commit ba18a9314a ("Revert "HID: i2c-hid: Add support for ACPI GPIO
interrupts"") removed the need for storing the irq in struct i2c_hid.
But then commit de3c99488609 ("HID: i2c-hid: Disable IRQ before freeing
buffers") forgot to update the location of the irq.
Fix this by using the actual I2C client irq.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a forgotten include that I've by mistake omitted when resolving
merge conflict in ead0687fe30 ("HID: i2c-hid: support regulator power
on/off").
Fixes: ead0687fe30 ("HID: i2c-hid: support regulator power on/off")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID report buffers that are initially allocated on i2c_hid_probe()
might not be big enough to hold the HID reports from a specific device,
in which case they will be freed and new ones will be allocated in
i2c_hid_start(), at point which the device's report size is known. But
at this point ihid->irq is already running, and may call
i2c_hid_get_input() which passes ihid->inbuf to i2c_master_recv(). Since
this handler runs in a separate thread, ihid->inbuf may be freed at this
very moment, and i2c_master_recv() will write on memory which may be
already owned by a different part of the kernel, corrupting its data.
This problem has been observed on an Asus UX360UA laptop which has an
I2C touchpad, and results in a complete system freeze or an unusable
slowness with a lof of "BUG: unable to handle kernel paging request at
<address>" warnings. Enabling SLUB debugging shows a use-after-free
warning on memory allocated in i2c_hid_alloc_buffers() and freed in
i2c_hid_free_buffers():
=============================================================================
BUG kmalloc-64 (Not tainted): Poison overwritten
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: 0xffff880264083273-0xffff88026408329e. first byte 0x0 instead of 0x6b
INFO: Allocated in i2c_hid_alloc_buffers+0x25/0xa0 [i2c_hid] age=35793 cpu=2 pid=430
___slab_alloc+0x41e/0x460
__slab_alloc+0x20/0x40
__kmalloc+0x210/0x280
i2c_hid_alloc_buffers+0x25/0xa0 [i2c_hid]
i2c_hid_probe+0x12f/0x5e0 [i2c_hid]
i2c_device_probe+0x10a/0x1b0
driver_probe_device+0x220/0x4a0
__device_attach_driver+0x71/0xa0
bus_for_each_drv+0x67/0xb0
__device_attach+0xdc/0x170
device_initial_probe+0x13/0x20
bus_probe_device+0x92/0xa0
device_add+0x4aa/0x670
device_register+0x1a/0x20
i2c_new_device+0x18e/0x230
acpi_i2c_add_device+0x1a0/0x210
INFO: Freed in i2c_hid_free_buffers+0x16/0x60 [i2c_hid] age=7552 cpu=1 pid=1473
__slab_free+0x221/0x330
kfree+0x139/0x160
i2c_hid_free_buffers+0x16/0x60 [i2c_hid]
i2c_hid_start+0x2a9/0x2df [i2c_hid]
mt_probe+0x160/0x22e [hid_multitouch]
hid_device_probe+0xd7/0x150 [hid]
driver_probe_device+0x220/0x4a0
__driver_attach+0x84/0x90
bus_for_each_dev+0x6c/0xc0
driver_attach+0x1e/0x20
bus_add_driver+0x1c3/0x280
driver_register+0x60/0xe0
__hid_register_driver+0x53/0x90 [hid]
0xffffffffc004f01e
do_one_initcall+0xb3/0x1f0
do_init_module+0x5f/0x1d0
INFO: Slab 0xffffea0009902080 objects=20 used=20 fp=0x (null) flags=0x17fff8000004080
INFO: Object 0xffff880264083260 @offset=4704 fp=0x (null)
Bytes b4 ffff880264083250: 8d e6 fe ff 00 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a ........ZZZZZZZZ
Object ffff880264083260: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object ffff880264083270: 6b 6b 6b 00 00 00 00 00 00 00 00 00 00 00 00 00 kkk.............
Object ffff880264083280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff880264083290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Redzone ffff8802640832a0: bb bb bb bb bb bb bb bb ........
Padding ffff8802640833e0: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 1 PID: 1503 Comm: python3 Tainted: G B 4.4.21+ #10
Hardware name: ASUSTeK COMPUTER INC. UX360UA/UX360UA, BIOS UX360UA.200 05/05/2016
0000000000000086 00000000622d48a2 ffff88026061ba38 ffffffff813f6044
ffff880264082010 ffff880264083260 ffff88026061ba78 ffffffff811e8eab
0000000000000008 ffff880200000001 ffff88026408329f ffff88026a007700
Call Trace:
[<ffffffff813f6044>] dump_stack+0x63/0x8f
[<ffffffff811e8eab>] print_trailer+0x14b/0x1f0
[<ffffffff811e94c1>] check_bytes_and_report+0xc1/0x100
[<ffffffff811e96c4>] check_object+0x1c4/0x240
[<ffffffff81293fde>] ? ext4_htree_store_dirent+0x3e/0x120
[<ffffffff811e9b44>] alloc_debug_processing+0x104/0x180
[<ffffffff811eb7be>] ___slab_alloc+0x41e/0x460
[<ffffffff81293fde>] ? ext4_htree_store_dirent+0x3e/0x120
[<ffffffff8124590b>] ? __getblk_gfp+0x2b/0x60
[<ffffffff8129b969>] ? ext4_getblk+0xa9/0x190
[<ffffffff811eb820>] __slab_alloc+0x20/0x40
[<ffffffff811ed320>] __kmalloc+0x210/0x280
[<ffffffff81293fde>] ? ext4_htree_store_dirent+0x3e/0x120
[<ffffffff812c1602>] ? ext4fs_dirhash+0xc2/0x2a0
[<ffffffff81293fde>] ext4_htree_store_dirent+0x3e/0x120
[<ffffffff812a4f47>] htree_dirblock_to_tree+0x187/0x1b0
[<ffffffff812a5fd2>] ext4_htree_fill_tree+0xb2/0x2e0
[<ffffffff811ebb7a>] ? kmem_cache_alloc_trace+0x1fa/0x220
[<ffffffff81293e45>] ? ext4_readdir+0x775/0x8b0
[<ffffffff81293cb1>] ext4_readdir+0x5e1/0x8b0
[<ffffffff81221c82>] iterate_dir+0x92/0x120
[<ffffffff81222118>] SyS_getdents+0x98/0x110
[<ffffffff81221d10>] ? iterate_dir+0x120/0x120
[<ffffffff818157f2>] entry_SYSCALL_64_fastpath+0x16/0x71
FIX kmalloc-64: Restoring 0xffff880264083273-0xffff88026408329e=0x6b
FIX kmalloc-64: Marking all objects used
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Function hid_post_reset() should return negative error codes on failures.
However, in its implementation, it incorrectly returns 1. This patch fixes the
bug, returning proper error codes on failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
post input_sync only when there are input events posted
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure everything reported from pad are registered
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sometime valid events may not be supported by the driver yet. Make
sure we don't process them when the code is not ready.
This fix prevents a kernel panic due to unsupported HID events.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is unnecessary to return a value since nothing is expecting a
value from it.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We have the %pU printf extension for doing exactly this. Saves some
.text, and is likely also a little faster.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the gpio-as-irq support has been added, the driver now depends
on proper support being available in gpiolib.
Fixes: 13de9cca51 ("HID: cp2112: add IRQ chip handling")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update the hid-asus module to add multitouch support for the Asus i2c touchpad.
This patch aims to resolve the issue raised here:
https://bugzilla.kernel.org/show_bug.cgi?id=120181
The issue is in relation to an Asus touchpad device which currently does not
have multitouch support.
The device currently falls through to the hid-generic driver which
treats the device as a mouse.
This patch aims to add the multitouch support.
[jkosina@suse.cz: move most of the 'patch comment' into actual changelog]
[jkosina@suse.cz: drop hunk that changes ->name of the driver]
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: Victor Vlasenko <victor.vlasenko@sysgears.com>
Signed-off-by: Frederik Wenigwieser <frederik.wenigwieser@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Although unlikely but it is possible that when a connect or disconnect
request is issued to the firmware, before the response comes, user
terminates the client session. In this case when the response is arrived
there is no matching client instance in the list of currently active
clients. In this case, don't issue call to wake up a waiting client.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for USB based DS4 dongle device, which allows connecting
a DS4 through Bluetooth, but hides Bluetooth from the host system.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS4 side of hid-sony used the hid-core layer to assign buttons
and axes based on the HID report descriptors. The default mapping
was strange e.g. right stick using ABS_Z/ABS_RZ or the physical
'south button' being reported as BTN_EAST etcetera.
This patch makes the DS4 side ofi the hid-sony driver comply to
the Linux game controller spec as suggested in a discussion with
Dmitry on the linux-input list.
Currently the main user of the DS4 is the SDL2 library, which has
a mapping table using vendor/device/version as a key. In order to
not break SDL2 we discussed adjusting the version number, so it
can have both mappings. This was discust on linux-input and we
discussed privately with SDL2 developers.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The dualshock 4 supports both analog sticks of which one uses
ABS_X/_Y and a touchpad. In a recent discussion with Dmitry about
some input-mt changes we proposed for disabling pointer emulation from
input_mt_sync_frame, Dmitry mentioned ABS_X/_Y should report the
same data as ABS_MT_POSITION_X/_Y. The current driver is mixing axes
for different subdevices. It was suggested to make the touchpad
its own sub-device.
This patch turns the touchpad into its own device. In addition
this patch also moves the button underneath the touchpad into
the new device. It felt like this button should be part of the
device. No known user space application (not even SDL2) seems to
be using it.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A previous patch moved most input initialization from sony_probe to
sony_input_configured to avoid some race conditions. The driver has some
special logic to prevent the device to get registered twice in case the
user connects it both over Bluetooth and USB. When this condition
happens sony_input_configured returns a failure, but sony_probe continues
as hid_hw_start doesn't fail. As was discussed on linux-input, it is
acceptable for this function to fail.
This patch adds a check for the HID_CLAIMED_INPUT flag within sony_probe
to determine whether initialization succeeded correctly. The flag is
not set by the HID layer when sony_input_configured fails.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The GPIO part doesn't provide interrupts when GPIO are toggled.
So use a polling mechanism if someone requests a GPIO as an IRQ.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of forcing the level trigger of the IRQ, we can count
on ACPI or OF to set it up for us.
The first release of the HID over I2C specification mentioned
that the level trigger needed to be active low. In the latest
version of the specification, there is no such explicit mention,
so it's better to not assume one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We already have in place a quirk for Windows 8 devices, but it looks
like the Surface Cover are not conforming to it.
Given that we are only interested in 3 feature reports (the ones that
the Windows driver retrieves), we should be safe to unconditionally apply
the quirk to everybody.
In case there is an issue with a controller, we can always mark it as such
in the transport driver, and hid-multitouch won't try to retrieve the
feature report.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no reasons to filter out keyboard and consumer control collections
in hid-multitouch.
With the previous hid-input fix, there is now a full support of the Type
Cover and we can remove all specific bits from hid-core and hid-microsoft.
hid-multitouch will automatically set HID_QUIRK_NO_INIT_REPORTS so we can
also remove it from the list of ushbid quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The purpose of HID_QUIRK_MULTI_INPUT is to have an input device per
report id. This is useful when the HID device presents several HID
collections of different device types.
The current implementation of hid-input creates one input node per id per
type (input or output). This is problematic for the LEDs of a keyboard as
they are often set through an output report. The current code creates
one input node with all the keyboard keys, and one other with only the
LEDs.
To solve this, we use a two-passes way:
- first, we initialize all input nodes and associate one per report id
- then, we register all the input nodes
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to https://msdn.microsoft.com/en-us/library/windows/hardware/mt604195(v=vs.85).aspx
external buttons have some weird usage mapping:
- Button 2 Indicates Button State for external button for primary
(default left) clicking.
- Button 3 Indicates Button State for external button for secondary
(default right) clicking.
So in the current state, the buttons are mapped to right and middle.
Move the usage by one to correctly map the external buttons.
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One more device requiring a quirk :/
Reported-by: Christian-Nils Boda <christian-nils.boda@gadz.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One more device requiring a quirk :/
[jkosina@suse.cz: update comment based on Bastien's remark]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When user tried to read some fields like hysteresis from IIO sysfs on some
systems, it fails. The reason is that this field is a byte field and caller
of sensor_hub_get_feature() passes a buffer of 4 bytes. Here the function
sensor_hub_get_feature() copies the single byte from the report to the
caller buffer and returns "1" as the number of bytes copied. So caller
can use the return value.
But this is done by multiple callers, so if we just change the
sensor_hub_get_feature so that caller buffer is initialized with 0s
then we don't to change all functions.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for not JP versions of the Microsoft Surface 4 Type Cover Pro
[jkosina@suse.cz: The identical patch has been sent by Jeff Farthing, so I am
including his signoff as well]
Signed-off-by: Jeff Farthing <jeff@jfarthing.com>
Signed-off-by: Daniel Keller <daniel.keller@gcd.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
[jkosina@suse.cz: fix up second usage of hid_hw_raw_request(), spotted by
0day build bot]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Use a spinlock to prevent concurrent accesses to the buffer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
set_current_task() must be called before schedule_timeout(), for this
driver, in order to avoid incorrect usage, use msleep_interrupt()
instead.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The macro timed_wait_for_timeout() only be used in one function, so move
this marco from header file and change it to a function in ipc.c, where
it is used.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The macro timed_wait_for() in utils.h isn't used in current ipc
driver, so remove it for avoiding confusion.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for the THQ uDraw tablet for the PS3, as
4 separate device nodes, so that user-space can easily consume
events coming from the hardware.
Note that the touchpad two-finger support is fairly unreliable,
and a right-click can only be achieved with a two-finger tap
with the two fingers slightly apart (about 1cm should be enough).
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The eraser end of the 8K pen available for the MobileStudio Pro has a tool
ID of 0x84a. The 'wacom_intuos_get_tool_type' function does not currently
recognize this ID, causing it to return BTN_TOOL_PEN rather than
BTN_TOOL_RUBBER. This does not cause a problem for the MobileStudio Pro
since, as a HID_GENERIC device, the driver relies on the state of the
HID_DG_INVERT usage instead. It would, however, cause problems if the pen
is used with devices that use the traditional 'wacom_intuos_irq' codepath
instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is trying to clear the lower 32 bits but the type is wrong so it
clears everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Certain devices produced by Weida Tech need to have a wakeup command sent to
them before powering on. The call itself will come back with error, but the
device can be powered on afterwards.
[jkosina@suse.cz: rewrite changelog]
[jkosina@suse.cz: remove unused device ID addition]
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ts_format.reserved is not used anywhere yet, but the compiler generates a
warning when the struct's (uninitialized) field is being copied around
drivers/hid/intel-ish-hid/ipc/ipc.c: In function ‘write_ipc_from_queue’:
drivers/hid/intel-ish-hid/ipc/ipc.c:316: warning: ‘ts_format.reserved’ may be used uninitialized in this function
Avoid this by force-initializing the field to zero.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.
But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.
This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new module named hid-mf that implements force feedback for game
controller adapters manufactured by Mayflash. Currently only the PS3 adapter is
supported, other adapters still need to be tested.
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All known gamepad adapters by Mayflash (identified as Dragonrise) need
HID_QUIRK_MULTI_INPUT to split them up into four input devices. Without this
quirk those adapters are falsely recognized as tablets. Fixes bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like many similar devices it needs a quirk to work.
Issuing the request gets the device into an irrecoverable state.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix
drivers/hid/intel-ish-hid/ipc/pci-ish.c:247:12: warning: ‘ish_suspend’ defined but not used [-Wunused-function]
static int ish_suspend(struct device *device)
^
drivers/hid/intel-ish-hid/ipc/pci-ish.c:282:12: warning: ‘ish_resume’ defined but not used [-Wunused-function]
static int ish_resume(struct device *device)
^
by sticking them in the CONFIG_PM range too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-input@vger.kernel.org
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When report count is more than one and report size is not 4 bytes, then we
need some packing into result buffer from the caller of function
sensor_hub_get_feature.
By default the value extracted from a field is 4 bytes from hid core
(using hid_hw_request(hsdev->hdev, report, HID_REQ_GET_REPORT)), even
if report size if less than 4 byte. So when we copy data to user buffer in
sensor_hub_get_feature, we need to only copy report size bytes even
when report count is more than 1. This is
not an issue for most of the sensor hub fields as report count will be 1
where we already copy only report size bytes, but some string fields
like description, it is a problem as the report count will be more than 1.
For example:
Field(6)
Physical(Sensor.OtherCustom)
Application(Sensor.Sensor)
Usage(11)
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Report Size(16)
Report Count(11)
Here since the report size is 2 bytes, we will have 2 additional bytes of
0s copied into user buffer, if we directly copy to user buffer from
report->field[]->value
This change will copy report size bytes into the buffer of caller for each
usage report->field[]->value. So for example without this change, the
data displayed for a custom sensor field "sensor-model":
76 00 101 00 110 00 111 00 118 00 111
(truncated to report count of 11)
With change
76 101 110 111 118 111 32 89 111 103 97
("Lenovo Yoga" in ASCII )
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The "Steering" usage (HID_UP_SIMULATION | 0xc8) is defined in HUT 1.12 as
follows:
"A steering wheel is a single degree-of-freedom device that rotates about
an axis. The zero position is always the neutral or 'straight ahead'
position, with positive values turning clockwise and negative values
turning counterclockwise. If the Coordinate Values Wrap attribute is
set, the steering wheel can be turned past 360 degrees."
The hidinput_configure_usage function canonically maps this usage to the
ABS_WHEEL axis, but hidinput_calc_abs_res does not recognize this axis
as one for which it can calculate a resolution. This effectively prevents
wheels from being assigned a proper resolution that userspace can use
to determine the precise angle of input.
This commit adds ABS_WHEEL as a rotational axis to hidinput_calc_abs_res.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID specification that the MobileStudio Pro follows includes usages
for several values that would be good to support so that future devices
"just work" out of the box. Extend the HID_GENERIC pad codepath to handle
these usages.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for usages that may appear on the pen or pad interface which
report the state of the tablet battery.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As with usages for the pen, the Custom HID specificiation includes
usages for the pad. Here we add functions to map and handle most
of the pad usages present on the MobileStudio Pro.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To accommodate
such sensors in the HID_GENERIC codepath, we add support for the
necessary vendor-defined HID feature usages and adjust the min/max
values of the X and Y axes accordingly, similar to what is done in
the non-generic codepath.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To ensure that
pen coordinates are mapped to the correct on-screen location, the driver
sets the minimum and maximum axis values of X and Y to those coordinates
which coincide with the screen edge. These values are simply the
hardware minimum/maximum plus/minus the outbound size for a particular
edge.
When outbound support was added/updated in ac414da, fa77034, and
ecd618d, we decided to have the wacom_features structs store the desired
minimum and maximum values directly. In hindsight, this was perhaps not
the best choice since it has allowed minor errors to crop up unnoticed.
Some tablets have had their coordinates over-corrected (e.g. most of the
devices "fixed" in ecd618d were already adjusted in ac414da), while
others never had a correction applied (e.g. the ISDv5 325, whose
declared maximum the hardware maximum instead of the outbound maximum).
A less error-prone method of handling the outbound is to let the driver
calculate the correct minimum/maximum values by providing it with both
the actual hardware maximums and the size of the outbound on each edge.
These values are more easy to verify as correct since the values can be
trivially compared against specifications.
This patch reverts the declared maximum values to the actual hardware
maximums, e.g. as declared prior to ac414da (values for these and other
display tablets that were subsuquently introduced have been verified
against specs). Per-edge outbound sizes are stored in the wacom_features
struct as offset_{left,right,top,bottom} and used in combination with
the hardware ranges to calculate effective axis ranges for ABS_X and
ABS_Y.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices following the new Custom HID mode specification (as well as even
some recent component sensors which use the same standard HID usage)
are capable of reporting tool ID information that we need to relay to
userspace. This patch adds support for reading and relaying the tool
type information, which is (unfortunately) split across two usages.
We also advertise the existence of tool types beyond BTN_TOOL_PEN
that might be available.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_intuos_inout' function incorrectly assmebles tool IDs from the
proximity report, shifting the higher values of the ID four bits farther
than intended. This problem was not detected until too late, but has not
caused any issues since the incorrect IDs still fit in a 32-bit integer
and userspace programs have not required the value to match the hardware
(just that the values are unique and constant).
The tool IDs reported by the new MobileStudio Pro (or any future
HID_GENERIC device that supports them) do not suffer from the same
assembly issue, however. In order for 'wacom_intuos_get_tool_type' to
work for with both codepaths, we correct this issue internally and
have 'wacom_intuos_general' only mangle the ID when it is posted to
userspace.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom's professional tablets beginning with the Intuos4 are capable of
reporting an intermediate degree of proximity where the pen is no longer
close enough to communicate with ("in prox"), but still close enough to
be sensed ("in range"). This additional state is particularly useful for
performing palm rejection as it allows the driver to disable the touch
sensor while the pen is a greater distance from the tablet.
Like other professional tablets, the new MobileStudio Pro also reports
this intermeidate "in range" proximity state. Its descriptor assigns
usage 0xff0d0036 to this bit. Normally 'wacom_equivalent_usage' would
translate this to the standard HID "Quality" usage, but since this has
a different meaning we have it explicitly ignore the usage and define
it ourselves as "Sense" (since "In Range" is already defined by the
HID standard and interpreted by our driver as meaning "in prox").
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The airbrush fingerwheel does not have a usage that corresponds cleanly
with a standard HID usage, so we add explicit support for it via its
vendor-defined usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The vendor-defined 0xFF0D01032 ("Distance") usage is nearly equivalent to
HID_GD_Z, except that the axis direction is inverted. Unlike HID_GD_Z which
increases in value as the pen-to-surface distance is decreased, this usage
decreases. Treat this usage as a special case to ensure we don't invert the
scale to be ABS_DISTANCE compatible like we do for HID_GD_Z.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom's new "MobileStudio Pro" tablets are the first devices in their
branded product line-up to include a usable HID descriptor for the pen
interface. Like prior branded products, the device can operate in one
of two modes: 'Standard HID', and 'Wacom Custom HID'. Although the
first mode is usable by the HID_GENERIC codepath as-is (huzzah!), it is
subject to some restrictions -- most notably pressure being limited
to 2048 levels instead of 8192. To ensure tablets that include support
for Custom HID mode work optimally, we add support for its usages and
switch the device to Custom HID mode if possible.
The usages defined for Custom HID mode are often numerically similar to
their standard HID equivalents, allowing us to write a simple translation
function that takes arbitrary HID usages as input and which returns
the corresponding standard HID usage as output (if one exists). Switching
on this translated usage instead of the actual usage allows the existing
cases to apply to both modes of operation without having to explicitly
define every Custom HID usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID standard defines usages that allow digitizers to report the pen's
height, tilt, and rotation and which are used by Wacom's new "MobileStudio
Pro" devices.
Note that 'hidinput_calc_abs_res' expects ABS_Z (historically used by our
driver to report twist) to have linear units. To ensure it calculates a
resolution with the actually-angular units provided in the HID descriptor
we nedd to lie and tell it we're calculating it for the (rotational) ABS_RZ
axis instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The product name received from the string descriptor in the new MobileStudio
Pro line of tablets begins with "Wacom", which leads to unnecessary visual
noise in the device name when appended to the vendor name which also includes
"Wacom". Look for and fix cases like this.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISDv4 devices have long supported reporting data from each of two barrel
switches, but HID_DG_BARRELSWITCH2 itself was only recently standardized.
Prior to its adoption, ISDv4 devices would associate the bit indicating
the state of the second barrel switch with the "Undefined" 0x000D0000
usage. Although most such devices have explicit support, a few use the
HID_GENERIC codepath which ignores the "Undefined" usage.
This patch adds code which detects the presence of a pre-standard second
barrel switch and corrects the usage value so that the HID_GENERIC code
will declare its presence and report its state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This just centralizes the logic used in both wacom_setup_numbered_buttons
and wacom_report_numbered_buttons so that they don't drift out of sync.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We've defined several new usages (e.g. WACOM_G9_PEN and WACOM_G9_TOUCHSCREEN)
which aren't checked by the WACOM_PEN_FIELD and WACOM_FINGER_FIELD macros but
probably should be.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Our loose use of "pen" and "digitizer" in the naming of several of our
vendor-defined usages may be a source of confusion given that the terms
have specific meaning within the HID specification. "Pen" specifically
refers to "an integrated display that allows the use of a stylus" (e.g.
something like a tablet PC or Cintiq) wheras "Digitizer" is a better
fit for opaque tablets like an Intuos.
While we're at it, go ahead and rename the definitions to make them more
distinct and better match up with the convention used by HID (e.g. the use
of '_UP_' for usage pages) and make them more distinct.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When i2c-core doesn't find the IRQ associated to the GPIO because
the gpiochip is not available, it assigns -EPROBE_DEFER to the irq.
We need to bail out there and on any other error in an IRQ.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit a485923efb ("HID: i2c-hid: Add support for ACPI
GPIO interrupts") and commit a7d2bf25a4 ("HID: i2c-hid: Do not fail
probing if gpiolib is not enabled") at the same time.
Since commit c884fbd452 ("gpio / ACPI: Add support for retrieving
GpioInt resources from a device") i2c_core already set the IRQ by
looking into the ACPI tree and retrieving the gpioInt. So we just
have some boiler-plate here that is not needed anymore.
The only downside effect here is that now we are not exiting early
enough if the irq is set to -EPROBE_DEFER or any other error, but
this is going to be fixed in the following patch.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Akai MIDImix (09e8:0031) is a MIDI fader controller that speaks
regular MIDI and works well with Linux. However, initialization gets
delayed due to reports timeout:
[3643645.631124] hid-generic 0003:09E8:0031.0020: timeout initializing reports
[3643645.632416] hid-generic 0003:09E8:0031.0020: hiddev0: USB HID v1.11 Device [AKAI MIDI Mix] on usb-0000:00:14.0-2/input0
Adding "usbhid.quirks=0x09e8:0x0031:0x20000000" on the kernel
command line makes the issues go away.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 18339f59c3 ("HID: dragonrise: fix HID...") because it
breaks certain dragonrise 0079:0006 gamepads. While it may fix a breakage
caused by commit 79346d620e ("HID: input: force generic axis to be mapped
to their user space axis"), it is probable that the manufacturer released
different hardware with the same PID so this fix works for only a subset
and breaks the other gamepads sharing the PID.
What is needed is another more generic solution which fixes 79346d620e
("HID: input: force generic axis ...") breakage for this controller: we
need to add an exception for this driver to make it keep the old behaviour
previous to the initial breakage (this is done in patch 2 of this series).
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 79346d620e ("HID: input: force generic axis to be mapped to their
user space axis") made mapping generic axes to their userspace equivalents
mandatory and some lower end gamepads which were depending on the previous
behaviour suffered severe regressions because they were reusing axes and
expecting hid-input to multiplex their map to the respective userspace axis
by always searching for and using the next available axis.
One solution is to add a hid quirk for this type of "previous" behaviour in
hid-input to bypass the new axes policy in favour of the old one, but since
only one hardware vendor seems to be affected negatively we're better off
making and exception and mapping in the driver for now; if more vendors or
drivers turn out to experience the problem we should reconsider the quirk
solution.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The motion sensor values are 16-bit, so make the value range match.
It is hard to reach the upper values, but they can be reached. At
least the current accelerometer value of 8192 is very easy to pass.
It is still not nice that the motion sensors live in no man's land
in between ABS_MISC and ABS_MT_SLOT, but that's something for another
time, which the proposed ABS_ACCEL_*/ABS_GYRO_* were meant for.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Read the touch history field in the HID descriptor and use this value
to determine how many touch events to read from the report. As part
of this patch, we did a first attempt of making the offset calculation
code less magical.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a CRC value to each output report. This removes the need for the
'no output reports on interrupt end-point' quirk.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Put the report type (feature / output) in the report size definitions.
This prevents name collisions later on for other different reports, which use
the same report id, but have a different size.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Early on the sony_probe function calls hid_hw_start to start the hardware.
Afterwards it issues some hardware requests, initializes other functionality
like Force Feedback, power classes and others. However by the time
hid_hw_start returns, the device nodes have already been created, which leads
to a race condition by user space applications which may detect the device
prior to completion of initialization. We have observed this problem many
times, this patch fixes the problem.
This patch moves most of sony_probe to sony_input_configured, which is called
prior to device registration. This fixes the race condition and the same
approach is used in other HID drivers.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- Integrated Sensor Hub support (Cherrytrail+) from Srinivas Pandruvada
- Big cleanup of Wacom driver; namely it's now using devres, and the
standardized LED API so that libinput doesn't need to have root
access any more, with substantial amount of other cleanups
piggy-backing on top. All this from Benjamin Tissoires
- Report descriptor parsing would now ignore and out-of-range System
controls in case of the application actually being System Control.
This fixes quite some issues with several devices, and allows us to
remove a few ->report_fixup callbacks. From Benjamin Tissoires
- ... a lot of other assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (76 commits)
HID: add missing \n to end of dev_warn messages
HID: alps: fix multitouch cursor issue
HID: hid-logitech: Documentation updates/corrections
HID: hid-logitech: Improve Wingman Formula Force GP support
HID: hid-logitech: Rewrite of descriptor for all DF wheels
HID: hid-logitech: Compute combined pedals value
HID: hid-logitech: Add combined pedal support Logitech wheels
HID: hid-logitech: Introduce control for combined pedals feature
HID: sony: Update copyright and add Dualshock 4 rate control note
HID: sony: Defer the initial USB Sixaxis output report
HID: sony: Relax duplicate checking for USB-only devices
Revert "HID: microsoft: fix invalid rdesc for 3k kbd"
HID: alps: fix error return code in alps_input_configured()
HID: alps: fix stick device not working after resume
HID: support for keyboard - Corsair STRAFE
HID: alps: Fix memory leak
HID: uclogic: Add support for UC-Logic TWHA60 v3
HID: uclogic: Override constant descriptors
HID: uclogic: Support UGTizer GP0610 partially
HID: uclogic: Add support for several more tablets
...
Issue reproduction procedure:
1. three or more fingers put on Touchpad.
2. release fingers from Touchpad.
3. move the cursor by one finger.
4. the cursor does not move.
Cause:
We do not notify multi fingers state correctly to input subsystem. For
example, when three fingers release from Touchpad, fingers state is 3 -> 0. It
needs to notify first, second and third finger's releasing state.
Fix this by not breaking out on z axis and move x,y,z input handling
code to the correct place so that it's in fact per-finger.
[jkosina@suse.cz: reword changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ForceFeedback support for the Formula Force GP into hid-lgff4
and re-write HID descriptor, thus allowing combined pedals or not
as user desires.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rewrite the HID descriptor for _all_ Driving Force wheels (real
or emulated) so that they can report separate Accelerator and
Brake axis.
If the user wants a combined accel/brake axis, they can use the
'combined pedals' feature.
$ echo 1 > /sys/bus/hid/devices/<device-id>/combine_pedals
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for computing a combined accelerator/brake axis for wheels
which don't contain combined data in their HID stream.
This includes DFGT, G25, G27, G29 and Wii-Wheel.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for reporting a combined accelerator/brake axis for wheels
which contain combined data in their HID stream.
This includes DF, MOMO, MOMO2 and DFP.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce a dev_attr which can be used to combine the accelerator
and brake pedals into a single axis. This is useful for older games
which can not handle seperate accelerator and brake.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update the copyright notice with the current year and add a note
about values for controlling the Dualshock 4 reporting rate.
Processing reports at the default full rate of 1000hz can be too
demanding for some low-power embedded processors so noting
alternate values for people working with this hardware can be useful.
Thanks to Rostislav Pehlivanov for finding these values.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When initially connected via USB the Sixaxis isn't fully initialized
until the PS logo button is pressed and won't send any input reports
nor will any state set by output reports be retained.
This adds a 'defer_initialization' flag to the sony_sc struct which,
when set, will delay sending any output reports until the first input
report has arrived. This flag is used with the USB Sixaxis to ensure
that any state sent will persist since, until the PS button is pushed,
any changes sent to the controller via an output report will be lost
after a couple of seconds.
The initial state of the controller is still configured at the time
of the initial connection and won't be internally modified after that,
so any state set by the user between that time and the recepit of the
first input report won't be lost.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some USB-only devices which masquerade as Sixaxis controllers report the
same generic Bluetooth address for all hardware when queried via the HID
report. This causes these devices to be wrongly rejected as duplicates
when more than one is connected at once.
This introduces a connection type comparison when checking for duplicates
and only rejects the newly connected device if the existing matching
device is connected using a different connection protocol.
The results of the connection type comparison are also used when
registering power supply info as the device Bluetooth address is used
as the unique identifier string. In cases where more than one valid
device has the same Bluetooth address the device ID is now appended
to the power supply name string to avoid name collisions when
registering the power supply information.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3ccc60f9d8.
While investigating bug https://bugzilla.kernel.org/show_bug.cgi?id=37982 ,
there was solid evidences that Microsoft reused the same report
descriptor for the its Digital Media keyboard series.
Since 1989dad "HID: input: ignore System Control application usages if not
System Controls", the keyboard series do not produce a spurious joystick
input device inode without needing to patch the problematic report
descriptor. As such the MS_RDESC_3K reportdescriptor fixup can be removed.
Signed-off-by: Michel Hermier <michel.hermier@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
While at it, remove redundant input_free_device(NULL) call.
[jkosina@suse.cz: ammend changelog]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stick device does not work after resume, add U1_SP_ABS_MODE flag can
make the device work after resume.
This has been discovered by pure guesswork, based on how the existing code uses
U1_TP_ABS_MODE flag on both initialization and resume.
I also tested the the patch on an ALPS touchpad without stick device, did not
notice any side effect on suspend/resume, so I made the U1_SP_ABS_MODE flag
mandatory.
[jkosina@suse.cz: made changelog more verbose]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add quirk for Corsair STRAFE keyboard, similarly to what we've been
doing for other CORSAIR devices already, in order to avoid long delays
during boot.
[jkosina@suse.cz: reword changelog a little bit]
Signed-off-by: Marian Krivos <marian.krivos@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A kfree(readbuf) call was missed if hid_hw_raw_request() fails, fix it.
Also avoid mixing direct return with goto in the error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the third version of UC-Logic TWHA60, which has
three interfaces and responds to initialization.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make uclogic_report_fixup override constant descriptors with generated
descriptors, so models reusing product ID, but working with generated
descriptor get correct one.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add partial support for the UGTizer GP0610 tablet (aka iBall PF1064U,
aka UGTizer GT1060) to the hid-uclogic.c driver.
The pen input is supported fully, but frame buttons and wheel don't work
yet.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Enable abstract keyboard mode for Huion tablets, which makes them report
frame buttons using the pen interface and report ID. Divert these
reports to a virtual report ID describing them.
This makes the tablet compatible with xf86-input-wacom and libinput,
but stops the frame buttons from reporting keyboard events.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unnecessary allocation failure messages from hid-uclogic.c,
following the checkpatch.pl recommendations.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a dedicated, fixed report descriptor for the second version of KYE
MousePen i608X graphics tablet. The descriptor fixes pressure and
drawing area ranges.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename the device ID macro for the second version of KYE MousePen i608x
graphics tablet to have "V" in its name to signify that "2" is a
version.
I.e. USB_DEVICE_ID_KYE_MOUSEPEN_I608X_2 ->
USB_DEVICE_ID_KYE_MOUSEPEN_I608X_V2
This also makes applying additional fixes from DIGImend easier.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove comments with broken links to tablet descriptions from
hid-kye/uclogic/waltop drivers.
They pointed to now dead DIGImend project wiki at sf.net. Even though
the DIGImend project still hosts descriptions, now at
digimend.github.io, it's better to avoid them going stale again, and let
anyone interested search the web instead.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft is reusing its report descriptor again and again, and part of it
looks like this:
0x05, 0x01, // Usage Page (Generic Desktop) 299
0x09, 0x80, // Usage (System Control) 301
0xa1, 0x01, // Collection (Application) 303
0x85, 0x03, // Report ID (3) 305
0x19, 0x00, // Usage Minimum (0) 307
0x29, 0xff, // Usage Maximum (255) 309
0x15, 0x00, // Logical Minimum (0) 311
0x26, 0xff, 0x00, // Logical Maximum (255) 313
0x81, 0x00, // Input (Data,Arr,Abs) 316
0xc0, // End Collection 318
While there is nothing wrong in term of processing, we do however blindly
map the full usage range (it's an array) from 0x00 to 0xff, which creates
some interesting axis, like ABS_X|Y, and a bunch of ABS_MISC + n.
While libinput and other stacks don't care that much (we can detect them),
joydev is very happy and attaches itself to the mouse or keyboard.
The problem is that joydev now handles the device as a joystick, but given
that we have a HID array, it sets all the ABS_* values to 0. And in its
world, 0 means -32767 (minimum value), which sends spurious events to games
(think Steam).
It looks like hid-microsoft tries to tackle the very same problem with its
.report_fixup callback. But fixing the report descriptor is an endless task
and is quite obfuscated.
So take the hammer, and decide that if the application is meant to be
System Control, any other usage not in the System Control range should
be ignored.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1325354
Link: https://bugzilla.kernel.org/show_bug.cgi?id=28912
Link: https://github.com/ValveSoftware/steam-for-linux/issues/3384
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1325354
Link: https://bugzilla.kernel.org/show_bug.cgi?id=37982
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for the Microsoft Surface 4 Type Cover Pro (JP).
Signed-off-by: Yuta Kobayashi <alu.ula@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Need enum quirk to change the base of enums to 1 for
power and report descriptors.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver is responsible for implementing ISH HID client, which
gets HID description and report. Once it has completely gets
report descriptors, it registers as a HID LL drivers. This implements
necessary callbacks so that it can be used by HID sensor hub driver.
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This layer is responsible for
- Enumerating over PCI bus
- Inform FW about host readiness
- Provide HW interface to transport layer for control and messages
- Interrupt handling and routing
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ISH transport layer (ishtp) is a bi-directional protocol implemented
on the top of PCI based inter processor communication layer. This layer
offers:
- Connection management
- Flow control with the firmware
- Multiple client sessions
- Client message transfer
- Client message reception
- DMA for RX and TX for fast data transfer
Refer to Documentation/hid/intel-ish-hid.txt for
overview of the functionality implemented in this layer.
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a touchscreen contains both multitouch and single-touch reports in its
descriptor in that order, the driver may overwrite information it saved
about the format of the multitouch report. This can cause the report
processing code to get tripped up and send an incorrect event stream to
userspace.
In particular, this can cause last_slot_field to be overwritten with the
result that the driver prematurely assumes it has finished processing a
slot and sending the ABS_MT_SLOT event at the wrong point in time,
associating events for the current contact with the following contact
instead.
To prevent this from occurring, we update the value of last_slot_field
durring the pre_report phase to ensure that it is correct for the report
that is to be processed.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch arbitration is always on in wacom.ko. However, there are
touch enabled applications use both pen and touch simultaneously.
We should provide an option for userland to decide if they want
arbitration on or off.
This patch sets default touch_arbitration to on since most userland
apps are not ready to process pen and touch events simultaneously.
In the future, when userland is ready to accept pen and touch events
together, we will switch default touch_arbitration to off.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'oVid' and 'oPid' variables used by wacom_are_sibling are a hacky
solution to the problem of the driver historically having few good
heuristics to use in determining if two devices should be considered
siblings or not. While it works well enough for explicitly supported
devices, it offers no help for HID_GENERIC devices. Now that we have
a bit more information (e.g. direct/indirect) available to us though,
we should make use of it it to improve the pairing of such devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Direct" input devices like Cintiqs and Tablet PCs set the INPUT_PROP_DIRECT
property to notify userspace that the sensor and screen are overlaid. This
information can also be useful elsewhere within the kernel driver, however,
so we introduce a new WACOM_DEVICETYPE_DIRECT that signals this to other
kernel code.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of displaying a generic "tablet", now g-c-c shows a pretty
"Wacom Intuos Pro S (WL)".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like upowerd is ignoring this since October 2013, so there is
no need to keep this around in the kernel.
And as mentioned in 8aaa592 (linux: Ignore ACs coming from devices) in
the upower tree, "We already have enough information on the device
battery".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When upowerd detects a new device, it tries to map this new device to
an input to guess its kind. It works OK for wired tablets when the
wireless module and its battery are attached, but not so well when
connected over wireless.
In that case, the battery is attached to the wireless HID node, not
the Pen or Pad HID node. So there is no input node as a parent of the
reported battery, which means it will be showed as a computer battery
in gnome-control-center.
If we set the power supply type to USB, upowerd has a heuristic that
detects "wacom_" in the name of the power_supply, and set the type to
tablet. So it's now clear that the reported battery of from a tablet.
(see https://cgit.freedesktop.org/upower/tree/src/linux/up-device-supply.c)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 24HD has 1 button per LED (first three buttons of each group).
We need a special treatment for them as it's not a uniq button that
switches between the LEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code for 21UX2 and 24HD makes the LED group 1 on the left, and
the group 0 on the right. The buttons are ordered in the other way,
but libwacom already exports those that way. So we simply can't reassign
LED group 0 to the left buttons, and have to quirk the incoming data...
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EKR switches the LED directly, and there is no point in having
userspace handling the switch it self when it's easy enough to do
in the kernel.
The other benefit is that now userspace does not need to have root access
to the LED but need only to read them with user privileges.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a bug (?) in devm_led_classdev_register() in which its increments
the refcount of the parent. If the parent is an input device, that means
the ref count never reaches 0 when devm_input_device_release() gets called.
This means that the LEDs and all the devres resources attached to the
input device are not released.
Manually force the release of the group so that the leds are released once
we are done using them.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The now obsolete sysfs files for LEDs and EKRemote are kept for backward
compatibility.
Both the EKR (read-only) and the regular Cintiqs and Intuos are now
sharing the same led API.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or Gnome complains about an empty battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, all the remotes attached to the same receiver would share the
same power_supply. That's not good as the remotes will constantly change
the battery information according to their own state.
To have something generic enough, we introduce struct wacom_battery
which regroups all the information we need for a battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres, we can now afford to create more than one input node
without having to overload the remove/failure paths. Having one input
node per remote is something which should have been implemented from start
but the probability of having users with several remotes is quite low.
Anyway, still, better looking at the future and implement things properly.
Remote input nodes will be freed/unregistered magically as they are
created in the devres group &remote->remotes[index].
We need to open the hid node now that the remotes are dynamically
allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No functional changes, just a prep patch for the one after.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will be useful when each remote will be assigned its own input device.
We won't need to unregister each input and sysfs and other elements one
at a time.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_remote_create_attr_group() and wacom_remote_destroy_attr_group()
functions were both allocating/destroying the sysfs groups but also
initializing the parameters for the remotes. Have proper functions
that can be called and extended.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres management, we don't need to remember a lot of failure
path. One or two is enough.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we want to have one input device per remote, it's better to have our
own struct wacom_remote which is dynamically allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_remote_status_irq() sends information of addition/removal of EKR.
We want to allocate one input node per remote, so better having this
in a separate worker, not handled in the IRQ directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to add an action to ensure wacom->led.groups is null when
wacom_led_control() gets called after the resources has been freed.
This also prevents to send a LED command when there is no support
from the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_release_shared_data() and wacom_remove_shared_data() are moved up
so they can be referenced in wacom_add_shared_data().
There is no point in explicitly setting wacom_wac1->shared->type to 0 in
wacom_wireless_work() (plus this would give an oops).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We started switching the driver to devres, so we should use it as much
as possible.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The sysfs group was indeed removed by kobject_put(wacom->remote_dir) in
wacom_remove(), but the name of the group was never freed.
Also remove the misplaced kobject_put(wacom->remote_dir) in the error
path of wacom_remote_create_attr_group().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use our own wacom_devm_sysfs_create_group() as there is currently no
generic one. It has been requested at least twice [1][2] but has been
always rejected.
However, in the Wacom case, for the wirelessly connected devices, we need
to be able to release the created sysfs files without removing the parent
kobject.
[1] https://patchwork.kernel.org/patch/7526551/
[2] https://lkml.org/lkml/2013/3/14/728
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We currently have a complex clean_inputs() function while this can be
handled all by devres. Set a group that we can destroy in wireless_work().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_clean_inputs() around for now as the wireless
module is using it to dynamically remove the inputs on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_destroy_battery() around for now as the wireless
module and the remotes are using it to dynamically remove the battery
supply on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like the battery hijacked the wireless worker. That's not fair so
use a work queue per task.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like remotes, LEDs should be handled by themself, not magically behind
the inputs as they have a complete different life.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom->remote_dir has nothing to do with inputs, so better not magically
removing it when cleaning inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The type is never set but we check for it in wacom_wireless_irq().
It looks like this is a big hack from the beginning, so fill in the gap
only.
Untested.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since fd5f92b ("HID: wacom: reuse wacom_parse_and_register() in
wireless_work"), wacom->shared->type is not set.
Send the information of the battery if we have one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new device has 06a3:0cfa as identifiers, and the same quirks as the
other RAT models. It needs this fix in order not to confuse the xorg server
with its tristate button, which is reported as three different buttons, one
of which is always on.
[jkosina@suse.cz: drop unrelated whitespace hunk]
Signed-off-by: Mayeul Cantan <mayeul.cantan@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FutureMax Dance Mat claims to be a SixAxis controller
but breaks if descriptor fixups are applied. Detect the
device using its USB product string and disable fixups
when it is detected.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent commit added barry support to this driver, but that causes
a link failure when CONFIG_POWER_SUPPLY is not set:
drivers/hid/built-in.o: In function `hidpp_battery_get_property':
:(.text+0x1a834): undefined reference to `power_supply_get_drvdata'
drivers/hid/built-in.o: In function `hidpp_raw_event':
:(.text+0x1b10c): undefined reference to `power_supply_changed'
drivers/hid/built-in.o: In function `hidpp_connect_event':
:(.text+0x1bd88): undefined reference to `devm_power_supply_register'
:(.text+0x1be30): undefined reference to `power_supply_powers'
This adds a dependency, identically to the other HID drivers that need this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Fixes: 5a2b190cdd ("HID: logitech-hidpp: add battery support for HID++ 2.0 devices")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB device
Vendor 05ac (Apple)
Device 0267 (Magic Keyboard)
This keyboard supports both Bluetooth and USB connections, this patch
only covers USB.
Thanks to Maxime Poulin <maxpoulin64@gmail.com>
Signed-off-by: Jean-Gabriel Gill-Couture <jeangab@jeangab.fr.nf>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Properly handle this __le16 value on big endian systems.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that we can create battery power_supply sources, it's better to enable
the connect_event callback unconditionally.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If the 0x1000 Unified Battery Level Status feature exists, expose the battery
level.
The main drawback is that while a device is plugged in its battery level is 0.
To avoid exposing that as 0% charge we make up a number based on the charging
status.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Greynut Luxafor. This device has two groups of three
independent LED's each.
Successfully tested with such a device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the HID-compliant Delcom Visual Signal Indicator
generation 2 devices.
Successfully tested with part no 904000 from the family of these devices.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Delcom uses the report id to submit command information. To be able to
use the hidled framework also for Delcom devices we have to remove the
report id from struct hidled_config.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch validates the num_values parameter from userland during the
HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set
to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter
leading to a heap overflow.
Cc: stable@vger.kernel.org
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove an unnecessary codes.
Change input_ivent() function to appropriate function.
Add the device ID of "HID_DEVICE_ID_ALPS_U1_DUAL".
[jkosina@suse.cz: removed unnecessary bitshifts of values passed
input_report_key() as spotted by Dmitry]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that support for ThingM blink(1) was merged into the hid-led driver
the dedicated driver for this device can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for ThingM blink(1) and make the dedicated ThingM driver
obsolete.
Successfully tested with a blink(1) mk2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add i2c_hid_shutdown for i2c-hid driver to send suspend cmd & free
irq before device shutdown.
Some HW design (i.e. Umaro, a chromebook model) is that the power to
i2c hid device won't down after device shutdown. Also the i2c-hid driver
do not send suspend cmd to the hid i2c device and free its irq before
shutdown.So if We touch the touchscreen or some other i2c hid device,
the power consumtion will be go up even when the device is in shutdown
state.
Though the root cause maybe a HW issue. But it seems that it is a
good pratice to set power sleep for i2c-hid device before shutdown.
Signed-off-by: Guohua Zhong <ghzhong@yifangdigital.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All devices with ALPS_JP VID are handled by hid-alps driver, hence they require
an entry in hid_have_special_driver[].
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel printf format %*ph allows to print small buffers up to 64 bytes.
Make use of it to simplify the debug output code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Calculating size of the report as sizeof(pointer) always passess the length
corresponding to the pointer type, not the underlying data report.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver port was done carefully not to depend on USB at all, in favor of
being generic HID driver instead. Therefore there is no need to explicitly
talk about USB only in the config.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch migrates the USB LED driver to the HID subsystem.
Supported are Dream Cheeky Webmail Notifier / Friends Alert
and Riso Kagaku Webmail Notifier.
Benefits:
- Avoid using USB low-level calls and use the HID subsystem instead
(as this device provides a USB HID interface)
- Use standard LED subsystem instead of proprietary sysfs entries,
this allows e.g. to use the device with features like triggers
Successfully tested with a Dream Cheeky Webmail Notifier and a
Riso Kagaku Webmail Notifier compatible device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
i2c-hid devices' suspend/resume are usually time-consuming process.
For example, the touch controller(i2c-ATML1000:00) on ASUS T100 tablet
takes about 160ms for suspending and 120ms for resuming. This patch
enables i2c-hid devices to suspend/resume asynchronously. This will
take advantage of multicore and speed up system suspend/resume process.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many devices use userspace bluetooth stacks like BlueZ or Bluedroid in combination
with uhid. If any of these stacks is used with a HID device for which the driver
performs a HID request as part .probe (or technically another HID operation),
this results in a deadlock situation. The deadlock results in a 5 second timeout
for I/O operations in HID drivers, so isn't fatal, but none of the I/O operations
have a chance of succeeding.
The root cause for the problem is that uhid only allows for one request to be
processed at a time per uhid instance and locks out other operations. This means
that if a user space is creating a new HID device through 'UHID_CREATE', which
ultimately triggers '.probe' through the HID layer. Then any HID request e.g. a
read for calibration data would trigger a HID operation on uhid again, but it
won't go out to userspace, because it is still stuck in UHID_CREATE.
In addition bluetooth stacks are typically single threaded, so they wouldn't be
able to handle any requests while waiting on uhid.
Lucikly the UHID spec is somewhat flexible and allows for fixing the issue,
without breaking user space. The idea which the patch implements as discussed
with David Herrmann is to decouple adding of a hid device (which triggers .probe)
from UHID_CREATE. The work will kick off roughly once UHID_CREATE completed (or
else will wait a tiny bit of time in .probe for a lock). A HID driver has to call
HID to call 'hid_hw_start()' as part of .probe once it is ready for I/O, which
triggers UHID_START to user space. Any HID operations should function now within
.probe and won't deadlock because userspace is stuck on UHID_CREATE.
We verified this patch on Bluedroid with Android 6.0 and on desktop Linux with
BlueZ stacks. Prior to the patch they had the deadlock issue.
[jkosina@suse.cz: reword subject]
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The firmware found in the touch screen of an SP3 is buggy and may miss
to send lift off reports for contacts. Try to work around that issue by
using MT_QUIRK_NOT_SEEN_MEANS_UP.
based on a patch from: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
CC: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 7e12978 ("HID: wacom: break out wacom_intuos_get_tool_type") by accident
removed stylus_in_proximity flag for Intuos series while shuffling the code
around.
Fix that by reintroducing that flag setting in wacom_intuos_inout(), where
it originally was.
Fixes: 7e12978 ("HID: wacom: break out wacom_intuos_get_tool_type")
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fuzz present on the distance and tilt axes is noticable when a puck is
present, and userspace (specifically libinput) would like the ability to
filter out the noise. To facilitate this, we assign a fuzz value of '1'
for the distance and tilt axes. This is large enough to cover most of the
natural variation in distance value as the puck is moved around, and
enough to cover the jitter in rotation (reported through tilt axes) when
the puck is left alone.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices feature multiple interfaces/endpoints: a legacy BIOS/boot
interface (endpoint 0x81), as well as 2 corsair-specific keyboard interfaces
(endpoint 0x82, 0x83 IN/0x03 OUT) and an RGB LED control interface (endpoint
0x84 IN/0x04 OUT)
Because the extra 3 interfaces are not of subclass USB_INTERFACE_SUBCLASS_BOOT,
HID_QUIRK_NOGET is not automatically set on them and a 10s timeout per-endpoint
(30s per device) occurs initialising reports on boot. We configure
HID_QUIRK_NO_INIT_REPORTS for these devices.
Additionally the left-side G1-G18 macro keys on the K95RGB generate output on
the un-opened 0x82/0x83 endpoints which causes the keyboard to stop responding
waiting for this event to be collected. We enable HID_QUIRK_ALWAYS_POLL to
prevent this situation from occurring.
Signed-off-by: Trent Lloyd <trent@lloyd.id.au>
Tested-by: SUGNIAUX Wilfried <wsu@ppharm2k20.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Needed for v2 of the device firmware, otherwise kernel will stuck for few
seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot.
Signed-off-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LED core takes care of handling failed calls to thingm_let_set.
- print error message in set_brightness_delayed or
- pass error to caller in led_set_brightness_sync
Also the error message here doesn't provide any hint what actually
went wrong. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@rehat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use recently introduced flag LED_HW_PLUGGABLE to avoid warnings when
the device is unplugged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for how scaling linearization is computed in wiimote driver, by
Cyan Ogilvie
- endless retry loop fix in generic USB HID core reset-resume handling,
by Alan Stern
- two functional fixes affecting particular devices, and oops fix for
wacom driver, by Jason Gerecke
- multitouch slot numbering fix from Gabriele Mazzotta
- a couple more small fixes on top
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Support switching from vendor-defined device mode on G9 and G11
HID: wacom: Initialize hid_data.inputmode to -1
HID: microsoft: add support for 3 more devices
HID: multitouch: Synchronize MT frame on reset_resume
HID: wacom: fix Bamboo ONE oops
HID: lenovo: Don't use stack variables for DMA buffers
HID: usbhid: fix inconsistent reset/resume/reset-resume behavior
HID: wiimote: Fix wiimote mp scale linearization
The 'size' variable is not really needed, and we can also shift constant
in the loop body when masking off existing bits.
Also we do not have to use 64 bit calculations if we take an extra
branch.
[jkosina@suse.cz: fix a small error in changelog]
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A tablet PC booted into Windows may have its pen/touch hardware switched
into "Wacom mode" similar to what we do with explicitly-supported hardware.
Some devices appear to maintain this state across reboots, preventing their
use with the generic HID driver. This patch adds support for detecting the
presence of the mode switch feature report used by devices based on the G9
and G11 chips and has the HID codepath always attempt to reset the device
back to sending standard HID reports.
Fixes: https://sourceforge.net/p/linuxwacom/bugs/307/
Fixes: https://sourceforge.net/p/linuxwacom/bugs/310/
Fixes: https://github.com/linuxwacom/input-wacom/issues/15
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 5ae6e89 introduced hid_data.inputmode with a comment that it
would have the value -1 if undefined, but then forgot to actually
perform the initialization. Although this doesn't appear to have
caused any problems in practice, it should still be remedied.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the Micrsift Digital 4K, Media 600 and Media 3000 V1 Keyboards,
which have the same quirks as the already existing hardware MS_NE4K.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=52841
[jkosina@suse.cz: rephrase changelog]
Signed-off-by: Alistair Leslie-Hughes <leslie_alistair@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Asus X205TA and E200HA built-in keyboard contain wrong logical maximum value in
report descriptor.
This patch correct wrong logical maximum in report descriptor.
Signed-off-by: Yusuke Fujimaki <usk.fujimaki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My static checker complains that "devid" can be uninitialized if
alloc_chrdev_region() fails. Fix this by moving the error hanling
forward a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My static checker complains because we use "dev_id" before we check for
errors so it could be uninitialized. Fix this by moving the error
handling forward a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
input_mt_get_slot_by_key() requires input_mt_sync_frame() to be called
at each frame. Do it when releasing the touches, or else we won't get
a proper slot number after mt_reset_resume().
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin TIssoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like recent changes in the Wacom driver made the Bamboo ONE crashes.
The tablet behaves as if it was a regular Bamboo device with pen, touch
and pad, but there is no physical pad connected to it.
The weird part is that the pad is still sending events and given that
there is no input node connected to it, we get anull pointer exception.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317116
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The lenovo_send_cmd_cptkbd function uses a stack variable to submit
commands via hid_hw_raw_request. Eventually this gets to the
usb_hcd_map_urb_for_dma function, which causes a warning to be thrown
if the CONFIG_DMA_API_DEBUG option is enabled.
Fix this by allocating a temporary buffer instead.
[jkosina@suse.cz: no need to NULL-initialize buf, spotted by Benjamin]
Reported-by: lejeczek <peljasz@yahoo.co.uk>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Fraga <fragabr@gmail.com>
Tested-by: Daniel Fraga <fragabr@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of open-coding memory allocation and copying form user memory
sequence let's use memdup_user().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
uhid changes the format expected in write() depending on bitness. It
should check the syscall bitness directly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wiimote motion plus gyros use two scales to report fast and slow
rotation - below 440 deg/s uses 8192/440 units / deg/s, and above uses
8192/2000 units / deg/s.
Previously this driver attempted to linearize the two by scaling the fast
rate by 18 and the slow by 9, but this results in a scale of
8192*9/440 = ~167.564 for slow and 8192*18/2000 = 73.728 for fast.
Correct the fast motion scale factor so that both report ~167.564
units / deg/s
Signed-off-by: Cyan Ogilvie <cyan.ogilvie@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- functionally equivalent cleanups for wacom driver, making the code
more readable, from Benjamin Tissoires
- a bunch of improvements and fixes for thingm driver from Heiner
Kallweit
- bugfixes to out-of-bound access for generic parsing functions (which
have been there since ever) extract() and implement(), from Dmitry
Torokhov
- a lot of added / improved device support in sony, wacom, microsoft,
multitouch and logitech driver, from various people
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (44 commits)
HID: microsoft: Add ID for MS Wireless Comfort Keyboard
hid: thingm: reorder calls in thingm_probe
HID: i2c-hid: fix OOB write in i2c_hid_set_or_send_report()
HID: multitouch: Release all touch slots on reset_resume
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard2
HID: penmount: report only one button for PenMount 6000 USB touchscreen controller
HID: i2c-hid: Fix suspend/resume when already runtime suspended
HID: i2c-hid: Add hid-over-i2c name to i2c id table
HID: multitouch: force retrieving of Win8 signature blob
HID: Support for CMedia CM6533 HID audio jack controls
HID: thingm: improve locking
HID: thingm: switch to managed version of led_classdev_register
HID: thingm: remove workqueue
HID: corsair: fix mapping of non-keyboard usages
HID: wacom: close the wireless receiver on remove()
HID: wacom: cleanup input devices
HID: wacom: reuse wacom_parse_and_register() in wireless_work
HID: wacom: move down wireless_work()
HID: wacom: break out parsing of device and registering of input
HID: wacom: break out wacom_intuos_get_tool_type
...
Microsoft Wireless Comfort Keyboard has vendor specific My Favorites
1-5 keys. Linux already supports this buttons on other MS keyboards by
MS_ERGONOMY quirk. So apply MS_ERGONOMY quirk to USB PID 0x00e3
(Microsoft Wireless Optical Desktop Receiver 3.0A). After this
My Favorites 1..5 keys will be reported as KEY_F14..KEY_F15 events.
Signed-off-by: Slava Bacherikov <slava@bacher09.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When reviewing another thingm patch Benjamin Tissoires pointed out
the following: "The problem here is that hid_hw_start() is called
before thingm_version() which allows user space to briefly introduce
races between thingm_version() and any hidraw requests.
The mutex will not help here as it is initialized after hid_hw_start()
and only used for protecting the concurrent access of the rgb."
Avoid this possible issue by calling hid_hw_start() later in the
probe function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though hid_hw_* checks that passed in data_len is less than
HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily
allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device
reports and select largest size. In-kernel users normally just send as much
data as report needs, so there is no problem, but hidraw users can do
whatever they please:
BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80
Write of size 4101 by task syz-executor/8747
CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83
[<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50
[< inline >] print_error_description mm/kasan/report.c:97
[< inline >] kasan_report_error mm/kasan/report.c:278
[<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305
[<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718
[<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299
[<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178
[< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321
[<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589
[<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602
[< inline >] hid_hw_output_report include/linux/hid.h:1039
[<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154
[<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177
[<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534
[< inline >] SYSC_pwrite64 fs/read_write.c:627
[<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614
Object at ffffffc07135ea80, in cache kmalloc-512
Object allocated with size 268 bytes.
Let's check data length against the buffer size before attempting to copy
data over.
Cc: stable@vger.kernel.org
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When resetting a device (especially after power loss) it is unlikely
that the firmware will keep the contact tracking data for the previous
touches and will be able to reconcile it with the new contacts, so
let's release all slots on reset resume as start anew.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo)
with VID:PID 1a2c:0027 does not seem to be handling the reports
initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the
kernel when connected, and a delay before its initialization. It can
also cause the hang the system.
This patch adds the quirk for this device, which causes the delay
to disappear. It is named as "USB Keykoard2" because the "USB Keykoard"
already exists.
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PenMount 6000 USB resistive touchscreen controller reports it has three
buttons, while in reality it doesn't have any and doesn't support active
styli, and only generates touch events.
In penmount_input_mapping(), map only the first button (with code 0),
ignore the rest.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
Tested-by: Christian Gmeiner <c.gmeiner@bachmann.info
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ACPI-based systems ACPI power domain code runtime resumes device before
calling suspend method, which ensures that i2c-hid suspend code starts with
device not in low-power state and with interrupts enabled.
On other systems, especially if device is not a part of any power domain,
we may end up calling driver's system-level suspend routine while the
device is runtime-suspended (with controller in presumably low power state
and interrupts disabled). This will result in interrupts being essentially
disabled twice, and we will only re-enable them after both system resume
and runtime resume methods complete. Unfortunately i2c_hid_resume() calls
i2c_hid_hwreset() and that only works properly if interrupts are enabled.
Also if device is runtime-suspended driver's suspend code may fail if it
tries to issue I/O requests.
Let's fix it by runtime-resuming the device if we need to run HID driver's
suspend code and also disabling interrupts only if device is not already
runtime-suspended. Also on resume we mark the device as running at full
power (since that is what resetting will do to it).
Reviewed-by: Benson Leung <bleung@chromium.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When using the device tree binding OF compatible = "hid-over-i2c" the
i2c id table also needs to have that name in order to auto load this
driver, since i2c core reports module alias as i2c:<string> where
<string> is compatible string of OF binding stripped of manufacturer's
prefix.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Synaptics 0x11e5 over I2C found in the Asus T100-CHI requires to
fetch the signature blob to actually start sending events.
With this patch, we should be close enough to the Windows driver which
checks the content of the blob at plugin to validate or not the
touchscreen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=113481
Fixes: 6d4f5440 ("HID: multitouch: Fetch feature reports on demand for Win8 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The C-Media CM6533 is a USB audio chip featuring it's jack detection
capability.The device originates an interrupt transfer via HID interface each
time when a jack event occurs. The purpose of this patch is to handle hid raw
events to keep the operating system informed of user interactions.
Signed-off-by: Ben Chen <ben_chen@bizlinktech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading from the device consists of two operations: sending the read
command and the actual read from the device. If the device is accessed
in between we might read wrong data. Therefore protect the full sequence
of both operations with a mutex.
Also change the semantics of thingm_recv to include both operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplify the code by switching to the managed version of
led_classdev_register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defining workqueues in LED drivers isn't needed any longer as the LED core
was extended with a generic workqueue recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes a bug where the Volume Up key was ignored because it uses the same usage code as G18. Special Corsair usage codes are in the keyboard page, other pages should be left to the generic driver.
Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
rmmod/insmod the wacom.ko module does not work for the receiver because
it was not previously closed. Now, we can hack with the wireless receiver
without having to unplug/replug it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just some cleaning up when the input devices are unregistered.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes duplicated code.
The only difference is that we now need to stop and start the attached hid
device, but this is a small cost.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wireless_work() wants to reuse parse_and_register(), we need to have
it declared after this function.
No functional changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies the .probe() and will allow to reuse this path in the future.
Few things are reshuffled in .probe():
- init wacom struct earlier
- then retrieve the report descriptor
- then parse it and allocate/register inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow to reuse the code in a later series and simplifies
the reading of wacom_intuos_inout().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ignore_special_drivers works fine until hid_scan_report autodetects and
reassign devices (for hid-multitouch, hid-microsoft and hid-rmi).
Simplify the handling of the parameter: if it is there, use hid-generic, no
matter what, and if not, scan the device or rely on the hid_have_special_driver
table.
This was detected while trying to disable hid-multitouch on a Surface Pro cover
which prevented to use the keyboard.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The patch that added Logitech Dual Action gamepad support forgot to
update the special driver list for the device. This caused the logitech
driver not to probe unless kernel module load order was favorable.
Update the special driver list to fix it. Thanks to Simon Wood for the
idea.
Cc: Vitaly Katraew <zawullon@gmail.com>
Fixes: 56d0c8b7c8 ("HID: add support for Logitech Dual Action gamepads")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Double-underscore prefixed types are unnecessary in pure kernel code,
replace them with the non prefixed equivalents.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WARNING: Block comments use a trailing */ on a separate line
#822: FILE: drivers/hid/hid-sony.c:822:
+ * number but it's not needed for correct operation */
WARNING: Block comments use a trailing */ on a separate line
#828: FILE: drivers/hid/hid-sony.c:828:
+ * buttons multiple keypresses are allowed */
WARNING: Block comments use a trailing */ on a separate line
#854: FILE: drivers/hid/hid-sony.c:854:
+ * 0xff and 11th is for press indication */
WARNING: Missing a blank line after declarations
#1930: FILE: drivers/hid/hid-sony.c:1930:
+ struct sony_sc *sc = container_of(work, struct sony_sc, state_worker);
+ sc->send_output_report(sc);
WARNING: Block comments use a trailing */ on a separate line
#2510: FILE: drivers/hid/hid-sony.c:2510:
+ * Logitech joystick from the device descriptor. */
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
./scripts/checkpatch.pl \
--types "SPACING,TRAILING_WHITESPACE,POINTER_LOCATION,CODE_INDENT" \
-f drivers/hid/hid-sony.c
ERROR: trailing whitespace
#933: FILE: drivers/hid/hid-sony.c:933:
+^I * $
ERROR: space prohibited after that open square bracket '['
#947: FILE: drivers/hid/hid-sony.c:947:
+ [ 1] = BTN_TRIGGER_HAPPY1,
ERROR: space prohibited after that open square bracket '['
#948: FILE: drivers/hid/hid-sony.c:948:
+ [ 2] = BTN_TRIGGER_HAPPY2,
ERROR: space prohibited after that open square bracket '['
#949: FILE: drivers/hid/hid-sony.c:949:
+ [ 3] = BTN_TRIGGER_HAPPY3,
ERROR: space prohibited after that open square bracket '['
#950: FILE: drivers/hid/hid-sony.c:950:
+ [ 4] = BTN_TRIGGER_HAPPY4,
ERROR: space prohibited after that open square bracket '['
#951: FILE: drivers/hid/hid-sony.c:951:
+ [ 5] = BTN_TRIGGER_HAPPY5,
ERROR: space prohibited after that open square bracket '['
#952: FILE: drivers/hid/hid-sony.c:952:
+ [ 6] = BTN_TRIGGER_HAPPY6,
ERROR: space prohibited after that open square bracket '['
#953: FILE: drivers/hid/hid-sony.c:953:
+ [ 7] = BTN_TRIGGER_HAPPY7,
ERROR: space prohibited after that open square bracket '['
#954: FILE: drivers/hid/hid-sony.c:954:
+ [ 8] = BTN_TRIGGER_HAPPY8,
ERROR: space prohibited after that open square bracket '['
#955: FILE: drivers/hid/hid-sony.c:955:
+ [ 9] = BTN_TRIGGER_HAPPY9,
ERROR: "(foo*)" should be "(foo *)"
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
WARNING: missing space after return type
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
ERROR: "(foo*)" should be "(foo *)"
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
WARNING: missing space after return type
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
ERROR: code indent should use tabs where possible
#2449: FILE: drivers/hid/hid-sony.c:2449:
+ */$
total: 13 errors, 2 warnings, 2570 lines checked
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds a warning message stating that the sysfs group was not able to be
created for the passed hid_device structure pointer with dev_warn.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Benjamin Tissoires <benajmin.tissoires@redhat.com>
[jkosina@suse.cz: massaged changelog a bit]
[jkosina@suse.cz: reformatted source]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The midi controller times-out while initializing reports, this
causes boot to take an extra 10 seconds. The device descriptor
advertises that it has an internal HID device but seems to not
actually do anything useful.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp_ff_init() and hidpp_ff_deinit() are not used outside of
hid-logitech-hidpp.c, so let's make them static.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements force feedback support for the Logitech
G920 Driving Force Racing Wheel. It is a generic implementation
of feature 0x8123 of the Logitech HID++ protocol and should be
usable for any future devices that implement this feature.
This patch should be applied after the basic G920 support patch
by Simon Wood:
http://www.spinics.net/lists/linux-input/msg42174.html
The driving supports everything that is supported by the G920
firmware:
FF_CONSTANT
FF_PERIODIC
FF_SINE
FF_SQUARE
FF_SAW_UP
FF_SAW_DOWN
FF_TRIANGLE
FF_SPRING
FF_DAMPER
FF_AUTOCENTER
FF_GAIN
and for version 2 firmware also:
FF_FRICTION
FF_INERTIA
FF_RAMP
Both envelopes and replay values are supported as well, but some
problems may occur when using firmware release 1. There is also a
small residual clockwise damper in the wheel when using the first
firmware release. All problems are fixed in the soon te be released
firmware version 2.
The default spring is disabled by permanently placing a spring
force in the wheel. This spring is also used as the autocenter
spring.
Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck
in XBox since the xpad changes where not included). Michal has an
alternative approach documented here (and the changes should be submitted
upstream to usb_modeswitch project):
===
Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the
following content:
DefaultVendor=046d
DefaultProduct=c261
MessageEndpoint=01
ResponseEndpoint=01
TargetClass=0x03
MessageContent="0f00010142"
Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and
watch the magic happen:)
===
[jkosina@suse.cz: added information about mode switching from Simon]
[jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon]
[jkosina@suse.cz: fix merge conflict due to to_hid_device() changes]
Signed-off-by: Edwin Velds <e.velds@gmail.com>
Tested-by: Elias Vanderstuyft <elias.vds@gmail.com>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 0925636042 ("HID: rmi: Disable scanning if the device is not a wake
source") introduced a regression for devices which use hid-rmi to handle
composite USB devices. The suspend or resume callbacks are not checking
that the device is a RMI device before calling rmi_read or rmi_write.
This results in dereferencing uninitialized variables on non RMI devices. This
patch checks that the RMI_DEVICE flag is set before sending RMI commands to the
device.
Reported-by: Rodrigo Gomes <rodrigo.toste.gomes@gmail.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The correct product ID for the old version of the raphnet 4nes4snes
device was 0x0a9d, not 0x0a8d.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Benjamin Tissoires