This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6 ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, this driver (or the hardware) does not support character
length settings. It's apparently running in 8-bit mode, but it makes
userspace believe it's in 5-bit mode. That makes tcsetattr with CS8
incorrectly fail, breaking e.g. getty from busybox, thus the login shell
on ttyMVx.
Fix by hard-wiring CS8 into c_cflag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Revert commit ecb988a3b7: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
PSW 80000000 INST 00000000 HALT
//
What is displayed is some variation of:
T 00000000 HAL//
Reverting this commit via this patch fixes my problem.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep wake-up refactoring that I introduced in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")
This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier HID for UART DW 8250 on Broadcom SoCs
to match the HID passed through ACPI tables to enable
UART controller.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Tested-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of Common Clock Framework for Uartlite driver.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct uartlite_data, to store the private data of the Uartlite
driver.
Signed-off-by: Tanvi Desai <tanvi.desai@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SCIF versions mux error and break interrupts together and then provide
a separate interrupt ID for just TEI/DRI.
Allow all 6 types of interrupts to be specified via platform data (or DT)
and for any signals that are muxed together (have the same interrupt
number) simply register one handler.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no more need for SCIx_RZ_SCIFA_REGTYPE now that
SCIx_SH4_SCIF_REGTYPE can provide the same register/address definitions.
Also, R7S9210 no longer needs a special compatible since the standard
"renesas,scif" will work just fine.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with SCIx_SH4_SCIF_REGTYPE have no space between registers.
Use the register area size to determine the spacing between register.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk_ratelimited(KERN_INFO ) by pr_info_ratelimited().
It seems last printk() call in 8250_port.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No later code uses the assigned value, so it can be dropped.
Reported-by: Simon Horman <horms@verge.net.au>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe all memebers in struct exar8250_board, otherwise we get a warning:
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'has_slave' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'setup' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'exit' not described in 'exar8250_board'
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar UARTs by default supports only up to 8 channels,
all above go as extension. Thus, there is no need to have
an additional property to distinguish them from first ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/N1 UART is based on the Synopsys DW UART, but has additional
registers for DMA. This patch does not address the changes required for DMA
support, it simply adds the compatible string.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sci_request_irq() checks port->irqstr[j] for a NULL pointer, to decide
if a fallback interrupt name string should be allocated or not.
While this string is freed during port shutdown, the pointer is not
zeroed. Hence on a subsequent startup of the port, it will still be
pointing to the freed memory, leading to e.g.
WARNING: CPU: 0 PID: 404 at fs/proc/generic.c:388 __proc_create+0xbc/0x260
name len 0
or to a crash (the latter is more likely with CONFIG_DEBUG_SLAB=y, due
to the poisoning of freed memory).
Instead of zeroeing the pointer at multiple places, preinitialize
port->irqstr[j] to zero to fix this.
Fixes: 8b0bbd9562 ("serial: sh-sci: Add support for R7S9210")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for flow control functionality in the GENI serial driver
and also support for non-console higher baud rate(upto 4Mbps) usecases.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Mohammed Khajapasha <mkhaja@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't dispose IRQ mapping before it has been created.
Fixes: aa9594740 ("serial: 8250_of: Add IO space support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for a "RZ_SCIFA" which is different than a traditional
SCIFA. It looks like a normal SCIF with FIFO data, but with a
compressed address space. Also, the break out of interrupts
are different then traditinal SCIF: ERI/BRI, RXI, TXI, TEI, DRI.
The R7S9210 (RZ/A2) contains this type of SCIF.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ch is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'ch' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add these two hooks so that they can be overridden with driver specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several extended (in comparison to the traditional 16550)
registers are present in Synopsys DesignWare UART. All of them
are 32-bit ones.
Introduce helpers to simplify access to them and convert existing users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align serial8250_get_divisor() with serial8250_set_divisor() to accept
uart_port pointer as the first parameter. No functionality changes.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit b36f09c3c4 ("dmaengine: Add transfer termination
synchronization support"), dmaengine_terminate_all() is deprecated.
Replace calls to dmaengine_terminate_all() in DMA release code by calls
to dmaengine_terminate_sync(), as the latter waits until all running
completion callbacks have finished.
Replace calls to dmaengine_terminate_all() in DMA failure paths by calls
to dmaengine_terminate_async(), as these are usually done in atomic
context.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit DMA workqueue is never stopped, hence the work function may
be called after the port has been shut down.
Fix this race condition by cancelling queued work, if any, before DMA
release. Don't initialize the work if DMA initialization failed, as it
won't be used anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the sh-sci driver detects an issue with DMA during operation, it
falls backs to PIO, and releases all DMA resources.
As releasing DMA resources immediately has no advantages, but
complicates the code, and is susceptible to races, it is better to
postpone this to port shutdown.
This allows to remove the locking from sci_rx_dma_release() and
sci_tx_dma_release(), but requires keeping a copy of the DMA channel
pointers for release during port shutdown.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX FIFO timer may be armed when the port is shut down, hence the
timer function may still be called afterwards.
Fix this race condition by deleting the timer during port shutdown.
Fixes: 039403765e ("serial: sh-sci: SCIFA/B RX FIFO software timeout")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit
7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.
So, remove the entries from blacklist in order to get cards enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This writel writes the exact same value as the previous writel and is
thus unnecessary. It accidentally became unnecessary in e3538c37ee
("tty: xuartps: Beautify read-modify writes"), but the new behaviour is
now expected.
Link: https://www.spinics.net/lists/linux-serial/msg23168.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After sending data to the uart, the driver was waiting until the TX
FIFO was empty (for every single char written). After that, TX was
disabled by writing the original TX state to the status register. At
that time however, the state machine could still be shifting
characters. Not waiting can result in strange hardware states,
especially when coupled with calls to cdns_uart_set_termios, whose
symptom generally is garbage characters being received from uart or a
hang.
According to UG585, the TACTIVE bit of the channel status register
indicates the shifter operation and we should be waiting for that bit
to clear.
Sending characters does not require the TX FIFO to be empty, but merely
to not be full. So cdns_uart_console_putchar is updated accordingly.
During tests with an instrumented kernel and an oscilloscope, we could
determine that the chance of a race is reduced by this patch. It is not
removed entirely. On the oscilloscope, one can see that disabling the
transmitter early can result in the transmission hanging in the middle
of a character for a tiny duration. This hiccup is enough to
desynchronize with a remote device for a sequence of characters until a
data bit doesn't match the start or stop bits anymore.
Link: https://www.spinics.net/lists/linux-serial/msg23156.html
Link: https://www.spinics.net/lists/linux-serial/msg26139.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit mask changes in commit 6e14f7c1f2 ("tty: xuartps: Improve
startup function") doesn't do what the commit message advertises. The
original behaviour was clearing the RX_DIS bit, but due to missing ~,
that bit is now the only bit kept.
Currently, the regression is harmless, because the previous write to the
control register sets it to TXRST | RXRST. Thus the RX_DIS bit is
previously cleared. The *RST bits are cleared by the hardware, so this
commit does not currently change behaviour, but makes future changes
less risky.
Link: https://www.spinics.net/lists/linux-serial/msg23157.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Fixes: 6e14f7c1f2 ("tty: xuartps: Improve startup function")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_loop_config.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM654 uses a UART controller that is compatible (partially) with
existing 8250 UART, however, has a few differences with respect to DMA
support and control paths. Introduce a base definition that allows us
to build up the differences in follow on patches.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the non-board-specific part of the RS485 initialization from
iot2040_rs485_config function to a new generic function used also for
other boards.
This allows using TIOCGRS485 and TIOCSRS485 on boards (such as mPCIe
serial IO modules) which are hard-wired to RS485 or have jumpers for
their configurations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>