Bitwise operation is a little faster.
So I replace after() with using the flag FLAG_SND_UNA_ADVANCED as it is
already set before.
In addtion, there's another similar improvement in tcp_cwnd_reduction().
Cc: Joe Perches <joe@perches.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
net: dsa: mv88e6xxx: Support more SERDES interfacxes
Currently the SERDES interfaces for ports 9 and 10 on the mv88e6390x
are supported, allowing upto 10G. However, when unused, these SERDES
interfaces can be used by some of the lower ports for 1000Base-X.
The tricky bit here is ordering. The SERDES have to become free from
ports 9 or 10 before they can be used with lower ports. Normally, this
would happen only when these ports would be configured up, which is
too late. So at probe time, defaulting ports 9 and 10 to 1000BaseX
frees them for use with lower ports. If they are actually needed, they
will be taken back when port 9 and 10 goes up.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
net: phy: convert advertise and supported to linkmode
This is the last part in converting phylib to make use of a linux
bitmap, not a u32, to represent links modes. This will allow support
for PHYs > 1Gbps, which need to use link modes represented by a bit >
32.
A number of MAC and PHY drivers need changes to support this. However
the previous two patchesets reduced the number somewhat, the helpers
which were introduced have been modified instead of the actual
drivers.
The follow on patches then make use of the extra bits, adding support
for more link modes.
Given how invasive this change is, i expect the build is broken for
some architectures i did not test. I will fixup the breakage as fast
as i can.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snmp_counter.rst explains the meanings of snmp counters. It also
provides a set of experiments (only 1 for this initial patch),
combines the experiments' resutls and the snmp counters'
meanings. This is an initial path, only explains a part of IP/ICMP
counters and provide a simple ping test.
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the broadcast retransmission algorithm is using the
'prev_retr' field in struct tipc_link to time stamp the latest broadcast
retransmission occasion. This helps to restrict retransmission of
individual broadcast packets to max once per 10 milliseconds, even
though all other criteria for retransmission are met.
We now move this time stamp to the control block of each individual
packet, and remove other limiting criteria. This simplifies the
retransmission algorithm, and eliminates any risk of logical errors
in selecting which packets can be retransmitted.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: sched: indirect tc block cb registration
John says:
This patchset introduces an alternative to egdev offload by allowing a
driver to register for block updates when an external device (e.g. tunnel
netdev) is bound to a TC block. Drivers can track new netdevs or register
to existing ones to receive information on such events. Based on this,
they may register for block offload rules using already existing
functions.
The patchset also implements this new indirect block registration in the
NFP driver to allow the offloading of tunnel rules. The use of egdev
offload (which is currently only used for tunnel offload) is subsequently
removed.
RFC v2 -> PATCH
- removed embedded tracking function from indir block register (now up to
driver to clean up after itself)
- refactored NFP code due to recent submissions
- removed priv list clean function in NFP (list should be cleared by
indirect block unregisters)
RFC v1->v2:
- free allocated owner struct in block_owner_clean function
- add geneve type helper function
- move test stub in NFP (v1 patch 2) to full tunnel offload
implementation via indirect blocks (v2 patches 3-8)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to NFP mean that stats updates from fw to driver no longer
require a flow lookup and (because egdev offload has been removed) the
ingress netdev for a lookup is now always known.
Remove obsolete code in a flow lookup that matches on host context and
that allows for a netdev to be NULL.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, only tunnel decap rules required egdev registration for
offload in NFP. These are now supported via indirect TC block callbacks.
Remove the egdev code from NFP.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, TC block tunnel decap rules were only offloaded when a
callback was triggered through registration of the rules egress device.
This meant that the driver had no access to the ingress netdev and so
could not verify it was the same tunnel type that the rule implied.
Register tunnel devices for indirect TC block offloads in NFP, giving
access to new rules based on the ingress device rather than egress. Use
this to verify the netdev type of VXLAN and Geneve based rules and offload
the rules to HW if applicable.
Tunnel registration is done via a netdev notifier. On notifier
registration, this is triggered for already existing netdevs. This means
that NFP can register for offloads from devices that exist before it is
loaded (filter rules will be replayed from the TC core). Similarly, on
notifier unregister, a call is triggered for each currently active netdev.
This allows the driver to unregister any indirect block callbacks that may
still be active.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the actions and tunnel_conf files contain local functions that check
the type of an input netdev. In preparation for re-use with tunnel offload
via indirect blocks, move these to static inline functions in a header
file.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the offload functions in NFP assumed that the ingress (or
egress) netdev passed to them was an nfp repr.
Modify the driver to permit the passing of non repr netdevs as the ingress
device for an offload rule candidate. This may include devices such as
tunnels. The driver should then base its offload decision on a combination
of ingress device and egress port for a rule.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers can register to receive TC block bind/unbind callbacks
by implementing the setup_tc ndo in any of their given netdevs. However,
drivers may also be interested in binds to higher level devices (e.g.
tunnel drivers) to potentially offload filters applied to them.
Introduce indirect block devs which allows drivers to register callbacks
for block binds on other devices. The callback is triggered when the
device is bound to a block, allowing the driver to register for rules
applied to that block using already available functions.
Freeing an indirect block callback will trigger an unbind event (if
necessary) to direct the driver to remove any offloaded rules and unreg
any block rule callbacks. It is the responsibility of the implementing
driver to clean any registered indirect block callbacks before exiting,
if the block it still active at such a time.
Allow registering an indirect block dev callback for a device that is
already bound to a block. In this case (if it is an ingress block),
register and also trigger the callback meaning that any already installed
rules can be replayed to the calling driver.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: add macros for PHYID matching in PHY driver config
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Use them initially in the Realtek PHY drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: further phylib simplifications after recent changes to the state machine
After the recent changes to the state machine phylib can be further
simplified (w/o having to make any assumptions).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
This allows to remove this flag from all driver configs.
v2:
- add helper for check in patch 1
- remove PHY_HAS_INTERRUPT from all drivers, not only Realtek
- remove flag PHY_HAS_INTERRUPT completely
v3:
- rebase patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same change as made to sctp_intl_store_reasm().
To be fully correct, an iterator has an undefined value when something
like skb_queue_walk() naturally terminates.
This will actually matter when SKB queues are converted over to
list_head.
Formalize what this code ends up doing with the current
implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
To be fully correct, an iterator has an undefined value when something
like skb_queue_walk() naturally terminates.
This will actually matter when SKB queues are converted over to
list_head.
Formalize what this code ends up doing with the current
implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate the assumption that SKBs and SKB list heads can
be cast to eachother in SKB list handling code.
This change also appears to fix a bug since the list->next pointer is
sampled outside of holding the SKB queue lock.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of direct SKB list pointer accesses.
The loops in this function had to be rewritten to accommodate this
more easily.
The first loop iterates now over the target list in the outer loop,
and triggers an mmc data operation when the per-operation limits are
hit.
Then after the loops, if we have any residue, we trigger the last
and final operation.
For the page aligned workaround, where we have to copy the read data
back into the original list of SKBs, we use a two-tiered loop. The
outer loop stays the same and iterates over pktlist, and then we have
an inner loop which uses skb_peek_next(). The break logic has been
simplified because we know that the aggregate length of the SKBs in
the source and destination lists are the same.
This change also ends up fixing a bug, having to do with the
maintainance of the seg_sz variable and how it drove the outermost
loop. It begins as:
seg_sz = target_list->qlen;
ie. the number of packets in the target_list queue. The loop
structure was then:
while (seq_sz) {
...
while (not at end of target_list) {
...
sg_cnt++
...
}
...
seg_sz -= sg_cnt;
The assumption built into that last statement is that sg_cnt counts
how many packets from target_list have been fully processed by the
inner loop. But this not true.
If we hit one of the limits, such as the max segment size or the max
request size, we will break and copy a partial packet then contine
back up to the top of the outermost loop.
With the new loops we don't have this problem as we don't guard the
loop exit with a packet count, but instead use the progression of the
pkt_next SKB through the list to the end. The general structure is:
sg_cnt = 0;
skb_queue_walk(target_list, pkt_next) {
pkt_offset = 0;
...
sg_cnt++;
...
while (pkt_offset < pkt_next->len) {
pkt_offset += sg_data_size;
if (queued up max per request)
mmc_submit_one();
}
}
if (sg_cnt)
mmc_submit_one();
The variables that maintain where we are in the MMC command state such
as req_sz, sg_cnt, and sgl are reset when we emit one of these full
sized requests.
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out I missed one VLAN_TAG_PRESENT in OVS code while rebasing.
This fixes it.
Fixes: 9df46aefaf ("OVS: remove use of VLAN_TAG_PRESENT")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following:
skb = skb->next;
...
if (skb == (struct sk_buff *)queue)
is transformed into:
skb = skb_peek_next(skb, queue);
...
if (!skb)
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei says:
====================
dpaa2-eth: defer probe on object allocate
Allocatable objects on the fsl-mc bus may be probed by the fsl_mc_allocator
after the first attempts of other drivers to use them. Defer the probe when
this situation happens.
Changes in v2:
- proper handling of IS_ERR_OR_NULL
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl_mc_portal_allocate can fail when the requested MC portals are
not yet probed by the fsl_mc_allocator. In this situation, the driver
should defer the probe.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl_mc_object_allocate function can fail because not all allocatable
objects are probed by the fsl_mc_allocator at the call time. Defer the
dpaa2-eth probe when this happens.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the udp6 code path, we needed multiple tests to select the correct
mib to be updated. Since we touch at least a counter at each iteration,
it's convenient to use the recently introduced __UDPX_MIB() helper once
and remove some code duplication.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__netdev_tx_sent_queue() was added in commit e59020abf0f
("net: bql: add __netdev_tx_sent_queue()") and allows for
better GSO performance.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miroslav Lichvar says:
====================
More accurate PHC<->system clock synchronization
RFC->v1:
- added new patches
- separated PHC timestamp from ptp_system_timestamp
- fixed memory leak in PTP_SYS_OFFSET_EXTENDED
- changed PTP_SYS_OFFSET_EXTENDED to work with array of arrays
- fixed PTP_SYS_OFFSET_EXTENDED to break correctly from loop
- fixed timecounter updates in drivers
- split gettimex in igb driver
- fixed ptp_read_* functions to be available without
CONFIG_PTP_1588_CLOCK
This series enables a more accurate synchronization between PTP hardware
clocks and the system clock.
The first two patches are minor cleanup/bug fixes.
The third patch adds an extended version of the PTP_SYS_OFFSET ioctl,
which returns three timestamps for each measurement. The idea is to
shorten the interval between the system timestamps to contain just the
reading of the lowest register of the PHC in order to reduce the error
in the measured offset and get a smaller upper bound on the maximum
error.
The fourth patch deprecates the original gettime function.
The remaining patches update the gettime function in order to support
the new ioctl in the e1000e, igb, ixgbe, and tg3 drivers.
Tests with few different NICs in different machines show that:
- with an I219 (e1000e) the measured delay was reduced from 2500 to 1300
ns and the error in the measured offset, when compared to the cross
timestamping supported by the driver, was reduced by a factor of 5
- with an I210 (igb) the delay was reduced from 5100 to 1700 ns
- with an I350 (igb) the delay was reduced from 2300 to 750 ns
- with an X550 (ixgbe) the delay was reduced from 1950 to 650 ns
- with a BCM5720 (tg3) the delay was reduced from 2400 to 1200 ns
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
