Tobias Waldekranz says:
====================
net: bridge: Multiple Spanning Trees
The bridge has had per-VLAN STP support for a while now, since:
https://lore.kernel.org/netdev/20200124114022.10883-1-nikolay@cumulusnetworks.com/
The current implementation has some problems:
- The mapping from VLAN to STP state is fixed as 1:1, i.e. each VLAN
is managed independently. This is awkward from an MSTP (802.1Q-2018,
Clause 13.5) point of view, where the model is that multiple VLANs
are grouped into MST instances.
Because of the way that the standard is written, presumably, this is
also reflected in hardware implementations. It is not uncommon for a
switch to support the full 4k range of VIDs, but that the pool of
MST instances is much smaller. Some examples:
Marvell LinkStreet (mv88e6xxx): 4k VLANs, but only 64 MSTIs
Marvell Prestera: 4k VLANs, but only 128 MSTIs
Microchip SparX-5i: 4k VLANs, but only 128 MSTIs
- By default, the feature is enabled, and there is no way to disable
it. This makes it hard to add offloading in a backwards compatible
way, since any underlying switchdevs have no way to refuse the
function if the hardware does not support it
- The port-global STP state has precedence over per-VLAN states. In
MSTP, as far as I understand it, all VLANs will use the common
spanning tree (CST) by default - through traffic engineering you can
then optimize your network to group subsets of VLANs to use
different trees (MSTI). To my understanding, the way this is
typically managed in silicon is roughly:
Incoming packet:
.----.----.--------------.----.-------------
| DA | SA | 802.1Q VID=X | ET | Payload ...
'----'----'--------------'----'-------------
|
'->|\ .----------------------------.
| +--> | VID | Members | ... | MSTI |
PVID -->|/ |-----|---------|-----|------|
| 1 | 0001001 | ... | 0 |
| 2 | 0001010 | ... | 10 |
| 3 | 0001100 | ... | 10 |
'----------------------------'
|
.-----------------------------'
| .------------------------.
'->| MSTI | Fwding | Lrning |
|------|--------|--------|
| 0 | 111110 | 111110 |
| 10 | 110111 | 110111 |
'------------------------'
What this is trying to show is that the STP state (whether MSTP is
used, or ye olde STP) is always accessed via the VLAN table. If STP
is running, all MSTI pointers in that table will reference the same
index in the STP stable - if MSTP is running, some VLANs may point
to other trees (like in this example).
The fact that in the Linux bridge, the global state (think: index 0
in most hardware implementations) is supposed to override the
per-VLAN state, is very awkward to offload. In effect, this means
that when the global state changes to blocking, drivers will have to
iterate over all MSTIs in use, and alter them all to match. This
also means that you have to cache whether the hardware state is
currently tracking the global state or the per-VLAN state. In the
first case, you also have to cache the per-VLAN state so that you
can restore it if the global state transitions back to forwarding.
This series adds a new mst_enable bridge setting (as suggested by Nik)
that can only be changed when no VLANs are configured on the
bridge. Enabling this mode has the following effect:
- The port-global STP state is used to represent the CST (Common
Spanning Tree) (1/15)
- Ingress STP filtering is deferred until the frame's VLAN has been
resolved (1/15)
- The preexisting per-VLAN states can no longer be controlled directly
(1/15). They are instead placed under the MST module's control,
which is managed using a new netlink interface (described in 3/15)
- VLANs can br mapped to MSTIs in an arbitrary M:N fashion, using a
new global VLAN option (2/15)
Switchdev notifications are added so that a driver can track:
- MST enabled state
- VID to MSTI mappings
- MST port states
An offloading implementation is this provided for mv88e6xxx.
====================
Link: https://lore.kernel.org/r/20220316150857.2442916-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for MST state changes.
When a state changes to disabled/blocking/listening, make sure to fast
age any dynamic entries in the affected VLANs (those controlled by the
MSTI in question).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for VLAN MSTI migrations.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When joining a bridge where MST is enabled, we validate that the
proper offloading support is in place, otherwise we fallback to
software bridging.
When then mode is changed on a bridge in which we are members, we
refuse the change if offloading is not supported.
At the moment we only check for configurable learning, but this will
be further restricted as we support more MST related switchdev events.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers who are offloading MST states
into hardware. As an example, a driver may wish to flush the FDB for a
port when it transitions from forwarding to blocking - which means
that the previous state must be discoverable.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers that might want to refuse to join
a bridge where MST is enabled, if the hardware can't support it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_mst_get_info answers the question: "On this bridge, which VIDs are
mapped to the given MSTI?"
This is useful in switchdev drivers, which might have to fan-out
operations, relating to an MSTI, per VLAN.
An example: When a port's MST state changes from forwarding to
blocking, a driver may choose to flush the dynamic FDB entries on that
port to get faster reconvergence of the network, but this should only
be done in the VLANs that are managed by the MSTI in question.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a number of systems supporting DASH remote management.
Driver unload and system shutdown can result in the PHY suspending,
thus making DASH unusable. Improve this by handling DASH being enabled
very similar to WoL being enabled.
Tested-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/1de3b176-c09c-1654-6f00-9785f7a4f954@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-03-16
This series contains updates to gtp and ice driver.
Wojciech fixes smatch reported inconsistent indenting for gtp and ice.
Yang Yingliang fixes a couple of return value checks for GNSS to IS_PTR
instead of null.
Jacob adds support for trace events on tx timestamps.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: add trace events for tx timestamps
ice: fix return value check in ice_gnss.c
ice: Fix inconsistent indenting in ice_switch
gtp: Fix inconsistent indenting
====================
Link: https://lore.kernel.org/r/20220316204024.3201500-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in a dev_err message and the MAX_SKB_FRAGS
value does not need to be printed between parentheses. Fix this.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220316233455.54541-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with -Wformat, clang emits the following warning:
net/8021q/vlanproc.c:284:22: warning: format specifies type 'unsigned
short' but the argument has type 'int' [-Wformat]
mp->priority, ((mp->vlan_qos >> 13) & 0x7));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Link: https://lore.kernel.org/r/20220316213125.2353370-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with -Wformat, clang emits the following warning:
drivers/net/ethernet/freescale/xgmac_mdio.c:243:22: warning: format
specifies type 'unsigned char' but the argument has type 'int'
[-Wformat]
phy_id, dev_addr, regnum);
^~~~~~
./include/linux/dev_printk.h:163:47: note: expanded from macro 'dev_dbg'
dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:129:34: note: expanded from macro 'dev_printk'
_dev_printk(level, dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Link: https://lore.kernel.org/r/20220316213114.2352352-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with -Wformat, clang emits the following warnings:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6181:40: warning: format
specifies type 'unsigned short' but the argument has type 'u32'
(aka 'unsigned int') [-Wformat]
ret = scnprintf(str, *len, "%hx.%hx", num >> 16, num);
~~~ ^~~~~~~~~
%x
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6181:51: warning: format
specifies type 'unsigned short' but the argument has type 'u32'
(aka 'unsigned int') [-Wformat]
ret = scnprintf(str, *len, "%hx.%hx", num >> 16, num);
~~~ ^~~
%x
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6196:47: warning: format
specifies type 'unsigned char' but the argument has type 'u32'
(aka 'unsigned int') [-Wformat]
ret = scnprintf(str, *len, "%hhx.%hhx.%hhx", num >> 16, num >> 8, num);
~~~~ ^~~~~~~~~
%x
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6196:58: warning: format
specifies type 'unsigned char' but the argument has type 'u32'
(aka 'unsigned int') [-Wformat]
ret = scnprintf(str, *len, "%hhx.%hhx.%hhx", num >> 16, num >> 8, num);
~~~~ ^~~~~~~~
%x
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6196:68: warning: format
specifies type 'unsigned char' but the argument has type 'u32'
(aka 'unsigned int') [-Wformat]
ret = scnprintf(str, *len, "%hhx.%hhx.%hhx", num >> 16, num >> 8, num);
~~~~ ^~~
%x
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Link: https://lore.kernel.org/r/20220316213104.2351651-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with -Wformat, clang emits the following warning:
drivers/net/ethernet/freescale/enetc/enetc_mdio.c:151:22: warning:
format specifies type 'unsigned char' but the argument has type 'int'
[-Wformat]
phy_id, dev_addr, regnum);
^~~~~~
./include/linux/dev_printk.h:163:47: note: expanded from macro 'dev_dbg'
dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:129:34: note: expanded from macro 'dev_printk'
_dev_printk(level, dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220316213109.2352015-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and wireless.
Current release - regressions:
- Revert "netfilter: nat: force port remap to prevent shadowing
well-known ports", restore working conntrack on asymmetric paths
- Revert "ath10k: drop beacon and probe response which leak from
other channel", restore working AP and mesh mode on QCA9984
- eth: intel: fix hang during reboot/shutdown
Current release - new code bugs:
- netfilter: nf_tables: disable register tracking, it needs more
work to cover all corner cases
Previous releases - regressions:
- ipv6: fix skb_over_panic in __ip6_append_data when (admin-only)
extension headers get specified
- esp6: fix ESP over TCP/UDP, interpret ipv6_skip_exthdr's return
value more selectively
- bnx2x: fix driver load failure when FW not present in initrd
Previous releases - always broken:
- vsock: stop destroying unrelated sockets in nested virtualization
- packet: fix slab-out-of-bounds access in packet_recvmsg()
Misc:
- add Paolo Abeni to networking maintainers!
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=pStH
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, ipsec, and wireless.
A few last minute revert / disable and fix patches came down from our
sub-trees. We're not waiting for any fixes at this point.
Current release - regressions:
- Revert "netfilter: nat: force port remap to prevent shadowing
well-known ports", restore working conntrack on asymmetric paths
- Revert "ath10k: drop beacon and probe response which leak from
other channel", restore working AP and mesh mode on QCA9984
- eth: intel: fix hang during reboot/shutdown
Current release - new code bugs:
- netfilter: nf_tables: disable register tracking, it needs more work
to cover all corner cases
Previous releases - regressions:
- ipv6: fix skb_over_panic in __ip6_append_data when (admin-only)
extension headers get specified
- esp6: fix ESP over TCP/UDP, interpret ipv6_skip_exthdr's return
value more selectively
- bnx2x: fix driver load failure when FW not present in initrd
Previous releases - always broken:
- vsock: stop destroying unrelated sockets in nested virtualization
- packet: fix slab-out-of-bounds access in packet_recvmsg()
Misc:
- add Paolo Abeni to networking maintainers!"
* tag 'net-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (26 commits)
iavf: Fix hang during reboot/shutdown
net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower offload
net: bcmgenet: skip invalid partial checksums
bnx2x: fix built-in kernel driver load failure
net: phy: mscc: Add MODULE_FIRMWARE macros
net: dsa: Add missing of_node_put() in dsa_port_parse_of
net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
Revert "ath10k: drop beacon and probe response which leak from other channel"
hv_netvsc: Add check for kvmalloc_array
iavf: Fix double free in iavf_reset_task
ice: destroy flow director filter mutex after releasing VSIs
ice: fix NULL pointer dereference in ice_update_vsi_tx_ring_stats()
Add Paolo Abeni to networking maintainers
atm: eni: Add check for dma_map_single
net/packet: fix slab-out-of-bounds access in packet_recvmsg()
net: mdio: mscc-miim: fix duplicate debugfs entry
net: phy: marvell: Fix invalid comparison in the resume and suspend functions
esp6: fix check on ipv6_skip_exthdr's return value
net: dsa: microchip: add spi_device_id tables
netfilter: nf_tables: disable register tracking
...
Revert recent commit that caused multiple systems to misbehave due
to firmware issues.
-----BEGIN PGP SIGNATURE-----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=hOB7
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert recent commit that caused multiple systems to misbehave due to
firmware issues"
* tag 'acpi-5.17-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: scan: Do not add device IDs from _CID if _HID is not valid"
Merge misc fixes from Andrew Morton:
"Four patches.
Subsystems affected by this patch series: mm/swap, kconfig, ocfs2, and
selftests"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
selftests: vm: fix clang build error multiple output files
ocfs2: fix crash when initialize filecheck kobj fails
configs/debug: restore DEBUG_INFO=y for overriding
mm: swap: get rid of livelock in swapin readahead
When building the vm selftests using clang, some errors are seen due to
having headers in the compilation command:
clang -Wall -I ../../../../usr/include -no-pie gup_test.c ../../../../mm/gup_test.h -lrt -lpthread -o .../tools/testing/selftests/vm/gup_test
clang: error: cannot specify -o when generating multiple output files
make[1]: *** [../lib.mk:146: .../tools/testing/selftests/vm/gup_test] Error 1
Rework to add the header files to LOCAL_HDRS before including ../lib.mk,
since the dependency is evaluated in '$(OUTPUT)/%:%.c $(LOCAL_HDRS)' in
file lib.mk.
Link: https://lkml.kernel.org/r/20220304000645.1888133-1-yosryahmed@google.com
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Once s_root is set, genric_shutdown_super() will be called if
fill_super() fails. That means, we will call ocfs2_dismount_volume()
twice in such case, which can lead to kernel crash.
Fix this issue by initializing filecheck kobj before setting s_root.
Link: https://lkml.kernel.org/r/20220310081930.86305-1-joseph.qi@linux.alibaba.com
Fixes: 5f483c4abb ("ocfs2: add kobject for online file check")
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, I failed to realize that Kees' patch [1] has not been merged
into the mainline yet, and dropped DEBUG_INFO=y too eagerly from the
mainline. As the results, "make debug.config" won't be able to flip
DEBUG_INFO=n from the existing .config. This should close the gaps of a
few weeks before Kees' patch is there, and work regardless of their
merging status anyway.
Link: https://lore.kernel.org/all/20220125075126.891825-1-keescook@chromium.org/ [1]
Link: https://lkml.kernel.org/r/20220308153524.8618-1-quic_qiancai@quicinc.com
Signed-off-by: Qian Cai <quic_qiancai@quicinc.com>
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In our testing, a livelock task was found. Through sysrq printing, same
stack was found every time, as follows:
__swap_duplicate+0x58/0x1a0
swapcache_prepare+0x24/0x30
__read_swap_cache_async+0xac/0x220
read_swap_cache_async+0x58/0xa0
swapin_readahead+0x24c/0x628
do_swap_page+0x374/0x8a0
__handle_mm_fault+0x598/0xd60
handle_mm_fault+0x114/0x200
do_page_fault+0x148/0x4d0
do_translation_fault+0xb0/0xd4
do_mem_abort+0x50/0xb0
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com
Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Yang Yang <yang.yang29@zte.com.cn>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ziliang Guo <guo.ziliang@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent commit 974578017f ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes: fa164e40c5 ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix array_size.cocci warning in tools/testing/selftests/net.
Use `ARRAY_SIZE(arr)` instead of forms like `sizeof(arr)/sizeof(arr[0])`.
It has been tested with gcc (Debian 8.3.0-6) 8.3.0.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220316092858.9398-1-guozhengkui@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This code works but it has a static checker warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1687 init_dma_rx_desc_rings()
warn: always true condition '(queue >= 0) => (0-u32max >= 0)'
Obviously, it makes no sense to check if an unsigned int is >= 0. What
prevents this code from being a forever loop is that later there is a
separate check for if (queue == 0).
The "queue" variable is less than MTL_MAX_RX_QUEUES (8) so it can easily
fit in an int type. Any larger value for "queue" would lead to an array
overflow when we assign "rx_q = &priv->rx_queue[queue]".
Fixes: de0b90e52a ("net: stmmac: rearrange RX and TX desc init into per-queue basis")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220316083744.GB30941@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The 98DX2530 SoC is similar to the Armada 3700 except it needs a
different MBUS window configuration. Add a new compatible string to
identify this device and the required MBUS window configuration.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The out of band port on the 98DX2530 SoC is similar to the armada-3700
except it requires a slightly different MBUS window configuration. Add a
new compatible string so this difference can be accounted for.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Roi Dayan says:
====================
flow_offload: add tc vlan push_eth and pop_eth actions
Offloading vlan push_eth and pop_eth actions is needed in order to
correctly offload MPLSoUDP encap and decap flows, this series extends
the flow offload API to support these actions and updates mlx5 to
parse them.
====================
Link: https://lore.kernel.org/r/20220315110211.1581468-1-roid@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the MPLSoUDP encap offload does the L2 pop implicitly
while adding such action explicitly (vlan eth_push) will cause
the rule to not be offloaded.
Solve it by adding offload support for vlan eth_push in case of
MPLSoUDP decap case.
Flow example:
filter root protocol ip pref 1 flower chain 0
filter root protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 2.2.2.22
src_ip 2.2.2.21
in_hw in_hw_count 1
action order 1: vlan pop_eth pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 2: mpls push protocol mpls_uc label 555 tc 3 ttl 255 pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 3: tunnel_key set
src_ip 8.8.8.21
dst_ip 8.8.8.22
dst_port 6635
csum
tos 0x4
ttl 6 pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 4: mirred (Egress Redirect to device bareudp0) stolen
index 1 ref 1 bind 1
used_hw_stats delayed
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently action pedit of source and destination MACs is used
to fill the MACs in L2 push step in MPLSoUDP decap offload,
this isn't aligned to tc SW which use vlan eth_push action
to do this.
To fix that, offload support for vlan veth_push action is
added together with mpls pop action, and deprecate the use
of pedit of MACs.
Flow example:
filter protocol mpls_uc pref 1 flower chain 0
filter protocol mpls_uc pref 1 flower chain 0 handle 0x1
eth_type 8847
mpls_label 555
enc_dst_port 6635
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 2: mpls pop protocol ip pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 3: vlan push_eth dst_mac de:a2:ec:d6:69:c8 src_mac de:a2:ec:d6:69:c8 pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 4: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 2 ref 1 bind 1
used_hw_stats delayed
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
