Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock used by the hwbm functions must be initialized by the
network driver. This commit fixes this lack and the following erros when
lockdep is enabled:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14)
[<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0)
[<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060)
[<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0)
[<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68)
[<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc)
[<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490)
[<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284)
[<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0)
[<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0)
[<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4)
[<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c)
[<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218)
[<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8)
[<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc)
[<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc)
[<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114)
[<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24)
Fixes: baa11ebc0c ("net: mvneta: Use the new hwbm framework")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since appropriate memory barriers are already there, use the relaxed
version to improve performance a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to fix this before, but my previous fix was incomplete
and we can still get the same link error in randconfig builds
because of the way that Kconfig treats the
default y if MVNETA=y && MVNETA_BM_ENABLE
line that does not actually trigger when MVNETA_BM_ENABLE=m,
unlike I intended.
Changing the line to use MVNETA_BM_ENABLE!=n however has
the desired effect and hopefully makes all configurations
work as expected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 019ded3aa7 ("net: mvneta: bm: clarify dependencies")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mdiobus_scan() doesn't return NULL on failure anymore, this driver
no longer needs to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check for both, not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the following maybe-uninitialized warning:
drivers/net/ethernet/marvell/mvpp2.c:6007:18: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline
size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MVNETA_BM has a dependency on MVNETA, so we can only select the former
if the latter is enabled. However, the code dependency is the reverse:
The mvneta module can call into the mvneta_bm module, so mvneta cannot
be a built-in if mvneta_bm is a module, or we get a link error:
drivers/net/built-in.o: In function `mvneta_remove':
drivers/net/ethernet/marvell/mvneta.c:4211: undefined reference to `mvneta_bm_pool_destroy'
drivers/net/built-in.o: In function `mvneta_bm_update_mtu':
drivers/net/ethernet/marvell/mvneta.c:1034: undefined reference to `mvneta_bm_bufs_free'
This avoids the problem by further clarifying the dependency so that
MVNETA_BM is a silent Kconfig option that gets turned on by the
new MVNETA_BM_ENABLE option. This way both the core HWBM module and
the MVNETA_BM code are always built-in when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some literal values are actually already defined by macros, so let's use
them.
[gregory.clement@free-electrons.com: split intial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit corrects error printing when shutting down the port.
[gregory.clement@free-electrons.com: split initial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function eth_prepare_mac_addr_change() is called as part of MAC
address change. This function check if interface is running.
To enable change MAC address when interface is running:
IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous patch, the spinlock was not initialized. While it didn't
cause any trouble yet it could be a problem to use it uninitialized.
The most annoying part was the critical section protected by the spinlock
in mvneta_stop(). Some of the functions could sleep as pointed when
activated CONFIG_DEBUG_ATOMIC_SLEEP. Actually, in mvneta_stop() we only
need to protect the is_stopped flagged, indeed the code of the notifier
for CPU online is protected by the same spinlock, so when we get the
lock, the notifer work is done.
Reported-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta_percpu_notifier() hotplug callback lacks handling of the
CPU_DOWN_FAILED case. That means, if CPU_DOWN_PREPARE failes, the
driver is not well configured on the CPU.
Add handling for CPU_DOWN_FAILED[_FROZEN] hotplug notifier transition
to setup the driver.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the hardware buffer management framework had been introduced,
let's use it.
Tested-by: Sebastian Careba <nitroshift@yahoo.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer manager (BM) is a dedicated hardware unit that can be used by all
ethernet ports of Armada XP and 38x SoC's. It allows to offload CPU on RX
path by sparing DRAM access on refilling buffer pool, hardware-based
filling of descriptor ring data and better memory utilization due to HW
arbitration for using 'short' pools for small packets.
Tests performed with A388 SoC working as a network bridge between two
packet generators showed increase of maximum processed 64B packets by
~20k (~555k packets with BM enabled vs ~535 packets without BM). Also
when pushing 1500B-packets with a line rate achieved, CPU load decreased
from around 25% without BM to 20% with BM.
BM comprise up to 4 buffer pointers' (BP) rings kept in DRAM, which
are called external BP pools - BPPE. Allocating and releasing buffer
pointers (BP) to/from BPPE is performed indirectly by write/read access
to a dedicated internal SRAM, where internal BP pools (BPPI) are placed.
BM hardware controls status of BPPE automatically, as well as assigning
proper buffers to RX descriptors. For more details please refer to
Functional Specification of Armada XP or 38x SoC.
In order to enable support for a separate hardware block, common for all
ports, a new driver has to be implemented ('mvneta_bm'). It provides
initialization sequence of address space, clocks, registers, SRAM,
empty pools' structures and also obtaining optional configuration
from DT (please refer to device tree binding documentation). mvneta_bm
exposes also a necessary API to mvneta driver, as well as a dedicated
structure with BM information (bm_priv), whose presence is used as a
flag notifying of BM usage by port. It has to be ensured that mvneta_bm
probe is executed prior to the ones in ports' driver. In case BM is not
used or its probe fails, mvneta falls back to use software buffer
management.
A sequence executed in mvneta_probe function is modified in order to have
an access to needed resources before possible port's BM initialization is
done. According to port-pools mapping provided by DT appropriate registers
are configured and the buffer pools are filled. RX path is modified
accordingly. Becaues the hardware allows a wide variety of configuration
options, following assumptions are made:
* using BM mechanisms can be selectively disabled/enabled basing
on DT configuration among the ports
* 'long' pool's single buffer size is tied to port's MTU
* using 'long' pool by port is obligatory and it cannot be shared
* using 'short' pool for smaller packets is optional
* one 'short' pool can be shared among all ports
This commit enables hardware buffer management operation cooperating with
existing mvneta driver. New device tree binding documentation is added and
the one of mvneta is updated accordingly.
[gregory.clement@free-electrons.com: removed the suspend/resume part]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit 2dcf75e279 ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f864288544 ("net: mvneta: Statically assign queues to CPUs")
Reported-by: Stefan Roese <stefan.roese@gmail.com>
Suggested-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
position p,q;
@@
e@q = kzalloc(...);
if@p (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
This function may also return -1 after calling mpp2_prs_tcam_port_map_get.
So that the function consistently returns meaningful error values on
failure, the -1 is changed to -EINVAL.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in txq_put_data() would use txq->tx_curr_desc to index the
tso_hdrs/tso_hdrs_dma buffers, for less than 8 bytes unaligned
fragments, which is already moved to the next descriptor at the
beginning of the function.
If that fragment was the last of the the skb, the next skb would use
that same space to place the ip headers, overwritting that small
fragment data.
Fixes: 91986fd3d3 (net: mv643xx_eth: Ensure proper data alignment in TSO TX path)
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Reviewed-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic. Obviously this bus clk also need to
be enabled. This patch adds this optional "bus" clk support.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic.
To support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "core"
clock before falling back to unnamed clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers in the future.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When s->type is T_REG_64, the high 32bits are lost in val. This patch
fixes this trivial issue.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 9b0cdefa4c ("net: mvneta: add ethtool statistics")
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch each CPU is associated with its own set of TX queues.
It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.
This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.
This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.
Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation
is to modify the device tree.
This is needed if you plan to use the same kernel with
different ethernet switches, the ones that support the in-band
status and the ones that not.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves autoneg-related bit manipulations to the single place.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e328941 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing an interface's MTU, then bringing the interface down and
back up again, I immediately saw tons of kernel messages like below.
The reason for this bad behavior is mvneta_rxq_drop_pkts(), which calls
dma_unmap_single() on already-freed memory. So we need to switch the
order of those two operations.
[ 152.388518] BUG: Bad page state in process ifconfig pfn:1b518
[ 152.388526] page:dff3dbc0 count:0 mapcount:0 mapping: (null) index:0x0
[ 152.395178] flags: 0x200(arch_1)
[ 152.398441] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[ 152.398446] bad because of flags:
[ 152.398450] flags: 0x200(arch_1)
[ 152.401716] Modules linked in:
[ 152.401728] CPU: 0 PID: 1453 Comm: ifconfig Tainted: P B O 4.1.12.armada.1 #1
[ 152.401733] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 152.401749] [<c0015b1c>] (unwind_backtrace) from [<c0011d8c>] (show_stack+0x10/0x14)
[ 152.401762] [<c0011d8c>] (show_stack) from [<c06aa68c>] (dump_stack+0x74/0x90)
[ 152.401772] [<c06aa68c>] (dump_stack) from [<c0096c08>] (bad_page+0xc4/0x124)
[ 152.401783] [<c0096c08>] (bad_page) from [<c0099378>] (get_page_from_freelist+0x4e4/0x644)
[ 152.401794] [<c0099378>] (get_page_from_freelist) from [<c0099620>] (__alloc_pages_nodemask+0x148/0x784)
[ 152.401805] [<c0099620>] (__alloc_pages_nodemask) from [<c00ac658>] (kmalloc_order+0x10/0x20)
[ 152.401818] [<c00ac658>] (kmalloc_order) from [<c04c6f44>] (mvneta_rx_refill+0xc4/0xe8)
[ 152.401830] [<c04c6f44>] (mvneta_rx_refill) from [<c04c96c0>] (mvneta_setup_rxqs+0x298/0x39c)
[ 152.401842] [<c04c96c0>] (mvneta_setup_rxqs) from [<c04c9904>] (mvneta_open+0x3c/0x150)
[ 152.401853] [<c04c9904>] (mvneta_open) from [<c0597764>] (__dev_open+0xac/0x124)
[ 152.401864] [<c0597764>] (__dev_open) from [<c05979e4>] (__dev_change_flags+0x8c/0x148)
[ 152.401875] [<c05979e4>] (__dev_change_flags) from [<c0597ac0>] (dev_change_flags+0x18/0x48)
[ 152.401886] [<c0597ac0>] (dev_change_flags) from [<c060d308>] (devinet_ioctl+0x620/0x6d0)
[ 152.401897] [<c060d308>] (devinet_ioctl) from [<c057d810>] (sock_ioctl+0x64/0x288)
[ 152.401908] [<c057d810>] (sock_ioctl) from [<c00dcb7c>] (do_vfs_ioctl+0x78/0x608)
[ 152.401918] [<c00dcb7c>] (do_vfs_ioctl) from [<c00dd170>] (SyS_ioctl+0x64/0x74)
[ 152.401930] [<c00dd170>] (SyS_ioctl) from [<c000f3a0>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed_phy infrastructure is done in a way that is optional,
by providing 'static inline' helper functions doing nothing in
include/linux/phy_fixed.h for all its APIs. However, three out
of the four users (DSA, BCMGENET, and SYSTEMPORT) always
'select FIXED_PHY', presumably because they need that.
MVNETA is the fourth one, and if that is built-in but FIXED_PHY
is configured as a loadable module, we get a link error:
drivers/built-in.o: In function `mvneta_fixed_link_update':
fpga-mgr.c:(.text+0x33ed80): undefined reference to `fixed_phy_update_state'
Presumably this driver has the same dependency as the others,
so this patch also uses 'select' to ensure that the fixed-phy
support is built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 898b2970e2 ("mvneta: implement SGMII-based in-band link state signaling")
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.
This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.
Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some embedded systems the EEPROM does not contain a valid MAC address.
In that case it is better to fallback to a generated mac address and
let init scripts fix the value later.
Reported-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
[Changed handcoded setup to use eth_hw_addr_random() and to save new address into HW]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the switch to per-CPU interrupts, we lost the ability to set which
CPU was going to receive our RX interrupt, which was now only the CPU on
which the mvneta_open function was run.
We can now assign our queues to their respective CPUs, and make sure only
this CPU is going to handle our traffic.
This also paves the road to be able to change that at runtime, and later on
to support RSS.
[gregory.clement@free-electrons.com]: hardened the CPU hotplug support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver allows to change the default RX queue trough the rxq_def
kernel parameter.
However, the current code doesn't allow to have any value but 0. It is
actively checked for in the driver's probe because the drivers makes a
number of assumption and takes a number of shortcuts in order to just use
that RX queue.
Remove these limitations in order to be able to specify any available
queue.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that our interrupt controller is allowing us to use per-CPU interrupts,
actually use it in the mvneta driver.
This involves obviously reworking the driver to have a CPU-local NAPI
structure, and report for incoming packet using that structure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.
However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.
This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d79 ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression introduced by the commit a84e328941
("net: mvneta: fix refilling for Rx DMA buffers"). Due to this commit
the newly allocated Rx buffers are DMA-unmapped in place of those passed
to the networking stack. Obviously, this causes data corruptions.
This patch fixes the issue by ensuring that the right Rx buffers are
DMA-unmapped.
Reported-by: Oren Laskin <oren@igneous.io>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: a84e328941 ("net: mvneta: fix refilling for Rx DMA buffers")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Oren Laskin <oren@igneous.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code around the allocation and loops are a bit obfuscated.
Neaten it by using:
o kcalloc with decimal count and sizeof(u32)
o Decimal loop indexing and i++ not i += 4
o A promiscuous block using a similar style
to the multicast block
o Remove unnecessary variables
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The double memset is a little ugly; using kzalloc avoids it altogether.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).
When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.
The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.
This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.
This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.
This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.
This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reported-by: Alexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 898b2970e2 ("mvneta: implement SGMII-based in-band link state
signaling") implemented the link parameters auto-negotiation unconditionally.
Unfortunately it appears that some HW that implements SGMII protocol,
doesn't generate the inband status, so it is not possible to auto-negotiate
anything with such HW.
This patch enables the auto-negotiation only if explicitly requested with
the 'managed' DT property.
This patch fixes the following regression:
https://lkml.org/lkml/2015/7/8/865
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With the actual code, if a memory allocation error happens while
refilling a Rx descriptor, then the original Rx buffer is both passed
to the networking stack (in a SKB) and let in the Rx ring. This leads
to various kernel oops and crashes.
As a fix, this patch moves Rx descriptor refilling ahead of building
SKB with the associated Rx buffer. In case of a memory allocation
failure, data is dropped and the original DMA buffer is put back into
the Rx ring.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Yoann Sculo <yoann@sculo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet controller found in the Armada 370, 380 and 385 SoCs don't
support TCP/IP checksumming with frame sizes larger than 1600 bytes.
This patch fixes the issue by disabling the features NETIF_F_IP_CSUM and
NETIF_F_TSO for the Armada 370 and compatibles SoCs when the MTU is set
to a value greater than 1600 bytes.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver supports the Ethernet IP found in the Armada 370, XP,
380 and 385 SoCs. Since at least one more hardware feature is available
for the Armada XP SoCs then a way to identify them is needed.
This patch introduces a new compatible string "marvell,armada-xp-neta".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 898b2970e2 ("mvneta: implement SGMII-based in-band link state
signaling")
changed mvneta_adjust_link() so that it does not clear the auto-negotiation
bits in MVNETA_GMAC_AUTONEG_CONFIG register. This was necessary for
auto-negotiation mode to work.
Unfortunately I haven't checked if these bits are ever initialized.
It appears they are not.
This patch adds the missing initialization of the auto-negotiation bits
in the MVNETA_GMAC_AUTONEG_CONFIG register.
It fixes the following regression:
https://www.mail-archive.com/netdev@vger.kernel.org/msg67928.html
Since the patch was tested to fix a regression, it should be applied to
stable tree.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e, func, da;
@@
-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 43d3ddf87a ("net: pxa168_eth: add device tree support") starts
to use managed resources by adding devm_clk_get() and
devm_ioremap_resource(), but it leaves explicit iounmap() and clock_put()
in pxa168_eth_remove() and in failure handling code of pxa168_eth_probe().
As a result double free can happen.
The patch removes explicit resource deallocation. Also it converts
clk_disable() to clk_disable_unprepare() to make it symmetrical with
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_adjust_link() is a callback for of_phy_connect() and should
not be called directly. The result of calling it directly is as below:
Signed-off-by: David S. Miller <davem@davemloft.net>
When MDIO bus is unavailable (common setup for SGMII), the in-band
signaling must be used to correctly track link state.
This patch enables the in-band status delivery for link state changes, namely:
- link up/down
- link speed
- duplex full/half
fixed_phy_update_state() is used to update phy status.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69ad0dd7af
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31f ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sky2_change_mtu setting B0_IMSK to 0 may be delayed due to PCI write posting
which could result in irqs being still active when synchronize_irq is called.
Since we are not prepared to handle any further irqs after synchronize_irq
(our resources are freed after that) force the write by a consecutive read from
the same register.
Similar situation in sky2_all_down: Here we disabled irqs by a write to B0_IMSK
but did not ensure that this write took place before synchronize_irq. Fix that
too.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a spurious interrupt dont forget to reenable the interrupts that
have been masked by reading the interrupt source register.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pxa168_eth_open() the irqs are enabled before napi. This opens a tiny time
window in which the irq handler is processed, disables irqs but then is not able
to schedule the not yet activated napi, leaving irqs disabled forever (since
irqs are reenabled in napi poll function).
Fix this race by activating napi before irqs are activated.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sky2->tx_le = pci_alloc_consistent() or sky2->tx_ring = kcalloc() in
sky2_alloc_buffers() fails, sky2->rx_ring = kcalloc() will never be called.
In this error case handling, sky2_rx_clean() is called from within
sky2_free_buffers().
In sky2_rx_clean() we find the following:
...
memset(sky2->rx_le, 0, RX_LE_BYTES);
...
This results in a memset using a NULL pointer and will crash the system.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a random RSS key rather than a fixed one.
Using netdev_rss_key_fill helper also ensures that all ports share
a common key.
See also commit 960fb622f8.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to ensure the net_device's dev.parent is set before we used it
in dma_zalloc_coherent() from init_hash_table().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_print_status() to report a change in the PHY status.
The current message is not verbose enough, so this commit improves
it by using the generic status message.
After this change, the kernel reports PHY status down and up events as:
mvneta f1070000.ethernet eth0: Link is Down
mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
With properly using libphy PHYs now, remove the in-driver PHY
mangling.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Ethernet IP supports PHY negotiation driven by HW. This
fundamentally clashes with libphy (software) driven negotiation and
also cannot cope with quirky PHYs. Therefore, always disable any HW
negotiation features and properly use libphy's phy_device.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current libphy handling in pxa168_eth lacks proper phy_connect. Prepare
to fix this by first moving phy properties from platform_data to private
driver data.
Tested-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `rxq_deinit':
pxa168_eth.c:(.text+0x2a2f2e): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_reclaim':
pxa168_eth.c:(.text+0x2a3044): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `txq_deinit':
pxa168_eth.c:(.text+0x2a310a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_init':
pxa168_eth.c:(.text+0x2a3226): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_init':
pxa168_eth.c:(.text+0x2a32d4): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `init_hash_table':
pxa168_eth.c:(.text+0x2a3354): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_refill':
pxa168_eth.c:(.text+0x2a345a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `rxq_process':
pxa168_eth.c:(.text+0x2a39cc): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `pxa168_eth_remove':
pxa168_eth.c:(.text+0x2a3b84): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `pxa168_eth_start_xmit':
pxa168_eth.c:(.text+0x2a3e8a): undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signedness bugs may occur when using signed char for bitops,
depending on if the highest bit is ever used.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PXA168_ETH need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):
CC [M] drivers/net/ethernet/marvell/pxa168_eth.o
drivers/net/ethernet/marvell/pxa168_eth.c: In function ‘pxa168_eth_probe’:
drivers/net/ethernet/marvell/pxa168_eth.c:1605:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(pep->base);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dependency to COMPILE_TEST so that the driver can be compiled for
test purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Berlin SoCs have an Ethernet controller compatible with the pxa168.
Allow these SoCs to use the pxa168_eth driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the way the MAC address is retrieved. The MAC address
can now, in addition to being random, be set in the device tree or
retrieved from the Ethernet controller MAC address registers. The
probing function will try to get a MAC address in the following order:
- From the device tree.
- From the Ethernet controller MAC address registers.
- Generate a random one.
This patch also adds a function to read the MAC address from the
Ethernet Controller registers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address, in addition to updating the dev_addr in
the net_device structure, this patch also update the MAC address
registers (high and low) of the Ethernet controller with the new MAC.
The address stored in these registers is used for IEEE 802.3x Ethernet
flow control, which is already enabled.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3x Ethernet flow control is disabled when bit (1 << 2) is set
in the port status register. Fix the flow control detection in the link
event handling function which was relying on the opposite assumption.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device tree support to the pxa168_eth driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a bit the pxa168_eth driver before adding the device tree
support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_skb_tx_csum':
drivers/net/ethernet/marvell/mvneta.c:1374:3: error: implicit declaration of function 'vlan_get_protocol' [-Werror=implicit-function-declaration]
__be16 l3_proto = vlan_get_protocol(skb);
^
Reporeted-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver doesn't appear to support vlan acceleration at
all. However, it does claim to support TSO and IP checksums
for vlan devices. Thus any configured vlan device would
end up passing down partial checksums or TSO frames.
The driver also uses the value from skb->protocol to
determine TSO and checksum offload information, but assumes
that skb->protocol holds the l3 protocol information.
As a result, vlan traffic with partial checksums or TSO
will fail those checks and TSO will not happen.
Fix this by using vlan_get_protocol() helper.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there is a "phy" handle the probe function returns with holding a
reference to that node. Make sure that in the fixed phy case there is
also held a reference to yield a consistant state.
Also add the corresponding of_node_put in the error path and the remove
function.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is similar to commit 4d12bc63ab ("net: mvneta: fix
operation in 10 Mbit/s mode"), but this time for the mvpp2 driver. The
driver was properly taking into account the 1 Gbit/s and 100 Mbit/s
speeds, but not the 10 Mbit/s, which was handled as 100
Mbit/s. However, the MVPP2_GMAC_CONFIG_MII_SPEED bit in the
MVPP2_GMAC_AUTONEG_CONFIG register must remain cleared to allow 10
Mbit/s operation. This commit therefore fixes 10 Mbit/s operation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the users of mvpp2_bm_bufs_free() have been fixed, we can safely
clean the function prototype.
The function is always called to release all the buffers in a BM pool, and
the number of buffers freed is not needed. Therefore, we change the return
to a void, and remove the "num" parameter. This is a cosmetic change, to
make the code slightly cleaner.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a call to mvpp2_bm_bufs_free(), the caller usually wants to know
if the function successfully freed the requested number. However, this
cannot be done by looking into the BM pool count, because the current
buffer count was updated by mvpp2_bm_bufs_free().
In fact, the current callers of mvpp2_bm_bufs_free() use it to release
all the buffers in the pool, so we can fix this by simply checking
if the pool is not empty.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the network interfaces that are not configured by the bootloader
(using e.g. tftp or ping) can detect the link status but are unable to
transmit data.
The network controller has a functionality that allows the hardware to
continuously poll the PHY and directly update the MAC configuration accordingly
(speed, duplex, etc.). However, this doesn't work well with phylib's
software-based polling and updating MAC configuration in the driver's callback.
This commit fixes this issue by:
1. Setting MVPP2_PHY_AN_STOP_SMI0_MASK in MVPP2_PHY_AN_CFG0_REG in
mvpp2_init(), which disables the harware polling feature.
2. Disabling MVPP2_GMAC_PCS_ENABLE_MASK bit in MVPP2_GMAC_CTRL_2_REG in
mvpp2_port_mii_set() for port types other than SGMII.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was originally wrong, the correct value is BIT(1), so fix it.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENODEV from the no ports enabled error handling
case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper string for this license is "GPL v2", instead of "GPLv2".
This commit fixes that.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.
Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added FUJITSU SIEMENS A8NE-FM to the list of 32bit DMA boards
>From Tomi O.:
After I added an entry to this MB into the skge.c
driver in order to enable the mentioned 64bit dma disable quirk,
the network data corruptions ended and everything is fine again.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.
This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'weight' field is only used to pass the weigth to napi initialization
function. This commit removes the field, and instead uses a fixed value to
initialize the napi context.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes use of devm_kmalloc_array() for memory allocation and the
recently introduced devm_mdiobus_alloc() API to simplify driver's code.
While here, remove a redundant out of memory error message.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not support multiple rx queues, and so it's a waste
of resources to have a default number larger than one (1).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_prepare_mac_addr_change and eth_commit_mac_addr_change, instead
of manually checking and storing the MAC address, which makes the
code slightly more robust. This fixes the lack of valid MAC address check
in the driver's .ndo_set_mac_address hook.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit cleans-up mvneta_init(), which initializes the hardware
and allocates the rx/qx queues. The queue allocation is simplified
by using devm_kcalloc instead of kzalloc. The unused phy_addr parameter
is removed. While here, the 'hal' references in the comments are removed.
This commit makes no functionality change.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit checks the return code of mvneta_setup_txq() call
in mvneta_change_mtu(). Also, use the netdevice pointer directly
instead of dereferencing the port structure. While here, let's
fix a tiny comment typo.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tiny clean-up to improve readability. This commit makes no functionality
change.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mv643xx_eth_adjust_link() is only used to call mv643xx_adjust_pscr().
This commit renames the latter to the former, and therefore removes the extra
and useless function.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the TSO helper API has been introduced, this commit makes use
of it to add support for software TSO in this driver.
This feature allows to improve outbound throughput performance significantly.
Running iperf tests shows a 30% improvement, tested on a Kirkwood Openblocks
A6 board.
$ ethtool -K eth0 tso off
$ iperf -c 192.168.0.45 -t 3
------------------------------------------------------------
Client connecting to 192.168.0.45, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.0.159 port 46389 connected with 192.168.0.45 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 217 MBytes 607 Mbits/sec
$ ethtool -K eth0 tso on
$ iperf -c 192.168.0.45 -t 3
------------------------------------------------------------
Client connecting to 192.168.0.45, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.0.159 port 46390 connected with 192.168.0.45 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 336 MBytes 938 Mbits/sec
This commit is just an example of the usage of the TSO API, it works fine
but needs some more work. In particular, the descriptor unmapping path must
avoid unmapping the TSO headers.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dma_map_single() instead of skb_frag_dma_map() allows to unmap
all the descriptors using dma_unmap_single(). This change allows
to introduce software TSO in a less intrusive way.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to ease the addition of new features, let's factorize the
feature list.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in the datasheet, the driver can set the "L4Chk_Mode" flag
(bit 10) in the Tx descriptor command/status to specify that a frame is not
IP fragmented and that the controller is in charge of generating the TCP/IP
checksum. This must be used together with the "GL4chk" flag (bit 17).
These two flags allow to avoid setting the initial TCP checksum in the l4i_chk
field of the Tx descriptor, which is needed to support software TSO.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable by moving the initial checksum setup
and the command/status preparation to its own function.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the TSO helper API has been introduced, this commit makes use
of it to implement the TSO in this driver.
Using iperf to test and vmstat to check the CPU usage, shows a substantial
CPU usage drop when TSO is on (~15% vs. ~25%). HTTP-based tests performed
by Willy Tarreau have shown performance improvements.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework mvneta_tx() so that the code that performs the final handling
before a sk_buff is transmitted is done only if the numbers of fragments
processed if positive.
This is preparation work to add the support for software TSO.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to ease the addition of new features, let's factorize the
feature list.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the introduction of of_phy_register_fixed_link(), this patch
introduces fixed link support in the mvneta driver, for Marvell Armada
370/XP SOCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
commit 9ec36cafe4
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 23 17:57:41 2014 -0500
of/irq: do irq resolution in platform_get_irq
changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.
Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.
While at it, add a proper handling for the deferral probe case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.
In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.
Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:
- QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured in QSGMII. Technically speaking,
configuring the SERDES of the first port would be sufficient, but
it is simpler to do it on all ports.
- SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured as SGMII.
- RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
cleared, and no SERDES configuration is done, because RGMII is not
using SERDES lanes.
- other: an error is returned. For this reason, the
mvneta_port_power_up() now returns an int instead of nothing, and
the return value is checked by mvneta_probe().
This has been successfully tested on:
* Armada XP DB, which has two RGMII and two SGMII connections
* Armada XP GP, which uses QSGMII for its four interfaces
* Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e3a8786c10. While
this commit allows to use the mvneta driver as a module on some
configurations, it breaks other configurations even if mvneta is used
built-in.
This breakage is due to the fact that on some RGMII platforms, the PCS
bit has to be set, and on some other platforms, it has to be
cleared. At the moment, we lack informations to know exactly the
significance of this bit (the datasheet only says "enables PCS"), and
so we can't produce a patch that will work on all platforms at this
point. And since this change is breaking the network completely for
many users, it's much better to revert it for now. We'll come back
later with a proper fix that takes into account all platforms.
Basically:
* Armada XP GP is configured as RGMII-ID, and needs the PCS bit to be
set.
* Armada 370 Mirabox is configured as RGMII-ID, and needs the PCS bit
to be cleared.
And at the moment, we don't know how to make the distinction between
those two cases. One hint is that the Armada XP GP appears in fact to
be using a QSGMII connection with the PHY (Quad-SGMII), but
configuring it as SGMII doesn't work, while RGMII-ID works. This needs
more investigation, but in the mean time, let's unbreak the network
for all those users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Alexander Reuter <Alexander.Reuter@gmx.net>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=73401
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
orion_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309 mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in sky2_xmit_frame that
can be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any skge_xmit_free that can
be called in hard irq and other contexts, on the path that
handles dropped packets.
Replace dev_kfree_skb with dev_consume_skb_any in skge_tx_done that can
be called in hard irq and other contexts, on the path that handles
successfully transmitted skbs.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any in mv643xx_eth_xmit and
txq_submit_skb that can be called in hard irq and other contexts,
on paths where the skbs are dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads the mac address from the device registers which would
need to have been programmed by the bootloader. This patch adds
the ability to pull the mac from devicetree via the pci device dt node.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Changes since v2:
- eliminated use of stack tmpaddr per feedback
Changes since v1:
- simplified based on feedback
- fixed formatting
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.
In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
