The power-mode sequence on MMC is MMC_POWER_OFF -> MMC_POWER_UP ->
MMC_POWER_ON and not MMC_POWER_ON -> MMC_POWER_UP, as the driver currently
is implying.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO IRQs got unmasked on sh-mobile while writing to the
CTL_CLK_AND_WAIT_CTL register, because that register at address 0x138
is not implemented on those SoCs and writes to it overwrite the
register at address 0x38: CTL_SDIO_IRQ_MASK. Previous patches
eliminated access to register above 0xff on sh-mobile, so that this
work-around isn't needed anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHI registers occupy only a 0x100 byte large window, not 0x200 byte.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHI registers occupy only a 0x100 byte large window, not 0x200 byte.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all tmio implementations have registers above oxff. Accessing
them on thise platforms is dangerous. In some cases it leads to
address wrapping to addresses below 0x100, which corrupts random
unrelated registers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The CONFIG_MFD_SH_MOBILE_SDHI Kconfig symbol is going to disappear soon,
switch ecovec to using CONFIG_MMC_TMIO(_MODULE).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
TMIO MMC chips contain an SD / SDIO IP core from Panasonic, similar to
the one, used in MN5774 and other MN57xx controllers. These IP cores are
included in many multifunction devices, in sh-mobile chips from Renesas,
in the latter case they can also use DMA. Some sh-mobile implementations
also have some other specialities, that MFD-based solutions don't have.
This makes supporting all these features in a monolithic driver inconveniet
and error-prone. This patch splits the driver into 3 parts: the core,
the MFD glue and the DMA support. In case of a modular build, two modules
will be built: mmc_tmio_core and mmc_tmio.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows transferring of some requests in PIO and some in DMA
mode and defaults to using DMA only for transfers longer than 8 bytes.
This is especially useful with SDIO, which can have lots of 2- and 4-byte
transfers, creating unnecessary high overhead, when executed in DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SDHI tmio implementations the order of DMA and command completion
interrupts swaps, which leads to malfunction. This patch postpones
DMA activation until the MMC command completion IRQ time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based on the commit "af51715079e7fb6b290e1881d63d815dc4de5011":
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
The driver may invalidate the mmc_card->csd when host driver uses dma.
So this subroutine also needs a kmalloc buffer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK read in
SDIO on imx53.
The CMDTYPE of the CMD register (offset 0xE) should be set to "11"
when the STOP CMD12 is issued on imx53 to abort one open ended
multi-blk IO. Otherwise the TC INT wouldn't be generated.
In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the transfer
and remains on hold if the abort command is not sent on imx53.
As a result, the TC flag is not asserted and SW receives timeout
exception. Set bit1 of Vendor Spec register to fix it.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add one flag to indicate the GPIO CD/WP is enabled or not
on imx platforms, and reuse the writel/readl as the general
APIs for imx SOCs.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add the abort CMDTYPE bits definition of command register (offset 0xE)
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since these are the headers that provide irq_of_parse_and_map()
and NO_IRQ.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).
Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHCI driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it was not converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision). The newer VIA
driver has similar code too. This patch converts both drivers to use
the 'revision' field of 'struct pci_dev'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
drivers/mmc/card/mmc_test.c: In function ‘mmc_test_seq_perf’:
drivers/mmc/card/mmc_test.c:1878:28: warning: variable ‘ts’ set but not
used [-Wunused-but-set-variable]
There's no reason to be calling timespec_sub() here, because
mmc_test_print_avg_rate() is going to do that itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: simplify iget & friends
fs: pull inode->i_lock up out of writeback_single_inode
fs: rename inode_lock to inode_hash_lock
fs: move i_wb_list out from under inode_lock
fs: move i_sb_list out from under inode_lock
fs: remove inode_lock from iput_final and prune_icache
fs: Lock the inode LRU list separately
fs: factor inode disposal
fs: protect inode->i_state with inode->i_lock
autofs4: Do not potentially dereference NULL pointer returned by fget() in autofs_dev_ioctl_setpipefd()
autofs4 - remove autofs4_lock
autofs4 - fix d_manage() return on rcu-walk
autofs4 - fix autofs4_expire_indirect() traversal
autofs4 - fix dentry leak in autofs4_expire_direct()
autofs4 - reinstate last used update on access
vfs - check non-mountpoint dentry might block in __follow_mount_rcu()
Fix the following compile failure:
drivers/media/rc/ite-cir.c: In function 'ite_decode_bytes':
drivers/media/rc/ite-cir.c:190: error: implicit declaration of function 'generic_find_next_le_bit'
drivers/media/rc/ite-cir.c:199: error: implicit declaration of function 'generic_find_next_zero_le_bit'
Caused by commit 620a32bba4 ("[media] rc: New rc-based ite-cir driver
for several ITE CIRs") interacting with commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge get_new_inode/get_new_inode_fast into iget5_locked/iget_locked
as those were the only callers. Remove the internal ifind/ifind_fast
helpers - ifind_fast only had a single caller, and ifind had two
callers wanting it to do different things. Also clean up the comments
in this area to focus on information important to a developer trying
to use it, instead of overloading them with implementation details.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
First thing we do in writeback_single_inode() is take the i_lock and
the last thing we do is drop it. A caller already holds the i_lock,
so pull the i_lock out of writeback_single_inode() to reduce the
round trips on this lock during inode writeback.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All that remains of the inode_lock is protecting the inode hash list
manipulation and traversals. Rename the inode_lock to
inode_hash_lock to reflect it's actual function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect the inode writeback list with a new global lock
inode_wb_list_lock and use it to protect the list manipulations and
traversals. This lock replaces the inode_lock as the inodes on the
list can be validity checked while holding the inode->i_lock and
hence the inode_lock is no longer needed to protect the list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect the per-sb inode list with a new global lock
inode_sb_list_lock and use it to protect the list manipulations and
traversals. This lock replaces the inode_lock as the inodes on the
list can be validity checked while holding the inode->i_lock and
hence the inode_lock is no longer needed to protect the list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that inode state changes are protected by the inode->i_lock and
the inode LRU manipulations by the inode_lru_lock, we can remove the
inode_lock from prune_icache and the initial part of iput_final().
instead of using the inode_lock to protect the inode during
iput_final, use the inode->i_lock instead. This protects the inode
against new references being taken while we change the inode state
to I_FREEING, as well as preventing prune_icache from grabbing the
inode while we are manipulating it. Hence we no longer need the
inode_lock in iput_final prior to setting I_FREEING on the inode.
For prune_icache, we no longer need the inode_lock to protect the
LRU list, and the inodes themselves are protected against freeing
races by the inode->i_lock. Hence we can lift the inode_lock from
prune_icache as well.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduce the inode_lru_lock to protect the inode_lru list. This
lock is nested inside the inode->i_lock to allow the inode to be
added to the LRU list in iput_final without needing to deal with
lock inversions. This keeps iput_final() clean and neat.
Further, where marking the inode I_FREEING and removing it from the
LRU, move the LRU list manipulation within the inode->i_lock to keep
the list manipulation consistent with iput_final. This also means
that most of the open coded LRU list removal + unused inode
accounting can now use the inode_lru_list_del() wrappers which
cleans the code up further.
However, this locking change means what the LRU traversal in
prune_icache() inverts this lock ordering and needs to use trylock
semantics on the inode->i_lock to avoid deadlocking. In these cases,
if we fail to lock the inode we move it to the back of the LRU to
prevent spinning on it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We have a couple of places that dispose of inodes. factor the
disposal into evict() to isolate this code and make it simpler to
peel away the inode_lock from the code.
While doing this, change the logic flow in iput_final() to separate
the different cases that need to be handled to make the transitions
the inode goes through more obvious.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect inode state transitions and validity checks with the
inode->i_lock. This enables us to make inode state transitions
independently of the inode_lock and is the first step to peeling
away the inode_lock from the code.
This requires that __iget() is done atomically with i_state checks
during list traversals so that we don't race with another thread
marking the inode I_FREEING between the state check and grabbing the
reference.
Also remove the unlock_new_inode() memory barrier optimisation
required to avoid taking the inode_lock when clearing I_NEW.
Simplify the code by simply taking the inode->i_lock around the
state change and wakeup. Because the wakeup is no longer tricky,
remove the wake_up_inode() function and open code the wakeup where
necessary.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
SLUB: Write to per cpu data when allocating it
slub: Fix debugobjects with lockless fastpath
Commit ddd588b5dd ("oom: suppress nodes that are not allowed from
meminfo on oom kill") moved lib/show_mem.o out of lib/lib.a, which
resulted in build warnings on all architectures that implement their own
versions of show_mem():
lib/lib.a(show_mem.o): In function `show_mem':
show_mem.c:(.text+0x1f4): multiple definition of `show_mem'
arch/sparc/mm/built-in.o:(.text+0xd70): first defined here
The fix is to remove __show_mem() and add its argument to show_mem() in
all implementations to prevent this breakage.
Architectures that implement their own show_mem() actually don't do
anything with the argument yet, but they could be made to filter nodes
that aren't allowed in the current context in the future just like the
generic implementation.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vblank: update recently added vbl interface to be more future proof.
drm radeon: Return -EINVAL on wrong pm sysfs access
drm/radeon/kms: fix hardcoded EDID handling
Revert "drm/i915: Don't save/restore hardware status page address register"
drm/i915: Avoid unmapping pages from a NULL address space
drm/i915: Fix use after free within tracepoint
drm/i915: Restore missing command flush before interrupt on BLT ring
drm/i915: Disable pagefaults along execbuffer relocation fast path
drm/i915: Fix computation of pitch for dumb bo creator
drm/i915: report correct render clock frequencies on SNB
drm/i915/dp: Correct the order of deletion for ghost eDP devices
drm/i915: Fix tiling corruption from pipelined fencing
drm/i915: Re-enable self-refresh
drm/i915: Prevent racy removal of request from client list
drm/i915: skip redundant operations whilst enabling pipes and planes
drm/i915: Remove surplus POSTING_READs before wait_for_vblank
drm/radeon/kms: prefer legacy pll algo for tv-out
drm: check for modesetting on modeset ioctls
drm/kernel: vblank wait on crtc > 1
drm: Fix use-after-free in drm_gem_vm_close()
It turns out that the cmpxchg16b emulation has to access vmalloced
percpu memory with interrupts disabled. If the memory has never
been touched before then the fault necessary to establish the
mapping will not to occur and the kernel will fail on boot.
Fix that by reusing the CONFIG_PREEMPT code that writes the
cpu number into a field on every cpu. Writing to the per cpu
area before causes the mapping to be established before we get
to a cmpxchg16b emulation.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
On Thu, 24 Mar 2011, Ingo Molnar wrote:
> RIP: 0010:[<ffffffff810570a9>] [<ffffffff810570a9>] get_next_timer_interrupt+0x119/0x260
That's a typical timer crash, but you were unable to debug it with
debugobjects because commit d3f661d6 broke those.
Cc: Christoph Lameter <cl@linux.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
In fs/autofs4/dev-ioctl.c::autofs_dev_ioctl_setpipefd() we call fget(),
which may return NULL, but we do not explicitly test for that NULL return
so we may end up dereferencing a NULL pointer - bad.
When I originally submitted this patch I had chosen EBUSY as the return
value to use if this happens. Ian Kent was kind enough to explain why that
would most likely be wrong and why EBADF should most likely be used
instead. This version of the patch uses EBADF.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The autofs4_lock introduced by the rcu-walk changes has unnecessarily
broad scope. The locking is better handled by the per-autofs super
block lookup_lock.
Signed-off-by: Ian Kent <raven@themaw.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The daemon never needs to block and, in the rcu-walk case an error
return isn't used, so always return zero.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The vfs-scale changes changed the traversal used in
autofs4_expire_indirect() from a list to a depth first tree traversal
which isn't right.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is a missing dput() when returning from autofs4_expire_direct()
when we see that the dentry is already a pending mount.
Signed-off-by: Ian Kent <raven@themaw.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When direct (and offset) mounts were introduced the the last used
timeout could no longer be updated in ->d_revalidate(). This is
because covered direct mounts would be followed over without calling
the autofs file system. As a result the definition of the busyness
check for all entries was changed to be "actually busy" being an open
file or working directory within the automount. But now we have a call
back in the follow so the last used update on any access can be
re-instated. This requires DCACHE_MANAGE_TRANSIT to always be set.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When following a mount in rcu-walk mode we must check if the incoming dentry
is telling us it may need to block, even if it isn't actually a mountpoint.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: gcc 4.6 vs am33 inline assembly
MN10300: Deprecate gdbstub
MN10300: Allow KGDB to use the MN10300 serial ports
MN10300: Emulate single stepping in KGDB on MN10300
MN10300: Generalise kernel debugger kernel halt, reboot or power off hook
KGDB: Notify GDB of machine halt, reboot or power off
MN10300: Use KGDB
MN10300: Create generic kernel debugger hooks
MN10300: Create general kernel debugger cache flushing
MN10300: Introduce a general config option for kernel debugger hooks
MN10300: The icache invalidate functions should disable the icache first
MN10300: gdbstub: Restrict single-stepping to non-preemptable non-SMP configs
Guennadi Liakhovetski