This reverts commit b09f5ec18b.
Now that we have fully working BCMA_DRIVER_PCI symbol (in can be safely
disabled), there is no risk bcma will try to use PCI code without PCI
available.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It isn't required for bcma bus on SoCs, so provide some empty functions
and allow disabling it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog timer is used to put the device in a low-power mode when
it is idle for some time. This timer is stopped during that mode and
should be restarted upon activity. This has been broken by commit
d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch
restores the behaviour as it was before that commit.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware provides pointer to SDIO shared information at end of
RAM during firmware initialization. End of RAM is obviously determined
by the actual ram size, but part of that may be used for save&restore
memory. In that case another location in RAM will hold the pointer.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of hard-coded memory sizes it is possible to obtain that
information from the internal memory registers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the brcmf_chip_attach() function responsible for putting the
device in a state where it is accessible for firmware download.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions brcmf_chip_[enter/exit]_download() are not exclusively
used for firmware download so rename these more appropriate.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of checking the cores in the chip only if CONFIG_BRCMDBG
is selected perform the check always and extend it with more sanity
checking.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing the ramsize from the brcmf_sdio structure to avoid
duplication. The information is available in brcmf_chip
structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pre-requisite to shrink size of ieee80211_tx_info which in turn is
needed to shrink skb->cb to 40 bytes again.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we want to shrink skb->cb then we'd have to see about
reducing struct ieee80211_tx_info, which gets embedded inside
skb->cb[].
It provides a scratch space to be used by wireless drivers.
ar5523 uses the maximum space available today (40 bytes), but it seems
we don't need this -- data->skb pointer seems to always point back to the
skb whose cb buffer the data structure resides, iow, given a pointer to the
embedded control buffer we can infer the skb address.
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the RTT registers need to be configured for all
valid chains irrespective of the runtime chainmask,
use the actual chainmask of the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When assigning the initvals for PCIE sleep/awake
registers, check the configuration that has been
assigned to pll_pwrsave during initialization. Also,
display a warning if we don't have valid arrays.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These will be used to handle chip-specific
power save configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the AP, configuration may say not to bridge traffic between
wireless clients. This is conveyed from user space (ex: hostapd has
ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's
cfg80211 ops method change_bss
Add support for this setting.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is for AP only. If Rx data frame targeted to one of associated clients,
transmit it back to the wireless media and don't deliver to the host.
For the multicast frames, deliver to both host and wireless media.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is expected that driver completes NAPI when less than
full budget is consumed.
Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes add support for BCM4345 SDIO chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Syed Asifful Dayyan <syedd@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Msgbuf is using a wait_event_timeout to wait for the response on
an ioctl. The wakeup routine uses waitqueue_active to see if
wait_event_timeout has been called. There is a chance that the
response arrives before wait_event_timeout is called, this
will result in situation that wait_event_timeout never gets
woken again and assumed result will be a timeout. This patch
removes that errornous situation by always setting the
ctl_completed var before checking for queue active.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is using a "shared" variable to handoff ctl frames to DPC
and to see when they are done. In a timeout situation this can
lead to erroneous situation where DPC started to handle the ctl
frame while the timeout expired. This patch will fix this by
adding locking around the shared variable.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog thread is used to put the SDIO bus to sleep when the
system is idling. This patch simplifies the way it is determined
when sleep can be entered.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On removal of SDIO card both functions of card will be getting
a remove call. When the first is hanging in ctrl frame xmit then
the second will cause oops. This patch fixes the xmit ctrl
handling in case of serious errors and also limits the handling
for remove to function 1 only.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To prepare for reset ath5k should finish all asynchronous tasks. At
first, it disables the interrupt generation, then it waits for the
interrupt handler and tasklets completion, and then proceeds to the HW
configuration update. But it does not consider that the interrupt
handler or tasklet re-enables the interrupt generation. And we fall in a
situation when ath5k assumes that interrupts are disabled, but it is
not.
This can lead to different consequences, such as reception of the frame,
when we do not expect it. Under certain circumstances, this can lead to
the following warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
Fix this issue by adding a new status flag, which forbids to re-enable
the interrupt generation until the HW configuration is completed.
Note: previous patch, which reorders the Rx disable code helps to avoid
the above warning, but not fixes the root cause of unexpected frame
receiving.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath5k updates the channel pointer and after that it stops the Rx logic
and apply channel to HW. In case of channel switch, such sequence
creates a small window when a frame, which is received on the old
channel is considered as a frame received on the new one.
The most notable consequence of this situation occurs during the switch
from 2 GHz band (CCK+OFDM) to the 5GHz band (OFDM-only). Frame received
with CCK rate, e.g. beacon received at the 1mbps, causes the following
warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
The easiest way to reproduce this warning is to run scan with dualband
NIC in noisy environments, when the channel 11 runs multiple APs. In my
tests if the APs num >= 12, the warning appears in the first few
seconds of scanning.
In order to fix this, the Rx disable code moved to a higher level and
placed before the channel pointer update. This is also makes the code a
bit more symmetrical, since we disable and enable the Rx in the same
function.
In fact, at the pointer update time new frames should not appear,
because interrupt generation at this point should already be disabled.
The next patch should address this issue.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* 8000 device family work
* Update to the BT Coex firmware API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=l2Ap
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-03-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Location Aware Regulatory was added by Arik
* 8000 device family work
* Update to the BT Coex firmware API
In the case of AF_INET s_addr was set to INADDR_ANY (0) which which both
symmetric with the AF_INET6 case, where s_addr is not set, and unnecessary
as udp_conf is zeroed out earlier in the same function.
I suspect this change does not have any run-time effect due to compiler
optimisations. But it does make the code a little easier on the/my eyes.
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reobert Shearman noticed that mpls_egress is failing to verify that
the bytes to be examined are in fact present in the packet before
mpls_egress reads those bytes.
As suggested by David Miller reduce this to a single pskb_may_pull
call so that we don't do unnecessary work in the fast path.
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine (in drivers/net/phy/phy.c) will unconditionally
call phydev->adjust_link (macb_handle_link_change) when polling in the
PHY_CHANGELINK state. As currently written, macb always ends up
requesting a new tx_clk frequency in macb_handle_link_change. It is a
waste of time to request a new tx_clk frequency if the link state hasn't
changed, as the tx_clk will already be configured properly.
Let's only request a new tx_clk clock frequency when necessary.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Cc: Josh Cartwright <joshc@ni.com>
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo rhashtable_lookup_compare where we fail
to recompute the hash when looking up the new table. This causes
elements to be missed and potentially a crash during a resize.
Reported-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0c09bfdc4 ("rhashtable: avoid unnecessary wakeup for worker
queue") changed ht->shift to be atomic, which is actually unnecessary.
Instead of leaving the current shift in the core rhashtable structure,
it can be cached inside the individual bucket tables.
There, it will only be initialized once during a new table allocation
in the shrink/expansion slow path, and from then onward it stays immutable
for the rest of the bucket table liftime.
That allows shift to be non-atomic. The patch also moves hash_rnd
management into the table setup. The rhashtable structure now consumes
3 instead of 4 cachelines.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ying Xue <ying.xue@windriver.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential race condition between readers and the rehasher.
In particular, the rehasher could have started a rehash while the
reader finishes a scan of the old table but fails to see the new
table pointer.
This patch closes this window by adding smp_wmb/smp_rmb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
inet: tcp listener refactoring, part 8
These patches prepare request socks being hashed into general ehash
table : We declare 3 aliases (ireq_state, ireq_refcnt, ireq_family)
Note that refcnt is not yet handled, this will be done later.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before inserting request socks into general hash table,
fill their socket family.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ireq->ir_num contains local port, use it.
Also, get_openreq4() dumping listen_sk->refcnt makes litle sense.
inet_diag_fill_req() can also use ireq->ir_num
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_edemux() & sock_gen_put() should be ready to cope with request socks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make proto_register() & proto_unregister() a bit nicer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When request socks will be in ehash, they'll need to be refcounted.
This patch adds rsk_refcnt/ireq_refcnt macros, and adds
reqsk_put() function, but nothing yet use them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to identify request sock when they'll be visible in
global ehash table.
ireq_state is an alias to req.__req_common.skc_state.
Its value is set to TCP_NEW_SYN_RECV
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_SYN_RECV state is currently used by fast open sockets.
Initial TCP requests (the pseudo sockets created when a SYN is received)
are not yet associated to a state. They are attached to their parent,
and the parent is in TCP_LISTEN state.
This commit adds TCP_NEW_SYN_RECV state, so that we can convert
TCP stack to a different schem gradually.
This state is not exported to user space.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I forgot to update dccp_v6_conn_request() & cookie_v6_check().
They both need to set ireq->ireq_net and ireq->ir_cookie
Lets clear ireq->ir_cookie in inet_reqsk_alloc()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 33cf7c90fe ("net: add real socket cookies")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is possible in cls_bpf to access eBPF maps only under
rcu_read_lock_bh() variants: while on ingress side, that is, handle_ing(),
the classifier would be called from __netif_receive_skb_core() under
rcu_read_lock(); on egress side, however, it's rcu_read_lock_bh() via
__dev_queue_xmit().
This rcu/rcu_bh mix doesn't work together with eBPF maps as they require
soley to be called under rcu_read_lock(). eBPF maps could also be shared
among various other eBPF programs (possibly even with other eBPF program
types, f.e. tracing) and user space processes, so any context is assumed.
Therefore, a possible fix for cls_bpf is to wrap/nest eBPF program
invocation under non-bh RCU lock variant.
Fixes: e2e9b6541d ("cls_bpf: add initial eBPF support for programmable classifiers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
fib_trie: Minor fixes for table merge
This patch set addresses two issues reported with the tables merged, the
first is a NULL pointer dereference, and the other is to remove a WARN_ON
and set the ordering for aliases from different tables with the same slen
values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we should always have a deterministic ordering
for the main and local aliases within the merged table when two leaves
overlap.
So for example if we have a leaf with a key of 192.168.254.0. If we
previously added two aliases with a prefix length of 24 from both local and
main the first entry would be first and the second would be second. When I
was coding this I had added a WARN_ON should such a situation occur as I
wasn't sure how likely it would be. However this WARN_ON has been
triggered so this is something that should be addressed.
With this patch the ordering of the aliases is as follows. First they are
sorted on prefix length, then on their table ID, then tos, and finally
priority. This way what we end up doing is essentially interleaving the
two tables on what used to be leaf_info structure boundaries.
Fixes: 0ddcf43d5 ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function fib_unmerge assumed the local table had already been
allocated. If that is not the case however when custom rules are applied
then this can result in a NULL pointer dereference.
In order to prevent this we must check the value of the local table pointer
and if it is NULL simply return 0 as there is no local table to separate
from the main.
Fixes: 0ddcf43d5 ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Madhu Challa <challa@noironetworks.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
