0x60
--- interrupt: 500
[c812de90] [c10e3f90] rcu_eqs_enter.isra.60+0xc0/0x110 (unreliable)
[c812deb0] [c10ef7fc] default_idle_call+0xbc/0x230
[c812dee0] [c00af0e8] do_idle+0x1c8/0x200
[c812df10] [c00af3c0] cpu_startup_entry+0x20/0x30
[c812df20] [c001e010] start_secondary+0x5d0/0xba0
[c812dff0] [c00028a0] __secondary_start+0x90/0xdc
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional() for DT users only.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
x86 ACPI devices which ship with only Android as their factory image
usually declare a whole bunch of bogus I2C devices in their ACPI tables.
Instantiating I2C clients for these bogus devices causes various issues,
e.g. GPIO/IRQ resource conflicts because sometimes drivers do bind to them.
The Android x86 kernel fork shipped on these devices has some special code
to remove these bogus devices, instead of just fixing the DSDT <sigh>.
Use the new acpi_quirk_skip_i2c_client_enumeration() helper to identify
known boards / acpi devices with this issue, and skip enumerating these.
Note these boards typically do actually have I2C devices, just
different ones then the ones described in their DSDT. The devices
which are actually present are manually instantiated by the
drivers/platform/x86/x86-android-tablets.c kernel module.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No symbols from the linux/irqchip/chained_irq.h and linux/irqdomain.h
headers are used in the driver, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the DMA setup and callback
were superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Lucas Tanure