Commit graph

327 commits

Author SHA1 Message Date
Yishai Hadas
c69453e294 net/mlx4_core: Manage interface state for Reset flow cases
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.

Implement the remove_one case, handling AER and other cases comes next.

The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
f5aef5aa35 net/mlx4_core: Activate reset flow upon fatal command cases
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.

The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.

In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.

The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.

Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
f6bc11e426 net/mlx4_core: Enhance the catas flow to support device reset
This includes:

- resetting the chip when a fatal error is detected (the current code
  does not do this).

- exposing the ability to enter error state from outside the catas code
  by calling its functionality. (E.g. FW Command timeout, AER error).

- managing a persistent device state. This is needed to sync between
  reset flow cases.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
ad9a0bf08f net/mlx4_core: Refactor the catas flow to work per device
Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.

This comes as a pre-patch for supporting chip reset
for both native and SRIOV.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
dd0eefe3ab net/mlx4_core: Set device configuration data to be persistent across reset
When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.

Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:13 -08:00
Yishai Hadas
872bf2fb69 net/mlx4_core: Maintain a persistent memory for mlx4 device
Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:13 -08:00
Richard Cochran
74d23cc704 time: move the timecounter/cyclecounter code into its own file.
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30 18:29:25 -05:00
Matan Barak
7d077cd34e net/mlx4: Add support for A0 steering
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.

The different A0 DMFS (steering) modes are:

Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.

Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.

Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).

Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.

Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.

In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-11 14:47:36 -05:00
Matan Barak
d57febe1a4 net/mlx4: Add A0 hybrid steering
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.

In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.

When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this  range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.

Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).

Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.

When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.

In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-11 14:47:35 -05:00
Eugenia Emantayev
ddae0349fd net/mlx4: Change QP allocation scheme
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.

The current Ethernet driver code reserves a Tx QP range with 256b alignment.

This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.

This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.

The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:

1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
   and request "BF enabled QPs" if BF is supported for the function

2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0]  - number of QPs
b. param1[31-24] - flags controlling QPs reservation

Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.

Bits 24-30 of the flags are currently reserved.

When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.

In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-11 14:47:35 -05:00
Matan Barak
3dca0f42c7 net/mlx4_core: Use tasklet for user-space CQ completion events
Previously, we've fired all our completion callbacks straight from our ISR.

Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.

In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-11 14:47:34 -05:00
Eric Dumazet
b9d1ab7eb4 mlx4: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.

Also provide ethtool -x support to fetch RSS key

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-16 15:59:13 -05:00
Matan Barak
de966c5928 net/mlx4_core: Support more than 64 VFs
We now allow up to 126 VFs. Note though that certain firmware
versions only allow up to 80 VFs. Moreover, old HCAs only support 64 VFs.
In these cases, we limit the maximum number of VFs to 64.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-13 15:16:22 -05:00
Matan Barak
7ae0e400cd net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.

Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.

Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-13 15:16:21 -05:00
Shani Michaeli
f8c6455bb0 net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE
When processing received traffic, pass CHECKSUM_COMPLETE status to the
stack, with calculated checksum for non TCP/UDP packets (such
as GRE or ICMP).

Although the stack expects checksum which doesn't include the pseudo
header, the HW adds it. To address that, we are subtracting the pseudo
header checksum from the checksum value provided by the HW.

In the IPv6 case, we also compute/add the IP header checksum which
is not added by the HW for such packets.

Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-11 13:20:02 -05:00
Matan Barak
d475c95b4b net/mlx4_core: Add retrieval of CONFIG_DEV parameters
Add code to issue CONFIG_DEV "get" firmware command.

This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.

The GET operation is allowed for VFs too.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-03 12:28:14 -05:00
Saeed Mahameed
a53e3e8c1d net/mlx4_core: Add ethernet backplane autoneg device capability
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28 17:18:00 -04:00
Saeed Mahameed
adbc7ac5c1 net/mlx4_core: Introduce ACCESS_REG CMD and eth_prot_ctrl dev cap
Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28 17:18:00 -04:00
Saeed Mahameed
32a173c7f9 net/mlx4_core: Introduce mlx4_get_module_info for cable module info reading
Added new MAD_IFC command to read cable module info with attribute id (0xFF60).
Update include/linux/mlx4/device.h with function declaration (mlx4_get_module_info)
and the needed defines/enums for future use.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28 17:17:59 -04:00
Eric Dumazet
7dfa4b414d net/mlx4_en: Code cleanups in tx path
- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-06 01:04:15 -04:00
Majd Dibbiny
e1c00e10e9 net/mlx4_core: New init and exit flow for mlx4_core
In the new flow, we separate the pci initialization and teardown
from the initialization and teardown of the other resources.

__mlx4_init_one handles the pci resources initialization. It then
calls mlx4_load_one to initialize the remainder of the resources.

When removing a device, mlx4_remove_one is invoked. However, now
mlx4_remove_one calls mlx4_unload_one to free all the resources except the pci
resources. When mlx4_unload_one returns, mlx4_remove_one then frees the
pci resources.

The above separation will allow us to implement 'reset flow' in the future.
It will also enable more EQs for VFs and is a pre-step to the modern API to
enable/disable SRIOV.

Also added nvfs; an integer array of size MLX4_MAX_PORTS + 1; to the mlx4_dev
struct. This new field is used to avoid parsing the num_vfs module parameter
each time the mlx4_restart_one is called.

Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30 16:27:49 -04:00
David S. Miller
1f6d80358d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	arch/mips/net/bpf_jit.c
	drivers/net/can/flexcan.c

Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-23 12:09:27 -04:00
Ido Shamay
77507aa249 net/mlx4_core: Enable CQE/EQE stride support
This feature is intended for archs having cache line larger then 64B.

Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.

Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:

1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment

This feature introduces two additional types:

3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)

Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).

The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-19 17:30:10 -04:00
Matan Barak
09e05c3f78 net/mlx4: Set vlan stripping policy by the right command
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.

Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.

Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10 15:21:34 -07:00
David S. Miller
eb84d6b604 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2014-09-07 21:41:53 -07:00
Or Gerlitz
b95089d00c net/mlx4: Move the tunnel steering helper function to mlx4_core
Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-29 20:13:00 -07:00
Amir Vadai
48ea526a68 net/mlx4: Use is_kdump_kernel() to detect kdump kernel
Use is_kdump_kernel() to detect kdump kernel, instead of reset_devices.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-25 15:42:19 -07:00
Linus Torvalds
e3b1fd56f1 Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
  - MAD support for RMPP in userspace
  - iSER and SRP initiator updates
  - ocrdma hardware driver updates
  - other fixes...
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCAAGBQJT7N2GAAoJEENa44ZhAt0hUiIQAKBqYIjpB3QY6Z/B19mxDxku
 I81B3OkirumbAaCLoLckvq4gnwQ+BAD+YUmXgP08TCIgrABZAYYw+WvMEY9WNyQB
 x3Pv+BzX+wKKNaQkSnB9JVdku+BSI76eW0YYrIX0F0x1o0Jq9JpSkia91KmRvqmX
 YSFy2R7BjEZ4lfo/uscydHT26Q6EdT3od4iv48K8qq5rKdjtyYNgD/75DLCN599Z
 uI1f98e6Tl+7nHWaioQB61zlYPkNPLAnZtMrY2j4tarTwYwX1KhF3eV7z39L1l81
 nhMIXr+qBXtYuZw3I9rKqw3VVCCqB9e6E8FIA5K/d2jWqO+0TqIMUYOuZXuCezWg
 o+uGgwbDOweBqwrKRmiR2M0lk2I1Z16jBxYuaUBbLImG0/NPtuUB22t6RbPAojTa
 EjDkb9XBA7uFUMrYYnou+HxEzmJUYkin6wgGxtklYEKUqvh8G9ccGt6httWrCSrV
 mpjwJv+S4LdFM49wdP993lYthpCoZ42yxEzZ7zJ/KTt17/Wb5F4RtHIROGVFkHdT
 mo8RUz5DGDznfNQgn0m/jC3woFnMNpLOduI+CivhrwrWCwMpSUxIjqWu3263pIJ7
 +H0kNOKDAbp6+F27j+AVznlyXnaEtYyM8EZnysG1Hkz24gCSWBYo5Ep8eSH8LgY4
 9VPc75KVG6uddx5mhg5h
 =wOm0
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull infiniband/rdma updates from Roland Dreier:
 "Main set of InfiniBand/RDMA updates for 3.17 merge window:

   - MR reregistration support
   - MAD support for RMPP in userspace
   - iSER and SRP initiator updates
   - ocrdma hardware driver updates
   - other fixes..."

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
  IB/srp: Fix return value check in srp_init_module()
  RDMA/ocrdma: report asic-id in query device
  RDMA/ocrdma: Update sli data structure for endianness
  RDMA/ocrdma: Obtain SL from device structure
  RDMA/uapi: Include socket.h in rdma_user_cm.h
  IB/srpt: Handle GID change events
  IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
  IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
  RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
  IPoIB: Remove unnecessary test for NULL before debugfs_remove()
  IB/mad: Add user space RMPP support
  IB/mad: add new ioctl to ABI to support new registration options
  IB/mad: Add dev_notice messages for various umad/mad registration failures
  IB/mad: Update module to [pr|dev]_* style print messages
  IB/ipoib: Avoid multicast join attempts with invalid P_key
  IB/umad: Update module to [pr|dev]_* style print messages
  IB/ipoib: Avoid flushing the workqueue from worker context
  IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
  IB/ipath: Add P_Key change event support
  mlx4_core: Add support for secure-host and SMP firewall
  ...
2014-08-14 11:09:05 -06:00
Roland Dreier
d087f6ad72 Merge branches 'core', 'cxgb4', 'ipoib', 'iser', 'iwcm', 'mad', 'misc', 'mlx4', 'mlx5', 'ocrdma' and 'srp' into for-next 2014-08-14 08:58:04 -07:00
Jack Morgenstein
114840c3d2 mlx4_core: Add support for secure-host and SMP firewall
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.

This is achieved by:
1. Not allowing un-trusted entities to access device configuration
   registers, directly (through pci_cr or pci_conf) and indirectly
   (through MADs).

2. Hiding M_Key from untrusted entities.

3. Preventing the modification of GUID0 by un-trusted entities

4. Not allowing drivers on untrusted hosts to receive nor to transmit
   packets over QP0 (SMP Firewall).

The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.

Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>

[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]

Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-08-05 07:40:22 -07:00
Matan Barak
e630664c83 mlx4_core: Add helper functions to support MR re-registration
Add few helper functions to support a mechanism of getting an MPT,
modifying it and updating the HCA with the modified object.

The code takes 2 paths, one for directly changing the MPT (and
sometimes its related MTTs) and another one which queries the MPT and
updates the HCA via fw command SW2HW_MPT. The first path is used in
native mode; the second path is slower and is used only in SRIOV.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-08-01 15:11:13 -07:00
Amir Vadai
2599d8580f net/mlx4_core: Use low memory profile on kdump kernel
When running in kdump kernel, reduce number of resources allocated for
the hardware. This will enable the NIC to operate in this low memory
environment at the expense of performance and some features not related
to the basic NIC functionality.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-22 19:53:14 -07:00
David S. Miller
1a98c69af1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-16 14:09:34 -07:00
Eugenia Emantayev
523ece889e net/mlx4_en: Fix set port ratelimit for 40GE
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.

For user set ratelimit <= 25 Gbps:
        use 100 Mbps units * user_ratelimit (* 10).

For user set ratelimit > 25 Gbps:
        use 1 Gbps units * user_ratelimit.

For user set unlimited ratelimit (0 Gbps):
        use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)

Note: any value > 58 will damage the FW ratelimit computation, so we allow
      a max and any higher value will be pulled down to 57.

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-08 19:58:44 -07:00
Amir Vadai
35f6f45368 net/mlx4_en: Don't use irq_affinity_notifier to track changes in IRQ affinity map
IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23 ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02 18:29:23 -07:00
Linus Torvalds
f9da455b93 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.

 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
    Benniston.

 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
    Mork.

 4) BPF now has a "random" opcode, from Chema Gonzalez.

 5) Add more BPF documentation and improve test framework, from Daniel
    Borkmann.

 6) Support TCP fastopen over ipv6, from Daniel Lee.

 7) Add software TSO helper functions and use them to support software
    TSO in mvneta and mv643xx_eth drivers.  From Ezequiel Garcia.

 8) Support software TSO in fec driver too, from Nimrod Andy.

 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.

10) Handle broadcasts more gracefully over macvlan when there are large
    numbers of interfaces configured, from Herbert Xu.

11) Allow more control over fwmark used for non-socket based responses,
    from Lorenzo Colitti.

12) Do TCP congestion window limiting based upon measurements, from Neal
    Cardwell.

13) Support busy polling in SCTP, from Neal Horman.

14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.

15) Bridge promisc mode handling improvements from Vlad Yasevich.

16) Don't use inetpeer entries to implement ID generation any more, it
    performs poorly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
  tcp: fixing TLP's FIN recovery
  net: fec: Add software TSO support
  net: fec: Add Scatter/gather support
  net: fec: Increase buffer descriptor entry number
  net: fec: Factorize feature setting
  net: fec: Enable IP header hardware checksum
  net: fec: Factorize the .xmit transmit function
  bridge: fix compile error when compiling without IPv6 support
  bridge: fix smatch warning / potential null pointer dereference
  via-rhine: fix full-duplex with autoneg disable
  bnx2x: Enlarge the dorq threshold for VFs
  bnx2x: Check for UNDI in uncommon branch
  bnx2x: Fix 1G-baseT link
  bnx2x: Fix link for KR with swapped polarity lane
  sctp: Fix sk_ack_backlog wrap-around problem
  net/core: Add VF link state control policy
  net/fsl: xgmac_mdio is dependent on OF_MDIO
  net/fsl: Make xgmac_mdio read error message useful
  net_sched: drr: warn when qdisc is not work conserving
  ...
2014-06-12 14:27:40 -07:00
Linus Torvalds
1d21b1bf53 Main batch of InfiniBand/RDMA changes for 3.16:
- Add iWARP port mapper to avoid conflicts between RDMA and normal
    stack TCP connections.
 
  - Fixes for i386 / x86-64 structure padding differences (ABI
    compatibility for 32-on-64) from Yann Droneaud.
 
  - A pile of SRP initiator fixes from Bart Van Assche.
 
  - Fixes for a writeback / memory allocation deadlock with NFS over
    IPoIB connected mode from Jiri Kosina.
 
  - The usual fixes and cleanups to mlx4, mlx5, cxgb4 and other
    low-level drivers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCAAGBQJTlzyEAAoJEENa44ZhAt0h9yoP/1UeXlejOpCJyiNdtJZ+ilcU
 cb0PEzsjzqACyDqcoQ0EpQM3/3emccVIC3uUXK12mzlTIXOFYTeRLays/TbxZDLt
 FK5D/NrMmmJmciPt1ZRgUX82kFFRGScEfpkXYs7jxtRaNT7CW5KwSNQr6aFXskUz
 1gpdK1ARCN5rWcGl2HJx5o9C4c/Fa/Vov8lOsAkUZXD1SuPNT/fFN0u1pRzU68g0
 k3oj81XnZq5ejOBQKXEHImcmjXwaJ2yjmzxhSsKebqDWDdXuS/F9e4taKneHTZmr
 AdwJaLLJPWmAGi/vYYhkuLKpzIDpzMCqwr39lEabmjWvznYOlnjfVUXwUTE2nwNC
 DIXuHOLFrSvF2cNxh8ZeEYKS8AV+PjAOahPC5whkWkY256Q67uB7cy9ilWAK+7xS
 QcQ5Inr6iXvxIGYA4hNwUo8aK0NuKFwhkVVFEbkPaurbQZPqiKwyVE3w2FOws/Qp
 0kLLCVvpRQYjKzkxyof2tb1AcNuVNKXHrYk6RaBDJ9mjxHbhvY4OSt4CBxAAXBu6
 zoedUydN1Nz1UgAB1jDsBdyE2QQnXockA1+JJKNq6gM5Dz0DUdAylzQ2NqY9tnYz
 RTzihEPYIiQUkV3B8ErbqsuO6z7M830AXO5AR6bLZn1zgJ0cbMLBaKLA8LRufJI/
 qxNVwL32Uv1PjKZ+yX1x
 =Wcdc
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull main InfiniBand/RDMA updates from Roland Dreier:

 - add iWARP port mapper to avoid conflicts between RDMA and normal
   stack TCP connections.

 - fixes for i386 / x86-64 structure padding differences (ABI
   compatibility for 32-on-64) from Yann Droneaud.

 - a pile of SRP initiator fixes from Bart Van Assche.

 - fixes for a writeback / memory allocation deadlock with NFS over
   IPoIB connected mode from Jiri Kosina.

 - the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
   drivers.

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
  RDMA/cxgb4: Add support for iWARP Port Mapper user space service
  RDMA/nes: Add support for iWARP Port Mapper user space service
  RDMA/core: Add support for iWARP Port Mapper user space service
  IB/mlx4: Fix gfp passing in create_qp_common()
  IB/umad: Fix use-after-free on close
  IB/core: Fix kobject leak on device register error flow
  RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
  mlx4_core: Fix GFP flags parameters to be gfp_t
  IB/core: Fix port kobject deletion during error flow
  IB/core: Remove unneeded kobject_get/put calls
  IB/core: Fix sparse warnings about redeclared functions
  IB/mad: Fix sparse warning about gfp_t use
  IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
  IB: Add a QP creation flag to use GFP_NOIO allocations
  IB: Return error for unsupported QP creation flags
  IB: Allow build of hw/ and ulp/ subdirectories independently
  mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
  RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
  IB/srp: Avoid problems if a header uses pr_fmt
  IB/umad: Fix error handling
  ...
2014-06-10 10:41:33 -07:00
Roland Dreier
eeaddf3670 Merge branches 'core', 'cxgb3', 'cxgb4', 'iser', 'iwpm', 'misc', 'mlx4', 'mlx5', 'noio', 'ocrdma', 'qib', 'srp' and 'usnic' into for-next 2014-06-10 10:12:14 -07:00
Jiri Kosina
40f2287bd5 IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive.  Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-06-02 14:58:11 -07:00
David S. Miller
96b2e73c54 Revert "net/mlx4_en: Use affinity hint"
This reverts commit 70a640d0da.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 00:18:48 -07:00
Yuval Atias
70a640d0da net/mlx4_en: Use affinity hint
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.

Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01 19:16:29 -07:00
Jack Morgenstein
65fed8a8c1 IB/mlx4: Add interface for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.

By default, no VFs are enabled for QP0 operation.

To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:

- smi_enabled (read-only). Indicates whether smi is currently
  enabled for the indicated VF/port

- enable_smi_admin (rw). Used by the admin to request that smi
  capability be enabled or disabled for the indicated VF/port.
  0 = disable, 1 = enable.
  The requested enablement will occur at the next reset of the
  VF (e.g. driver restart on the VM which owns the VF).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:19 -07:00
Jack Morgenstein
99ec41d0a4 mlx4: Add infrastructure for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:09 -07:00
Jack Morgenstein
97982f5a91 IB/mlx4: Preparation for VFs to issue/receive SMI (QP0) requests/responses
Currently, VFs in SRIOV VFs are denied QP0 access.  The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology.  Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.

However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.

This commit does the following:

1. Create QP0 tunnel QPs for all VFs.

2. Discard SMI mads sent-from/received-for non-privileged VFs in the
   hypervisor MAD multiplex/demultiplex logic.  SMI mads from/for
   privileged VFs are allowed to pass.

3. MAD_IFC wrapper changes/fixes.  For non-privileged VFs, only
   host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
   GET mads.  For privileged VFs, there are no restrictions.

This commit does not allow privileged VFs as yet.  To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled().  This function
returns 0 unconditionally for now.

The next two commits allow defining and activating privileged VFs.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:12:58 -07:00
David S. Miller
54e5c4def0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/bonding/bond_alb.c
	drivers/net/ethernet/altera/altera_msgdma.c
	drivers/net/ethernet/altera/altera_sgdma.c
	net/ipv6/xfrm6_output.c

Several cases of overlapping changes.

The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.

In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.

Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 00:32:30 -04:00
Amir Vadai
ecc8fb11cd net/mlx4_core: Deprecate use_prio module parameter
use_prio was added as part of an infrastructure for running FCoE in A0 mode.
FCoE didn't get into Mellanox Upstream driver, and when it will, it won't be
using A0 steering mode.

Therefore we can safely deprecate this module parameter without hurting any
existing user.

CC: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-22 17:17:29 -04:00
Matan Barak
ce8d9e0d67 net/mlx4_core: Add UPDATE_QP SRIOV wrapper support
This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:12:45 -04:00
Yuval Atias
2eacc23c42 net/mlx4_core: Enforce irq affinity changes immediatly
During heavy traffic, napi is constatntly polling the complition queue
and no interrupt is fired. Because of that, changes to irq affinity are
ignored until traffic is stopped and resumed.

By registering to the irq notifier mechanism, and forcing interrupt when
affinity is changed, irq affinity changes will be immediatly enforced.

Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 15:40:32 -04:00
Or Gerlitz
1b136de120 net/mlx4: Implement vxlan ndo calls
Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 16:29:35 -04:00
Or Gerlitz
d18f141a1a mlx4: Add support for CONFIG_DEV command
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 16:29:35 -04:00
Matan Barak
449fc48866 net/mlx4: Adapt code for N-Port VF
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-20 16:18:30 -04:00
Matan Barak
f74462acf8 net/mlx4: Add utils for N-Port VFs
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-20 16:18:29 -04:00
Matan Barak
1ab95d37bc net/mlx4: Add data structures to support N-Ports per VF
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-20 16:18:29 -04:00
Jack Morgenstein
5ea8bbfc49 mlx4: Implement IP based gids support for RoCE/SRIOV
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.

Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-12 15:57:16 -04:00
Jack Morgenstein
b6ffaeffae mlx4: In RoCE allow guests to have multiple GIDS
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs:  Remaining GIDS are divided evenly between VFs activated by the driver.
      If the division is not even, lower-numbered VFs get an extra GID.

For an IB interface, the number of gids per guest remains as before: one gid per guest.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-12 15:57:14 -04:00
Jack Morgenstein
9cd593529c mlx4_core: For RoCE, allow slaves to set the GID entry at that slave's index
For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.

In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").

This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-12 15:57:13 -04:00
Jack Morgenstein
6ee51a4e86 mlx4: Adjust QP1 multiplexing for RoCE/SRIOV
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.

This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-12 15:57:12 -04:00
Amir Vadai
ec5709403e net/mlx4_en: Use union for BlueFlame WQE
When BlueFlame is turned on, control segment of the TX WQE is changed,
and the second line of it is used for QPN.
Changed code to use a union in the mlx4_wqe_ctrl_seg instead of casting.
This makes the code clearer and solves the static checker warning:

drivers/net/ethernet/mellanox/mlx4/en_tx.c:839 mlx4_en_xmit()
	warn: potential memory corrupting cast 4 vs 2 bytes

CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 20:04:01 -05:00
Eugenia Emantayev
9813337a4b net/mlx4: Replace mlx4_en_mac_to_u64() with mlx4_mac_to_u64()
Currently, the EN driver uses a private static function
mlx4_en_mac_to_u64(). Move it to a common include file (driver.h)
for mlx4_en and mlx4_ib for further use.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 20:04:01 -05:00
Linus Torvalds
4ba9920e5e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) BPF debugger and asm tool by Daniel Borkmann.

 2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.

 3) Correct reciprocal_divide and update users, from Hannes Frederic
    Sowa and Daniel Borkmann.

 4) Currently we only have a "set" operation for the hw timestamp socket
    ioctl, add a "get" operation to match.  From Ben Hutchings.

 5) Add better trace events for debugging driver datapath problems, also
    from Ben Hutchings.

 6) Implement auto corking in TCP, from Eric Dumazet.  Basically, if we
    have a small send and a previous packet is already in the qdisc or
    device queue, defer until TX completion or we get more data.

 7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.

 8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
    Borkmann.

 9) Share IP header compression code between Bluetooth and IEEE802154
    layers, from Jukka Rissanen.

10) Fix ipv6 router reachability probing, from Jiri Benc.

11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.

12) Support tunneling in GRO layer, from Jerry Chu.

13) Allow bonding to be configured fully using netlink, from Scott
    Feldman.

14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
    already get the TCI.  From Atzm Watanabe.

15) New "Heavy Hitter" qdisc, from Terry Lam.

16) Significantly improve the IPSEC support in pktgen, from Fan Du.

17) Allow ipv4 tunnels to cache routes, just like sockets.  From Tom
    Herbert.

18) Add Proportional Integral Enhanced packet scheduler, from Vijay
    Subramanian.

19) Allow openvswitch to mmap'd netlink, from Thomas Graf.

20) Key TCP metrics blobs also by source address, not just destination
    address.  From Christoph Paasch.

21) Support 10G in generic phylib.  From Andy Fleming.

22) Try to short-circuit GRO flow compares using device provided RX
    hash, if provided.  From Tom Herbert.

The wireless and netfilter folks have been busy little bees too.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
  net/cxgb4: Fix referencing freed adapter
  ipv6: reallocate addrconf router for ipv6 address when lo device up
  fib_frontend: fix possible NULL pointer dereference
  rtnetlink: remove IFLA_BOND_SLAVE definition
  rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
  qlcnic: update version to 5.3.55
  qlcnic: Enhance logic to calculate msix vectors.
  qlcnic: Refactor interrupt coalescing code for all adapters.
  qlcnic: Update poll controller code path
  qlcnic: Interrupt code cleanup
  qlcnic: Enhance Tx timeout debugging.
  qlcnic: Use bool for rx_mac_learn.
  bonding: fix u64 division
  rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
  sfc: Use the correct maximum TX DMA ring size for SFC9100
  Add Shradha Shah as the sfc driver maintainer.
  net/vxlan: Share RX skb de-marking and checksum checks with ovs
  tulip: cleanup by using ARRAY_SIZE()
  ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
  net/cxgb4: Don't retrieve stats during recovery
  ...
2014-01-25 11:17:34 -08:00
Roland Dreier
fb1b5034e4 Merge branch 'ip-roce' into for-next
Conflicts:
	drivers/infiniband/hw/mlx4/main.c
2014-01-22 23:24:21 -08:00
Moni Shoua
297e0dad72 IB/mlx4: Handle Ethernet L2 parameters for IP based GID addressing
IP based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.

Therefore, we need to extract them from the CQE and place them in
struct ib_wc (to be used for cases were they were taken from the gid).

Also, when modifying a QP or building address handle, instead of
parsing the dgid to get the MAC and VLAN, take them from the address
handle attributes.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-01-18 14:12:53 -08:00
Matan Barak
dd5f03beb4 IB/core: Ethernet L2 attributes in verbs/cm structures
This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.

When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.

Thus, those attributes were added to the following structures:

* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id

For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.

On the active side, the CM fills. its internal structures from the
path provided by the ULP.  We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).

On the passive side, the CM fills its internal structures from the WC
associated with the REQ message.  We add there taking the ETH L2
attributes from the WC.

When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.

ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB.  Vendor drivers are modified to support the new
function signature.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-01-14 14:20:54 -08:00
Matan Barak
4de6580360 mlx4_core: Add support for steerable IB UD QPs
This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-01-14 14:06:50 -08:00
Or Gerlitz
7ffdf726cf net/mlx4_core: Add basic support for TCP/IP offloads under tunneling
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-31 14:31:43 -05:00
Hadar Hen Zion
8e1a28e8e6 net/mlx4_core: Expose physical port id as PF/VF capability
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-19 19:04:43 -05:00
Eugenia Emantayev
163561a4e2 net/mlx4_en: Datapath structures are allocated per NUMA node
For each RX/TX ring and its CQ, allocation is done on a NUMA node that
corresponds to the core that the data structure should operate on.
The assumption is that the core number is reflected by the ring index.
The affected allocations are the ring/CQ data structures,
the TX/RX info and the shared HW/SW buffer.
For TX rings, each core has rings of all UPs.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-07 19:22:48 -05:00
Eugenia Emantayev
6e7136ed77 net/mlx4_core: ICM pages are allocated on device NUMA node
This is done to optimize FW/HW access to host memory.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-07 19:22:48 -05:00
Jack Morgenstein
5a0d0a6161 mlx4: Structures and init/teardown for VF resource quotas
This is step #1 for implementing SRIOV resource quotas for VFs.

Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.

Resources which are allocated using quotas:  QPs, CQs, SRQs, MPTs, MTTs, MAC,
                                             VLAN, and Counters.

The quota system works as follows:
Each entity (VF or PF) is given a max number of a given resource (its quota),
and a guaranteed minimum number for each resource (starvation prevention).

For QPs, CQs, SRQs, MPTs and MTTs:
50% of the available quantity for the resource is divided equally among
the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module
parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool.
The other 50% is the "free pool", allocated on a first-come-first-serve basis.
For each VF/PF, resources are first allocated from its "guaranteed-minimum"
pool. When that pool is exhausted, the driver attempts to allocate from
the resource "free-pool".

The quota (i.e., max) for the VFs and the PF is:
  The free-pool amount (50% of the real max) + the guaranteed minimum

For MACs:
  Guarantee 2 MACs per VF/PF per port. As a result, since we have only
  128 MACs per port, reduce the allowable number of VFs from 64 to 63.
  Any remaining MACs are put into a free pool.

For VLANs:
  For the PF, the per-port quota is 128 and guarantee is 64
     (to allow the PF to register at least a VLAN per VF in VST mode).
  For the VFs, the per-port quota is 64 and the guarantee is 0.
      We assume that VGT VFs are trusted not to abuse the VLAN resource.

For Counters:
  For all functions (PF and VFs), the quota is 128 and the guarantee is 0.

In this patch, we define the needed structures, which are added to the
resource-tracker struct.  In addition, we do initialization
for the resource quota, and adjust the query_device response to use quotas
rather than resource maxima.

As part of the implementation, we introduce a new field in
mlx4_dev: quotas.  This field holds the resource quotas used
to report maxima to the upper layers (ib_core, via query_device).

The HCA maxima of these values are passed to the VFs (via
QUERY_HCA) so that they may continue to use these in handling
QPs, CQs, SRQs and MPTs.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 16:19:07 -05:00
Jack Morgenstein
2009d0059c net/mlx4_en: Use vlan id instead of vlan index for unregistration
Use of vlan_index created problems unregistering vlans on guests.

In addition, tools delete vlan by tag, not by index, lets follow that.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 16:19:07 -05:00
Jack Morgenstein
acddd5dd44 net/mlx4_core: Fix reg/unreg vlan/mac to conform to the firmware spec
The functions mlx4_register_vlan, mlx4_unregister_vlan, mlx4_register_mac,
mlx4_unregister_mac all made illegal use of the out_param in multifunc mode
to pass the port number. The firmware spec specifies that the port number
should be passed in bits 8..15 of the input-modifier field for ALLOC_RES and
FREE_RES (sections 20.15.1 and 20.15.2).

For MAC register/unregister, this patch contains workarounds so that guests
running previous kernels continue to work on a new Hypervisor, and guests
running the new kernel will continue to work on old hypervisors.

Vlan registeration capability is still not operational in multifunction mode,
since the vlan wrapper functions are not implemented in this patch.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 16:19:06 -05:00
Or Gerlitz
5930e8d0ab net/mlx4: Fix typo, move similar defs to same location
Small code cleanup:

1. change MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN to MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN

2. put MLX4_SET_PORT_PRIO2TC and MLX4_SET_PORT_SCHEDULER in the same union with the
   other MLX4_SET_PORT_yyy

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-17 15:10:50 -04:00
Linus Torvalds
cc998ff881 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David Miller:
 "Noteworthy changes this time around:

   1) Multicast rejoin support for team driver, from Jiri Pirko.

   2) Centralize and simplify TCP RTT measurement handling in order to
      reduce the impact of bad RTO seeding from SYN/ACKs.  Also, when
      both timestamps and local RTT measurements are available prefer
      the later because there are broken middleware devices which
      scramble the timestamp.

      From Yuchung Cheng.

   3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
      memory consumed to queue up unsend user data.  From Eric Dumazet.

   4) Add a "physical port ID" abstraction for network devices, from
      Jiri Pirko.

   5) Add a "suppress" operation to influence fib_rules lookups, from
      Stefan Tomanek.

   6) Add a networking development FAQ, from Paul Gortmaker.

   7) Extend the information provided by tcp_probe and add ipv6 support,
      from Daniel Borkmann.

   8) Use RCU locking more extensively in openvswitch data paths, from
      Pravin B Shelar.

   9) Add SCTP support to openvswitch, from Joe Stringer.

  10) Add EF10 chip support to SFC driver, from Ben Hutchings.

  11) Add new SYNPROXY netfilter target, from Patrick McHardy.

  12) Compute a rate approximation for sending in TCP sockets, and use
      this to more intelligently coalesce TSO frames.  Furthermore, add
      a new packet scheduler which takes advantage of this estimate when
      available.  From Eric Dumazet.

  13) Allow AF_PACKET fanouts with random selection, from Daniel
      Borkmann.

  14) Add ipv6 support to vxlan driver, from Cong Wang"

Resolved conflicts as per discussion.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
  openvswitch: Fix alignment of struct sw_flow_key.
  netfilter: Fix build errors with xt_socket.c
  tcp: Add missing braces to do_tcp_setsockopt
  caif: Add missing braces to multiline if in cfctrl_linkup_request
  bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
  vxlan: Fix kernel panic on device delete.
  net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
  net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
  icplus: Use netif_running to determine device state
  ethernet/arc/arc_emac: Fix huge delays in large file copies
  tuntap: orphan frags before trying to set tx timestamp
  tuntap: purge socket error queue on detach
  qlcnic: use standard NAPI weights
  ipv6:introduce function to find route for redirect
  bnx2x: VF RSS support - VF side
  bnx2x: VF RSS support - PF side
  vxlan: Notify drivers for listening UDP port changes
  net: usbnet: update addr_assign_type if appropriate
  driver/net: enic: update enic maintainers and driver
  driver/net: enic: Exposing symbols for Cisco's low latency driver
  ...
2013-09-05 14:54:29 -07:00
Hadar Hen Zion
f77c0162a3 IB/mlx4: Add receive flow steering support
Implement ib_create_flow() and ib_destroy_flow().

Translate the verbs structures provided by the user to HW structures
and call the MLX4_QP_FLOW_STEERING_ATTACH/DETACH firmware commands.

On the ATTACH command completion, the firmware provides a 64-bit
registration ID, which is placed into struct mlx4_ib_flow that wraps
the instance of struct ib_flow which is retuned to caller.  Later,
this reg ID is used for detaching that flow from the firmware.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-08-28 09:53:56 -07:00
Joe Perches
574e2af7c0 include: Convert ethernet mac address declarations to use ETH_ALEN
It's convenient to have ethernet mac addresses use
ETH_ALEN to be able to grep for them a bit easier and
also to ensure that the addresses are __aligned(2).

Add #include <linux/if_ether.h> as necessary.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-02 12:33:54 -07:00
Yevgeny Petrilin
fe6f700d6c net/mlx4_core: Respond to operation request by firmware
This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-29 01:12:40 -07:00
Rony Efraim
0a6eac2458 net/mlx4_core: Add HW enforcement to VF link state
When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-01 13:10:57 -07:00
Jack Morgenstein
b01978cacf net/mlx4_core: Dynamic VST to VST vlan/qos changes
Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.

This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).

To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.

If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-01 13:10:22 -07:00
Rony Efraim
948e306d7d net/mlx4: Add VF link state support
Add support to change the link state of VF (vPort)

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-13 17:51:04 -07:00
Rony Efraim
7677fc965f net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
Make sure that the following steps are taken:

- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set

Use enum values for all the above instead of numerical bit offsets.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-11 16:12:44 -07:00
Linus Torvalds
e0fd9affeb InfiniBand/RDMA changes for the 3.10 merge window:
- XRC transport fixes
  - Fix DHCP on IPoIB
  - mlx4 preparations for flow steering
  - iSER fixes
  - miscellaneous other fixes
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABCAAGBQJRisChAAoJEENa44ZhAt0hHLoP/iX5MxtHJ3X1u5KcARX/7nci
 CCH/VnD172re/KavCCg7zkbZQpS4jHCtW/CzLUCSPqBGOaj78HFTUkB3ragvUW7m
 ndERwplF8DP/i0x7Kk7Wau2a4RdlH0lqwucOjqTyQnbIdxknkz6w3Jcsb9Ic2lzx
 up0T0HaHtTxdVF6lXOB5QOIpUGg3l0Yu4euX2BA61WDoZj+VIYhgeWZewq0iV0D1
 rLtarJ+Or7mdwu2rNcDHgrD0lhF4SCBd3rx4lbc4F68Cr8JUz0Xe7liPLNskeLhW
 f3NEm3gmkYp9YI1otGsA0X/CyV6wnRk4mT8JMlOb2WNzeq2V13Z54/9ZyF5/gFD2
 JgzkQB9Ibf7EmTwXWd6+0+FA40Q6dNvnRnhddRM255dvDVw7nxUr2UzYH4Re/Z9K
 rNFjkvix2YUwEmoPjitWocz2kj2reDMqjtiVDmdGy1YbtnicH5GtkQsWkoPg8ON9
 m5jORUdzydTD+yBJwTiFP1EuFoG3TdfoZ7zHMJwWy/u8i308xD6WPGms9MTdjh8j
 7gjz2TCKr+vpuVRh/p6esCPPOTSsSeWDeowy7Sgpdf3qoqAImXsWXVrl2kXLhtyl
 1VIgHU3ztm7oqwmy0gQ/zVCo4CLLdsif2zmEIDpxJPnWaSq+D9LJdyLTcfdBjhQ8
 9SjUafe4msT1pIjNb7ND
 =1ojD
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull InfiniBand/RDMA changes from Roland Dreier:
 - XRC transport fixes
 - Fix DHCP on IPoIB
 - mlx4 preparations for flow steering
 - iSER fixes
 - miscellaneous other fixes

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
  IB/iser: Add support for iser CM REQ additional info
  IB/iser: Return error to upper layers on EAGAIN registration failures
  IB/iser: Move informational messages from error to info level
  IB/iser: Add module version
  mlx4_core: Expose a few helpers to fill DMFS HW strucutures
  mlx4_core: Directly expose fields of DMFS HW rule control segment
  mlx4_core: Change a few DMFS fields names to match firmare spec
  mlx4: Match DMFS promiscuous field names to firmware spec
  mlx4_core: Move DMFS HW structs to common header file
  IB/mlx4: Set link type for RAW PACKET QPs in the QP context
  IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
  mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
  RDMA/iwcm: Don't touch cmid after dropping reference
  IB/qib: Correct qib_verbs_register_sysfs() error handling
  IB/ipath: Correct ipath_verbs_register_sysfs() error handling
  RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
  SRPT: Fix odd use of WARN_ON()
  IPoIB: Fix ipoib_hard_header() return value
  RDMA: Rename random32() to prandom_u32()
  RDMA/cxgb3: Fix uninitialized variable
  ...
2013-05-08 15:29:48 -07:00
Rony Efraim
2cccb9e4f3 net/mlx4: Add support to get VF config
Support getting VF config.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:14 -04:00
Rony Efraim
e6b6a23163 net/mlx4: Add VF MAC spoof checking support
Add ndo_set_vf_spoofchk support

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:14 -04:00
Rony Efraim
3f7fb021d0 net/mlx4: Add set VF default vlan ID and priority support
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.

The special values of VID=4095 or VID=0,UP=0 are considered as VGT.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:13 -04:00
Rony Efraim
8f7ba3ca12 net/mlx4: Add set VF mac address support
Add ndo_set_vf_mac support which allows to set the MAC address
for mlx4 VF Ethernet NICs from the host.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:13 -04:00
Hadar Hen Zion
c2c19dc3c9 mlx4_core: Expose a few helpers to fill DMFS HW strucutures
Re-arrange some of code which fills DMFS HW structures so we can use
it from within the core driver and from the IB driver too, e.g when
verbs DMFS structures are transformed into mlx4 hardware structs.

Also, add struct mlx4_flow_handle struct which will be of use by the
DMFS verbs flow in the IB driver.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-24 17:51:30 -07:00
Hadar Hen Zion
bcf372971d mlx4_core: Directly expose fields of DMFS HW rule control segment
Some of struct mlx4_net_trans_rule_hw_ctrl fields were packed into u32
and accessed through bit field operations.  Expose and access them
directly as u8 or u16.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-24 17:51:29 -07:00
Hadar Hen Zion
ba60a3560c mlx4_core: Change a few DMFS fields names to match firmare spec
Change struct mlx4_net_trans_rule_hw_eth :: vlan_id name to vlan_tag

Change struct mlx4_net_trans_rule_hw_ib :: r_u_qpn name to l3_qpn

The patch doesn't introduce any functional change or API change
towards the firmware.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-24 17:51:29 -07:00
Hadar Hen Zion
f91625398a mlx4: Match DMFS promiscuous field names to firmware spec
Align the names used by enum mlx4_net_trans_promisc_mode with the
actual firmware specification.  The patch doesn't introduce any
functional change or API change towards the firmware.

Remove MLX4_FS_PROMISC_FUNCTION_PORT which isn't of use.  Add new
enums MLX4_FS_{UC/MC}_SNIFFER as a preparation step for sniffer
support.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-24 17:51:29 -07:00
Hadar Hen Zion
3cd0e1789a mlx4_core: Move DMFS HW structs to common header file
Move flow steering HW structures to be on the public mlx4 include
directory, as a pre-step for the mlx4 IB driver to use them too.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-24 17:51:28 -07:00
Amir Vadai
ec693d4701 net/mlx4_en: Add HW timestamping (TS) support
The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-24 16:30:14 -04:00
Eugenia Emantayev
ddd8a6c12d net/mlx4_core: Read HCA frequency and map internal clock
Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-24 16:30:13 -04:00
Eugenia Emantayev
d998735f44 net/mlx4_core: Add timestamping device capability
Add new device capability for timestamping support and query FW to retrieve it.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-24 16:30:13 -04:00
Shlomo Pongratz
9f550553a4 mlx4_core: Implement SRQ object lookup from srqn
Expose a new API mlx4_srq_lookup() to retrive a SRQ based on its
number.  This API is needed in the mlx4_ib driver CQ polling logic,
when a work completion is associated with a XRC TGT QP.  Since a
target QP may redirect to more than one XRC SRQ, the srq field in the
QP has no usage and the real XRC SRQ need to be retrived using the
information from the XRCETH IB header which is placed in the HW CQE.

Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-04-16 22:42:55 -07:00
Or Gerlitz
540b3a39ee net/mlx4_en: Enable DCB ETS ops only when supported by the firmware
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07 16:55:46 -04:00
Linus Torvalds
70a3a06d01 Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
  - Implementation of memory windows for mlx4 from Shani Michaeli
  - Lots of cxgb4 HW driver fixes from Vipul Pandya
  - Make iSER work for virtual functions, other fixes from Or Gerlitz
  - Fix for bug in qib HW driver from Mike Marciniszyn
  - IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
  - Various cleanups and warning fixes from Julia Lawall, Paul Bolle, Wei Yongjun
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABCAAGBQJRLPNoAAoJEENa44ZhAt0h0bMP/1xqlgDR3DGdoUoV4yTd6O9G
 Uccdb7og5o5tedVo+8xZz01y4at99P8FWW4hJ4os6k8n6yKoBVwo7qjN+BOR+JG5
 q8+O+ynUSIg4tGrb5sXcMnKXAXbw/vkftMWYNA41cbrM24DTYzB/2SLpvhwbFoTT
 tdQc2tgz5QaDqzWbagyCR4+k/IgO+Llrz/RvIdtz4dsTnTDogN7QCoSffX8n/Lpb
 DxtyXK4sdl3DAtd3CsIdsB/TSMb3RkHLCoSvmrWlLnqMdsbRxVnCVfBm4BOghW3J
 Y2K3joRoCjjIZSRNs/i0FMFkT/jbCXg1oXg9ek/a6YFNcgyk7z8iGyXrRY7fOnno
 8U2SfxJ69YpVYeJr+DSjaeHcmjsaYU7NN7JPxzvPKcJOIsxQJ/euJDXAXau3lEQY
 o9/p4JsGty0WHi1NanyygvghvBAoP1C5/59Sl4bHH5gckPyJT1kinPSCTT76YXGS
 WkSHg2mDhiJHy7Pnuy85iZldPoy2/5z09/I4aGMeL+8kUZbD4iFqzXIJU0HTsAim
 EONoRXDhIcN5DNVSVH1ig6nJ2a7Vhov4Z0r/vB8P4KhslBcqFwf2leC0eCoe5mNt
 SzcKhqosZDXoL8AwzpntzGIOid8pWmHbUx/PgIcoVXPjtl0h2ULNIFoYYyMZ3cyU
 AyN2tSiUZVddTV1/aKGL
 =RAQw
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull infiniband update from Roland Dreier:
 "Main batch of InfiniBand/RDMA changes for 3.9:

   - SRP error handling fixes from Bart Van Assche

   - Implementation of memory windows for mlx4 from Shani Michaeli

   - Lots of cxgb4 HW driver fixes from Vipul Pandya

   - Make iSER work for virtual functions, other fixes from Or Gerlitz

   - Fix for bug in qib HW driver from Mike Marciniszyn

   - IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman

   - Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
     Wei Yongjun"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
  IB/mlx4: Advertise MW support
  IB/mlx4: Support memory window binding
  mlx4: Implement memory windows allocation and deallocation
  mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
  mlx4_core: Disable memory windows for virtual functions
  IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
  IB/srp: Fail I/O requests if the transport is offline
  IB/srp: Avoid endless SCSI error handling loop
  IB/srp: Avoid sending a task management function needlessly
  IB/srp: Track connection state properly
  IB/mlx4: Remove redundant NULL check before kfree
  IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
  IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
  IB/iser: Enable iser when FMRs are not supported
  IB/iser: Avoid error prints on EAGAIN registration failures
  IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
  IB/uverbs: Implement memory windows support in uverbs
  IB/core: Add "type 2" memory windows support
  mlx4_core: Propagate MR deregistration failures to caller
  mlx4_core: Rename MPT-related functions to have mpt_ prefix
  ...
2013-02-26 11:41:08 -08:00
Shani Michaeli
6ff63e1940 IB/mlx4: Support memory window binding
* Implement memory windows binding in mlx4_ib_post_send.

* Implement mlx4_ib_bind_mw by deferring to mlx4_ib_post_send.

* Rename MLX4_WQE_FMR_PERM_* flags to MLX4_WQE_FMR_AND_BIND_PERM_*,
  indicating that they are used both for fast registration work
  requests, and for memory window bind work requests.

Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-02-25 10:44:32 -08:00
Shani Michaeli
804d6a89a5 mlx4: Implement memory windows allocation and deallocation
Implement MW allocation and deallocation in mlx4_core and mlx4_ib.
Pass down the enable bind flag when registering memory regions.

Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-02-25 10:44:32 -08:00
Shani Michaeli
6108372070 mlx4_core: Propagate MR deregistration failures to caller
MR deregistration fails when memory windows are bound to the MR.
Handle such failures by propagating them to the caller ULP.

Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-02-21 11:38:43 -08:00
Shani Michaeli
aee38fadd2 IB/mlx4_ib: Remove local invalidate segment unused fields
Remove unused fields from the local invalidate WQE segment structure.

Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2013-02-21 11:36:29 -08:00
Yan Burman
16a10ffd20 net/mlx4: Move Ethernet related functionality from mlx4_core to mlx4_en
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.

Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp

To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)

Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-07 23:26:12 -05:00
Matan Barak
955154fa33 net/mlx4_en: Don't reassign port mac address on firmware that supports it
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-31 12:48:47 -05:00
Jack Morgenstein
3c439b5586 mlx4_core: Allow choosing flow steering mode
Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering).  If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-12-19 11:47:22 -08:00
Or Gerlitz
08ff32352d mlx4: 64-byte CQE/EQE support
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs).  Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline.  This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.

The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.

Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.

In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.

The SRIOV related flow is as follows

1. the PPF does the detection of the new capabilities using
   QUERY_DEV_CAP command.

2. the PPF activates the new capabilities using INIT_HCA.

3. the VF detects if the PPF activated the capabilities using
   QUERY_HCA, and if this is the case activates them for itself too.

Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP.  Steps 1 and 2 apply also for native mode.

User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.

In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-11-26 10:19:17 -08:00
Jack Morgenstein
47605df953 mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
Previously, the structure of a guest's proxy QPs followed the
structure of the PPF special qps (qp0 port 1, qp0 port 2, qp1 port 1,
qp1 port 2, ...).  The guest then did offset calculations on the
sqp_base qp number that the PPF passed to it in QUERY_FUNC_CAP().

This is now changed so that the guest does no offset calculations
regarding proxy or tunnel QPs to use.  This change frees the PPF from
needing to adhere to a specific order in allocating proxy and tunnel
QPs.

Now QUERY_FUNC_CAP provides each port individually with its proxy
qp0, proxy qp1, tunnel qp0, and tunnel qp1 QP numbers, and these are
used directly where required (with no offset calculations).

To accomplish this change, several fields were added to the phys_caps
structure for use by the PPF and by non-SR-IOV mode:

    base_sqpn -- in non-sriov mode, this was formerly sqp_start.
    base_proxy_sqpn -- the first physical proxy qp number -- used by PPF
    base_tunnel_sqpn -- the first physical tunnel qp number -- used by PPF.

The current code in the PPF still adheres to the previous layout of
sqps, proxy-sqps and tunnel-sqps.  However, the PPF can change this
layout without affecting VF or (paravirtualized) PF code.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:43 -07:00
Jack Morgenstein
afa8fd1db9 mlx4: Paravirtualize Node Guids for slaves
This is necessary in order to support > 1 VF/PF in a VM for software
that uses the node guid as a discriminator, such as librdmacm.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:43 -07:00
Jack Morgenstein
026149cbaa mlx4: Activate SR-IOV mode for IB
Remove the error returns for IB ports from mlx4_ib_add,
mlx4_INIT_PORT_wrapper, and mlx4_CLOSE_PORT_wrapper.

Currently, SRIOV is supported only for devices for which the
link layer is IB on all ports; RoCE support will be added later.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:42 -07:00
Jack Morgenstein
efcd235d73 net/mlx4_core: Adjustments to SET_PORT for IB SR-IOV
1. Slaves may not set the IS_SM capability for the port.
2. DEV_MGMT may not be set in multifunction mode.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:40 -07:00
Jack Morgenstein
993c401e20 mlx4_core: Add IB port-state machine and port mgmt event propagation
For an IB port, a slave should not show port active until that slave
has a valid alias-guid (provided by the subnet manager).  Therefore
the port-up event should be passed to a slave only after both the port
is up, and the slave's alias-guid has been set.

Also, provide the infrastructure for propagating port-management
events (client-reregister, etc) to slaves.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:37 -07:00
Jack Morgenstein
54679e1482 mlx4: Implement QP paravirtualization and maintain phys_pkey_cache for smp_snoop
This requires:

1. Replacing the paravirtualized P_Key index (inserted by the guest)
   with the real P_Key index.

2. For UD QPs, placing the guest's true source GID index in the
   address path structure mgid field, and setting the ud_force_mgid
   bit so that the mgid is taken from the QP context and not from the
   WQE when posting sends.

3. For UC and RC QPs, placing the guest's true source GID index in the
   address path structure mgid field.

4. For tunnel and proxy QPs, setting the Q_Key value reserved for that
   proxy/tunnel pair.

Since not all the above adjustments occur in all the QP transitions,
the QP transitions require separate wrapper functions.

Secondly, initialize the P_Key virtualization table to its default
values: Master virtualized table is 1-1 with the real P_Key table,
guest virtualized table has P_Key index 0 mapped to the real P_Key
index 0, and all the other P_Key indices mapped to the reserved
(invalid) P_Key at index 127.

Finally, add logic in smp_snoop for maintaining the phys_P_Key_cache.
and generating events on the master only if a P_Key actually changed.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:33 -07:00
Jack Morgenstein
fc06573dfa IB/mlx4: Initialize SR-IOV IB support for slaves in master context
Allocate SR-IOV paravirtualization resources and MAD demuxing contexts
on the master.

This has two parts.  The first part is to initialize the structures to
contain the contexts.  This is done at master startup time in
mlx4_ib_init_sriov().

The second part is to actually create the tunneling resources required
on the master to support a slave.  This is performed the master
detects that a slave has started up (MLX4_DEV_EVENT_SLAVE_INIT event
generated when a slave initializes its comm channel).

For the master, there is no such startup event, so it creates its own
tunneling resources when it starts up.  In addition, the master also
creates the real special QPs.  The ib_core layer on the master causes
creation of proxy special QPs, since the master is also
paravirtualized at the ib_core layer.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:32 -07:00
Jack Morgenstein
e2c76824ca mlx4_core: Add proxy and tunnel QPs to the reserved QP area
In addition, pass the proxy and tunnel QP numbers to slaves so the
driver can perform special QP paravirtualization.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:31 -07:00
Jack Morgenstein
1ffeb2eb8b IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support
1. Introduce the basic SR-IOV parvirtualization context objects for
   multiplexing and demultiplexing MADs.
2. Introduce support for the new proxy and tunnel QP types.

This patch introduces the objects required by the master for managing
QP paravirtualization for guests.

struct mlx4_ib_sriov is created by the master only.
It is a container for the following:

1. All the info required by the PPF to multiplex and de-multiplex MADs
   (including those from the PF). (struct mlx4_ib_demux_ctx demux)
2. All the info required to manage alias GUIDs (i.e., the GUID at
   index 0 that each guest perceives.  In fact, this is not the GUID
   which is actually at index 0, but is, in fact, the GUID which is at
   index[<VF number>] in the physical table.
3. structures which are used to manage CM paravirtualization
4. structures for managing the real special QPs when running in SR-IOV
   mode.  The real SQPs are controlled by the PPF in this case.  All
   SQPs created and controlled by the ib core layer are proxy SQP.

struct mlx4_ib_demux_ctx contains the information per port needed
to manage paravirtualization:

1. All multicast paravirt info
2. All tunnel-qp paravirt info for the port.
3. GUID-table and GUID-prefix for the port
4. work queues.

struct mlx4_ib_demux_pv_ctx contains all the info for managing the
paravirtualized QPs for one slave/port.

struct mlx4_ib_demux_pv_qp contains the info need to run an individual
QP (either tunnel qp or real SQP).

Note:  We made use of the 2 most significant bits in enum
mlx4_ib_qp_flags (based on enum ib_qp_create_flags in ib_verbs.h).
We need these bits in the low-level driver for internal purposes.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:30 -07:00
Hadar Hen Zion
7fb40f87c4 net/mlx4_core: Add security check / enforcement for flow steering rules set for VMs
Since VFs may be mapped to VMs which aren't trusted entities,  flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 12:55:59 -04:00
Hadar Hen Zion
a8edc3bf05 net/mlx4_core: Put Firmware flow steering structures in common header files
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 12:55:59 -04:00
Linus Torvalds
5dedb9f3bd InfiniBand/RDMA changes for the 3.6 merge window:
- Updates to the qib low-level driver
  - First chunk of changes for SR-IOV support for mlx4 IB
  - RDMA CM support for IPv6-only binding
  - Other misc cleanups and fixes
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABCAAGBQJQDXhUAAoJEENa44ZhAt0hZxwQAJydS9f9me31AGa45SAq8rA8
 6e3LgnQ6jS38he7LZZdSsT7g25jROCKOcTj6VUkNSVAVSkK8zcp7wngjDxw50IK6
 FF9hNeljMkWBflOhxzB34DRGCW4b4J+Yt1o7v1RtawiG/Mhri/6imKL0Aqjt4GwX
 a1MPZn+xI2osLujfdHJtATPWWB9jCaXdFe4DJUNPdqJhS6TN7s8OP3XMiqoJtdaV
 ptHeSSbjdUR1mg/h2LU2FVmWHXNSBxn7MEsrBBRkQVyiEkXieFBLwPTp4DqmAUJf
 xugm6Hf4sbiQ+QuU0baJODt56wveuYVQ4HKUzE0urUFXyU4TUB9blrehWZnKsRte
 wo/w4nvVlnXgGhHH0Igq76RDX8aCwc/6uQJ/29oChWjrei3HE0LjmIlPAu0vAhyw
 ViLe02/r2gKXQv1NxIqhPmGsJTZizg2mUk2eEJHHPQb/NGL7iNo6b+141AfURoqQ
 goGmlGdzffCRpmo6FXFZ57RPVRS4gwMunCY/Pmvq5a2t4oZh8899l2+V3N7bCfvH
 +JdavxAjia9U4IlgPsAqVaz8z8TyHOY/lEd75Wnw8q9www3kLx7hASvHsdwrS4LL
 ihzECzsaXOSoIXQzghs+6iyp1pzmzE9ve8OqbIGJStzlrOLyn7Gjo+Ixwm0SLsTO
 I7h9iJ1OMKFZ8bzmHsWb
 =f09j
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull InfiniBand/RDMA changes from Roland Dreier:
 - Updates to the qib low-level driver
 - First chunk of changes for SR-IOV support for mlx4 IB
 - RDMA CM support for IPv6-only binding
 - Other misc cleanups and fixes

Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c

* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
  IB/qib: checkpatch fixes
  IB/qib: Add congestion control agent implementation
  IB/qib: Reduce sdma_lock contention
  IB/qib: Fix an incorrect log message
  IB/qib: Fix QP RCU sparse warnings
  mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
  mlx4_core: Allow guests to have IB ports
  mlx4_core: Implement mechanism for reserved Q_Keys
  net/mlx4_core: Free ICM table in case of error
  IB/cm: Destroy idr as part of the module init error flow
  mlx4_core: Remove double function declarations
  IB/mlx4: Fill the masked_atomic_cap attribute in query device
  IB/mthca: Fill in sq_sig_type in query QP
  IB/mthca: Warning about event for non-existent QPs should show event type
  IB/qib: Fix sparse RCU warnings in qib_keys.c
  net/mlx4_core: Initialize IB port capabilities for all slaves
  mlx4: Use port management change event instead of smp_snoop
  IB/qib: RCU locking for MR validation
  IB/qib: Avoid returning EBUSY from MR deregister
  IB/qib: Fix UC MR refs for immediate operations
  ...
2012-07-24 13:56:26 -07:00
Amir Vadai
d9236c3f10 {NET,IB}/mlx4: Add rmap support to mlx4_assign_eq
Enable callers of mlx4_assign_eq to supply a pointer to cpu_rmap.
If supplied, the assigned IRQ is tracked using rmap infrastructure.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-19 08:34:37 -07:00
Amir Vadai
af22d9de45 net/mlx4: Move MAC_MASK to a common place
Define this macro is one common place instead of duplicating it over the code

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-19 08:34:37 -07:00
Jack Morgenstein
6634961c14 mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.

In addition, in SR-IOV mode, do the following:

1. Reduce reported P_Key table size by 1.
   This is done to reserve the highest P_Key index for internal use,
   for declaring an invalid P_Key in P_Key paravirtualization.
   We require a P_Key index which always contain an invalid P_Key
   value for this purpose (i.e., one which cannot be modified by
   the subnet manager).  The way to do this is to reduce the
   P_Key table size reported to the subnet manager by 1, so that
   it will not attempt to access the P_Key at index #127.

2. Paravirtualize the GID table size to 1. Thus, each guest sees
   only a single GID (at its paravirtualized index 0).

In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-07-11 11:52:23 -07:00
Jack Morgenstein
396f2feb05 mlx4_core: Implement mechanism for reserved Q_Keys
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests.  These proxy QPs
send their packets to a "tunnel" QP owned by the master.  The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.

For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key.  These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.

This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.

The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.

In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.

The QPNs for these QPs are arranged as follows:
 1. The real SQP numbers (8)
 2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
 3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)

To support these QPs, two new fields are added to struct mlx4_dev:

  base_sqp:  this is the QP number of the first of the real SQPs
  base_tunnel_sqp: this is the qp number of the first qp in the tunnel
                   sqp region. (On guests, this is the first tunnel
                   sqp of the 8 which are assigned to that guest).

In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region.  (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)

Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-07-11 11:35:55 -07:00
Jack Morgenstein
2aca1172c2 net/mlx4_core: Initialize IB port capabilities for all slaves
With IB SR-IOV, each slave has its own separate copy of the port
capabilities flags.  For example, the master can run a subnet manager
(which causes the IsSM bit to be set in the master's port
capabilities) without affecting the port capabilities seen by the
slaves (the IsSM bit will be seen as cleared in the slaves).

Also add a static inline mlx4_master_func_num() to enhance readability
of the code.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-07-10 09:57:06 -07:00
Jack Morgenstein
00f5ce99dc mlx4: Use port management change event instead of smp_snoop
The port management change event can replace smp_snoop.  If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command).  In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.

If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).

In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events.  The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).

Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.

We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-07-10 09:47:10 -07:00
Jack Morgenstein
752a50cab6 mlx4_core: Pass an invalid PCI id number to VFs
Currently, VFs have 0 in their dev->caps.function field.  This is a
valid pci id (usually of the PF).  Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-07-08 18:05:05 -07:00
Hadar Hen Zion
592e49dda8 net/mlx4: Implement promiscuous mode with device managed flow-steering
The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07 16:23:06 -07:00
Hadar Hen Zion
0ff1fb654b {NET, IB}/mlx4: Add device managed flow steering firmware API
The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07 16:23:05 -07:00
Hadar Hen Zion
8fcfb4db74 net/mlx4_core: Add firmware commands to support device managed flow steering
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07 16:23:05 -07:00
Hadar Hen Zion
c96d97f4d1 net/mlx4: Set steering mode according to device capabilities
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07 16:23:05 -07:00
Marcel Apfelbaum
3fc929e2d6 net/mlx4_core: Fix number of EQs used in ICM initialisation
In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.

To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
   capabilities.  The PPF uses the phys capabilities when it computes things
   like ICM size.

   The dev_caps structure will then contain the paravirtualized values, making
   bookkeeping much easier in SRIOV mode. We add a structure rather than a
   single parameter because there will be other fields in the phys_caps.

   The first field we add to the mlx4_phys_caps structure is num_phys_eqs.

2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
   passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
   has this number of EQs available.

   However, the total number of EQs which must be allowed for in the ICM is
   (1 << log_num_eqs) * (#VFs + #PFs).  Rather than compute this quantity,
   we allocate ICM space for 1024 EQs (which is the device maximum
   number of EQs, and which is the value we place in the mlx4_phys_caps structure).

   For INIT_HCA, however, we use the per-function number of EQs as described
   above.

Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-31 18:18:16 -04:00
Linus Torvalds
c23ddf7857 InfiniBand/RDMA changes for the 3.5 merge window:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
  - Add generic and mlx4 support for "raw" QPs: allow suitably privileged
    applications to send and receive arbitrary packets directly to/from
    the hardware
  - Add "doorbell drop" handling to the cxgb4 driver
  - A fairly large batch of qib hardware driver changes
  - A few fixes for lockdep-detected issues
  - A few other miscellaneous fixes and cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABCAAGBQJPumbZAAoJEENa44ZhAt0h8LgP/0fXe7Szm3n6P6UvMAVqkagM
 4PpreH3mpWUFpzqeQE1JPDtgx700R6aPipbHqgIN+k61RWMpLjICGcNx7iwxn1I+
 zqdquGygWgjceLz+BLVlk+iBmJt3vZ3fPRAXc7fdP+jhIarWkNIOy1pXWTUuRvED
 jL8jIaxhCcgAVzm/zNyt6IPxkaHvCz7K9wqmpyU0dsO9OyPdGvWA9+CkGXwmOCPq
 mxSVhWnfGsMkPBsL7EgTC5KP/ox2PKq6rFgysmVVS+rKCpP0L8BEVQyGX3Gf8KA8
 yV+KdTi9ofDnFrv6R7Wz0v7HRUih8GRssakzBu7Y7HLfK1M/QwMG0GUAibXGZObc
 vUXuQ3uRJ/cIzMPXqKeGYwpb5t+TmxyjhWu44OjCUQkNau91+9BSbA69S88KXc49
 aTJiCZlhPuGf4uGMWJJuPLcE2xO2QCZj+8ckL2STYrIip6GWlCH02kJaQmRkuWH2
 UhMOeJDBC4nvh4EQT/WwHpGzyhkavE2ayfo5YemxBJXo+P5Mdbf7WIDRQDLUEeQH
 F8sPoccH4hDiAorN/SkTsm14jVTP7oWW1M40Ont59Nhbgm88MsVkvjoneHnfBvbD
 HjK92soCWnYTAoREfj0G4xUxZgMdOZcezWrX0rx5LJ8Ju9y4zAi3cKGr7lg6hs4X
 syKfN0VjiDRtJ+pxayi3
 =yWfr
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull InfiniBand/RDMA changes from Roland Dreier:
 - Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
 - Add generic and mlx4 support for "raw" QPs: allow suitably privileged
   applications to send and receive arbitrary packets directly to/from
   the hardware
 - Add "doorbell drop" handling to the cxgb4 driver
 - A fairly large batch of qib hardware driver changes
 - A few fixes for lockdep-detected issues
 - A few other miscellaneous fixes and cleanups

Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.

* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
  RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
  IB/mlx4: Fix mlx4_ib_add() error flow
  IB/core: Fix IB_SA_COMP_MASK macro
  IB/iser: Fix error flow in iser ep connection establishment
  IB/mlx4: Increase the number of vectors (EQs) available for ULPs
  RDMA/cxgb4: Add query_qp support
  RDMA/cxgb4: Remove kfifo usage
  RDMA/cxgb4: Use vmalloc() for debugfs QP dump
  RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
  RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
  RDMA/cxgb4: Add DB Overflow Avoidance
  RDMA/cxgb4: Add debugfs RDMA memory stats
  cxgb4: DB Drop Recovery for RDMA and LLD queues
  cxgb4: Common platform specific changes for DB Drop Recovery
  cxgb4: Detect DB FULL events and notify RDMA ULD
  RDMA/cxgb4: Drop peer_abort when no endpoint found
  RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
  mlx4_core: Change bitmap allocator to work in round-robin fashion
  RDMA/nes: Don't call event handler if pointer is NULL
  RDMA/nes: Fix for the ORD value of the connecting peer
  ...
2012-05-21 17:54:55 -07:00
Shlomo Pongratz
b3416f4476 mlx4_core: Add second capabilities flags field
This patch adds a 64-bit flags2 features member to struct mlx4_dev to
export further features of the hardware.  The original flags field
tracks features whose support bits are advertised by the firmware in
offsets 0x40 and 0x44 of the query device capabilities command.
flags2 will track features whose support bits are scattered at various
offsets.

RSS support is the first feature to be exported through flags2.  RSS
capabilities are located at offset 0x2e.  The size of the RSS
indirection table is also given in this offset.

Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-05-08 11:54:32 -07:00
Oren Duer
c0c1d3d761 IB/mlx4: Put priority bits in WQE of IBoE MLX QP
Otherwise CM packets going over MLX QP1 get fixed scheduling priority 0.
We want CM packets to get the same scheduling priority, and therefore
map to the same SQ (Schedule Queue) and eventually TC (Traffic Class),
as the application requested for the actual QP used for the connection.

Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-05-08 11:48:09 -07:00
Amir Vadai
e5395e92a4 net/mlx4_core: set port QoS attributes
Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-05 05:08:03 -04:00
Amir Vadai
0e98b523c4 net/mlx4_en: Force user priority by QP attribute
Instead of relying on HW to change schedule queue by UP, schedule
queue is fixed for a tx_ring, and UP in WQE is ignored in this aspect.  This
resolves two issues with untagged traffic:
1. untagged traffic has no UP in packet which is needed for QoS. The change
   above allows setting the schedule queue (and by that the UP) of such a stream.
2. BlueFlame uses the same field used by vlan tag. So forcing UP from QPC
   allows using BF for untagged but prioritized traffic.

In old firmware that force UP is not supported, untagged traffic will not subject to
QoS.

Because UP is set by QP, need to always have a tx ring per UP, even if pfcrx
module paramter is false.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-05 05:08:03 -04:00
Linus Torvalds
250f6715a4 The following text was taken from the original review request:
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
 		https://lkml.org/lkml/2012/3/4/159
 --
 
 Nearly every subsystem has some kind of header with a proto like:
 
 	void foo(struct device *dev);
 
 and yet there is no reason for most of these guys to care about the
 sub fields within the device struct.  This allows us to significantly
 reduce the scope of headers including headers.  For this instance, a
 reduction of about 40% is achieved by replacing the include with the
 simple fact that the device is some kind of a struct.
 
 Unlike the much larger module.h cleanup, this one is simply two
 commits.  One to fix the implicit <linux/device.h> users, and then
 one to delete the device.h includes from the linux/include/ dir
 wherever possible.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPbNxLAAoJEOvOhAQsB9HWR6QQAMRUZ94O2069/nW9h4TO/xTr
 Hq/80lo/TBBiRmob3iWBP76lzgeeMPPVEX1I6N7YYlhL3IL7HsaJH1DvpIPPHXQP
 GFKcBsZ5ZLV8c4CBDSr+/HFNdhXc0bw0awBjBvR7gAsWuZpNFn4WbhizJi4vWAoE
 4ydhPu55G1G8TkBtYLJQ8xavxsmiNBSDhd2i+0vn6EVpgmXynjOMG8qXyaS97Jvg
 pZLwnN5Wu21coj6+xH3QUKCl1mJ+KGyamWX5gFBVIfsDB3k5H4neijVm7t1en4b0
 cWxmXeR/JE3VLEl/17yN2dodD8qw1QzmTWzz1vmwJl2zK+rRRAByBrL0DP7QCwCZ
 ppeJbdhkMBwqjtknwrmMwsuAzUdJd79GXA+6Vm+xSEkr6FEPK1M0kGbvaqV9Usgd
 ohMewewbO6ddgR9eF7Kw2FAwo0hwkPNEplXIym9rZzFG1h+T0STGSHvkn7LV765E
 ul1FapSV3GCxEVRwWTwD28FLU2+0zlkOZ5sxXwNPTT96cNmW+R7TGuslZKNaMNjX
 q7eBZxo8DtVt/jqJTntR8bs8052c8g1Ac1IKmlW8VSmFwT1M6VBGRn1/JWAhuUgv
 dBK/FF+I1GJTAJWIhaFcKXLHvmV9uhS6JaIhLMDOetoOkpqSptJ42hDG+89WkFRk
 o55GQ5TFdoOpqxVzGbvE
 =3j4+
 -----END PGP SIGNATURE-----

Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux

Pull <linux/device.h> avoidance patches from Paul Gortmaker:
 "Nearly every subsystem has some kind of header with a proto like:

	void foo(struct device *dev);

  and yet there is no reason for most of these guys to care about the
  sub fields within the device struct.  This allows us to significantly
  reduce the scope of headers including headers.  For this instance, a
  reduction of about 40% is achieved by replacing the include with the
  simple fact that the device is some kind of a struct.

  Unlike the much larger module.h cleanup, this one is simply two
  commits.  One to fix the implicit <linux/device.h> users, and then one
  to delete the device.h includes from the linux/include/ dir wherever
  possible."

* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  device.h: audit and cleanup users in main include dir
  device.h: cleanup users outside of linux/include (C files)
2012-03-24 10:41:37 -07:00
Linus Torvalds
0c2fe82a9b InfiniBand/RDMA changes for the 3.4 merge window. Nothing big really
stands out; by patch count lots of fixes to the mlx4 driver plus some
 cleanups and fixes to the core and other drivers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABCAAGBQJPZ2THAAoJEENa44ZhAt0hMgkP/AwXjwzz6lYlIizytQ5KOH11
 CT/VoHLIGIwY31aRhZRHggWLEbJi8akgfh04K9PiSh/muFRPYk5KJDoQEoJV5Odv
 12krqtpZeL41YcAPq0wiyP3Ki5AZDCDumzWbOtmxE9m93mVfi3yFTTWDHFo/7SOx
 A2kUITdKuZhgBpCFYS23Gs8QTWcMPUlwNlM76edG90BjSySHsK15tbqTUaEOC6Ux
 SPG0p0c2YjlZCPmRObrCL65o5LFRVajinZ4rXN7rre4LEU+IuXgW+mQU2Kwy8z6a
 oMPE2l4OMSqj270r2PlVK087gGH69nKfLgLQLJiP0Id+KwdYUk7vQcA+Fu0jwjP3
 Ci/ahllvB76IiaNbax0vTy2ohCJmilLLotAP46NW0vPR2/KnmVy0Mqk8pXQQddw4
 tnAFNnafn/MjTty8GwqyXR/enJZs29ePcSxcYnKjXYRIgG4ldejL2wktgSra8+gb
 3/qFag1HRgZzcICkXGpHj7uWJ2KDe++1m6KTb0THUmrjuiel6ATFZpYoeRed3GfS
 ZMqpjZvuXM8nA9CrKMkzm5vIiUFF8Qq0hUTLR38F8FiNEhmC08JqH5PqjJ3Z18if
 R1yG4W4xmp/0ICHg4zyg6LWV3YsweDD+jSCJpW+KNBvu3HtYb41HIlK+i2TTmtPD
 3etEZZRwROAyYKcwN01p
 =DbLx
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
 "Nothing big really stands out; by patch count lots of fixes to the
  mlx4 driver plus some cleanups and fixes to the core and other
  drivers."

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
  mlx4_core: Scale size of MTT table with system RAM
  mlx4_core: Allow dynamic MTU configuration for IB ports
  IB/mlx4: Fix info returned when querying IBoE ports
  IB/mlx4: Fix possible missed completion event
  mlx4_core: Report thermal error events
  mlx4_core: Fix one more static exported function
  IB: Change CQE "csum_ok" field to a bit flag
  RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
  RDMA/cxgb3: Don't pass irq flags to flush_qp()
  mlx4_core: Get rid of redundant ext_port_cap flags
  RDMA/ucma: Fix AB-BA deadlock
  IB/ehca: Fix ilog2() compile failure
  IB: Use central enum for speed instead of hard-coded values
  IB/iser: Post initial receive buffers before sending the final login request
  IB/iser: Free IB connection resources in the proper place
  IB/srp: Consolidate repetitive sysfs code
  IB/srp: Use pr_fmt() and pr_err()/pr_warn()
  IB/core: Fix SDR rates in sysfs
  mlx4: Enforce device max FMR maps in FMR alloc
  IB/mlx4: Set bad_wr for invalid send opcode
  ...
2012-03-21 10:33:42 -07:00
Paul Gortmaker
313162d0b8 device.h: audit and cleanup users in main include dir
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.

Clean up the users as follows:

1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.

2) For headers not really using anything from device.h, simply
delete the include altogether.

3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h

4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).

Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.

Total removals from #1 and #2: 51.  Total additions coming
from #3: 9.  Total other implicit dependencies from #4: 7.

As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-03-16 10:38:24 -04:00
Roland Dreier
42872c7a5e Merge branches 'misc' and 'mlx4' into for-next
Conflicts:
	drivers/infiniband/hw/mlx4/main.c
	drivers/net/ethernet/mellanox/mlx4/main.c
	include/linux/mlx4/device.h
2012-03-12 16:25:28 -07:00
Or Gerlitz
096335b3f9 mlx4_core: Allow dynamic MTU configuration for IB ports
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB).  Allow for dynamic mtu
configuration through a new, per-port sysfs entry.

Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.

For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode.  To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-03-12 16:24:59 -07:00
Jack Morgenstein
5984be9004 mlx4_core: Report thermal error events
Print an error message when a thermal error async event is reported by the HW.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-03-12 16:24:59 -07:00
Or Gerlitz
8154c07fe1 mlx4_core: Get rid of redundant ext_port_cap flags
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).

This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-03-06 17:25:18 -08:00
Yevgeny Petrilin
9a9a232a92 net/mlx4: fixing sparse warnings for not declared, functions
The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 15:19:18 -05:00
Eric Dumazet
6221217199 mlx4_en: dont change mac_header on xmit
A driver xmit function is not allowed to change skb without special
care.

mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.

This removes a dumb test : if (ethh && ethh->h_dest)

Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26 14:22:05 -05:00
Eli Cohen
a5bbe892da mlx4: Enforce device max FMR maps in FMR alloc
ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt.  The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.

Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-02-26 01:43:37 -08:00
Eugenia Emantayev
93ece0c1a7 mlx4_en: eth statistics modification
In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22 15:08:43 -05:00
Yevgeny Petrilin
8d0fc7b611 mlx4_core: Changing link sensing logic
New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19 14:57:07 -05:00
Yevgeny Petrilin
58a60168d1 mlx4: capability for link sensing
For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19 14:57:06 -05:00
Jack Morgenstein
ab9c17a009 mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet
1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13 13:56:08 -05:00
Marcel Apfelbaum
2b8fb2867c mlx4_core: mtts resources units changed to offset
In the previous implementation mtts are managed by:
1. order     - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order     - log(mtts) rather than segments
2. offset    - mtt index in mtt table

Note: The actual mtt allocation is made in segments but it is
      transparent to callers.

Rational: The mtt resource holders are not interested on how the allocation
          of mtt is done, but rather on how they will use it.

Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13 13:56:07 -05:00
Eugenia Emantayev
ffe455ad04 mlx4: Ethernet port management modifications
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware

Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13 13:56:07 -05:00
Jack Morgenstein
f5311ac109 mlx4_core: Reduce number of PD bits to 17
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.

Change the allocator to return only 17 bits for the PD.  The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13 13:56:05 -05:00