[ Upstream commit 559c36c5a8 ]
nf_osf_find() incorrectly returns true on mismatch, this leads to
copying uninitialized memory area in nft_osf which can be used to leak
stale kernel stack data to userspace.
Fixes: 22c7652cda ("netfilter: nft_osf: Add version option support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8d5dfd1d8 ]
CTCP messages should only be at the start of an IRC message, not
anywhere within it.
While the helper only decodes packes in the ORIGINAL direction, its
possible to make a client send a CTCP message back by empedding one into
a PING request. As-is, thats enough to make the helper believe that it
saw a CTCP message.
Fixes: 869f37d8e4 ("[NETFILTER]: nf_conntrack/nf_nat: add IRC helper port")
Signed-off-by: David Leadbeater <dgl@dgl.cx>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39aebedeaa ]
ct_sip_next_header and ct_sip_get_header return an absolute
value of matchoff, not a shift from current dataoff.
So dataoff should be assigned matchoff, not incremented by it.
This issue can be seen in the scenario when there are multiple
Contact headers and the first one is using a hostname and other headers
use IP addresses. In this case, ct_sip_walk_headers will work as follows:
The first ct_sip_get_header call to will find the first Contact header
but will return -1 as the header uses a hostname. But matchoff will
be changed to the offset of this header. After that, dataoff should be
set to matchoff, so that the next ct_sip_get_header call find the next
Contact header. But instead of assigning dataoff to matchoff, it is
incremented by it, which is not correct, as matchoff is an absolute
value of the offset. So on the next call to the ct_sip_get_header,
dataoff will be incorrect, and the next Contact header may not be
found at all.
Fixes: 05e3ced297 ("[NETFILTER]: nf_conntrack_sip: introduce SIP-URI parsing helper")
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a994b34b9a ]
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220827175140.1696699-1-festevam@denx.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8123437cf4 ]
We've found the AUX channel to be less reliable with PCLK_EDP at a
higher rate (typically 25 MHz). This is especially important on systems
with PSR-enabled panels (like Gru-Kevin), since we make heavy, constant
use of AUX.
According to Rockchip, using any rate other than 24 MHz can cause
"problems between syncing the PHY an PCLK", which leads to all sorts of
unreliabilities around register operations.
Fixes: d67a38c5a6 ("arm64: dts: rockchip: move core edp from rk3399-kevin to shared chromebook")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220830131212.v2.1.I98d30623f13b785ca77094d0c0fd4339550553b6@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5467359a7 ]
The Gru-Bob board does not have a pull-up resistor on its
WLAN_HOST_WAKE# pin, but Kevin does. The production/vendor kernel
specified the pin configuration correctly as a pull-up, but this didn't
get ported correctly to upstream.
This means Bob's WLAN_HOST_WAKE# pin is floating, causing inconsistent
wakeup behavior.
Note that bt_host_wake_l has a similar dynamic, but apparently the
upstream choice was to redundantly configure both internal and external
pull-up on Kevin (see the "Kevin has an external pull up" comment in
rk3399-gru.dtsi). This doesn't cause any functional problem, although
it's perhaps wasteful.
Fixes: 8559bbeeb8 ("arm64: dts: rockchip: add Google Bob")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220822164453.1.I75c57b48b0873766ec993bdfb7bc1e63da5a1637@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5f56a74cc0 upstream.
We currently check the MokSBState variable to decide whether we should
treat UEFI secure boot as being disabled, even if the firmware thinks
otherwise. This is used by shim to indicate that it is not checking
signatures on boot images. In the kernel, we use this to relax lockdown
policies.
However, in cases where shim is not even being used, we don't want this
variable to interfere with lockdown, given that the variable may be
non-volatile and therefore persist across a reboot. This means setting
it once will persistently disable lockdown checks on a given system.
So switch to the mirrored version of this variable, called MokSBStateRT,
which is supposed to be volatile, and this is something we can check.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1885ff13d4 upstream.
Just as with the 5570 (and the other Dell laptops), this enables the two
subwoofer speakers on the Dell Precision 5530 together with the main
ones, significantly increasing the audio quality. I've tested this
myself on a 5530 and can confirm it's working as expected.
Signed-off-by: Callum Osmotherly <callum.osmotherly@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YyMjQO3mhyXlMbCf@piranha
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba1f818053 upstream.
The ASUS G15 2022 (GA503R) series laptop has the same node-to-DAC pairs
as early models and the G14, this includes bass speakers which are by
default mapped incorrectly to the 0x06 node.
Add a quirk to use the same DAC pairs as the G14.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-4-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc2c23549c upstream.
Fixes up the pincfg for ASUS ROG Strix G15 (G533Z) headphone combo jack
[ Fixed the position in the quirk table by tiwai ]
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-3-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c611e65904 upstream.
Fixes up the pincfg for ASUS ROG Strix G513 headphone and mic combo jack
[ Fixed the position in the quirk table by tiwai ]
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915080921.35563-2-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16c8f229a upstream.
A few entries have been mistakenly inserted in wrong positions without
considering the SSID ordering. Place them at right positions.
Fixes: b7557267c2 ("ALSA: hda/realtek: Add quirk for ASUS GA402")
Fixes: 94db9cc8f8 ("ALSA: hda/realtek: Add quirk for ASUS GU603")
Fixes: 739d0959fb ("ALSA: hda: Add quirk for ASUS Flow x13")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220915154724.31634-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe0a2ac7c6 ]
This reverts commit 8cb339f1c1 as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1c1 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58bfe7d8e3 ]
This reverts commit 3d5f70949f.
The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f70949f ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b46a6b09fa ]
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d5f70949f ]
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:
Timeout while waiting for setup device command
device not accepting address X, error -62
unable to enumerate USB device
By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220824191320.17883-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 692a8ebcfc ]
Whenever the atmel_rs485_config() driver method would be called,
the USART mode is reset to normal mode before even checking if
RS485 flag is set, thus resulting in losing the previous USART
mode in the case where the checking fails.
Some tools, such as `linux-serial-test`, lead to the driver calling
this method when doing the setup of the serial port: after setting the
port mode (Hardware Flow Control, Normal Mode, RS485 Mode, etc.),
`linux-serial-test` tries to enable/disable RS485 depending on
the commandline arguments that were passed.
Example of how this issue could reveal itself:
When doing a serial communication with Hardware Flow Control through
`linux-serial-test`, the tool would lead to the driver roughly doing
the following:
- set the corresponding bit to 1 (ATMEL_US_USMODE_HWHS bit in the
ATMEL_US_MR register) through the atmel_set_termios() to enable
Hardware Flow Control
- disable RS485 through the atmel_config_rs485() method
Thus, when the latter is called, the mode will be reset and the
previously set bit is unset, leaving USART in normal mode instead of
the expected Hardware Flow Control mode.
This fix ensures that this reset is only done if the checking for
RS485 succeeds and that the previous mode is preserved otherwise.
Fixes: e8faff7330 ("ARM: 6092/1: atmel_serial: support for RS485 communications")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Link: https://lore.kernel.org/r/20220824142902.502596-1-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60efd05139 ]
In uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port.
So remove the assignment from the drivers rs485_config() function to avoid
redundancy.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-10-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 692a8ebcfc ("tty: serial: atmel: Preserve previous USART mode if RS485 disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 477b838310 ]
At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
Register are empty, even though TXRDY might be up and controller is able to
receive data. Since the controller sends data only when TXEMPTY is ready,
on RS485, when DMA is not used, the RTS pin is driven low after each byte.
With this patch, the characters will be transmitted when TXRDY is up and
so, RTS pin will remain high between bytes.
The performance improvement on RS485 is about 8% with a baudrate of 300.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200107111656.26308-1-codrin.ciubotariu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 692a8ebcfc ("tty: serial: atmel: Preserve previous USART mode if RS485 disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60deb9f10e ]
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?extid=f9acff9bf08a845f225d
Reported-by: syzbot+f9acff9bf08a845f225d@syzkaller.appspotmail.com
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Link: https://lore.kernel.org/r/20220819200340.34826-1-code@siddh.me
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548011957d ]
Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.
This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.
Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133937.1.Ia8174b875bc926c12ce427a5a1415dea31cc35ae@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bf661daf6 ]
In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."
Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/5b9ff09f53d23cf9e5c5437db4ffc18b798bf60c.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 548011957d ("usb: xhci-mtk: relax TT periodic bandwidth allocation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c986fbc16 ]
Tune the boundary for FS/LS ESIT due to CS:
For ISOC out-ep, the controller starts transfer data after
the first SS; for others, the data is already transferred
before the last CS.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/49e5a269a47984f3126a70c3fb471b0c2874b8c2.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 548011957d ("usb: xhci-mtk: relax TT periodic bandwidth allocation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 040f2dbd20 ]
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8034f493 ]
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e131d1ac ]
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0066472de1 ]
It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8217f07a50 ]
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd20 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 51bdc8bb82 upstream.
The newly added stac_check_power_status() caused a compile warning
when CONFIG_SND_HDA_INPUT_BEEP is disabled. Fix it.
Fixes: 414d38ba87 ("ALSA: hda/sigmatel: Keep power up while beep is enabled")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220905130630.2845-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a09d2d00af ]
In pxa3xx_gcu_write, a count parameter of type size_t is passed to words of
type int. Then, copy_from_user() may cause a heap overflow because it is used
as the third argument of copy_from_user().
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c17a253870 ]
When System.map was generated, the kernel used mksysmap to filter the
kernel symbols, we need to filter "L0" symbols in LoongArch architecture.
$ cat System.map | grep L0
9000000000221540 t L0
The L0 symbol exists in System.map, but not in .tmp_System.map. When
"cmp -s System.map .tmp_System.map" will show "Inconsistent kallsyms
data" error message in link-vmlinux.sh script.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba912afbd6 ]
For irq_domain_associate() to work the virq descriptor has to be
pre-allocated in advance. Otherwise the following happens:
WARNING: CPU: 0 PID: 0 at .../kernel/irq/irqdomain.c:527 irq_domain_associate+0x298/0x2e8
error: virq128 is not allocated
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.78-... #1
...
Call Trace:
[<ffffffff801344c4>] show_stack+0x9c/0x130
[<ffffffff80769550>] dump_stack+0x90/0xd0
[<ffffffff801576d0>] __warn+0x118/0x130
[<ffffffff80157734>] warn_slowpath_fmt+0x4c/0x70
[<ffffffff801b83c0>] irq_domain_associate+0x298/0x2e8
[<ffffffff80a43bb8>] octeon_irq_init_ciu+0x4c8/0x53c
[<ffffffff80a76cbc>] of_irq_init+0x1e0/0x388
[<ffffffff80a452cc>] init_IRQ+0x4c/0xf4
[<ffffffff80a3cc00>] start_kernel+0x404/0x698
Use irq_alloc_desc_at() to avoid the above problem.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0066f1b0e2 ]
When trying to get a file lock on an AFS file, the server may return
UAEAGAIN to indicate that the lock is already held. This is currently
translated by the default path to -EREMOTEIO.
Translate it instead to -EAGAIN so that we know we can retry it.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey E Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/166075761334.3533338.2591992675160918098.stgit@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d44e6044a ]
AZA HW may send a burst read/write request crossing 4K memory boundary.
The 4KB boundary is not guaranteed by Tegra HDA HW. Make SW change to
include the flag AZX_DCAPS_4K_BDLE_BOUNDARY to align BDLE to 4K
boundary.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220905172420.3801-1-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
