rasize (ra_pages) should be set higher than read size by default
to allow parallel reads when reading large files in order to
improve performance (otherwise there is much dead time on the
network when doing readahead of large files). Default rasize
to twice readsize.
Signed-off-by: Steve French <stfrench@microsoft.com>
When a tick broadcast clockevent device is initialized for one shot mode
then tick_broadcast_setup_oneshot() OR's the periodic broadcast mode
cpumask into the oneshot broadcast cpumask.
This is required when switching from periodic broadcast mode to oneshot
broadcast mode to ensure that CPUs which are waiting for periodic
broadcast are woken up on the next tick.
But it is subtly broken, when an active broadcast device is replaced and
the system is already in oneshot (NOHZ/HIGHRES) mode. Victor observed
this and debugged the issue.
Then the OR of the periodic broadcast CPU mask is wrong as the periodic
cpumask bits are sticky after tick_broadcast_enable() set it for a CPU
unless explicitly cleared via tick_broadcast_disable().
That means that this sets all other CPUs which have tick broadcasting
enabled at that point unconditionally in the oneshot broadcast mask.
If the affected CPUs were already idle and had their bits set in the
oneshot broadcast mask then this does no harm. But for non idle CPUs
which were not set this corrupts their state.
On their next invocation of tick_broadcast_enable() they observe the bit
set, which indicates that the broadcast for the CPU is already set up.
As a consequence they fail to update the broadcast event even if their
earliest expiring timer is before the actually programmed broadcast
event.
If the programmed broadcast event is far in the future, then this can
cause stalls or trigger the hung task detector.
Avoid this by telling tick_broadcast_setup_oneshot() explicitly whether
this is the initial switch over from periodic to oneshot broadcast which
must take the periodic broadcast mask into account. In the case of
initialization of a replacement device this prevents that the broadcast
oneshot mask is modified.
There is a second problem with broadcast device replacement in this
function. The broadcast device is only armed when the previous state of
the device was periodic.
That is correct for the switch from periodic broadcast mode to oneshot
broadcast mode as the underlying broadcast device could operate in
oneshot state already due to lack of periodic state in hardware. In that
case it is already armed to expire at the next tick.
For the replacement case this is wrong as the device is in shutdown
state. That means that any already pending broadcast event will not be
armed.
This went unnoticed because any CPU which goes idle will observe that
the broadcast device has an expiry time of KTIME_MAX and therefore any
CPUs next timer event will be earlier and cause a reprogramming of the
broadcast device. But that does not guarantee that the events of the
CPUs which were already in idle are delivered on time.
Fix this by arming the newly installed device for an immediate event
which will reevaluate the per CPU expiry times and reprogram the
broadcast device accordingly. This is simpler than caching the last
expiry time in yet another place or saving it before the device exchange
and handing it down to the setup function. Replacement of broadcast
devices is not a frequent operation and usually happens once somewhere
late in the boot process.
Fixes: 9c336c9935 ("tick/broadcast: Allow late registered device to enter oneshot mode")
Reported-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/87pm7d2z1i.ffs@tglx
"SHAREFLAG_ISOLATED_TRANSPORT" indicates that we should not reuse the socket
for this share (for future mounts). Mark the socket as server->nosharesock if
share flags returned include SHAREFLAG_ISOLATED_TRANSPORT.
See MS-SMB2 MS-SMB2 2.2.10 and 3.2.5.5
Signed-off-by: Steve French <stfrench@microsoft.com>
Change type of pcchunk->Length from u32 to u64 to match
smb2_copychunk_range arguments type. Fixes the problem where performing
server-side copy with CIFS_IOC_COPYCHUNK_FILE ioctl resulted in incomplete
copy of large files while returning -EINVAL.
Fixes: 9bf0c9cd43 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files")
Cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Witek <pawel.ireneusz.witek@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The #if check is wrong, leading to a build failure:
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c: In function 'mxc_isi_channel_set_inbuf':
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:33:5: error: "CONFIG_ARCH_DMA_ADDR_T_64BIT" is not defined, evaluates to 0 [-Werror=undef]
33 | #if CONFIG_ARCH_DMA_ADDR_T_64BIT
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
This could just be an #ifdef, but it seems nicer to just remove the
check entirely. Apparently the only reason for the #ifdef is to avoid
another warning:
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:55:24: error: right shift count >= width of type [-Werror=shift-count-overflow]
But this is best avoided by using the lower_32_bits()/upper_32_bits()
helpers.
Fixes: cf21f328fc ("media: nxp: Add i.MX8 ISI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This id was removed in commit b47018a778 ("platform/x86: intel_scu_ipc:
Remove Lincroft support"), saying it is only used on Moorestown,
but apparently the same id is also used on Medfield.
Tested on the Medfield based Motorola RAZR i smartphone.
Signed-off-by: Julian Winkler <julian.winkler1@web.de>
Link: https://lore.kernel.org/r/20230416154932.6579-1-julian.winkler1@web.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Even when urgent BKOPS fails, the consumer will get stuck in runtime
suspend status. Like commit 1a5665fc8d ("scsi: ufs: core: WLUN suspend
SSU/enter hibern8 fail recovery"), trigger the error handler and return
-EBUSY to break the suspend.
Fixes: b294ff3e34 ("scsi: ufs: core: Enable power management for wlun")
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Link: https://lore.kernel.org/r/20230425031721epcms2p5d4de65616478c967d466626e20c42a3a@epcms2p5
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When CONFIG_OF is disabled, the 'data' variable is not used at all
because of_match_node() turns into a dummy macro:
drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.c: In function 'mdp_comp_sub_create':
drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.c:1038:36: error: unused variable 'data' [-Werror=unused-variable]
1038 | const struct mtk_mdp_driver_data *data = mdp->mdp_data;
| ^~~~
Remove the variable again by moving the pointer dereference into the
of_match_node call.
Fixes: b385b991ef ("media: platform: mtk-mdp3: chip config split about subcomponents")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
gcc warns about some functions being unused when CONFIG_PM_SLEEP
is disabled:
drivers/media/platform/nxp/imx8-isi/imx8-isi-core.c:328:12: error: 'mxc_isi_pm_resume' defined but not used [-Werror=unused-function]
328 | static int mxc_isi_pm_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~
drivers/media/platform/nxp/imx8-isi/imx8-isi-core.c:314:12: error: 'mxc_isi_pm_suspend' defined but not used [-Werror=unused-function]
314 | static int mxc_isi_pm_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~
Use the modern SYSTEM_SLEEP_PM_OPS()/RUNTIME_PM_OPS() helpers in place
of the old SET_SYSTEM_SLEEP_PM_OPS()/SET_RUNTIME_PM_OPS() ones.
By convention, use pm_ptr() to guard the reference to the operations.
This makes no difference as long as the driver requires CONFIG_PM,
but is what users of SET_RUNTIME_PM_OPS() are supposed to do.
Fixes: cf21f328fc ("media: nxp: Add i.MX8 ISI driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When doing format validation for NV12 the width and height should be
aligned to 32 pixels.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The VIN modules on Gen3 can not scale NV12, fail format validation if
the user tries. Currently no frames are produced if this is attempted.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit de614ac319 ("MAINTAINERS: Add entries for Apple PWM driver") adds
an entry for Documentation/devicetree/bindings/pwm/pwm-apple.yaml, but
commit 87a3a3929c ("dt-bindings: pwm: Add Apple PWM controller") from
the same patch series actually adds the devicetree binding file with the
name apple,s5l-fpwm.yaml.
Adjust the file entry to the file actually added.
Fixes: de614ac319 ("MAINTAINERS: Add entries for Apple PWM driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230424114043.22475-1-lukas.bulwahn@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Commit
310e782a99 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")
switched to using amd_smn_read() which relies upon the misc PCI ID used
by DF function 3 being included in a table. The ID for model 78h is
missing in that table, so amd_smn_read() doesn't work.
Add the missing ID into amd_nb, restoring s2idle on this system.
[ bp: Simplify commit message. ]
Fixes: 310e782a99 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230427053338.16653-2-mario.limonciello@amd.com
Fix kernel-doc warnings for cid_lock and use_cid_lock.
These comments are not in kernel-doc format.
kernel/sched/core.c:11496: warning: Cannot understand * @cid_lock: Guarantee forward-progress of cid allocation.
on line 11496 - I thought it was a doc line
kernel/sched/core.c:11505: warning: Cannot understand * @use_cid_lock: Select cid allocation behavior: lock-free vs spinlock.
on line 11505 - I thought it was a doc line
Fixes: 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230428031111.322-1-rdunlap@infradead.org
Several similar kernel warnings can be triggered,
[56605.607840] CPU0 PEBS record size 0, expected 32, config 0 cpuc->record_size=208
when the below commands are running in parallel for a while on SPR.
while true;
do
perf record --no-buildid -a --intr-regs=AX \
-e cpu/event=0xd0,umask=0x81/pp \
-c 10003 -o /dev/null ./triad;
done &
while true;
do
perf record -o /tmp/out -W -d \
-e '{ld_blocks.store_forward:period=1000000, \
MEM_TRANS_RETIRED.LOAD_LATENCY:u:precise=2:ldlat=4}' \
-c 1037 ./triad;
done
The triad program is just the generation of loads/stores.
The warnings are triggered when an unexpected PEBS record (with a
different config and size) is found.
A system-wide PEBS event with the large PEBS config may be enabled
during a context switch. Some PEBS records for the system-wide PEBS
may be generated while the old task is sched out but the new one
hasn't been sched in yet. When the new task is sched in, the
cpuc->pebs_record_size may be updated for the per-task PEBS events. So
the existing system-wide PEBS records have a different size from the
later PEBS records.
The PEBS buffer should be flushed right before the hardware is
reprogrammed. The new size and threshold should be updated after the
old buffer has been flushed.
Reported-by: Stephane Eranian <eranian@google.com>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230421184529.3320912-1-kan.liang@linux.intel.com
It missed to convert a PERF_SAMPLE_BRANCH_STACK user to call the new
perf_sample_save_brstack() helper in order to update the dyn_size.
This affects AMD Zen3 machines with the branch-brs event.
Fixes: eb55b455ef ("perf/core: Add perf_sample_save_brstack() helper")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230427030527.580841-1-namhyung@kernel.org
Apparently despite it being marked inline, the compiler
may not inline __down_read_common() which makes it difficult
to identify the cause of lock contention, as the blocked
function in traceevents will always be listed as
__down_read_common().
So this patch adds __always_inline annotation to the common
function (as well as the inlined helper callers) to force it to
be inlined so the blocking function will be listed (via Wchan)
in traceevents.
Fixes: c995e638cc ("locking/rwsem: Fold __down_{read,write}*()")
Reported-by: Tim Murray <timmurray@google.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230503023351.2832796-1-jstultz@google.com
When adapting the original doc conversion to support 2 lanes, minItems
should've been added as well since the sensor supports either 1 or 2
lanes. Add minItems to make the validation happy again.
Fixes: 8d561d78ae ("media: dt-bindings: ov2685: convert to dtschema")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230419-ov2685-dtschema-fixup-v1-1-c850a34b3a26@z3ntu.xyz
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
When we enable MMP in ext4_multi_mount_protect() during mount or
remount, we end up calling sb_start_write() from write_mmp_block(). This
triggers lockdep warning because freeze protection ranks above s_umount
semaphore we are holding during mount / remount. The problem is harmless
because we are guaranteed the filesystem is not frozen during mount /
remount but still let's fix the warning by not grabbing freeze
protection from ext4_multi_mount_protect().
Cc: stable@kernel.org
Reported-by: syzbot+6b7df7d5506b32467149@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=ab7e5b6f400b7778d46f01841422e5718fb81843
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230411121019.21940-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCZFbCXwAKCRCyPKLppCJ+
J7cHAP97erKY4hBXArjpfzcvpFmboh/oqhbTLntyIpS6TEnOyQEAyervAPGIjQYC
DCo4foyXmOWn3dhNtK9M+YiRl3o2SgQ=
=7G78
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.
Build:
- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.
It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.
libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.
Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.
- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.
- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:
$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)
- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.
- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.
- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.
- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:
Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev
- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.
perf BPF filters:
- New feature where BPF can be used to filter samples, for instance:
$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)
- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:
Essentially the BPF filter expression is:
<term> <operator> <value> (("," | "||") <term> <operator> <value>)*
The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops
The <operator> can be one of:
==, !=, >, >=, <, <=, &
The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)
perf lock contention:
- Show lock type with address.
- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:
$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80
- Update default map size to 16384.
- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.
- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).
- Fix problems found with MSAn.
perf report/top:
- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.
- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.
perf sched:
- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d4 ("perf sched: Prefer sched_waking event when it
exists").
perf ftrace:
- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:
# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#
perf top:
- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.
- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.
perf annotate:
- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.
perf kvm:
- Add TUI mode for 'perf kvm stat report'.
Reference counting:
- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.
To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:
https://perf.wiki.kernel.org/index.php/Reference_Count_Checking
- The above caught, for instance, fix, present in this series:
- Fix maps use after put in 'perf test "Share thread maps"':
'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.
Fixed by reversing the order of puts so that the leader is put
last.
- Also several fixes were made to places where reference counts were
not being held.
- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.
ARM64:
- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.
- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".
arm64 vendor events:
- Add N1 metrics.
Intel vendor events:
- Add graniterapids, grandridge and sierraforrest events.
- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp
- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.
perf stat:
- Implement --topdown using JSON metrics.
- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.
- Use metrics for --smi-cost.
- Update topdown documentation.
Vendor events (JSON) infrastructure:
- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:
{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},
- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.
- Support for printing metric thresholds in 'perf list'.
- Add --metric-no-threshold option to 'perf stat'.
- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.
- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.
S/390:
- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).
- Add cache metrics for z13, z14, z15 and z16.
- Add metric for TLB and cache.
ARM:
- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.
Intel PT hardware tracing:
- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.
- Add support for new branch instructions ERETS and ERETU.
- Fix CYC timestamps after standalone CBR
ARM CoreSight hardware tracing:
- Allow user to override timestamp and contextid settings.
- Fix segfault in dso lookup.
- Fix timeless decode mode detection.
- Add separate decode paths for timeless and per-thread modes.
auxtrace:
- Fix address filter entire kernel size.
Miscellaneous:
- Fix use-after-free and unaligned bugs in the PLT handling routines.
- Use zfree() to reduce chances of use after free.
- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.
- Suppress massive unsupported target platform errors in the unwind
code.
- Fix return incorrect build_id size in elf_read_build_id().
- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .
- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.
- Add 'perf bench syscall fork' benchmark.
- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.
- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.
- Fix some spelling mistakes"
* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...
The recent fix to ensure atomicity of lookup and allocation inadvertently
broke the pool refill mechanism, so that debugobject OOMs now in certain
situations. The reason is that the functions which got updated no longer
invoke debug_objecs_init(), which is now the only place to care about
refilling the tracking object pool.
Restore the original behaviour by adding explicit refill opportunities to
those places.
-----BEGIN PGP SIGNATURE-----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=/0Kc
-----END PGP SIGNATURE-----
Merge tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull debugobjects fix from Thomas Gleixner:
"A single fix for debugobjects:
The recent fix to ensure atomicity of lookup and allocation
inadvertently broke the pool refill mechanism, so that debugobject
OOMs now in certain situations. The reason is that the functions which
got updated no longer invoke debug_objecs_init(), which is now the
only place to care about refilling the tracking object pool.
Restore the original behaviour by adding explicit refill opportunities
to those places"
* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debugobject: Ensure pool refill (again)
- A long-standing bug in crypto_engine.
- A buggy but harmless check in the sun8i-ss driver.
- A regression in the CRYPTO_USER interface.
-----BEGIN PGP SIGNATURE-----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=9Us7
-----END PGP SIGNATURE-----
Merge tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- A long-standing bug in crypto_engine
- A buggy but harmless check in the sun8i-ss driver
- A regression in the CRYPTO_USER interface
* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix CRYPTO_USER checks for report function
crypto: engine - fix crypto_queue backlog handling
crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
- Revert an i.MX patch that's causing video failures because division
math goes sideways
- Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit
variable instead of the usual u64 type
- Fix a Kconfig bug in the StarFive JH7110 clk config that selects a
reset controller when it can't be selected
-----BEGIN PGP SIGNATURE-----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=IxvN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple more patches that would be good to get into -rc1:
- Revert an i.MX patch that's causing video failures because division
math goes sideways
- Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit
variable instead of the usual u64 type
- Fix a Kconfig bug in the StarFive JH7110 clk config that selects a
reset controller when it can't be selected"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: starfive: Fix RESET_STARFIVE_JH7110 can't be selected in a specified case
clk: sp7021: Adjust width of _m in HWM_FIELD_PREP()
Revert "clk: imx: composite-8m: Add support to determine_rate"
Convert omap and pcc to use mbox_bind_client
- omap and hi6220 : use of_property_read_bool
- test: fix double-free and use spinlock header
- rockchip and bcm-pdc: drop of_match_ptr
- mpfs: change config symbol
- mediatek gce: support MT6795
- qcom apcs: consolidate of_device_id
support IPQ9574
-----BEGIN PGP SIGNATURE-----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=NHj4
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- mailbox api: allow direct registration to a channel and convert omap
and pcc to use mbox_bind_client
- omap and hi6220 : use of_property_read_bool
- test: fix double-free and use spinlock header
- rockchip and bcm-pdc: drop of_match_ptr
- mpfs: change config symbol
- mediatek gce: support MT6795
- qcom apcs: consolidate of_device_id and support IPQ9574
* tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt-bindings: mailbox: qcom: add compatible for IPQ9574 SoC
mailbox: qcom-apcs-ipc: do not grow the of_device_id
dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants
dt-bindings: mailbox: mediatek,gce-mailbox: Add support for MT6795
mailbox: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
mailbox: bcm-pdc: drop of_match_ptr for ID table
mailbox: rockchip: drop of_match_ptr for ID table
mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()
mailbox: mailbox-test: Explicitly include header for spinlock support
mailbox: Use of_property_read_bool() for boolean properties
mailbox: pcc: Use mbox_bind_client
mailbox: omap: Use mbox_bind_client
mailbox: Allow direct registration to a channel
-----BEGIN PGP SIGNATURE-----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=l7Mo
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux
Pull more io_uring updates from Jens Axboe:
"Nothing major in here, just two different parts:
- A small series from Breno that enables passing the full SQE down
for ->uring_cmd().
This is a prerequisite for enabling full network socket operations.
Queued up a bit late because of some stylistic concerns that got
resolved, would be nice to have this in 6.4-rc1 so the dependent
work will be easier to handle for 6.5.
- Fix for the huge page coalescing, which was a regression introduced
in the 6.3 kernel release (Tobias)"
* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
io_uring: Remove unnecessary BUILD_BUG_ON
io_uring: Pass whole sqe to commands
io_uring: Create a helper to return the SQE size
io_uring/rsrc: check for nonconsecutive pages
Should of_mdiobus_register() fail, a previous usb_get_dev() call should be
undone as in the .disconnect function.
Fixes: 04e37d92fb ("net: phy: add marvell usb to mdio controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a980755beb.
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit 51924ae69e.
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2d55c16c0c ("dmapool: create/destroy cleanup").
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZFaTPAAKCRDdBJ7gKXxA
ji1zAP4s/mWPQOJkoTR8cn9wRdGUB4FKgDiJwwYeOdcHRuylvwEAlgOD8qlizXYu
z4tGx6J8p3X+IdEApqH6Up56wjW+Wgk=
=X19M
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-05-06-10-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull dmapool updates - again - from Andrew Morton:
"Reinstate the dmapool changes which were accidentally removed by a
mishap on the last commit in the previous attempt at the series"
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup").
[ The whole old series: def8574308ed..2d55c16c0c54 results in an empty
diff because that last commit ended up being just a revert of all that
came everything before it. - Linus ]
* tag 'mm-stable-2023-05-06-10-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
dmapool: link blocks across pages
dmapool: don't memset on free twice
dmapool: simplify freeing
dmapool: consolidate page initialization
dmapool: rearrange page alloc failure handling
dmapool: move debug code to own functions
dmapool: speedup DMAPOOL_DEBUG with init_on_alloc
dmapool: cleanup integer types
dmapool: use sysfs_emit() instead of scnprintf()
dmapool: remove checks for dev == NULL
changes.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZFaSnAAKCRDdBJ7gKXxA
jskTAPwIkL6xVMIEdtWfQNIy751o0onzfOQAIWgM3dSL83cMJQEA5OXxXt4LjrJw
4q0zf4GLYXjMjhnfYr8zXF39y05iyQA=
=nIhV
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-05-06-10-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"Five hotfixes.
Three are cc:stable, two pertain to merge window changes"
* tag 'mm-hotfixes-stable-2023-05-06-10-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
afs: fix the afs_dir_get_folio return value
nilfs2: do not write dirty data after degenerating to read-only
mm: do not reclaim private data from pinned page
nilfs2: fix infinite loop in nilfs_mdt_get_block()
mm/mmap/vma_merge: always check invariants
The allocated dmapool pages are never freed for the lifetime of the pool.
There is no need for the two level list+stack lookup for finding a free
block since nothing is ever removed from the list. Just use a simple
stack, reducing time complexity to constant.
The implementation inserts the stack linking elements and the dma handle
of the block within itself when freed. This means the smallest possible
dmapool block is increased to at most 16 bytes to accommodate these
fields, but there are no exisiting users requesting a dma pool smaller
than that anyway.
Removing the list has a significant change in performance. Using the
kernel's micro-benchmarking self test:
Before:
# modprobe dmapool_test
dmapool test: size:16 blocks:8192 time:57282
dmapool test: size:64 blocks:8192 time:172562
dmapool test: size:256 blocks:8192 time:789247
dmapool test: size:1024 blocks:2048 time:371823
dmapool test: size:4096 blocks:1024 time:362237
After:
# modprobe dmapool_test
dmapool test: size:16 blocks:8192 time:24997
dmapool test: size:64 blocks:8192 time:26584
dmapool test: size:256 blocks:8192 time:33542
dmapool test: size:1024 blocks:2048 time:9022
dmapool test: size:4096 blocks:1024 time:6045
The module test allocates quite a few blocks that may not accurately
represent how these pools are used in real life. For a more marco level
benchmark, running fio high-depth + high-batched on nvme, this patch shows
submission and completion latency reduced by ~100usec each, 1% IOPs
improvement, and perf record's time spent in dma_pool_alloc/free were
reduced by half.
[kbusch@kernel.org: push new blocks in ascending order]
Link: https://lkml.kernel.org/r/20230221165400.1595247-1-kbusch@meta.com
Link: https://lkml.kernel.org/r/20230126215125.4069751-12-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If debug is enabled, dmapool will poison the range, so no need to clear it
to 0 immediately before writing over it.
Link: https://lkml.kernel.org/r/20230126215125.4069751-11-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The actions for busy and not busy are mostly the same, so combine these
and remove the unnecessary function. Also, the pool is about to be freed
so there's no need to poison the page data since we only check for poison
on alloc, which can't be done on a freed pool.
Link: https://lkml.kernel.org/r/20230126215125.4069751-10-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Various fields of the dma pool are set in different places. Move it all
to one function.
Link: https://lkml.kernel.org/r/20230126215125.4069751-9-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Handle the error in a condition so the good path can be in the normal
flow.
Link: https://lkml.kernel.org/r/20230126215125.4069751-8-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Clean up the normal path by moving the debug code outside it.
Link: https://lkml.kernel.org/r/20230126215125.4069751-7-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Avoid double-memset of the same allocated memory in dma_pool_alloc() when
both DMAPOOL_DEBUG is enabled and init_on_alloc=1.
Link: https://lkml.kernel.org/r/20230126215125.4069751-6-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
To represent the size of a single allocation, dmapool currently uses
'unsigned int' in some places and 'size_t' in other places. Standardize
on 'unsigned int' to reduce overhead, but use 'size_t' when counting all
the blocks in the entire pool.
Link: https://lkml.kernel.org/r/20230126215125.4069751-5-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use sysfs_emit instead of scnprintf, snprintf or sprintf.
Link: https://lkml.kernel.org/r/20230126215125.4069751-4-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
dmapool originally tried to support pools without a device because
dma_alloc_coherent() supports allocations without a device. But nobody
ended up using dma pools without a device, and trying to do so will result
in an oops. So remove the checks for pool->dev == NULL since they are
unneeded bloat.
[kbusch@kernel.org: add check for null dev on create]
Link: https://lkml.kernel.org/r/20230126215125.4069751-3-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix another case of an incorrect check for the returned 'folio' value
from __filemap_get_folio().
The failure case used to return NULL, but was changed by commit
66dabbb65d ("mm: return an ERR_PTR from __filemap_get_folio").
But in the meantime, commit ec108d3cc7 ("NFS: Convert readdir page
array functions to use a folio") added a new user of that function.
And my merge of the two did not fix this up correctly.
The ext4 merge had the same issue, but that one had been caught in
linux-next and got properly fixed while merging.
Fixes: 0127f25b5d ("Merge tag 'nfs-for-6.4-1' of git://git.linux-nfs.org/projects/anna/linux-nfs")
Cc: Anna Schumaker <anna@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep returning NULL on failure instead of letting an ERR_PTR escape to
callers that don't expect it.
Link: https://lkml.kernel.org/r/20230503154526.1223095-2-hch@lst.de
Fixes: 66dabbb65d ("mm: return an ERR_PTR from __filemap_get_folio")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
According to syzbot's report, mark_buffer_dirty() called from
nilfs_segctor_do_construct() outputs a warning with some patterns after
nilfs2 detects metadata corruption and degrades to read-only mode.
After such read-only degeneration, page cache data may be cleared through
nilfs_clear_dirty_page() which may also clear the uptodate flag for their
buffer heads. However, even after the degeneration, log writes are still
performed by unmount processing etc., which causes mark_buffer_dirty() to
be called for buffer heads without the "uptodate" flag and causes the
warning.
Since any writes should not be done to a read-only file system in the
first place, this fixes the warning in mark_buffer_dirty() by letting
nilfs_segctor_do_construct() abort early if in read-only mode.
This also changes the retry check of nilfs_segctor_write_out() to avoid
unnecessary log write retries if it detects -EROFS that
nilfs_segctor_do_construct() returned.
Link: https://lkml.kernel.org/r/20230427011526.13457-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+2af3bc9585be7f23f290@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=2af3bc9585be7f23f290
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Steve French