Variable 'ret' is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant assignment
and can be removed.
Clean up the following clang-analyzer warning:
drivers/infiniband/hw/qib/qib_sd7220.c:690:2: warning: Value stored to
'ret' is never read [clang-analyzer-deadcode.DeadStores]
Link: https://lore.kernel.org/r/1619692940-104771-1-git-send-email-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The new attribute indicates that the kernel copies DMA pages on fork,
hence libibverbs' fork support through madvise and MADV_DONTFORK is not
needed.
The introduced attribute is always reported as supported since the kernel
has the patch that added the copy-on-fork behavior. This allows the
userspace library to identify older vs newer kernel versions. Extra care
should be taken when backporting this patch as it relies on the fact that
the copy-on-fork patch is merged, hence no check for support is added.
Don't backport this patch unless you also have the following series:
commit 70e806e4e6 ("mm: Do early cow for pinned pages during fork() for
ptes") and commit 4eae4efa2c ("hugetlb: do early cow when page pinned on
src mm").
Fixes: 70e806e4e6 ("mm: Do early cow for pinned pages during fork() for ptes")
Fixes: 4eae4efa2c ("hugetlb: do early cow when page pinned on src mm")
Link: https://lore.kernel.org/r/20210418121025.66849-1-galpress@amazon.com
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In bnxt_qplib_alloc_res, it calls bnxt_qplib_alloc_dpi_tbl(). Inside
bnxt_qplib_alloc_dpi_tbl, dpit->dbr_bar_reg_iomem is freed via
pci_iounmap() in unmap_io error branch. After the callee returns err code,
bnxt_qplib_alloc_res calls
bnxt_qplib_free_res()->bnxt_qplib_free_dpi_tbl() in the fail branch. Then
dpit->dbr_bar_reg_iomem is freed in the second time by pci_iounmap().
My patch set dpit->dbr_bar_reg_iomem to NULL after it is freed by
pci_iounmap() in the first time, to avoid the double free.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/20210426140614.6722-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Our code analyzer reported a UAF.
In siw_alloc_mr(), it calls siw_mr_add_mem(mr,..). In the implementation of
siw_mr_add_mem(), mem is assigned to mr->mem and then mem is freed via
kfree(mem) if xa_alloc_cyclic() failed. Here, mr->mem still point to a
freed object. After, the execution continue up to the err_out branch of
siw_alloc_mr, and the freed mr->mem is used in siw_mr_drop_mem(mr).
My patch moves "mr->mem = mem" behind the if (xa_alloc_cyclic(..)<0) {}
section, to avoid the uaf.
Fixes: 2251334dca ("rdma/siw: application buffer management")
Link: https://lore.kernel.org/r/20210426011647.3561-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Bernard Metzler <bmt@zurich.ihm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The variable rcd is being assigned a value from a calculation however the
variable is never read, so this redundant variable can be removed.
Cleans up the following clang-analyzer warning:
drivers/infiniband/hw/hfi1/affinity.c:986:3: warning: Value stored to
'rcd' is never read [clang-analyzer-deadcode.DeadStores].
Link: https://lore.kernel.org/r/1619346696-46300-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add QP numbers that are associated with the SRQ to the SRQ information.
The QPs are displayed in a range form.
Sample output:
$ rdma res show srq
dev ibp8s0f0 srqn 0 type BASIC pdn 3 comm [ib_ipoib]
dev ibp8s0f0 srqn 4 type BASIC lqpn 125-128,130-140 pdn 9 pid 3581 comm ibv_srq_pingpon
dev ibp8s0f0 srqn 5 type BASIC lqpn 141-156 pdn 10 pid 3584 comm ibv_srq_pingpon
dev ibp8s0f0 srqn 6 type BASIC lqpn 157-172 pdn 11 pid 3590 comm ibv_srq_pingpon
dev ibp8s0f1 srqn 0 type BASIC pdn 3 comm [ib_ipoib]
dev ibp8s0f1 srqn 1 type BASIC lqpn 329-344 pdn 4 pid 3586 comm ibv_srq_pingpon
$ rdma res show srq lqpn 126-141
dev ibp8s0f0 srqn 4 type BASIC lqpn 126-128,130-140 pdn 9 pid 3581 comm ibv_srq_pingpon
dev ibp8s0f0 srqn 5 type BASIC lqpn 141 pdn 10 pid 3584 comm ibv_srq_pingpon
$ rdma res show srq lqpn 127
dev ibp8s0f0 srqn 4 type BASIC lqpn 127 pdn 9 pid 3581 comm ibv_srq_pingpon
Link: https://lore.kernel.org/r/79a4bd4caec2248fd9583cccc26786af8e4414fc.1618753110.git.leonro@nvidia.com
Signed-off-by: Neta Ostrovsky <netao@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Extend the RDMA nldev return a SRQ information, like SRQ number, SRQ type,
PD number, CQ number and process ID that created that SRQ.
Sample output:
$ rdma res show srq
dev ibp8s0f0 srqn 0 type BASIC pdn 3 comm [ib_ipoib]
dev ibp8s0f0 srqn 4 type BASIC pdn 9 pid 3581 comm ibv_srq_pingpon
dev ibp8s0f0 srqn 5 type BASIC pdn 10 pid 3584 comm ibv_srq_pingpon
dev ibp8s0f0 srqn 6 type BASIC pdn 11 pid 3590 comm ibv_srq_pingpon
dev ibp8s0f1 srqn 0 type BASIC pdn 3 comm [ib_ipoib]
dev ibp8s0f1 srqn 1 type BASIC pdn 4 pid 3586 comm ibv_srq_pingpon
Link: https://lore.kernel.org/r/322f9210b95812799190dd4a0fb92f3a3bba0333.1618753110.git.leonro@nvidia.com
Signed-off-by: Neta Ostrovsky <netao@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In order to track SRQ resources, a new restrack object is initialized and
added to the resource tracking database.
Link: https://lore.kernel.org/r/0db71c409f24f2f6b019bf8797a8fed96fe7079c.1618753110.git.leonro@nvidia.com
Signed-off-by: Neta Ostrovsky <netao@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Extend the RDMA nldev return a context information, like ctx number and
process ID that created that context. This functionality is helpful to
find orphan contexts that are not closed for some reason.
Sample output:
$ rdma res show ctx
dev ibp8s0f0 ctxn 0 pid 980 comm ibv_rc_pingpong
dev ibp8s0f0 ctxn 1 pid 981 comm ibv_rc_pingpong
dev ibp8s0f0 ctxn 2 pid 992 comm ibv_rc_pingpong
dev ibp8s0f1 ctxn 0 pid 984 comm ibv_rc_pingpong
dev ibp8s0f1 ctxn 1 pid 987 comm ibv_rc_pingpong
$ rdma res show ctx dev ibp8s0f1
dev ibp8s0f1 ctxn 0 pid 984 comm ibv_rc_pingpong
dev ibp8s0f1 ctxn 1 pid 987 comm ibv_rc_pingpong
Link: https://lore.kernel.org/r/5c956acfeac4e9d532988575f3da7d64cb449374.1618753110.git.leonro@nvidia.com
Signed-off-by: Neta Ostrovsky <netao@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The device attach triggers addition of CM_ID to the restrack DB.
However, when error occurs, we releasing this device, but defer CM_ID
release. This causes to the situation where restrack sees CM_ID that
is not valid anymore.
As a solution, add the CM_ID to the resource tracking DB only after the
attachment is finished.
Found by syzcaller:
infiniband syz0: added syz_tun
rdma_rxe: ignoring netdev event = 10 for syz_tun
infiniband syz0: set down
infiniband syz0: ib_query_port failed (-19)
restrack: ------------[ cut here ]------------
infiniband syz0: BUG: RESTRACK detected leak of resources
restrack: User CM_ID object allocated by syz-executor716 is not freed
restrack: ------------[ cut here ]------------
Fixes: b09c4d7012 ("RDMA/restrack: Improve readability in task name management")
Link: https://lore.kernel.org/r/ab93e56ba831eac65c322b3256796fa1589ec0bb.1618753862.git.leonro@nvidia.com
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
A switchdev RDMA device do not support IB CM. When such device is added to
the RDMA CM's device list, when application invokes rdma_listen(), cma
attempts to listen to such device, however it has IB CM attribute
disabled.
Due to this, rdma_listen() call fails to listen for other non switchdev
devices as well.
A below error message can be seen.
infiniband mlx5_0: RDMA CMA: cma_listen_on_dev, error -38
A failing call flow is below.
cma_listen_on_all()
cma_listen_on_dev()
_cma_attach_to_dev()
rdma_listen() <- fails on a specific switchdev device
This is because rdma_listen() is hardwired to only work with iwarp or IB
CM compatible devices.
Hence, when a IB device doesn't support IB CM or IW CM, avoid adding such
device to the cma list so rdma_listen() can't even be called.
Link: https://lore.kernel.org/r/f9cac00d52864ea7c61295e43fb64cf4db4fdae6.1618753862.git.leonro@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix a bug in rxe_fill_ip_info() which was attempting to convert from
RDMA_NETWORK_XXX to RXE_NETWORK_XXX. .._IPV6 should have mapped to .._IPV6
not .._IPV4.
Fixes: edebc8407b ("RDMA/rxe: Fix small problem in network_type patch")
Link: https://lore.kernel.org/r/20210421035952.4892-1-rpearson@hpe.com
Suggested-by: Frank Zago <frank.zago@hpe.com>
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Expose a non standard query port via IOCTL that will be used to expose
port attributes that are specific to mlx5 devices.
The new interface receives a port number to query and returns a structure
that contains the available attributes for that port. This will be used
to fill the gap between pure DEVX use cases and use cases where a kernel
needs to inform userspace about various kernel driver configurations that
userspace must use in order to work correctly.
Flags is used to indicate which fields are valid on return.
MLX5_IB_UAPI_QUERY_PORT_VPORT:
The vport number of the queered port.
MLX5_IB_UAPI_QUERY_PORT_VPORT_VHCA_ID:
The VHCA ID of the vport of the queered port.
MLX5_IB_UAPI_QUERY_PORT_VPORT_STEERING_ICM_RX:
The vport's RX ICM address used for sw steering.
MLX5_IB_UAPI_QUERY_PORT_VPORT_STEERING_ICM_TX:
The vport's TX ICM address used for sw steering.
MLX5_IB_UAPI_QUERY_PORT_VPORT_REG_C0:
The metadata used to tag egress packets of the vport.
MLX5_IB_UAPI_QUERY_PORT_ESW_OWNER_VHCA_ID:
The E-Switch owner vhca id of the vport.
Link: https://lore.kernel.org/r/6e2ef13e5a266a6c037eb0105eb1564c7bb52f23.1618743394.git.leonro@nvidia.com
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently when GID is deleted, it zero out all the fields of the RoCE
address in the SET_ROCE_ADDRESS command for a specified index.
roce_version = 0 means RoCEv1 in the SET_ROCE_ADDRESS command.
This assumes that device has RoCEv1 always enabled which is not always
correct. For example Subfunction does not support RoCEv1.
Due to this assumption a previously added RoCEv2 GID is always deleted as
RoCEv1 GID. This results in a below syndrome:
mlx5_core.sf mlx5_core.sf.4: mlx5_cmd_check:777:(pid 4256): SET_ROCE_ADDRESS(0x761) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x12822d)
Hence set the right RoCE version during GID deletion provided by the core.
Link: https://lore.kernel.org/r/d3f54129c90ca329caf438dbe31875d8ad08d91a.1618753425.git.leonro@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When i40iw_hmc_sd_one fails, chunk is freed without the deletion of chunk
entry in the PBLE info list.
Fix it by adding the chunk entry to the PBLE info list only after
successful addition of SD in i40iw_hmc_sd_one.
This fixes a static checker warning reported here:
https://lore.kernel.org/linux-rdma/YHV4CFXzqTm23AOZ@mwanda/
Fixes: 9715830157 ("i40iw: add pble resource files")
Link: https://lore.kernel.org/r/20210416002104.323-1-shiraz.saleem@intel.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
missing qpid increment leads to skipping few qpids while allocating QP.
This eventually leads to adapter running out of qpids after establishing
fewer connections than it actually supports.
Current patch increments the qpid correctly.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Link: https://lore.kernel.org/r/20210415151422.9139-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
struct ipoib_cm_tx is defined at 245th line. And the definition is
independent on the MACRO. The declaration here is unnecessary. Remove it.
Link: https://lore.kernel.org/r/20210415092124.27684-1-wanjiabing@vivo.com
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Instead of manually messing with parent driver module reference counting
rely on export symbol mechanism to ensure that proper probe/remove chain
is performed.
Link: https://lore.kernel.org/r/20210401065715.565226-4-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-By: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Convert indirect probe call to its direct equivalent to create a symbol
link between RDMA and netdev modules. This will give us an ability to
remove custom module reference counting that doesn't belong to the driver.
Link: https://lore.kernel.org/r/20210401065715.565226-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-By: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The "select" kconfig keyword provides reverse dependency, however it
doesn't check that selected symbol meets its own dependencies. Usually
"select" is used for non-visible symbols, so instead of trying to keep
dependencies in sync with BNXT ethernet driver, simply "depends on" it,
like Kconfig documentation suggest.
* CONFIG_PCI is already required by BNXT
* CONFIG_NETDEVICES and CONFIG_ETHERNET are needed to chose BNXT
Link: https://lore.kernel.org/r/20210401065715.565226-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-By: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently IPoIB connected mode queries the device to get the pkey table
entry during connection formation. This will increase the time taken to
form the connection, especially when limited pkeys are in use. This gets
worse when multiple connection attempts are done in parallel.
Since ipoib interfaces are locked to a single pkey, use the pkey index
that was determined at link up time instead of searching for anything.
This improved the latency from 500ms to 1ms on an internal setup.
Link: https://lore.kernel.org/r/1618338965-16717-1-git-send-email-manjunath.b.patil@oracle.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In cm_req_handler(), unify the check for RoCE and re-factor to avoid
one test.
Link: https://lore.kernel.org/r/1617705423-15570-1-git-send-email-haakon.bugge@oracle.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: 8f97486024 ("IB/cm: Reduce dependency on gid attribute ndev check")
Fixes: 194f64a3ca ("RDMA/core: Fix corrupted SL on passive side")
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When "enhanced IPoIB" is enabled for CX-5 devices it requires the parent
device to be UP, otherwise the child devices won't work.
Thus add a debug message to give admin a hint when only the child
interface is UP but parent interface is not.
Link: https://lore.kernel.org/r/20210408093215.24023-1-jinpu.wang@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Introduce the VF support by adding code changes to allow VF PCI device
initialization, assgining the reserved resource of the PF to the active
VFs, setting the default abilities, applying the interruptions, resetting
and reducing the default QP/GID number to aovid exceeding the hardware
limitation.
Link: https://lore.kernel.org/r/1617715514-29039-6-git-send-email-liweihang@huawei.com
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Shengming Shu <shushengming1@huawei.com>
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Switch parameters of all functions belong to a PF should be set including
VFs.
Link: https://lore.kernel.org/r/1617715514-29039-5-git-send-email-liweihang@huawei.com
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Shengming Shu <shushengming1@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Query the resource including EQC/SMAC/SGID from the firmware in the PF and
distribute fairly among all the functions belong to the PF.
Link: https://lore.kernel.org/r/1617715514-29039-4-git-send-email-liweihang@huawei.com
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Shengming Shu <shushengming1@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Query how many functions are supported by the PF from the FW and store it
in the hns_roce_dev structure which will be used to support the
configuration of virtual functions.
Link: https://lore.kernel.org/r/1617715514-29039-3-git-send-email-liweihang@huawei.com
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Shengming Shu <shushengming1@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use hr_reg_write/read() to simplify codes about configuring function's
resource. And because the design of PF/VF fields is same, they can be
defined only once.
Link: https://lore.kernel.org/r/1617715514-29039-2-git-send-email-liweihang@huawei.com
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Two error messages are only different message but have common
code to generate the path string.
Link: https://lore.kernel.org/r/20210406123639.202899-4-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It does not help to debug if it only print error message
without any debugging information which session and connection
the error happened.
Link: https://lore.kernel.org/r/20210406123639.202899-3-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Client prints only error value and it is not enough for debugging.
1. When client receives an error from server: the client does not only
print the error value but also more information of server connection.
2. When client failes to send IO: the client gets an error from RDMA
layer. It also print more information of server connection.
Link: https://lore.kernel.org/r/20210406123639.202899-2-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Describe new multipath policy min-latency of the RTRS client.
Link: https://lore.kernel.org/r/20210407113444.150961-5-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It shows the latest latency that the client checked when sending the
heart-beat.
Link: https://lore.kernel.org/r/20210407113444.150961-3-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This patch adds new multipath policy: min-latency. Client checks the
latency of each path when it sends the heart-beat. And it sends IO to the
path with the minimum latency.
Link: https://lore.kernel.org/r/20210407113444.150961-2-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Maor Gottlieb says:
====================
This series from Maor extends MEMIC to support atomic operations from the
host in addition to already supported regular read/write.
====================
* 'memic_ops':
RDMA/mlx5: Expose UAPI to query DM
RDMA/mlx5: Add support in MEMIC operations
RDMA/mlx5: Add support to MODIFY_MEMIC command
RDMA/mlx5: Re-organize the DM code
RDMA/mlx5: Move all DM logic to separate file
RDMA/uverbs: Make UVERBS_OBJECT_METHODS to consider line number
net/mlx5: Add MEMIC operations related bits
Expose UAPI to query MEMIC DM, this will let user space application
that didn't allocate the DM but has access to by owning the matching
command FD to retrieve its information.
Link: https://lore.kernel.org/r/20210411122924.60230-8-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
MEMIC buffer, in addition to regular read and write operations, can
support atomic operations from the host.
Introduce and implement new UAPI to allocate address space for MEMIC
operations such as atomic. This includes:
1. Expose new IOCTL for request mapping of MEMIC operation.
2. Hold the operations address in a list, so same operation to same DM
will be allocated only once.
3. Manage refcount on the mlx5_ib_dm object, so it would be keep valid
until all addresses were unmapped.
Link: https://lore.kernel.org/r/20210411122924.60230-7-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add two functions to allocate and deallocate MEMIC operations
by using the MODIFY_MEMIC command.
Link: https://lore.kernel.org/r/20210411122924.60230-6-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
1. Inline the checks from check_dm_type_support() into their
respective allocation functions.
2. Fix use after free when driver fails to copy the MEMIC address to the
user by moving the allocation code into their respective functions,
hence we avoid the explicit call to free the DM in the error flow.
3. Split mlx5_ib_dm struct to memic and icm proper typesafety
throughout.
Fixes: dc2316eba7 ("IB/mlx5: Fix device memory flows")
Link: https://lore.kernel.org/r/20210411122924.60230-5-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Move all device memory related code to a separate file.
Link: https://lore.kernel.org/r/20210411122924.60230-4-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In order to support multiple methods declaration in the same file we
should use the line number as part of the name.
Link: https://lore.kernel.org/r/20210411122924.60230-3-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add the MEMIC operations bits and structures to the mlx5_ifc file.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
All other users of the dummy netdevice embed the netdev in other
structures:
init_dummy_netdev(&mal->dummy_dev);
init_dummy_netdev(ð->dummy_dev);
init_dummy_netdev(&ar->napi_dev);
init_dummy_netdev(&irq_grp->napi_ndev);
init_dummy_netdev(&wil->napi_ndev);
init_dummy_netdev(&trans_pcie->napi_dev);
init_dummy_netdev(&dev->napi_dev);
init_dummy_netdev(&bus->mux_dev);
The AIP and VNIC implementation turns that model inside out and used a
kfree() to free what appears to be a netdev struct when in reality, it is
a struct that enbodies the rx state as well as the dummy netdev used to
support napi_poll across disparate receive contexts. The relationship is
infered by the odd allocation:
const int netdev_size = sizeof(*dd->dummy_netdev) +
sizeof(struct hfi1_netdev_priv);
<snip>
dd->dummy_netdev = kcalloc_node(1, netdev_size, GFP_KERNEL, dd->node);
Correct the issue by:
- Correctly naming the alloc and free functions
- Renaming hfi1_netdev_priv to hfi1_netdev_rx
- Replacing dd dummy_netdev with a netdev_rx pointer
- Embedding the net_device in hfi1_netdev_rx
- Moving the init_dummy_netdev to the alloc routine
- Adjusting wrappers to fit the new model
Fixes: 6991abcb99 ("IB/hfi1: Add functions to receive accelerated ipoib packets")
Link: https://lore.kernel.org/r/1617026056-50483-11-git-send-email-dennis.dalessandro@cornelisnetworks.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
As a flush operation is implemented inside destroy_workqueue(), there is
no need to do flush operation before.
Fixes: bfcc681bd0 ("IB/hns: Fix the bug when free mr")
Fixes: 0425e3e6e0 ("RDMA/hns: Support flush cqe for hip08 in kernel space")
Link: https://lore.kernel.org/r/1618305087-30799-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
A session can be removed dynamically by sysfs interface "remove_path" that
eventually calls rtrs_clt_remove_path_from_sysfs function. The current
rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and
frees sess->stats object. Second it removes the session from the active
list.
Therefore some functions could access non-connected session and access the
freed sess->stats object even-if they check the session status before
accessing the session.
For instance rtrs_clt_request and get_next_path_min_inflight check the
session status and try to send IO to the session. The session status
could be changed when they are trying to send IO but they could not catch
the change and update the statistics information in sess->stats object,
and generate use-after-free problem.
(see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its
stats")
This patch changes the rtrs_clt_remove_path_from_sysfs to remove the
session from the active session list and then destroy the sysfs
interfaces.
Each function still should check the session status because closing or
error recovery paths can change the status.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20210412084002.33582-1-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: db7683d7de ("IB/srpt: Fix login-related race conditions")
Link: https://lore.kernel.org/r/20210408113132.87250-1-wangwensheng4@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
