There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in arc_emac_tx_clean() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes: 6eacf31139 ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Changes since v2 [1]:
* Merged with latest code changes
Changes since v1:
Update made thanks to David's review, much appreciated David.
* Improved inconsistent failure handling of clock rate setting
* For completeness of usecase, added arc_emac_probe error handling
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This operation is required for handling ioctl commands like SIOCGMIIREG,
when debugging MDIO registers from userspace.
This commit adds support for this operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver use phy_start_aneg() in arc_emac_open() to bring
up PHY. But phy_start() function is more appropriate for this purposes.
Besides that it call phy_start_aneg() as part of PHY startup sequence
it also can correctly bring up PHY from error and suspended states.
So the patch replace phy_start_aneg() to phy_start().
Also the patch add call to phy_stop() to arc_emac_stop() to allow
the PHY device to be fully suspended when the interface is unused.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependencies on the architectures that support these devices and
add compile test to ensure ongoing code build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch disable capturing multicast packets when multicast mode
disabled for ethernet ('ifconfig eth0 -multicast'). In that case
no multicast packet will be passed to kernel.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support was implemented by commit 775dd682e2
('arc_emac: implement promiscuous mode and multicast filtering').
It can be enabled explicity using 'ifconfig eth0 multicast'.
The patch is needed in order to remove explicit configuration
as most devices has multicast mode enabled by default.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in arc_emac_tx()
which can be called from hard irq context (netpoll) and from
other contexts. arc_emac_tx() only frees skbs that it has
dropped.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a94efbd7cc ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo in the driver, replace comma with a semicolon at the end
of statement. While using comma is a legal C here and probably does
not even generate compiler warning, it was unlikely the intention.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will make the driver more readability
The emac has the error and warnings if you run
'scripts/checkpatch.pl -f --subjective xxx' to check.
Let's clean up such trivial details.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to support the emac phy reset.
Different boards may require different phy reset duration. Add property
phy-reset-duration for emac driver, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RK3036's GRFs offset are different with RK3066/RK3188, and need to set
mac TX/RX clock before probe emac.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the RK3066/RK3188, there was fixed GRF offset configuration to set emac
and fixed DIV2 mac TX/RX clock. So, we need to easily set and fit to other
SoCs (RK3036) which maybe have different GRF offset, and need adjust mac
TX/RX clock.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After enter arc_emac_probe, emac will get_phy_id, phy_poll_reset and
other connecting PHY via mdiobus_read, so we need to set correct
ref clock rate for emac before probe emac.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `arc_emac_tx_clean':
emac_main.c:(.text+0x2decde): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `arc_emac_rx':
emac_main.c:(.text+0x2dee1c): undefined reference to `dma_unmap_single'
emac_main.c:(.text+0x2dee72): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2dee7e): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_probe':
(.text+0x2df2ee): undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `arc_emac_open':
emac_main.c:(.text+0x2df6d8): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df6e4): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_tx':
emac_main.c:(.text+0x2df9e4): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df9f0): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free resources before being disconnected from phy and calling core driver is
wrong and should not happen. It avoids a delay of 4-5s caused by the timeout of
phy_disconnect().
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused 'dev' variable from arc_emac_remove(), since it's
not being used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms have special bank registers which might be used to
select the correct clock or the right mode for Media Indepent Interface
controllers. Sometimes, it is also required to activate vcc regulators
in the right order to supply the ethernet controller at the right time.
This patch is an architecture refactoring of the arc-emac device driver.
It adds a new software design which allows to add specific platform
glue layer. Each platform has now its own module which performs custom
initialization and remove for the target and then calls to the
core driver.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an api changes for the emac_mdio.c module.
It will be required later when arc_emac_probe/arc_emac_remove
will no longer use 'struct platform_device'.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation of an api changes for the emac_main.c module.
The involved functions are arc_emac_probe and arc_emac_remove.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer to the struct net_device in the private data is only
assigned but never used, so delete it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
arc_emac_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the set_rx_mode function to enable/disable
promiscuous or all-multicast modes and to update the multicast
filtering list of the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe function at the moment only frees the netdev but does not disconnect
the phy or removes the mdio bus it registered.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
