There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_DEF quirk. Add a corresponding entry in
the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userptr can be very useful if a UVC camera is requested to use video
buffers allocated by another processing device. So that buffers don't
need to be copied.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support 32-bit/64-bit compatibility for the the UVCIOC_ ioctls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-EINVAL is the wrong error code in that case, replace it with -ENOTTY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers implementing custom ioctls need to handle 32-bit/64-bit
compatibility themselves. Provide them with a way to do so.
To avoid circular module dependencies, merge the v4l2-compat-ioctl32
module into videodev. There is no point in keeping them separate, as the
v4l2_compat_ioctl32() function is required by videodev if CONFIG_COMPAT
is set anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
WARNING: drivers/media/radio/built-in.o(.data+0x284): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/media/built-in.o(.data+0x48200): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a small extension to the S_HW_FREQ_SEEK ioctl: if the wrap_around
value is not support by the hardware, then -EINVAL is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card is based on the tea575x receiver. Use the tea575x-tuner framework
instead of reinventing the wheel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix HW seek in TEA575x to work properly:
- a delay must be present after search start and before first register read
or the seek does weird things
- when the search stops, the new frequency is not available immediately, we
must wait until it appears in the register (fortunately, we can clear the
frequency bits when starting the search as it starts at the frequency
currently set, not from the value written)
- sometimes, seek remains on the current frequency (or moves only a little),
so repeat it until it moves by at least 50 kHz
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tea575x-tuner module has been updated to use the latest V4L2 framework
functionality. This also required changes in the drivers that rely on it.
The tea575x changes are:
- The drivers must provide a v4l2_device struct to the tea module.
- The radio_nr module parameter must be part of the actual radio driver,
and not of the tea module.
- Changed the frequency range to the normal 76-108 MHz range instead of
50-150.
- Add hardware frequency seek support.
- Fix broken rxsubchans/audmode handling.
- The application can now select between stereo and mono.
- Support polling for control events.
- Add V4L2 priority handling.
And radio-sf16fmr2.c now uses the isa bus kernel framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When reading IF_AGC_GAIN register a wrong value for the base address
register was used (STB0899_DEMOD instead of STB0899_S2DEMOD). That
lead to a wrong signal strength value on DVB-S2 transponders.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_read_status the FE_HAS_SIGNAL flag was not set in case of a
successful carrier lock. This change fixes that.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b2a29b578d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiří Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 28d82dc1c4 ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).
The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.
This is captured in: https://bugzilla.redhat.com/show_bug.cgi?id=681578
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David Miller:
"1) icmp6_dst_alloc() returns NULL instead of ERR_PTR() leading to
crashes, particularly during shutdown. Reported by Dave Jones and
fixed by Eric Dumazet.
2) hyperv and wimax/i2400m return NETDEV_TX_BUSY when they have
already freed the SKB, which causes crashes as to the caller this
means requeue the packet. Fixes from Eric Dumazet.
3) usbnet driver doesn't allocate the right amount of headroom on
fresh RX SKBs, fix from Eric Dumazet.
4) Fix regression in ip6_mc_find_dev_rcu(), as an RCU lookup it
abolutely should not take a reference to 'dev', this leads to
leaks. Fix from RonQing Li.
5) Fix netfilter ctnetlink race between delete and timeout expiration.
From Pablo Neira Ayuso.
6) Revert SFQ change which causes regressions, specifically queueing
to tail can lead to unavoidable flow starvation. From Eric
Dumazet.
7) Fix a memory leak and a crash on corrupt firmware files in bnx2x,
from Michal Schmidt."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools, x86: Build perf on older user-space as well
perf tools: Use scnprintf where applicable
perf tools: Incorrect use of snprintf results in SEGV
Kerin Millar reported hardlockups while running `conntrackd -c'
in a busy firewall. That system (with several processors) was
acting as backup in a primary-backup setup.
After several tries, I found a race condition between the deletion
operation of ctnetlink and timeout expiration. This patch fixes
this problem.
Tested-by: Kerin Millar <kerframil@gmail.com>
Reported-by: Kerin Millar <kerframil@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't
need to dev_hold().
With dev_hold(), not corresponding dev_put(), will lead to leak.
[ bug introduced in 96b52e61be (ipv6: mcast: RCU conversions) ]
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge some more email patches from Andrew Morton:
"A couple of nilfs fixes"
* emailed from Andrew Morton <akpm@linux-foundation.org>:
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
ns_r_segments_percentage is read from the disk. Bogus or malicious
value could cause integer overflow and malfunction due to meaningless
disk usage calculation. This patch reports error when mounting such
bogus volumes.
Signed-off-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull maintainer update from James Morris:
"Please pull this patch which adds Serge as maintainer of the
capabilities code, as discussed on lwn and the lsm list.
New capabilities must be signed off by the maintainer, and new uses of
any capabilities should at be cc'd to the maintainer."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
MAINTAINERS: Add Serge as maintainer of capabilities
a newer assembler (v2.22 complains about it, v2.20 ignores it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=dMe3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
Pull c6x bugfix from Mark Salter:
"Remove dead code from entry.S which causes a build failure when using
a newer assembler (v2.22 complains about it, v2.20 ignores it)."
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
C6X: remove dead code from entry.S
When writing files to afs I sometimes hit a BUG:
kernel BUG at fs/afs/rxrpc.c:179!
With a backtrace of:
afs_free_call
afs_make_call
afs_fs_store_data
afs_vnode_store_data
afs_write_back_from_locked_page
afs_writepages_region
afs_writepages
The cause is:
ASSERT(skb_queue_empty(&call->rx_queue));
Looking at a tcpdump of the session the abort happens because we
are exceeding our disk quota:
rx abort fs reply store-data error diskquota exceeded (32)
So the abort error is valid. We hit the BUG because we haven't
freed all the resources for the call.
By freeing any skbs in call->rx_queue before calling afs_free_call
we avoid hitting leaking memory and avoid hitting the BUG.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A read of a large file on an afs mount failed:
# cat junk.file > /dev/null
cat: junk.file: Bad message
Looking at the trace, call->offset wrapped since it is only an
unsigned short. In afs_extract_data:
_enter("{%u},{%zu},%d,,%zu", call->offset, len, last, count);
...
if (call->offset < count) {
if (last) {
_leave(" = -EBADMSG [%d < %zu]", call->offset, count);
return -EBADMSG;
}
Which matches the trace:
[cat ] ==> afs_extract_data({65132},{524},1,,65536)
[cat ] <== afs_extract_data() = -EBADMSG [0 < 65536]
call->offset went from 65132 to 0. Fix this by making call->offset an
unsigned int.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ENDPROC() on sys_fadvise64_c6x() in arch/c6x/kernel/entry.S is
outside of the conditional block with the matching ENTRY() macro. This
leads a newer (v2.22 vs. v2.20) assembler to complain:
/tmp/ccGZBaPT.s: Assembler messages:
/tmp/ccGZBaPT.s: Error: .size expression for sys_fadvise64_c6x does not evaluate to a constant
The conditional block became dead code when c6x switched to generic
unistd.h and should be removed along with the offending ENDPROC().
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Also increments tx_dropped counter
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
This is mostly a revert of commit bf769375c (staging: hv: fix the return
status of netvsc_start_xmit())
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.
This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.
Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d47a0ac7b6 (sch_sfq: dont put new flow at the end of
flows)
As Jesper found out, patch sounded great but has bad side effects.
In stress situation, pushing new flows in front of the queue can prevent
old flows doing any progress. Packets can stay in SFQ queue for
unlimited amount of time.
It's possible to add heuristics to limit this problem, but this would
add complexity outside of SFQ scope.
A more sensible answer to Dave Taht concerns (who reported the issued I
tried to solve in original commit) is probably to use a qdisc hierarchy
so that high prio packets dont enter a potentially crowded SFQ qdisc.
Reported-by: Jesper Dangaard Brouer <jdb@comx.dk>
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 87a115783 ( ipv6: Move xfrm_lookup() call down into
icmp6_dst_alloc().) forgot to convert one error path, leading
to crashes in mld_sendpack()
Many thanks to Dave Jones for providing a very complete bug report.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Serge as maintainer of capabilities, per suggestion on LWN:
http://lwn.net/Articles/486306/
Signed-off-by: James Morris <james.l.morris@oracle.com>
Merge patches from Andrew Morton:
"Nine patches - some bug fixes and some MAINTAINERS fiddling."
* emailed from Andrew Morton <akpm@linux-foundation.org>:
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
MAINTAINERS: add Johan to Bluetooth maintainers
MAINTAINERS: Gustavo has moved
prctl: use CAP_SYS_RESOURCE for PR_SET_MM option
rapidio/tsi721: fix bug in register offset definitions
MAINTAINERS: update ST's Mailing list for SPEAr
memcg: free mem_cgroup by RCU to fix oops
Pull i2c subsystem fixes from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-algo-bit: Fix spurious SCL timeouts under heavy load
i2c-core: Comment says "transmitted" but means "received"
Pull drm exynos/intel updates from Dave Airlie:
"Two minor updates from Jesse for Intel SNB fixes, and a few fixes from
Samsung for exynos. The pull req has Alan's commit in it since Intel
based their tree on my tree at that time, but it all seems fine wrt
merging."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm exynos: use drm_fb_helper_set_par directly
drm/exynos: Fix fb_videomode <-> drm_mode_modeinfo conversion
drm/exynos: fix runtime_pm fimd device state on probe
drm/exynos: use correct 'exynos-drm' name for platform device
drm/i915: support 32 bit BGR formats in sprite planes
drm/i915: fix color order for BGR formats on SNB
drm/gma500: Fix Cedarview boot failures in 3.3-rc
Pull media fixes from Mauro Carvalho Chehab:
"For 4 fixes for 3.3 (all trivial):
- uvc video driver: fixes a division by zero;
- davinci: add module.h to fix compilation;
- smsusb: fix the delivery system setting;
- smsdvb: the get_frontend implementation there is broken.
The smsdvb patch has 127 lines, but it is trivial: instead of
returning a cache of the set_frontend (with is wrong, as it doesn't
have the updated values for the data, and the implementation there is
buggy), it copies the information of the detected DVB parameters from
the smsdvb private structures into the corresponding DVBv5 struct
fields."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] smsdvb: fix get_frontend
[media] smsusb: fix the default delivery system setting
[media] media: davinci: added module.h to resolve unresolved macros
[media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation
Pull target fixes from Nicholas Bellinger:
"This series addresses two recently reported regression bugs related to
legacy SCSI reservation usage in target core, and iscsi-target
reservation conflict handling.
The second patch in particular addresses possible data-corruption with
SCSI reservations that is specific to iscsi-target fabric LUNs with
multiple client writers. Both patches need to go into v3.2 stable
ASAP, and the branch based on the last target-pending/3.3-rc-fixes
HEAD.
Again, thanks to Martin Svec for his help to identify and address this
regression bug with iscsi-target."
* '3.3-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix reservation conflict -EBUSY response handling bug
target: Fix compatible reservation handling (CRH=1) with legacy RESERVE/RELEASE
strict_strtoul() writes a long but ->gamma_mode only has space to store an
int, so on 64 bit systems we end up scribbling over ->gamma_table_count as
well. I've changed it to use kstrtouint() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'd like to add Inki Dae, Donghwa Lee and Kyungmin Park as maintainers
who developers for exynos mipi display drivers for
video/driver/exynos/exynos_mipi* and include/video/exynos_mipi*.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gustavo's tree is called just bluetooth.git and not bluetooth-2.6.git
anymore.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been coordinating Bluetooth patches in my tree for some time and
it's possible I'll do it in the future too, so add myself to the
Bluetooth sections as well as mention my tree there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is going to be the primary e-mail for kernel development.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
