[ Upstream commit bcd8a45223 ]
Executing driver on servers with more than 32 CPUs were faced with command
timeouts. This is because we were not geting completions for commands
submitted on IQ32 - IQ63.
Set E64Q bit to enable upper inbound and outbound queues 32 to 63 in the
MPI main configuration table.
Added 500ms delay after successful MPI initialization as mentioned in
controller datasheet.
Link: https://lore.kernel.org/r/20220411064603.668448-3-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294080eacf ]
When upper inbound and outbound queues 32-63 are enabled, we see upper
vectors 32-63 in interrupt service routine. We need corresponding registers
to handle masking and unmasking of these upper interrupts.
To achieve this, we use registers MSGU_ODMR_U(0x34) to mask and
MSGU_ODMR_CLR_U(0x3C) to unmask the interrupts. In these registers bit 0-31
represents interrupt vectors 32-63.
Link: https://lore.kernel.org/r/20220411064603.668448-2-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f792a3629f ]
In pm8001_chip_fw_flash_update_build(), if
pm8001_chip_fw_flash_update_build() fails, the struct fw_control_ex
allocated must be freed.
Link: https://lore.kernel.org/r/20220220031810.738362-23-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c8f04b190 ]
In pm8001_chip_set_dev_state_req(), pm8001_chip_fw_flash_update_req(),
pm80xx_chip_phy_ctl_req() and pm8001_chip_reg_dev_req() add missing calls
to pm8001_tag_free() to free the allocated tag when pm8001_mpi_build_cmd()
fails.
Similarly, in pm8001_exec_internal_task_abort(), if the chip ->task_abort
method fails, the tag allocated for the abort request task must be
freed. Add the missing call to pm8001_tag_free().
Link: https://lore.kernel.org/r/20220220031810.738362-22-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f90a74892f ]
In pm8001_send_abort_all(), make sure to free the allocated sas task
if pm8001_tag_alloc() or pm8001_mpi_build_cmd() fail.
Link: https://lore.kernel.org/r/20220220031810.738362-21-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fb23a785b ]
The function pm8001_tag_alloc() determines free tags using the function
find_first_zero_bit() which can return 0 when the first bit of the bitmap
being inspected is 0. As such, tag 0 is a valid tag value that should not
be dismissed as invalid. Fix the functions pm8001_work_fn(),
mpi_sata_completion(), pm8001_mpi_task_abort_resp() and
pm8001_open_reject_retry() to not dismiss 0 tags as invalid.
The value 0xffffffff is used for invalid tags for unused ccb information
structures. Add the macro definition PM8001_INVALID_TAG to define this
value.
Link: https://lore.kernel.org/r/20220220031810.738362-20-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e6b7e740a ]
The call to pm8001_ccb_task_free() at the end of
pm8001_mpi_task_abort_resp() already frees the ccb tag. So when the device
NCQ_ABORT_ALL_FLAG is set, the tag should not be freed again. Also change
the hardcoded 0xBFFFFFFF value to ~NCQ_ABORT_ALL_FLAG as it ought to be.
Link: https://lore.kernel.org/r/20220220031810.738362-19-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3762d8f6ed ]
The declaration of the local variable destination1 in pm80xx_pci_mem_copy()
as a pointer to a u32 results in the sparse warning:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype]
got restricted __le32 [usertype]
Furthermore, the destination" argument of pm80xx_pci_mem_copy() is wrongly
declared with the const attribute.
Fix both problems by changing the type of the "destination" argument to
"__le32 *" and use this argument directly inside the pm80xx_pci_mem_copy()
function, thus removing the need for the destination1 local variable.
Link: https://lore.kernel.org/r/20220220031810.738362-6-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6736c3e1 ]
NCQ NON DATA is an NCQ command with the DMA_NONE DMA direction and so a
register-device-to-host-FIS response is expected for it.
However, for an IO_SUCCESS case, mpi_sata_completion() expects a
set-device-bits-FIS for any ata task with an use_ncq field true, which
includes NCQ NON DATA commands.
Fix this to correctly treat NCQ NON DATA commands as non-data by also
testing for the DMA_NONE DMA direction.
Link: https://lore.kernel.org/r/20220220031810.738362-16-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa028141ab ]
In the pm8001_chip_sata_req() and pm80xx_chip_sata_req() functions, all
tasks with a DMA direction of DMA_NONE (no data transfer) are initialized
using the ATAP value 0x04. However, NCQ NON DATA commands, while being
DMA_NONE commands are NCQ commands and need to be initialized using the
value 0x07 for ATAP, similarly to other NCQ commands.
Make sure that NCQ NON DATA command tasks are initialized similarly to
other NCQ commands by also testing the task "use_ncq" field in addition to
the DMA direction. While at it, reorganize the code into a chain of if -
else if - else to avoid useless affectations and debug messages.
Link: https://lore.kernel.org/r/20220220031810.738362-15-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6d0e3762 ]
Make sure that the __le32 fields of struct sata_cmd are manipulated after
applying the correct endian conversion. That is, use cpu_to_le32() for
assigning values and le32_to_cpu() for consulting a field value. In
particular, make sure that the calculations for the 4G boundary check are
done using CPU endianness and *not* little endian values. With these fixes,
many sparse warnings are removed.
While at it, fix some code identation and add blank lines after variable
declarations and in some other places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-12-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970404cc57 ]
Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8b12dfb47 ]
All fields of the kek_mgmt_req structure have the type __le32. So make sure
to use cpu_to_le32() to initialize them. This suppresses the sparse
warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] new_curidx_ksop
got int
Link: https://lore.kernel.org/r/20220220031810.738362-10-damien.lemoal@opensource.wdc.com
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca374f5d92 ]
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com
Fixes: a6cb3d012b ("[SCSI] pm80xx: thermal, sas controller config and error handling update")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb225b12db ]
The fields of the set_ctrl_cfg_req structure have the __le32 type, so use
cpu_to_le32() to assign them. This removes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32
got unsigned int
Link: https://lore.kernel.org/r/20220220031810.738362-8-damien.lemoal@opensource.wdc.com
Fixes: 842784e0d1 ("pm80xx: Update For Thermal Page Code")
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2268a180 ]
The ds_ads_m field of struct ssp_ini_tm_start_req has the type __le32.
Assigning a value to it should thus use cpu_to_le32(). This fixes the
sparse warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] ds_ads_m
got int
Link: https://lore.kernel.org/r/20220220031810.738362-7-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a37b6738b ]
Since the sata_cmd struct is zeroed out before its fields are initialized,
there is no need for using "|=" to initialize the ncqtag_atap_dir_m
field. Using a standard assignment removes the sparse warning:
warning: invalid assignment: |=
Also, since the ncqtag_atap_dir_m field has type __le32, use cpu_to_le32()
to generate the assigned value.
Link: https://lore.kernel.org/r/20220220031810.738362-5-damien.lemoal@opensource.wdc.com
Fixes: c6b9ef5779 ("[SCSI] pm80xx: NCQ error handling changes")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently a use-after-free may occur if a sas_task is aborted by the upper
layer before we handle the I/O completion in mpi_ssp_completion() or
mpi_sata_completion().
In this case, the following are the two steps in handling those I/O
completions:
- Call complete() to inform the upper layer handler of completion of
the I/O.
- Release driver resources associated with the sas_task in
pm8001_ccb_task_free() call.
When complete() is called, the upper layer may free the sas_task. As such,
we should not touch the associated sas_task afterwards, but we do so in the
pm8001_ccb_task_free() call.
Fix by swapping the complete() and pm8001_ccb_task_free() calls ordering.
Link: https://lore.kernel.org/r/1643289172-165636-4-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a use-after-free may occur if a TMF sas_task is aborted before we
handle the IO completion in mpi_ssp_completion(). The abort occurs due to
timeout.
When the timeout occurs, the SAS_TASK_STATE_ABORTED flag is set and the
sas_task is freed in pm8001_exec_internal_tmf_task().
However, if the I/O completion occurs later, the I/O completion still
thinks that the sas_task is available. Fix this by clearing the ccb->task
if the TMF times out - the I/O completion handler does nothing if this
pointer is cleared.
Link: https://lore.kernel.org/r/1643289172-165636-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
make W=1 complains of an undescribed function parameter:
drivers/scsi/pm8001/pm80xx_hwi.c:3938: warning: Function parameter or member 'circularQ' not described in 'process_one_iomb'
Fix it.
Link: https://lore.kernel.org/r/1643289172-165636-2-git-send-email-john.garry@huawei.com
Reported-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code handles completions for SATA devices in mpi_sata_completion()
and mpi_sata_event().
However, at the time when any SATA event happens, for almost all the event
types, the command is still in the target. It is therefore incorrect to
complete the task in sata_event().
There are some events for which we get sata_completions, some need recovery
procedure and others abort. All the tasks must be completed via
sata_completion() path.
Removed the task done related code from sata_events(). For tasks where we
don't get completions, let top layer call abort() to abort the command post
timeout.
Link: https://lore.kernel.org/r/20220124082255.86223-1-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Co-developed-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYetVgSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfElAQD/OZPx
dceTIXQixYGuHhGI3Il8O5ASYQVIU86gv+jRrgEA/MN4EWj4VsYaocrUdtTCBON1
wJYcC7VUekfNBX6KdeY=
=DcbH
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: nsp_cs: Check of ioremap return value
scsi: ufs: ufs-mediatek: Fix error checking in ufs_mtk_init_va09_pwr_ctrl()
scsi: ufs: Modify Tactive time setting conditions
scsi: efct: Remove useless DMA-32 fallback configuration
scsi: message: fusion: mptctl: Use dma_alloc_coherent()
scsi: message: fusion: mptsas: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mptsas_exp_repmanufacture_info()
scsi: message: fusion: mptbase: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mpt_alloc_fw_memory()
scsi: message: fusion: Remove usage of the deprecated "pci-dma-compat.h" API
scsi: megaraid: Avoid mismatched storage type sizes
scsi: hisi_sas: Remove unused variable and check in hisi_sas_send_ata_reset_each_phy()
scsi: aic79xx: Remove redundant error variable
scsi: pm80xx: Port reset timeout error handling correction
scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
scsi: mpi3mr: Fix some spelling mistakes
scsi: mpt3sas: Update persistent trigger pages from sysfs interface
scsi: core: Fix scsi_mode_select() interface
scsi: aacraid: Fix spelling of "its"
scsi: qedf: Fix potential dereference of NULL pointer
This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYeCJZyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfMnAQCsERG9
V4yX8LDpBjD7leIccf+6krJNNWaIWYYkEdxpzQD9FShB7/yDakFq3erW2y5mVqac
dZ065M0ckE4bxk9uMIE=
=gPHF
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (121 commits)
scsi: mpi3mr: Bump driver version to 8.0.0.61.0
scsi: mpi3mr: Fixes around reply request queues
scsi: mpi3mr: Enhanced Task Management Support Reply handling
scsi: mpi3mr: Use TM response codes from MPI3 headers
scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
scsi: mpi3mr: Print cable mngnt and temp threshold events
scsi: mpi3mr: Support Prepare for Reset event
scsi: mpi3mr: Add Event acknowledgment logic
scsi: mpi3mr: Gracefully handle online FW update operation
scsi: mpi3mr: Detect async reset that occurred in firmware
scsi: mpi3mr: Add IOC reinit function
scsi: mpi3mr: Handle offline FW activation in graceful manner
scsi: mpi3mr: Code refactor of IOC init - part2
scsi: mpi3mr: Code refactor of IOC init - part1
scsi: mpi3mr: Fault IOC when internal command gets timeout
scsi: mpi3mr: Display IOC firmware package version
scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
scsi: mpi3mr: Increase internal cmnds timeout to 60s
scsi: mpi3mr: Do access status validation before adding devices
scsi: mpi3mr: Add support for PCIe Managed Switch SES device
...
Error handling steps were not in sequence as per the programmers
manual. Expected sequence:
- PHY_DOWN (PORT_IN_RESET)
- PORT_RESET_TIMER_TMO
- Host aborts pending I/Os
- Host deregister the device
- Host sends HW_EVENT_PHY_DOWN ACK
Previously we were sending HW_EVENT_PHY_DOWN ACK first and then deregister
the device. Fix this to use the expected sequence.
Link: https://lore.kernel.org/r/20211228111753.10802-1-Ajish.Koshy@microchip.com
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull in the 5.16 fixes branch to resolve a conflict in the UFS driver
core.
Conflicts:
drivers/scsi/ufs/ufshcd.c
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver supports a "direct" mode of operation, where the SMP req frame
is directly copied into the command payload (and vice-versa for the SMP
resp).
To get at the SMP req frame data in the scatterlist the driver uses
phys_to_virt() on the DMA mapped memory dma_addr_t . This is broken, and
subsequently crashes as follows when an IOMMU is enabled:
Unable to handle kernel paging request at virtual address
ffff0000fcebfb00
...
pc : pm80xx_chip_smp_req+0x2d0/0x3d0
lr : pm80xx_chip_smp_req+0xac/0x3d0
pm80xx_chip_smp_req+0x2d0/0x3d0
pm8001_task_exec.constprop.0+0x368/0x520
pm8001_queue_command+0x1c/0x30
smp_execute_task_sg+0xdc/0x204
sas_discover_expander.part.0+0xac/0x6cc
sas_discover_root_expander+0x8c/0x150
sas_discover_domain+0x3ac/0x6a0
process_one_work+0x1d0/0x354
worker_thread+0x13c/0x470
kthread+0x17c/0x190
ret_from_fork+0x10/0x20
Code: 371806e1 910006d6 6b16033f 54000249 (38766b05)
---[ end trace b91d59aaee98ea2d ]---
note: kworker/u192:0[7] exited with preempt_count 1
Instead use kmap_atomic().
--
Difference to v1:
- use kmap_atomic() in both locations
Difference to v2:
- add whitespace around arithmetic (Damien)
Link: https://lore.kernel.org/r/1639390248-213603-1-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following kernel-doc warnings:
drivers/scsi/pm8001/pm8001_ctl.c:900: warning: cannot understand function prototype: 'const char *const mpiStateText[] = '
drivers/scsi/pm8001/pm8001_ctl.c:930: warning: Function parameter or member 'attr' not described in 'ctl_hmi_error_show'
drivers/scsi/pm8001/pm8001_ctl.c:951: warning: Function parameter or member 'attr' not described in 'ctl_raae_count_show'
drivers/scsi/pm8001/pm8001_ctl.c:972: warning: Function parameter or member 'attr' not described in 'ctl_iop0_count_show'
drivers/scsi/pm8001/pm8001_ctl.c:993: warning: Function parameter or member 'attr' not described in 'ctl_iop1_count_show'
Link: https://lore.kernel.org/r/20211129194609.3466071-11-bvanassche@acm.org
Fixes: 4ddbea1b6f ("scsi: pm80xx: Add sysfs attribute to check MPI state")
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pm8001_mpi_build_cmd() prepares and sends all commands to a controller.
Having pm80xx_mpi_build_cmd tracepoint can help us with latency issues.
this patch depends on patch "scsi: pm80xx: Add tracepoints".
Link: https://lore.kernel.org/r/20211115215750.131696-3-changyuanl@google.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Co-developed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tracepoints for tracking controller and ATA commands issued and completed.
Link: https://lore.kernel.org/r/20211115215750.131696-2-changyuanl@google.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Co-developed-by: Akshat Jain <akshatzen@google.com>
Signed-off-by: Akshat Jain <akshatzen@google.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We used to allocate X bytes while we only need X bits.
Link: https://lore.kernel.org/r/20211101232825.2350233-5-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting from commit 05c6c029a4 ("scsi: pm80xx: Increase number of
supported queues") driver initializes only max_q_num queues. Do not use an
invalid queue if the WARN_ON condition is true.
Link: https://lore.kernel.org/r/20211101232825.2350233-4-ipylypiv@google.com
Fixes: 7640e1eb8c ("scsi: pm80xx: Make mpi_build_cmd locking consistent")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Address-of operator cannot return NULL.
Link: https://lore.kernel.org/r/20211101232825.2350233-3-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Phy ID is located in the least significant byte of the 4-byte field.
mpi_phy_stop_resp() already applies such mask.
Link: https://lore.kernel.org/r/20211101232825.2350233-2-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct device supports attribute groups directly but does not support
struct device_attribute directly. Hence switch to attribute groups.
Link: https://lore.kernel.org/r/20211012233558.4066756-36-bvanassche@acm.org
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pm8001_mpi_get_nvmd_resp() handles a GET_NVMD_DATA response, not a
SET_NVMD_DATA response, as the log statement implies.
Fixes: 1f889b5871 ("scsi: pm80xx: Fix pm8001_mpi_get_nvmd_resp() race condition")
Link: https://lore.kernel.org/r/20210929025847.646999-1-ipylypiv@google.com
Reviewed-by: Changyuan Lyu <changyuanl@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a follow up cleanup to the commit 924a3541ea ("scsi: libsas:
aic94xx: hisi_sas: mvsas: pm8001: Use dev_is_expander()")
Link: https://lore.kernel.org/r/20210929025807.646589-1-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver failed to release all memory allocated. This would lead to memory
leak during driver removal.
Properly free memory when the module is removed.
Link: https://lore.kernel.org/r/20210906170404.5682-5-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct inbound queue and outbound queue size in 'ib_log' and 'ob_log'
sysfs entries.
Link: https://lore.kernel.org/r/20210906170404.5682-4-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1f02beff22 ("scsi: pm80xx: Remove global lock from outbound queue
processing") introduced a lock per outbound queue. Prior to that change the
driver was using a global lock for all outbound queues.
While processing the I/O responses and events the driver takes the outbound
queue spinlock and is supposed to release it in pm8001_ccb_task_free_done()
before calling command done(). Since the older code was using a global
lock, pm8001_ccb_task_free_done() was releasing the global spin lock. The
change that split the lock per outbound queue did not consider this and
pm8001_ccb_task_free_done() was still releasing the global lock.
Link: https://lore.kernel.org/r/20210906170404.5682-3-Ajish.Koshy@microchip.com
Fixes: 1f02beff22 ("scsi: pm80xx: Remove global lock from outbound queue processing")
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During phyup event, the firmware provides the phy_id and port_id and driver
is supposed to use these during device handle registration. Previously the
driver was using the port id value from libsas during device handle
registration. Since id can be different from the one assigned by firmware,
this can lead to wrong device registration and drives not showing up.
Use firmware assigned port id during device registration.
Link: https://lore.kernel.org/r/20210906170404.5682-2-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable 'rv' is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210804143319.115340-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
The TMF timeout timer may trigger at the same time when the response from a
controller is being handled. When this happens the SAS task may get freed
before the response processing is finished.
Fix this by calling complete() only when SAS_TASK_STATE_DONE is not set.
A similar race condition was fixed in commit b90cd6f2b9 ("scsi: libsas:
fix a race condition when smp task timeout")
Link: https://lore.kernel.org/r/20210707185945.35559-1-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel-doc warnings then test again, wash, rinse, find more, then
repeat more/again.
Also fix spellos, some grammar, and some punctuation.
../drivers/scsi/pm8001/pm8001_ctl.c:557: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** pm8001_ctl_fatal_log_show - fatal error logging
../drivers/scsi/pm8001/pm8001_ctl.c:577: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** non_fatal_log_show - non fatal error logging
../drivers/scsi/pm8001/pm8001_ctl.c:622: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** pm8001_ctl_gsm_log_show - gsm dump collection
Link: https://lore.kernel.org/r/20210708165723.8594-1-rdunlap@infradead.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor fixes and clean ups in the core and various
drivers. The only core change in behaviour is the I/O retry for
spinup notify, but that shouldn't impact anything other than the
failing case.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYOqWWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYBtAQCpqVdl
Axi1SpD6/UuKOgRmboWscoKD8FLHwvLDMRyCRQEAnLu3XdB9HcQrwZOkTG14vrfB
q2XB5cP4XAITxFLN1qo=
=9AO9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes and clean ups in the core and various
drivers.
The only core change in behaviour is the I/O retry for spinup notify,
but that shouldn't impact anything other than the failing case"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
scsi: virtio_scsi: Add validation for residual bytes from response
scsi: ipr: System crashes when seeing type 20 error
scsi: core: Retry I/O for Notify (Enable Spinup) Required error
scsi: mpi3mr: Fix warnings reported by smatch
scsi: qedf: Add check to synchronize abort and flush
scsi: MAINTAINERS: Add mpi3mr driver maintainers
scsi: libfc: Fix array index out of bound exception
scsi: mvsas: Use DEVICE_ATTR_RO()/RW() macro
scsi: megaraid_mbox: Use DEVICE_ATTR_ADMIN_RO() macro
scsi: qedf: Use DEVICE_ATTR_RO() macro
scsi: qedi: Use DEVICE_ATTR_RO() macro
scsi: message: mptfc: Switch from pci_ to dma_ API
scsi: be2iscsi: Fix some missing space in some messages
scsi: be2iscsi: Fix an error handling path in beiscsi_dev_probe()
scsi: ufs: Fix build warning without CONFIG_PM
scsi: bnx2fc: Remove meaningless bnx2fc_abts_cleanup() return value assignment
scsi: qla2xxx: Add heartbeat check
scsi: virtio_scsi: Do not overwrite SCSI status
scsi: libsas: Add LUN number check in .slave_alloc callback
scsi: core: Inline scsi_mq_alloc_queue()
...
This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers. The major core change is a rework
to drop the status byte handling macros and the old bit shifted
definitions and the rest of the updates are minor fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYN7I6iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXpRAQCkngYZ
35yQrqOxgOk2pfrysE95tHrV1MfJm2U49NFTwAEAuZutEvBUTfBF+sbcJ06r6q7i
H0hkJN/Io7enFs5v3WA=
=zwIa
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers.
The major core change is a rework to drop the status byte handling
macros and the old bit shifted definitions and the rest of the updates
are minor fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (287 commits)
scsi: aha1740: Avoid over-read of sense buffer
scsi: arcmsr: Avoid over-read of sense buffer
scsi: ips: Avoid over-read of sense buffer
scsi: ufs: ufs-mediatek: Add missing of_node_put() in ufs_mtk_probe()
scsi: elx: libefc: Fix IRQ restore in efc_domain_dispatch_frame()
scsi: elx: libefc: Fix less than zero comparison of a unsigned int
scsi: elx: efct: Fix pointer error checking in debugfs init
scsi: elx: efct: Fix is_originator return code type
scsi: elx: efct: Fix link error for _bad_cmpxchg
scsi: elx: efct: Eliminate unnecessary boolean check in efct_hw_command_cancel()
scsi: elx: efct: Do not use id uninitialized in efct_lio_setup_session()
scsi: elx: efct: Fix error handling in efct_hw_init()
scsi: elx: efct: Remove redundant initialization of variable lun
scsi: elx: efct: Fix spelling mistake "Unexected" -> "Unexpected"
scsi: lpfc: Fix build error in lpfc_scsi.c
scsi: target: iscsi: Remove redundant continue statement
scsi: qla4xxx: Remove redundant continue statement
scsi: ppa: Switch to use module_parport_driver()
scsi: imm: Switch to use module_parport_driver()
scsi: mpt3sas: Fix error return value in _scsih_expander_add()
...
Offlining a SATA device connected to a hisi SAS controller and then
scanning the host will result in detecting 255 non-existent devices:
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:2:0] disk SEAGATE ST600MM0006 B001 /dev/sdc
# echo "offline" > /sys/block/sdb/device/state
# echo "- - -" > /sys/class/scsi_host/host2/scan
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:1:1] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdh
...
[2:0:1:255] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdjb
After a REPORT LUN command issued to the offline device fails, the SCSI
midlayer tries to do a sequential scan of all devices whose LUN number is
not 0. However, SATA does not support LUN numbers at all.
Introduce a generic sas_slave_alloc() handler which will return -ENXIO for
SATA devices if the requested LUN number is larger than 0 and make libsas
drivers use this function as their .slave_alloc callback.
Link: https://lore.kernel.org/r/20210622034037.1467088-1-yuyufen@huawei.com
Reported-by: Wu Bo <wubo40@huawei.com>
Suggested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
