Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DT based platforms when current-speed property is present baudrate
is setup. Also port->uartclk is initialized to bogus BASE_BAUD * 16
value. Drivers like uartps/ns16550 contain logic when baudrate and
uartclk is used for baudrate calculation.
The patch is reading optional clock-frequency property to replace bogus
BASE_BAUD * 16 calculation to have proper baudrate calculation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling rountines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stacktrace by performing echo 1 > /dev/ttyS2 on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.
With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled > /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup
Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.
Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.
The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSCIF has facilities that allow moving the RX sampling point by between
-8 and 7 sampling cycles (one sampling cycles equals 1/15 of a bit
by default) to improve the error margin in case of slightly mismatched
bit rates between sender and receiver.
This patch tries to determine if shifting the sampling point can improve
the error margin and will enable it if so.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DT platforms, the sh-sci driver requires the presence of "serialN"
aliases in DT, from which instance IDs are derived. If a DT alias is
missing, the drivers fails to probe the corresponding serial port.
This becomes cumbersome when considering DT overlays, as currently
there is no upstream support for dynamically updating the /aliases node
in DT. Furthermore, even in the presence of such support, hardcoded
instance IDs in independent overlays are prone to conflicts.
Hence add support for dynamic instance IDs, to be used in the absence of
a DT alias. This makes serial ports behave similar to I2C and SPI
buses, which already support dynamic instances.
Ports in use are tracked using a simple bitmask of type unsigned long,
which is sufficient to handle all current hardware (max. 18 ports).
The maximum number of serial ports is still fixed, and configurable
through Kconfig. Range validation is done through both Kconfig and a
compile-time check.
Due to the fixed maximum number of serial ports, dynamic and static
instances share the same ID space. Static instances added later are
rejected when conflicting with dynamic instances registered earlier.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 99492c39f3 ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol. This
fix was based on commit 07fca0e57f ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.
However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format. In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array. If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".
To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
3d56e331b6 ("tracing: Replace syscall_meta_data struct array with pointer array")
6549864629 ("tracepoints: Fix section alignment using pointer array")
e4a9ea5ee7 ("tracing: Replace trace_event struct array with pointer array")
Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.
Fixes: 99492c39f3 ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To reset the UART the SRST needs be cleared (low active). According
to the documentation the bit will remain active for 4 module clocks
until it is cleared (set to 1).
Hence the real register need to be read in case the cached register
indicates that the SRST bit is zero.
This bug lead to wrong baudrate because the baud rate register got
restored before reset completed in imx_flush_buffer.
Fixes: 3a0ab62f43 ("serial: imx: implement shadow registers for UCRx and UFCR")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using half-duplex mode (which disables receiver during txing)
the RTS signal cannot be driven low during transmission when using
i.MX UART RTS/CTS control. This seems to be a limitation of the
i.MX UART IP: The RTS (CTS_B) signal is controlled by the receiver.
When the receiver is disabled, the signal stays in UART logic idle
state which is high...
If SER_RS485_RTS_ON_SEND is used, RTS needs to be high active during
transmission. Since this is the default state of the RTS (CTS_B)
signal when the receiver is off, half-duplex mode in this
configuration works fine.
However, a low-active RTS signal (flag SER_RS485_RTS_ON_SEND not set)
cannot be generated when the receiver is turned off.
Print an error if the user selects this unsupported configuration
(both SER_RS485_RTS_ON_SEND and SER_RS485_RX_DURING_TX unset) and
configure the closest working configuration (set the
SER_RS485_RX_DURING_TX flag).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add suspend and resume hooks to save/restore the registers content
during S2RAM operation.
Also save/restore the oversampling rate register (OSAMP) as earlier
stages already tuned that register to get a precise UART clock.
Suggested-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 68a0db1d7d reworked the baud rate selection, but also added
a (not so) subtle change in the way the local flags (c_lflag in the
termios structure) are handled, forcing the new flags to always be the
same as the old ones.
The reason for that particular change is both obscure and undocumented.
It also completely breaks userspace. Something as trivial as getty is
unusable:
<example>
Debian GNU/Linux 9 sy-borg ttyMV0
sy-borg login: root
root
[timeout]
Debian GNU/Linux 9 sy-borg ttyMV0
</example>
which is quite obvious in retrospect: getty cannot get in control of
the echo mode, is stuck in canonical mode, and times out without ever
seeing anything valid. It also begs the question of how this change was
ever tested.
The fix is pretty obvious: stop messing with c_lflag, and the world
will be a happier place.
Cc: stable@vger.kernel.org # 4.15+
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, tx stops working after resume. By adding
these calls, everything seems to work fine.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSn+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynb6wCdEf5dAUrSB37ptZY78n4kc6nI6NAAniDO+rjL
ppZZp7QTIB/bnPfW8cOH
=+tfY
-----END PGP SIGNATURE-----
Merge tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The tile architecture is getting removed, and this driver is
useless without it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The m32r architecture is getting removed, so we don't need this
any more.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The blackfin architecture is getting removed, so both the bfin_uart
and bfin_sport_uart can be removed as well.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cris architecture is getting removed, so we don't need the
uart driver any more.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The buf_overrun count is only every written, and not exposed to
userspace anywhere. This means that dropped characters due to flip
buffer overruns are never visible to userspace.
The /proc/tty/driver/serial file exports a bunch of metrics (including
hardware overruns) already, so add the buf_overrun (as "bo:") to this
file.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes missing characters on kernel console at low baud rates (i.e.9600).
The driver should poll TX_RDY or TX_FIFO_EMP instead of TX_EMP to ensure
that the transmitter holding register (THR) is ready to receive a new byte.
TX_EMP tells us when it is possible to send a break sequence via
SND_BRK_SEQ. While this also indicates that both the THR and the TSR are
empty, it does not guarantee that a new byte can be written just yet.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gabriel Matni <gabriel.matni@exfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function platform_get_resource() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports GENI based UART Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including UART. This driver support console
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Doug Anderson <dianders@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.
Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since dtc v1.4.6-9-gaadd0b65c987, aliases property name
must include only lowercase and '-'.
After having updated all STi boards serial aliases from "ttyASN"
to "serialN", st-asc driver need to be updated accordingly as tty
aliases id is retrieved using of_alias_get_id().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of Alphascale ASM9260 probe() enables s->clk and s->clk_ahb
via mxs_get_clks(), but there is no disable of the clocks.
The patch adds it to error paths and to mxs_auart_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 254da0d753 ("serial: mxs-auart: add Alphascale ASM9260 support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Special settings for APMC0D08 are applied when device is present
in the system. To check its presence we may use acpi_dev_present()
instead of current open coded variant.
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a fixed prefix helps at several places. It ensures that another
driver doesn't use the same function name which confuses the linker and
tools like ctags. It simplifies working with function tracing and
dynamic printk() support which can filter on function names. And last
but not least it helps the human source code reader to understand if a
given function belongs to a driver or a more general part of the kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core might call the .start_tx callback without any data being
available to send. In this case return early instead of going through
all the setup needed for sending which might include disabling RX in
RS485 half-duplex mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RS485 half duplex the Transmitter Complete irq is needed to
determine the moment when the transmitter can be disabled. When using
DMA this irq must only be enabled when DMA has completed to transfer all
data. Otherwise the CPU might busily trigger this irq which is not
properly handled and so the also pending irq for the DMA transfer cannot
trigger.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to increase the RX waterlevel which allows to delay the RRDY
irq. The desired effect is that less irqs are needed to handle
characters and so reduce irq count of the system.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that UCR1.RXDMAEN and UCR1.ATDMAEN (for the DMA case) and
UCR1.RRDYEN (for the PIO case) are off iff UCR1.RXEN is disabled. This
ensures that the fifo isn't read with RX disabled which results in an
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is used in DMA mode, .stop_rx() does nothing if the port
isn't suspended. This is wrong as .stop_rx() should stop receiving
characters unconditionally. When the port is about to be closed the DMA
channel is stopped in .shutdown(), so this isn't necessary to be in
.stop_rx() here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aging timer fires if there are characters in the RX fifo but the
water level isn't reached yet. Make sure that the waterlevel is
configured before the aging timer is enabled to trigger a DMA request
(UCR1_ATDMAEN).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial/imx driver is full of inconsistently named and typed
variables that hold different register values.
Consistently use u32 as type (matching what readl and writel use) and
name the variables after the register whose value they are holding.
This makes it easier to notice when UCR2_RTSEN is written to UCR1.
The only difference introduced by this commit in the compiled driver is
that twice the second argument to warn_slowpath_null() changed because the
two WARN_ON in dma_rx_callback() pass __LINE__ to warn_slowpath_null().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original code looks as follows:
if (sport->dma_is_enabled) {
... make sure TX DMA is running, i.e. .dma_is_txing = 1
}
if (sport->dma_is_txing)
return;
As .dma_is_txing can only be true if .dma_is_enabled is, the return can
go at the end of the first if body without an additional check.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither .dma_is_txing nor .dma_is_rxing can evaluate to true if
.dma_is_enabled evaluates to false:
The only function that sets .dma_is_txing to a non-zero value is
imx_dma_tx() which is only called if .dma_is_enabled is true. Same for
.dma_is_rxing and start_rx_dma(). And before .dma_is_enabled is set to 0
when imx_shutdown calls imx_disable_dma(), .dma_is_rxing and
.dma_is_txing are reset to zero before, too.
For this reason
sport->dma_is_enabled && sport->dma_is_rxing
has the same value as
sport->dma_is_rxing
which allows to simplify three if conditions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reduces the amount of read accesses to the register space by
shadowing the values for five registers that only change on writing
them. There is a single bit in UCR2 that might change without being
written to it, this is handled accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares implementing shadow copies for the control registers and
additionally provides a good place to hook in debug code to trace
register usage.
Most of this patch was done using pattern substitution:
perl -p -i -e '
s/\breadl(?:_relaxed)?\((?:sport->port\.|port->)membase \+/imx_uart_readl(sport,/;
s/\bwritel(?:_relaxed)?\(([^,]*), (sport->port\.|port->)membase \+/imx_uart_writel(sport, $1,/;
' drivers/tty/serial/imx.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consistently indicate being called with irqs off and the port lock taken
for all functions that this applies to.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the reference manual for the i.MX1 (I have MC9328MX1RM/D Rev 5 from
2004) uses TDMAEN and RDMAEN for these. All reference manuals for the
newer chips use TXDMAEN and RXDMAEN. Update to the newer name with the
assumption that most imx users don't use an imx1 any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e926349 ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sirf_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: a6ffe8966a ("serial: sirf: use dynamic method allocate uart structure")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sci_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a
legitimate DTB.
Fixes: 97ed9790c5 ("serial: sh-sci: Remove unused platform data capabilities field")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64f ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_pxa_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 699c20f3e6 ("serial: pxa: add OF support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4c ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fc ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after
imx_shudown() completes, .dma_is_enabled is zero. For this reason
.dma_is_enabled is also zero when imx_startup() is called. So the check
for this variable being zero can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .dma_is_inited member is only set to a value != 0 when the port's
startup function calls imx_uart_dma_init(). On shutdown of the port
imx_uart_dma_exit is called which sets the value back to 0. So
.dma_is_inited is always 0 when imx_startup() is called (assuming
.startup() and .shutdown() are correctly balanced) and the check for
!sport->dma_is_inited can go away.
This allows to replace .dma_is_inited by a variable local to
imx_startup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling an irq that isn't enabled can have some undesired side effects.
Some of these are mentioned in the newly introduced code comment. Some
of the irq sources already had their handling right, some don't. Handle
them all in the same consistent way.
The change for USR1_RRDY and USR1_AGTIM drops the check for
dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always
off if dma is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the variable holding the value of register USR1 is called usr1
instead of sts which is more straight forward. The same is also done for
sts2 which is called usr2 now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check sts & USR1_DTRD was just evaluated to true two lines above.
So this change doesn't have any effect on the semantic of the driver.
Fixes: 27e1650105 ("serial: imx: implement DSR irq handling for DTE mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only one of the two is really required, not both:
* have_rtscts or
* have_rtsgpio
In imx_rs485_config() this is done correctly, so RS485 is working,
just the error message is false.
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: b8f3bff057 ("serial: imx: Support common rs485 binding for RTS polarity"
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the TTY buffers fill up to the configured maximum, a system lockup
occurs:
[ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[ 598.838755] Task dump for CPU 0:
[ 598.841977] swapper/0 R running task 0 0 0 0x00000022
[ 598.849023] Call trace:
[ 598.851476] __switch_to+0x98/0xb0
[ 598.854870] (null)
This can be prevented by doing a dummy read of the RX data register.
This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will get the wrong virtual address because port->mapbase is not added
the correct reg-offset yet. We have to update it before earlycon_map()
is called
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org
Fixes: 088da2a176 ("of: earlycon: Initialize port fields from DT properties")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a followup on 44117a1d17 ("serial: core: mark port as
initialized after successful IRQ change").
Nikola has been using autoconfig via setserial and reported a crash
similar to what I fixed in the earlier mentioned commit. Here I do the
same fixup for the autoconfig. I wasn't sure that this is the right
approach. Nikola confirmed that it fixes his crash.
Fixes: b3b5764618 ("tty: serial_core: convert uart_open to use tty_port_open")
Link: http://lkml.kernel.org/r/20180131072000.GD1853@localhost.localdomain
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not fail on multiport cards in serial_pci_is_class_communication().
It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.
Moreover it allows users to reenumerate port-by-port from user space.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit pattern STAT_FRM_ERR is being bit-wise or'd twice; remove the
redundant 2nd STAT_FRM_ERR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows me to login after sending a break when service
serial-getty@ttymxc0.service is running
The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors
fixes this by allowing the higher layers to see a break.
Also, call uart_handle_break to handle possible
"secure attention key."
FYI: Martin said the ROM sdma firmware works with this patch,
but external sdma firmware still does not send breaks on a
i.mx6UL
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Martin Hicks <mort@bork.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An issue has been observed on the Marvell Armada 38x serial port.
Writes to UART_LCR can result in characters that are currently held in the
TX FIFO being lost rather than sent, even if the userspace process has
attempted to flush them.
This is most visible when using the "resize" command (tested on Busybox),
where we have observed the escape code for restoring cursor position
becoming mangled.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High latencies of classic timers cause performance issues for high-
speed serial transmissions. This patch transforms rx_timer into an
hrtimer to reduce the minimum latency.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.
Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some debugging tools (/sys/kernel/debug/gpio, `lsgpio`) use the
gpio_chip's label for displaying an additional context. Right now, the
information duplicates stuff which is already available from the
parent's device. This is how e.g. `lsgpio`'s output looks like:
GPIO chip: gpiochip2, "spi1.2", 16 GPIO lines
Comparing the output of other GPIO expanders that I have available:
gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17, can sleep:
gpiochip5: GPIOs 448-463, parent: i2c/0-0020, pca9555, can sleep:
gpiochip2: GPIOs 496-511, parent: spi/spi1.2, spi1.2, can sleep:
This patch ensures that the type of the real HW device is shown instead
of duplicating the SPI path:
gpiochip2: GPIOs 496-511, parent: spi/spi1.2, MAX14830, can sleep:
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART can be operated without an irq. In this case a timer is setup
that regularily calls altera_uart_interrupt(). The receiving part
depends on pp->imr having the bit ALTERA_UART_STATUS_RRDY_MSK set,
otherwise altera_uart_rx_chars() is never called. So ensure that the bit
gets set (disguised as ALTERA_UART_CONTROL_RRDY_MSK) by not returning
early from altera_uart_startup() if port->irq is 0.
This doesn't affect the hardware as the ALTERA_UART_CONTROL_RRDY_MSK bit
isn't actually written to the control register.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the irq line of an altera UART device isn't used to report interrupts
for this device the driver better ensures that this device doesn't pull
this line to active state and so disturb the whatever might be connected
to this line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d896d ("serial: altera_uart:
add earlycon support").
Fixes: 2780ad42f5 ("tty: serial: altera_uart: Use port->regshift to store bus shift")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Update the ACPICA kernel code to upstream revision 20180105 including:
* Assorted fixes (Jung-uk Kim).
* Support for X32 ABI compilation (Anuj Mittal).
* Update of ACPICA copyrights to 2018 (Bob Moore).
- Prepare for future modifications to avoid executing the _STA control
method too early (Hans de Goede).
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam).
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang).
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530
(Kai Heng Feng).
- Address static checker warnings in the CPPC code (Gustavo Silva).
- Avoid printing a raw pointer to the kernel log in the smart
battery driver (Greg Kroah-Hartman).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rVdp
-----END PGP SIGNATURE-----
Merge tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision 20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
SPCR is currently only enabled or ARM64 and x86 can use SPCR to setup
an early console.
General fixes include updating Documentation & Kconfig (for x86),
updating comments, and changing parse_spcr() to acpi_parse_spcr(),
and earlycon_init_is_deferred to earlycon_acpi_spcr_enable to be
more descriptive.
On x86, many systems have a valid SPCR table but the table version is
not 2 so the table version check must be a warning.
On ARM64 when the kernel parameter earlycon is used both the early console
and console are enabled. On x86, only the earlycon should be enabled by
by default. Modify acpi_parse_spcr() to allow options for initializing
the early console and console separately.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.
I see this change providing the following benefits:
1. If more than one port is active, eliminates the redundant bus
cycles for reading INT0 on every interrupt.
2. This note associated with hooking in the per-channel handler in
8250_port.c is resolved:
/* Fixme: probably not the best place for this */
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before we go into suspend mode, we enable the imx uart's interrupt for
the awake bit in the UART Status Register 1. If, for some reason, the
awake bit is already set before we enter suspend mode, we get an
interrupt immediately when we enable interrupts for awake. The uart's
clk_ipg is disabled at this point (unless there's an ongoing transfer).
We end up in the interrupt handler, which usually tries to clear the
awake bit. This doesn't work with the clock disabled. Therefore, we
keep getting interrupts forever, resulting in an endless loop.
Clear the awake bit before setting the awaken bit to signal that we want
an imx interrupt when the awake bit will be set. This ensures that we're
not woken up by events that happened before we started going into
suspend mode.
Change the clock handling so that suspend prepares and enables the clock
and suspend_noirq disables it. Revert these operations in resume_noirq and
resume.
With these preparations in place, we can now modify awake and awaken in
the suspend function when the actual imx interrupt is disabled and the
required clk_ipg is active.
Update the thaw and freeze functions to use the new clock handling since
we share the suspend_noirq function between suspend and hibernate.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
setserial changes the IRQ via uart_set_info(). It invokes
uart_shutdown() which free the current used IRQ and clear
TTY_PORT_INITIALIZED. It will then update the IRQ number and invoke
uart_startup() before returning to the caller leaving
TTY_PORT_INITIALIZED cleared.
The next open will crash with
| list_add double add: new=ffffffff839fcc98, prev=ffffffff839fcc98, next=ffffffff839fcc98.
since the close from the IOCTL won't free the IRQ (and clean the list)
due to the TTY_PORT_INITIALIZED check in uart_shutdown().
There is same pattern in uart_do_autoconfig() and I *think* it also
needs to set TTY_PORT_INITIALIZED there.
Is there a reason why uart_startup() does not set the flag by itself
after the IRQ has been acquired (since it is cleared in uart_shutdown)?
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation was wrong, gpiod_get_direction() returns 0/1 instead
of the GPIOF_* flags. The docs were fixed with commit 94fc73094a
("gpio: correct docs about return value of gpiod_get_direction"). Now,
fix this user (until a better, system-wide solution is in place). This
also means we can drop the deprecated use of 'linux/gpio.h'. Yay!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit
de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
obviously tries to cure symptoms, and not a root cause.
The root cause is the non-flexible rate calculation inside the
corresponding clock driver. What we need is to provide maximum UART
divisor value to the clock driver to allow it do the job transparently
to the caller.
Since from the initial commit message I have got no clue which clock
driver actually needs to be amended, I leave this exercise to the people
who know better the case.
Moreover, it seems [1] the fix introduced a regression. And possible
even one more [2].
Taking above, revert the commit de9e33bdfa for now.
[1]: https://www.spinics.net/lists/linux-serial/msg28872.html
[2]: https://github.com/Dunedan/mbp-2016-linux/issues/29#issuecomment-357583782
Fixes: de9e33bdfa ("serial: 8250_dw: Improve clock rate setting")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Ed Blake <ed.blake@sondrel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The push-pull vs. open-drain are the only supported output modes. The
inputs are always unconditionally equipped with weak pull-downs. That's
the only mode, so there's probably no point in exporting that. I wonder
if it's worthwhile to provide a custom dbg_show method to indicate the
current status of the outputs, though.
This patch and [1] for i2c-gpio together make it possible to bit-bang an
I2C bus over GPIOs of an UART which is connected via SPI :). Yes, this
is crazy, but it's fast enough (while on a 26Mhz SPI HW bus with a
dual-core 1.6GHz CPU) to drive an I2C bus at 200kHz, according to my
scope.
[1] https://patchwork.ozlabs.org/patch/852591/
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the devicetree, it is possible to specify the baudrate, parity,
bits, flow of the early console, by passing a configuration string like
this:
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:57600n8";
};
This, for instance, will configure the early console for a baudrate of
57600 bps, no parity, and 8 bits per baud.
This patches implements parsing of this configuration string in the
8250_ingenic driver, which previously just ignored it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The JZ4770 SoC's UART is no different from the other JZ SoCs, so this
commit simply adds the ingenic,jz4770-uart compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointed string is never modified from within uart_parse_options, so
it should be marked as const in the function prototype.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error pointer from devm_reset_control_get_optional_shared() is
not propagated.
One of the most common problem scenarios is it returns -EPROBE_DEFER
when the reset controller has not probed yet. In this case, the
probe of the reset consumer should be deferred.
Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS
lines, so only allow such wakeup method when the system actually has
RTS/CTS support.
Fixes: bc85734b12 ("serial: imx: allow waking up on RTSD")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the port register error
handling case instead of 0, as done elsewhere in this function.
Fixes: 39be40ce06 ("serial: 8250_uniphier: fix serial port index in private data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rs485 flag "SER_RS485_RTS_AFTER_SEND" was wrongly read from the GPIO
flags. This caused the RTS pin to be high during boot.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All calls to neo_copy_data_from_uart_to_queue() are safeguarded
against NULL dereference of its parameter, except the one that
this patch changes.
That said, let's play safe and check for NULL in this case too.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After inspection made by Markus using Coccinelle software, he
observed that we could possibly be triggering a NULL pointer
dereference in 2 functions [0].
After discussion in mailing list, it was observed in fact
we have two unnecessary checks for NULL pointer, and they
were leading to Coccinelle warn. So, instead of reworking
the code as proposed by him, we hereby remove the
unnecessary checks, and also some unneeded extra lines in
the code.
These two unnecessary NULL checks were tracked in the call
chain as never NULL, so they can be safely removed.
No functional changes are intended.
[0] https://lkml.org/lkml/2017/11/29/705
Suggested-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this patch, the code would happily trigger TX on some ports
before having a chance of reading the RX buffer from the rest of them.
When no flow control was used, this led to RX buffer overruns and
therefore lost data under certain circumstances.
I was able to reproduce this with MAX14830 (that's a quad channel one)
and a simple daisy-chain of RX and TX ports on the eval board:
- TX0 -> RX1
- TX1 -> RX2
- TX2 -> RX3
- TX3 -> RX0
I was testing this by transferring 2MB of data at 115200 baud via each
port. I used a Solidrun Clearfog Base (Armada 388) which was talking to
the UART over an SPI bus clocked at 26MHz (the chip's maximum). Without
this patch, I would always get a "Possible RX FIFO overrun" in dmesg,
and fewer-than-expected amount of bytes received over ttyMAX0. Results
on ttyMAX{1,2,3} tended to be correct all the time, even without the
previous patches in this series and with PIO SPI transfers ("indirect
mode" as the Marvell datasheet calls it), so I assume that heavy
congestion is needed in order to reproduce this.
A drawback of this patch is that the throughput gets reduced "a bit".
Previously, a 115200 baud resulted in about 11.2kBps throughput as
reported by a simple `pv`. With this patch, the throughput of four
parallel streams is roughly 7kBps each, and 9kBps for three streams.
There is no slowdown for one or two parallel streams.
Situation is worse if bytes are being read one-by-one (such as if the
userspace wants to perform parity/framing/break checking) and therefore
without the batched reads.
With just this patch and no other modifications on top of 4.14, I was
only getting roughly 3.6kBps with four parallel streams. The
single-stream performance was the same, and I was seeing about 7.2kBps
with two parallel streams. `perf top` said that a substantial amount of
time was spent in `finish_task_switch`, `_raw_spin_unlock_irqrestore`
and `__timer_delay`.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware has a 128 byte RX FIFO buffer for each independent UART.
Previously, the code was always reading that byte-by-byte via
independent SPI transactions and the associated overhead. In practice,
this led to up to eight bytes over SPI for just one byte in the UART's
RX FIFO:
- reading the global IRQ register (two bytes, one for command, the other
for data)
- reading one UART's ISR (again two bytes)
- reading the byte count (two bytes yet again)
- finally, reading one byte of the FIFO via another two-byte transaction
We cannot always use a batched read. If the TTY is set to intercept
break conditions or report framing or parity errors, then it is required
to check the Line Status Register (LSR) for each byte which is read from
the RX FIFO. The documentation does not show a way of doing that in a
single SPI transaction; registers 0x00 and 0x04 are separate.
In my testing, this is no silver bullet. I was feeding 2MB of random
data over four daisy-chaned UARTs of MAX14830, and this is the
distribution that I was getting:
- R <= 1: 7437322
- R <= 2: 162093
- R <= 4: 4093
- R <= 8: 4196
- R <= 16: 645
- R <= 32: 165
- R <= 64: 58
- R <= 128: 0
For a reference, batching the write operations works much better:
- W <= 1: 2664
- W <= 2: 1305
- W <= 4: 627
- W <= 8: 371
- W <= 16: 121
- W <= 32: 68
- W <= 64: 33
- W <= 128: 63139
That's probably because this HW/SW combination (Clearfog Base, Armada
388) is probably "good enough" to react to the chip's IRQ "fast enough"
most of the time. Still, I was getting RX overruns every now and then.
In future, I plan to improve this by letting the RX FIFO be filled a
little more (the chip has support for that and also for a "stale
timeout" to prevent additional starvation).
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit register supports batched writes. The key is simply to keep
sending additional bytes up to the FIFO size in the same SPI
transaction with the CS pin still being held low.
This duplicates the regmap infrastructure to a certain extent. There are
some provisions for multiple writes in there, but there does not appear
to be any support for those writes which are destined to the *same*
register (and also no standard for SPI bus transfers of these, anyway).
This patch does not solve every case (if the UART xmit circular buffer
wraps around, we're still doing two SPI transactions), but at least
it's not one-byte-per-transaction anymore.
This change does not touch the receive path at this time. Doing that in
the generic case appears to be impossible in the general case, because
the chips' status register contains data about the *current* byte in the
HW's Rx FIFO. We cannot read these two registers in one go,
unfortunately.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to my chip's datasheet [1], the IRQ output is an open
collector pin which is suitable for sharing with other chips. The chip
also has a register which indicates which UART performed a change and
the driver checks that register already, so we have everything what is
needed to effectively share the IRQ GPIO.
[1] https://datasheets.maximintegrated.com/en/ds/MAX14830.pdf
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Russell King, a driver should not really care about bits
such as the interrupt polarity or whether it is edge- or level-
triggered. The reasons for that include:
- an upstream IRQ controller which cannot support edge- or
level-triggered interrupts,
- board design with a built-in inverter
The interrupt type is being already specified by the Device Tree,
anyway. Other drivers (gpio/gpio-tc3589x.c for example) already work in
this way, delegating the proper IRQ line setup to the DT and not
specifying anything by hand.
Also, there's no reason to have the IRQ flags split between two places.
The SPI probing is the only entry point anyway.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compile-testing an allmodconfig kernel for a platform without
sh-sci serial ports, the SERIAL_SH_SCI_NR_UARTS symbol of type "int"
doesn't get assigned a numerical default value, but an empty string,
leading to a build failure:
.config:3814:warning: symbol value '' invalid for SERIAL_SH_SCI_NR_UARTS
...
make[3]: *** [silentoldconfig] Error 1
Fix this by explicitly providing a default value of 2, like before.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: f6731485a5 ("tty: serial: sh-sci: Hide number of ports config question")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `max310x_spi_probe` function attempted to setup the GPIO bits before
the corresponding structs for each serial port were initialized. If the
DTS file specified a GPIO hog, this led to a crash because the GPIO
stack ended up calling `max310x_gpio_direction_output` which referenced
uninitialized memory:
[<c04598c0>] (max310x_gpio_direction_output) from [<c03f5a2c>] (_gpiod_direction_output_raw+0x94/0x2d4)
[<c03f5a2c>] (_gpiod_direction_output_raw) from [<c03f991c>] (gpiod_hog+0x6c/0x154)
[<c03f991c>] (gpiod_hog) from [<c03fa2d8>] (of_gpiochip_add+0x28c/0x444)
[<c03fa2d8>] (of_gpiochip_add) from [<c03f6b2c>] (gpiochip_add_data+0x4f8/0x760)
[<c03f6b2c>] (gpiochip_add_data) from [<c03f6dd4>] (devm_gpiochip_add_data+0x40/0x7c)
[<c03f6dd4>] (devm_gpiochip_add_data) from [<c0459fec>] (max310x_spi_probe+0x530/0x894)
[<c0459fec>] (max310x_spi_probe) from [<c0503294>] (spi_drv_probe+0x7c/0xac)
[<c0503294>] (spi_drv_probe) from [<c046628c>] (driver_probe_device+0x234/0x2e8)
[<c046628c>] (driver_probe_device) from [<c0464890>] (bus_for_each_drv+0x60/0x94)
[<c0464890>] (bus_for_each_drv) from [<c0465f78>] (__device_attach+0xb0/0x114)
[<c0465f78>] (__device_attach) from [<c0465548>] (bus_probe_device+0x84/0x8c)
[<c0465548>] (bus_probe_device) from [<c0463a00>] (device_add+0x3f4/0x580)
[<c0463a00>] (device_add) from [<c0504164>] (spi_add_device+0x9c/0x134)
[<c0504164>] (spi_add_device) from [<c0504c18>] (spi_register_controller+0x484/0x910)
[<c0504c18>] (spi_register_controller) from [<c0506ee0>] (orion_spi_probe+0x2f4/0x3b4)
[<c0506ee0>] (orion_spi_probe) from [<c0467dac>] (platform_drv_probe+0x50/0xb0)
[<c0467dac>] (platform_drv_probe) from [<c046628c>] (driver_probe_device+0x234/0x2e8)
[<c046628c>] (driver_probe_device) from [<c04663f8>] (__driver_attach+0xb8/0xbc)
[<c04663f8>] (__driver_attach) from [<c04647e8>] (bus_for_each_dev+0x68/0x9c)
[<c04647e8>] (bus_for_each_dev) from [<c046574c>] (bus_add_driver+0x104/0x210)
[<c046574c>] (bus_add_driver) from [<c0466f14>] (driver_register+0x78/0xf4)
[<c0466f14>] (driver_register) from [<c0101bdc>] (do_one_initcall+0x44/0x168)
[<c0101bdc>] (do_one_initcall) from [<c0a00dc0>] (kernel_init_freeable+0x140/0x1cc)
[<c0a00dc0>] (kernel_init_freeable) from [<c078c590>] (kernel_init+0x8/0x108)
[<c078c590>] (kernel_init) from [<c0107a50>] (ret_from_fork+0x14/0x24)
This can be easily fixed by moving the corresponding code below. And
because the UARTs are already there by the time we reach this point, the
`goto` needs changing so that more stuff is freed. (I have not tested
this error path.)
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If uart_add_one_port() fails in mxs_auart_probe, the clks has
to be disabled.Two clks are previously enabled in mxs_get_clks().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed a spelling error in a comment.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is no clock rate for uartclk defined, disable the previously
enabled clock again.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 23f5b3fdd0 serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On most Renesas ARM platforms, the SCIF serial ports can be used with
DMA, so most users will want DMA support to be enabled.
On SuperH platforms, SCI(F) serial ports cannot be used with DMA yet
(see also commit 219fb0c143 ("serial: sh-sci: Remove the platform
data dma slave rx/tx channel IDs")), so users will want it disabled to
reduce kernel size.
Hence follow the above rationale to configure the default, unless
CONFIG_EXPERT is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas H8/300 and ARM platforms use DT and support earlycon, so most
users want earlycon support to be enabled.
On SuperH platforms, earlycon is not yet supported.
Hence follow the above rationale to configure the default, unless
CONFIG_EXPERT is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most users will want to use a serial console.
Hence make that the default, unless CONFIG_EXPERT is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto-configure the maximum number of serial ports based on how many can
be present on the architecture:
- 3 on H8/300,
- 10 on SuperH,
- 18 on Reneas ARM.
The default can still be overridden if CONFIG_EXPERT is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using "make kvmconfig" results in a potentially unusable linux image
on s390. The reason is that both the (default on s390) sclp consoles
as well as the 8250 console register a ttyS<x> as console. Since there
will be no 8250 on s390 let's fence 8250. This will ensure that there
is always a working sclp console.
Reported-by: Alice Frosi <alice@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoke the ->rs485_config callback on probe to adjust the initial RTS
polarity based on the UART's device properties.
This implicitly fixes a bug: If RTS control is not available, rs485
should be disabled even if it was enabled through a device property.
Log an error when that occurs.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoke the ->rs485_config callback on probe to set UARTMODEM_TXRTSPOL
appropriately based on the UART's device properties.
This implicitly sets UARTMODEM_TXRTSE if rs485 was enabled in the device
properties, so drop the identical code from lpuart_probe().
It also fixes a bug: If an unsupported rs485 property was specified
(rs485-rx-during-tx or rs485-rts-delay), the driver returns -ENOSYS
without performing any cleanup, in particular without calling
uart_remove_one_port() or clk_disable_unprepare(), thus leaking the
uart_port. But with the invocation of ->rs485_config, the unsupported
properties are now cleared in struct serial_rs485 and thus ignored.
It therefore seems sufficient to just log an error instead of bailing
out.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver invokes the uart_get_rs485_mode() helper, set the RTS
polarity to active high by default unless the newly introduced
"rs485-rts-active-low" property was specified.
imx contains a line to set the default RTS polarity to active high,
it is now superfluous and hence deleted.
omap-serial historically defaults to active low and supports an
"rs485-rts-active-high" property to inverse the polarity.
Retain that behavior for compatibility.
Cc: Mark Jackson <mpfj@newflow.co.uk>
Cc: Michał Oleszczyk <oleszczyk.m@gmail.com>
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef838a81dd ("serial: Add common rs485 device tree parsing
function") consolidated retrieval of rs485 OF properties in a common
helper function but did not #ifdef it to CONFIG_OF. The function is
therefore included on ACPI platforms as well even though it's not used.
On the other hand ACPI platforms with rs485 do exist (e.g. Siemens
IOT2040) and they may leverage _DSD to store rs485 properties. Likewise,
UART platform devices instantiated from an MFD should be able to specify
rs485 properties. In fact, the tty subsystem maintainer had asked for
a "generic" function during review of commit ef838a81dd:
https://marc.info/?l=linux-serial&m=150143441725194&w=4
Thus, instead of constraining the helper to OF platforms, make it
platform-agnostic by converting it to device_property_*() functions
and renaming it accordingly.
In imx.c, move the invocation of uart_get_rs485_mode() from
serial_imx_probe_dt() to serial_imx_probe() so that it also gets called
for non-OF devices.
In omap-serial.c, move its invocation further up within
serial_omap_probe_rs485() so that the RTS polarity can be overridden
with the driver-specific "rs485-rts-active-high" property once we
introduce a generic "rs485-rts-active-low" property.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If either uartclk or baud are 0, avoid calculating and setting a divisor
based on them since the output will almost certainly be garbage.
This also allows platforms such as the MIPS generic kernel, which has no
way to know a valid BASE_BASE for the board it is actually booted on at
compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad
divisor.
This fixes a regression caused by commit 31cb9a8575 ("earlycon:
initialise baud field of earlycon device structure"), which changed the
behavior of of_setup_earlycon such that it sets a baud rate in the
earlycon structure where previously it was left as 0. All boards
supported by the MIPS generic kernel started outputting garbage from the
boot console due to an incorrect divisor being set.
Fixes: 31cb9a8575 ("earlycon: initialise baud field of earlycon device structure")
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx_disable_rx_int is only called by imx_startup,
let's integrate it into that function. Notice UCR2_ATEN is
never set by the driver. The bit is still cleaned to make
this patch a noop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 075167ed71 ("drivers: PL011: replace UART_MIS reading with
_RIS & _IMSC") amended this driver's interrupt handler to read the
Raw Interrupt Status (RIS) and Interrupt Mask Set/Clear (IMSC) registers
instead of the Masked Interrupt Status (MIS) register. The change was
made to attain compatibility with SBSA UARTs which lack the MIS register.
However the IMSC register is cached by the driver. Using the cached
copy saves one register read per interrupt.
I've tested this change successfully on a BCM2837 (Raspberry Pi CM3).
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Phil Elwell <phil@raspberrypi.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Cc: Naresh Bhat <nbhat@cavium.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_fifo_to_tty() has two counters (max_count and fifotaken) for the
same loop. One counter should suffice. This saves one subtraction per
character read from the RX FIFO.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Phil Elwell <phil@raspberrypi.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simply fixes a typo in the preprocessor macros. No functional
changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the code there are two separate sections which each describe some of
the bits in the AML_UART_CONTROL register.
Merge these into one section to make the code easier to read.
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "clear error" bit in the AML_UART_CONTROL register is defined twice.
Remove the AML_UART_CLR_ERR definition and replace it with
AML_UART_CLEAR_ERR.
AML_UART_CLEAR_ERR was chosen to be kept since the datasheet's
description for this bit is "Clear Error" (so developer's don't have to
translate this to "CLR_ERR").
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
Devices like DCF77 receivers need the baud-rate to be as low as 50.
I have tested this on a Meson GXL device with uart_A.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thomas Rohloff <v10lator@myway.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.
It can be tested with following C code:
...
struct termios options;
tcgetattr(fd, &options);
...
options.c_cflag = CS8 | CREAD; /* baud rate 0 */
tcsetattr(fd, TCSANOW, &options);
tcflush(fd, TCIOFLUSH);
Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, only the first port supports delay before
send and delay after send.
Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).
The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.
Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ts is assigned a value that is never read, ts is therefore
redundant and can be removed. Cleans up clang warning:
drivers/tty/serial/jsm/jsm_tty.c:285:2: warning: Value stored to 'ts'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl complains:
space required before the open parenthesis '('.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes checkpatch.pl warning:
space prohibited between function name and open parenthesis '('.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes checkpatch.pl warning:
Missing a blank line after declarations.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of jsm_get_mstat was int, and the local var result
was for the return should be int, make the change.
This patch fixes the checkpatch.pl warning:
Prefer 'unsigned int' to bare use of 'unsigned'.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Codify using a named clock for the refclk of the uart. This makes it
easier if we might need to add a gating clock (like present on the
BCM6345).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@linux-mips.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/17328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Hogan <jhogan@kernel.org>
Since commit 4dec2f119e ("imx-serial: RX DMA startup latency")
the interrupt routine no longer will start rx dma.
imx_dma_rxint no longer needs to be called to try and start dma.
It won't start dma because dma_is_rxing is
already true meaning dma is already started.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4dec2f119e ("imx-serial: RX DMA startup latency")
the interrupt routine no longer will start rx dma.
So, we no longer need to enable this interrupt to start dma.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the timer converted to using the new timer_setup()/from_timer() API,
setting the .data field is redundant (and the field will be removed soon),
so drop it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During hibernation, freeze/thaw/restore dev_pm_ops are called instead of
suspend/resume. Hook up the hibernation ops. The _noirq parts are
identical, but suspend/resume are replaced with variants that do not
enable wakeup from i.MX UART. There is no need to restore register
contents in thaw_noirq.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
