On the i.MX6SX, it is common to use the LDB and LCDIF with the same
parent clock, such as the IMX6SX_CLK_PLL5_VIDEO_DIV, for example.
Due to the CLK_SET_RATE_PARENT flag, the LDB clock would try to set the
clock parent rate, which can mess with the required clock rate calculated
from the eLCDIF driver.
To prevent this problem, remove the CLK_SET_RATE_PARENT flag from the
LDB clocks, so that a correct clock relationship can be achieved.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230416150004.16834-1-festevam@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The clk count has been get with of_clk_get_parent_count, there is
no need to pass clk_count from users.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230104110032.1220721-4-peng.fan@oss.nxp.com
The imx_obtain_fixed_clk_hw name was wrong and misleading. Renaming it
to imx_get_clk_hw_by_name clarifies the purpose of the function, and
will allow it to be used not only for fixed rate clocks but also in
wider contexts.
No functional changes intended.
The replacements were made with the following command:
grep -rl 'imx_obtain_fixed_clk_hw' ./ | \
xargs sed -i 's/imx_obtain_fixed_clk_hw/imx_get_clk_hw_by_name/g'
Tested on a BSH SystemMaster (SMM) S2 board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221113180839.1625832-1-dario.binacchi@amarulasolutions.com
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e3 ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com
Tested-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
Without this we were getting errors like:
In file included from drivers/clk/clkdev.c:22:0:
drivers/clk/clk.h:36:23: error: static declaration of '__clk_get_hw' follows non-static declaration
include/linux/clk-provider.h:808:16: note: previous declaration of '__clk_get_hw' was here
Fixes: 59fcdce425 ("clk: Remove ifdef for COMMON_CLK in clk-provider.h")
fixes: 73e0e496af ("clkdev: Always allocate a struct clk and call __clk_get() w/ CCF")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Switch the entire clk-imx6sx driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock IMX6SX_CLK_AXI is not registered at all.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MMDC_P1_IPG clock need to be on always on to make sure
the MMDC register can be accessed successfully.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx_mmdc_mask_handshake() API instead of programming CCM
register directly in each platform to mask unused MMDC channel's
handshake.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: d551356890 ("ARM: imx: add clock driver for imx6sx")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, and its clock gate in CCM CCGR1 CG14
needs to be enabled before access, add it to
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Disable those unnecessary clocks during kernel boot up to save power,
those modules clock should be managed by modules driver in runtime.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has lvds2 (analog clock2), an I/O clock like lvds1.
And this lvds2, along with lvds1, can be used to provide
external clock source to the internal pll, such as pll4_audio
and pll5_video.
This patch mainly adds the lvds2 to the clock tree and fix its
relationship with pll accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_div_table are not supposed to change at runtime. All functions
working with clk_div_table provided by <linux/clk-provider.h> work
with const clk_div_table. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pllx_bypass_src mux shouldn't be the parent of pllx clock
since it's only valid when when pllx BYPASS bit is set.
Thus it is actually one parent of pllx_bypass only.
Instead, pllx parent should be fixed to osc according to
reference manual.
Other plls have the same issue.
e.g. before fix, the pll tree is:
osc 6 6 24000000 0 0
pll1_bypass_src 0 0 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
After the fix, it's:
osc 6 6 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SAIx and SAIx_IPG share the same bit fields in the CCM registers, so
we should better register them via imx_clk_gate2_shared().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.
We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.
So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
2015-06-03 14:44:33 +08:00
Renamed from arch/arm/mach-imx/clk-imx6sx.c (Browse further)