Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e0 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: firmware message delay fixes.
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
-----BEGIN PGP SIGNATURE-----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=JEqH
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev says:
====================
nic: thunderx: fix communication races between VF & PF
The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.
After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.
Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.
This patch series is to address race condition with VF & PF communication.
Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
from int to void;
- 0007: update subject and remove unused variable 'netdev'
from nicvf_link_status_check_task() function;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.
This commit is to change the xcast message structure in order to
fit it into 64 bit.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct STREERING to STEERING at macro name for BGX steering register.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e05 ("team: account for oper state")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
* Spawn container & change ipvlan mode setting inside of it:
# docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf
9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bd ("sctp: avoid refreshing heartbeat timer too often")
Reported-by: Marcin Stojek <marcin.stojek@nokia.com>
Tested-by: Marcin Stojek <marcin.stojek@nokia.com>
Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.
So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
clang warns about overflowing the data[] member in the struct pnpipehdr:
net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds]
if (hdr->data[4] == PEP_IND_READY)
^ ~
include/net/phonet/pep.h:66:3: note: array 'data' declared here
u8 data[1];
Using a flexible array member at the end of the struct avoids the
warning, but since we cannot have a flexible array member inside
of the union, each index now has to be moved back by one, which
makes it a little uglier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-02-21
1) Don't do TX bytes accounting for the esp trailer when sending
from a request socket as this will result in an out of bounds
memory write. From Martin Willi.
2) Destroy xfrm_state synchronously on net exit path to
avoid nested gc flush callbacks that may trigger a
warning in xfrm6_tunnel_net_exit(). From Cong Wang.
3) Do an unconditionally clone in pfkey_broadcast_one()
to avoid a race when freeing the skb.
From Sean Tranchetti.
4) Fix inbound traffic via XFRM interfaces across network
namespaces. We did the lookup for interfaces and policies
in the wrong namespace. From Tobias Brunner.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
report erspan version field just for erspan tunnels
Do not report erspan_version to userpsace for non erspan tunnels.
Report IFLA_GRE_ERSPAN_INDEX only for erspan version 1 in
ip6gre_fill_info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Report erspan version field to userspace in ip6gre_fill_info just for
erspan_v6 tunnels. Moreover report IFLA_GRE_ERSPAN_INDEX only for
erspan version 1.
The issue can be triggered with the following reproducer:
$ip link add name gre6 type ip6gre local 2001::1 remote 2002::2
$ip link set gre6 up
$ip -d link sh gre6
14: grep6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1448 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre6 2001::1 peer 2002::2 promiscuity 0 minmtu 0 maxmtu 0
ip6gre remote 2002::2 local 2001::1 hoplimit 64 encaplimit 4 tclass 0x00 flowlabel 0x00000 erspan_index 0 erspan_ver 0 addrgenmode eui64
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report erspan version field to userspace in ipgre_fill_info just for
erspan tunnels. The issue can be triggered with the following reproducer:
$ip link add name gre1 type gre local 192.168.0.1 remote 192.168.1.1
$ip link set dev gre1 up
$ip -d link sh gre1
13: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre 192.168.0.1 peer 192.168.1.1 promiscuity 0 minmtu 0 maxmtu 0
gre remote 192.168.1.1 local 192.168.0.1 ttl inherit erspan_ver 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.
But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.
Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.
Exclude callers for which network header offset is not known.
Fixes: d5be7f632b ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tung Nguyen says:
====================
tipc: improvement for wait and wakeup
Some improvements for tipc_wait_for_xzy().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6f bonding: pass link-local packets to bonding master also.
... to:
b89f04c61e bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6f restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6f (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similiar to commit e94cd8113c ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The listed address for the CAIF maintainer bounces with
"553 5.3.0 <dmitry.tarnyagin@lockless.no>... No such user here", and the
only existing email address of the maintainer in git history hasn't
responded in a week.
Therefore, remove the listed maintainer and mark CAIF as orphan.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-02-21
This series contains fixes to ixgbe and i40e.
Majority of the fixes are to resolve XDP issues found in both drivers,
there is only one fix which is not XDP related. That one fix resolves
an issue seen on older 10GbE devices, where UDP traffic was either being
dropped or being transmitted out of order when the bit to enable L3/L4
filtering for transmit switched packets is enabled on older devices that
did not support this option.
Magnus fixes an XDP issue for both ixgbe and i40e, where receive rings
are created but no buffers are allocated for AF_XDP in zero-copy mode,
so no packets can be received and no interrupts will be generated so
that NAPI poll function that allocates buffers to the rings will never
get executed.
Björn fixes a race in XDP xmit ring cleanup for i40e, where
ndo_xdp_xmit() must be taken into consideration. Added a
synchronize_rcu() to wait for napi(s) before clearing the queue.
Jan fixes a ixgbe AF_XDP zero-copy transmit issue which can cause a
reset to be triggered, so add a check to ensure that netif carrier is
'ok' before trying to transmit packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue has been found while testing zero-copy XDP that
causes a reset to be triggered. As it takes some time to
turn the carrier on after setting zc, and we already
start trying to transmit some packets, watchdog considers
this as an erroneous state and triggers a reset.
Don't do any work if netif carrier is not OK.
Fixes: 8221c5eba8 (ixgbe: add AF_XDP zero-copy Tx support)
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the RX rings are created they are also populated with buffers so
that packets can be received. Usually these are kernel buffers, but
for AF_XDP in zero-copy mode, these are user-space buffers and in this
case the application might not have sent down any buffers to the
driver at this point. And if no buffers are allocated at ring creation
time, no packets can be received and no interrupts will be generated so
the NAPI poll function that allocates buffers to the rings will never
get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once after
an XDP program has loaded and once after the umem is registered. This
take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The enabling L3/L4 filtering for transmit switched packets for all
devices caused unforeseen issue on older devices when trying to send UDP
traffic in an ordered sequence. This bit was originally intended for X550
devices, which supported this feature, so limit the scope of this bit to
only X550 devices.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
smc_poll() returns with mask bit EPOLLPRI if the connection urg_state
is SMC_URG_VALID. Since SMC_URG_VALID is zero, smc_poll signals
EPOLLPRI errorneously if called in state SMC_INIT before the connection
is created, for instance in a non-blocking connect scenario.
This patch switches to non-zero values for the urg states.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Fixes: de8474eb9d ("net/smc: urgent data support")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
ipv6: route: enforce RCU protection for fib6_info->from
This series addresses a couple of RCU left-over dating back to rt6_info->from
conversion to RCU
v1 -> v2:
- fix a possible race in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a RCU critical section around rt6_info->from deference, and
proper annotation.
Fixes: 4ed591c8ab ("net/ipv6: Allow onlink routes to have a device mismatch if it is the default route")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must access rt6_info->from under RCU read lock: move the
dereference under such lock, with proper annotation.
v1 -> v2:
- avoid using multiple, racy, fetch operations for rt->from
Fixes: a68886a691 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several u->addr and u->path users are not holding any locks in
common with unix_bind(). unix_state_lock() is useless for those
purposes.
u->addr is assign-once and *(u->addr) is fully set up by the time
we set u->addr (all under unix_table_lock). u->path is also
set in the same critical area, also before setting u->addr, and
any unix_sock with ->path filled will have non-NULL ->addr.
So setting ->addr with smp_store_release() is all we need for those
"lockless" users - just have them fetch ->addr with smp_load_acquire()
and don't even bother looking at ->path if they see NULL ->addr.
Users of ->addr and ->path fall into several classes now:
1) ones that do smp_load_acquire(u->addr) and access *(u->addr)
and u->path only if smp_load_acquire() has returned non-NULL.
2) places holding unix_table_lock. These are guaranteed that
*(u->addr) is seen fully initialized. If unix_sock is in one of the
"bound" chains, so's ->path.
3) unix_sock_destructor() using ->addr is safe. All places
that set u->addr are guaranteed to have seen all stores *(u->addr)
while holding a reference to u and unix_sock_destructor() is called
when (atomic) refcount hits zero.
4) unix_release_sock() using ->path is safe. unix_bind()
is serialized wrt unix_release() (normally - by struct file
refcount), and for the instances that had ->path set by unix_bind()
unix_release_sock() comes from unix_release(), so they are fine.
Instances that had it set in unix_stream_connect() either end up
attached to a socket (in unix_accept()), in which case the call
chain to unix_release_sock() and serialization are the same as in
the previous case, or they never get accept'ed and unix_release_sock()
is called when the listener is shut down and its queue gets purged.
In that case the listener's queue lock provides the barriers needed -
unix_stream_connect() shoves our unix_sock into listener's queue
under that lock right after having set ->path and eventual
unix_release_sock() caller picks them from that queue under the
same lock right before calling unix_release_sock().
5) unix_find_other() use of ->path is pointless, but safe -
it happens with successful lookup by (abstract) name, so ->path.dentry
is guaranteed to be NULL there.
earlier-variant-reviewed-by: "Paul E. McKenney" <paulmck@linux.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Booting 4.20 on SolidRun Clearfog issues this warning with DMA API
debug enabled:
WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc
mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes]
Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables
CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14)
[<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4)
[<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124)
[<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48)
[<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc)
[<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74)
[<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58)
[<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424)
[<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540)
[<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144)
[<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0)
[<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98)
[<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98)
...
This appears to be caused by mvneta_rx_hwbm() calling
dma_sync_single_range_for_cpu() with the wrong struct device pointer,
as the buffer manager device pointer is used to map and unmap the
buffer. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
