The Huawei D06 board (and variants) can support Quad mode of operation.
Since we have no current method in ACPI SPI bus device resource description
to describe this information, use DMI to detect the board, and set the
controller buswidth override bits.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-4-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CMD_CONFIG register memory interface type field is not set configured
for Dual and Quad modes, so set appropriately.
This was not detected previously as we only ever operated in standard SPI
mode.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently ACPI firmware description for a SPI device does not have any
method to describe the data buswidth on the board.
So even through the controller and device may support higher modes than
standard SPI, it cannot be assumed that the board does - as such, that
device is limited to standard SPI in such a circumstance.
As a workaround, allow the controller driver supply buswidth override bits,
which are used inform the core code that the controller driver knows the
buswidth supported on that board for that device.
A host controller driver might know this info from DMI tables, for example.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-2-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 0e6aae08e9 ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200228155437.1558219-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change broke userspace applications which issue an SPI_IOC_WR_MODE
ioctl() to an spidev: Chip Select polarity will be incorrect unless the
application is changed to set SPI_CS_HIGH. And once changed, it will be
incompatible with kernels not containing the commit.
Fix by setting SPI_CS_HIGH in spidev_ioctl() (under the same conditions
as in of_spi_parse_dt()).
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/fca3ba7cdc930cd36854666ceac4fbcf01b89028.1582027457.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v5.1+
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
All RSPI variants support selecting the word order.
Advertize support for LSB-first order, and act upon the flag being set.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218105810.902-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Basic SPI features like clock phase/polarity and loopback mode are
common to all RSPI variants. Factor them out to reduce duplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218105810.902-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Add a SPI device driver that sits in-band and provides a SPI controller
which supports chip selects via a mux-control. This enables extra SPI
devices to be connected with limited native chip selects.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200204032838.20739-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for SPI controller found in Qualcomm Atheros
AR934x/QCA95xx SoCs.
This controller is a superset of the already supported qca,ar7100-spi.
Besides the bit-bang mode in spi-ath79.c, this new controller added
a new "shift register" mode, allowing faster spi operations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200210034152.49063-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver doesn't call any DT functions like of_get_property(). Remove
the of.h include as it isn't used.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes stm32 QSPI driver to defer its probe operation when a reset
controller device have not yet probed but is registered in the
system.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200203135048.1299-2-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On AM654, McSPI can only support 4K - 1 bytes per transfer when DMA is
enabled. Therefore populate master->max_transfer_size callback to
inform client drivers of this restriction when DMA channels are
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 84d043185d ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Improving spi 8 bit per word mode transfer performance
by using 16 bit per word transfer and receive when the data
length is even and larger than one.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200115162301.235926-3-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-ti-qspi.c: In function ‘ti_qspi_start_transfer_one’:
drivers/spi/spi-ti-qspi.c:392:8: warning: ‘rx_wlen’ may be used uninitialized in this function [-Wmaybe-uninitialized]
392 | if (rx_wlen >= 32)
| ^
drivers/spi/spi-ti-qspi.c:318:12: note: ‘rx_wlen’ was declared here
318 | u8 rxlen, rx_wlen;
| ^~~~~~~
The warning is a false positive; it is not thrown by all compiler versions, e.g.
Red Hat Cross 9.2.1-1 but not Linaro GCC 7.5-2019.12.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Link: https://lore.kernel.org/r/20200115100700.3357-1-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing NPCM BMC Peripheral SPI controller 16 bit
send and receive support by writing and reading
the SPI data in the right order.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200115162301.235926-2-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Intel Comet Lake PCH-V which has the same LPSS than on
Intel Kaby lake unlike other Intel Comet Lake PCH variants that are based
on Intel Cannon Lake PCH LPSS.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200116091035.575175-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a4025995 ("spi: lpspi: use the core way to implement cs-gpio function")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Optimize the 8-bit based transfers, as used by the SPI flash
devices, by reading the data registers by 32 and 128 bits when
possible and copy the contents to the receive buffer.
The speed improvement is 4.9x using quad read.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20200114124125.361429-3-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI QSPI IP has limitations:
- the MMIO region is 64MB in size
- in non-MMIO mode, the transfer can handle 4096 words max.
Add support for bigger devices.
Use MMIO and DMA transfers below the 64MB boundary, use
software generated transfers above.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20200114124125.361429-2-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currrently the memory for the clk_bulk_data of the QSPI controller
is allocated with spi_alloc_master(). The bulk data pointer is passed
to devm_clk_bulk_get() which saves it in clk_bulk_devres->clks. When
the device is removed later devm_clk_bulk_release() is called and
uses the bulk data referenced by the pointer to release the clocks.
For this driver this results in accessing memory that has already
been freed, since the memory allocated with spi_alloc_master() is
released by spi_controller_release(), which is called before the
managed resources are released.
Use device managed memory for the clock bulk data to fix the issue
described above.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200108133948.1.I35ceb4db3ad8cfab78f7cd51494aeff4891339f5@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the driver for the HiSilicon v3xx SPI NOR flash controller, commonly
found in hi16xx chipsets.
This is a different controller than that in drivers/mtd/spi-nor/hisi-sfc.c;
indeed, the naming for that driver is poor, since it is really known as
FMC, and can support other memory technologies.
The driver module name is "hisi-sfc-v3xx", as recommended by HW designer,
being an attempt to provide a distinct name - v3xx being the unique
controller versioning.
Only ACPI firmware is supported.
DMA is not supported, and we just use polling mode for operation
completion notification.
The driver uses the SPI MEM OPs.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575900490-74467-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "RevPi Connect Flat" PLC offered by KUNBUS has 4 slaves attached
to the BCM2835 SPI master. Raise the maximum number of slaves in the
driver accordingly.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/01453fd062de2d49bd74a847e13a0781cbf8143d.1578572268.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
STR is a well-known stringify macro so it should be avoided in drivers
to avoid warnings like this (MIPS architecture while compile testing):
drivers/spi/spi-sh-msiof.c:76:0: warning: "STR" redefined
#define STR 0x40 /* Status Register */
arch/mips/include/asm/mipsregs.h:30:0: note: this is the location of the previous definition
#define STR(x) __STR(x)
To maintain consistency between all register names add a SI prefix to
all of them. This also matches register names in datasheet.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200108194319.3171-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for GPIO chip selects using GPIO descriptors. As the RSPI
controller always drives a native chip select when performing a
transfer, at least one native chip select must be left unused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-7-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
RSPI variants on some SuperH or R-Mobile SoCs support multiple native
chip selects. Add support for this by configuring the SSL Assert Signal
Setting.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-6-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_config_register() macro is used in a single place.
Make the code easier to read by just removing it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-5-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the MSIOF SPI driver uses custom code to handle the unused
native chip select with GPIO chip selects.
Convert the driver to use the new generic handling in the SPI core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI master controllers always drive a native chip select when
performing a transfer. Hence when using both native and GPIO chip
selects, at least one native chip select must be left unused, to be
driven when performing transfers with slave devices using GPIO chip
selects.
Currently, to find an unused native chip select, SPI controller drivers
need to parse and process cs-gpios theirselves. This is not only
duplicated in each driver that needs it, but also duplicates part of the
work done later at SPI controller registration time. Note that this
cannot be done after spi_register_controller() returns, as at that time,
slave devices may have been probed already.
Hence add generic support to the SPI subsystem for finding an unused
native chip select. Optionally, this unused native chip select, and all
other in-use native chip selects, can be validated against the maximum
number of native chip selects available on the controller hardware.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Use platform_get_irq_byname_optional() instead of platform_get_irq_byname()
to avoid below error message during probe:
[3.265115] bcm_iproc 68c70200.spi: IRQ spi_lr_fullness_reached not found
[3.272121] bcm_iproc 68c70200.spi: IRQ spi_lr_session_aborted not found
[3.284965] bcm_iproc 68c70200.spi: IRQ spi_lr_impatient not found
[3.291344] bcm_iproc 68c70200.spi: IRQ spi_lr_session_done not found
[3.297992] bcm_iproc 68c70200.spi: IRQ mspi_done not found
[3.303742] bcm_iproc 68c70200.spi: IRQ mspi_halted not found
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200107040912.16426-1-rayagonda.kokatanur@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4TMdwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0M5UB/9w0mzrmuaJzctm3Jm8LiCIjJoZ0woQ
chgbhm2C/I6idENxdUhaJ1YZMI6NkmJKpJy5tQ/QH4MnbOVT/vHIEmIsRYO0vYoF
ApERJLia8da1OpiJlPTbsg3eUXVNmPMVeAkq5MgKSflaIjV6Ejc0FRWmgDYvzhu9
xkCsptAF7MYPUuHdBcjXPscSf1/w+FdDy8VYncEluyJ0NpGDU64N/XdTwRmsG8QW
BxA1jPPKi445NsC+OV8SFfNZbeEXG2iSEBPvp4tMGtd0TiIp3UNLTRzMstEFE6SD
hCzL9fQEzUgHD+B0vLmccyy0HR0phk6813jf9KeToAjAxKtf5XhQajW+
=Ad4n
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
dw_spi_irq() and dw_spi_transfer_one concurrent calls.
I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null,
dw->len==4, and dw->tx_end==1.
When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one
may concurrent visit dw_spi, so I think dw_spi structure lack of protection.
Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq,
store dw rx/tx instructions and other cores handle irq load dw rx/tx
instructions may out of order.
[ 1025.321302] Call trace:
...
[ 1025.321319] __crash_kexec+0x98/0x148
[ 1025.321323] panic+0x17c/0x314
[ 1025.321329] die+0x29c/0x2e8
[ 1025.321334] die_kernel_fault+0x68/0x78
[ 1025.321337] __do_kernel_fault+0x90/0xb0
[ 1025.321346] do_page_fault+0x88/0x500
[ 1025.321347] do_translation_fault+0xa8/0xb8
[ 1025.321349] do_mem_abort+0x68/0x118
[ 1025.321351] el1_da+0x20/0x8c
[ 1025.321362] dw_writer+0xc8/0xd0
[ 1025.321364] interrupt_transfer+0x60/0x110
[ 1025.321365] dw_spi_irq+0x48/0x70
...
Signed-off-by: wuxu.wu <wuxu.wu@huawei.com>
Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The API for PTP system timestamping (associating a SPI transaction with
the system time at which it was transferred) is flawed: it assumes that
the xfer->tx_buf pointer will always be present.
This is, of course, not always the case.
So introduce a "progress" variable that denotes how many word have been
transferred.
Fix the Freescale DSPI driver, the only user of the API so far, in the
same patch.
Fixes: b42faeee71 ("spi: Add a PTP system timestamp to the transfer structure")
Fixes: d6b71dfaee ("spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012417.1057-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We can catch whether the SPI controller has declared it can take care of
software timestamping transfers, but didn't. So do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012444.1204-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the OC Tiny driver over to handling CS GPIOs using
GPIO descriptors in the core.
This driver is entirely relying on GPIOs to be used for
chipselect, so let the core pick these out using either
device tree or machine descriptors.
There are no in-tree users of this driver so no board files
need to be patched, out-of-tree boardfiles can use machine
descriptor tables, c.f. commit 1dfbf334f1.
Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205092411.64341-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds DMA transfer mode support for UniPhier SPI controller.
Since this controller requires simulteaneous transmission and reception,
this indicates SPI_CONTROLLER_MUST_RX and SPI_CONTROLLER_MUST_TX.
Because the supported dma controller has alignment restiction,
there is also a restriction that 'maxburst' parameters in dma_slave_config
corresponds to one word width.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-6-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-tegra114.c:272:2-17: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-tegra114.c:275:2-17: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-4-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-imx.c:1233:2-17: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-imx.c:1235:2-17: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-fsl-lpspi.c:472:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-fsl-lpspi.c:474:2-19: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This changes each argument of functions uniphier_irq_{enable,disable}()
to uniphier_spi_priv because these functions are used not only for
spi_device but also for the entire controller.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab8170 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an incremental
fix for build errors introduced on SPARC by the earlier fix for error
handling in probe in that driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34xt8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D64B/91GGhGgNybvExhls79YKQx9STnv8Vl
sIVgbnVxnTHrAa+s/5ML0T8LzH9W5KcBUuL+KCd0oMdaE9QZSCKGdraEqDJz7Ie4
iHbBSAtwL0tegbyM+J4oKC3wen3Lg1u1iwn4Plo2fVKEah7zG6gdneQcf454EnEF
om2Sj2K7tqoqN1jIl0j/FGQtlDXvhzp3m+CyGakjzsBvINmSGixrO5Lit/dx3qSf
xkhLDWZqUk3UatusPXhpJJVxWPuVvT5NQkvUYDte1rHxrVdolYQctwBRPN/uZ2hq
FcLzUbWVFx7p3cDqvuQ6XTptpue4njnaPOT/LW6tud4BexlaV1q83XYs
=gPXn
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an
incremental fix for build errors introduced on SPARC by the earlier
fix for error handling in probe in that driver"
* tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl: use platform_get_irq() instead of of_irq_to_resource()
spi: nxp-fspi: Ensure width is respected in spi-mem operations
spi: spi-ti-qspi: Fix a bug when accessing non default CS
spi: fsl: don't map irq during probe
spi: spi-cavium-thunderx: Add missing pci_release_regions()
spi: sprd: Fix the incorrect SPI register
gpiolib: of: Make of_gpio_spi_cs_get_count static
spi: fsl: Handle the single hardwired chipselect case
gpio: Handle counting of Freescale chipselects
spi: fsl: Fix GPIO descriptor support
spi: dw: Correct handling of native chipselect
spi: cadence: Correct handling of native chipselect
spi: pxa2xx: Add support for Intel Jasper Lake
Use dev_dbg() on -EPROBE_DEFER and dev_err() on all
other errors.
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191216230802.45715-2-jquinlan@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fclk and its rate are retrieved from DT.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20191211193954.747745-2-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of grabbing GPIOs using the legacy interface and
handling them in the setup callback, just let the core
grab and use the GPIOs using descriptors.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20191205083915.27650-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-8-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-6-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA channel was not released if either devm_request_irq() or
devm_spi_register_controller() failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191212135550.4634-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533e ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commits 05104c266a ("ARM: shmobile: r7s72100: genmai: Remove
legacy board file") and a483dcbfa2 ("ARM: shmobile: lager: Remove
legacy board support", RZ/A1 and R-Car Gen2 SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
match platform devices by name anymore for these platforms, hence remove
the corresponding platform_device_id entries.
The platform_device_id entry for "rspi" is retained, as it is used by
the SH7757 platform, which hasn't been converted to DT yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20191211131553.23960-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
If dws is NULL in dw_spi_host_add(), we return the error to the
upper callers instead of crashing. The patch replaces BUG_ON by
returning -EINVAL to the caller.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lore.kernel.org/r/20191205231421.9333-1-pakki001@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ->chipselect() callback on the bit-banged SPI library
master is optional if using GPIO descriptors: when using
descriptors exclusively without any native chipselects,
the core does not even call out the the native ->set_cs()
and therefore ->chipselect() on a bit-banged SPI master
will not even be called in this case.
Make sure to respect the SPI_MASTER_GPIO_SS as used by
e.g. spi-gpio.c though: this setting will make the core
handle the chip select using GPIO descriptors *AND* call
the local chipselect handler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205091340.59850-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This switches the STM32 SPI driver over to using GPIO
descriptors for chip select. Instead of the callbacks for
picking the GPIO lines using the legacy API we just let
the core handle it all using descriptors.
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205083401.27077-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reverts commit 6e0a32d6f3 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd876 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407f ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no reason to use the dma_request_slave_channel_compat() as no
filter function and parameter is provided.
Switch the driver to use dma_request_chan() instead and add support for
deferred probing against DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191121092703.30465-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_spi_cpm_free() function does not make the same
checks as the error path in fsl_spi_cpm_init() leading
to crashes on error.
Cc: Fabio Estevam <festevam@gmail.com>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113014442.12100-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit d948e6ca18 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.
This causes SPI devices to return errors for cases where they do:
ret = spi_setup(spi);
if (ret)
return ret;
As in many cases the SPI devices do not check for if (ret < 0).
Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.
Fixes: d948e6ca18 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to
Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_LOOP is set in spi->mode but not propagated to the register.
A previous patch removed the bit during a cleanup.
Fixes: e1bc204894 ("spi: dw: fix potential variable assignment error")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Link: https://lore.kernel.org/r/1572985330-5525-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to disable and unprepare clk when probe fails and
remove.
Add the calls to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Link: https://lore.kernel.org/r/20191101121745.13413-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Committed version of the commit b9fc2d207e ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.
Complete the code move by doing those changes now.
Fixes: b9fc2d207e ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if the flag use_gpio_descriptors is set, it is possible that
cs_gpiods was not allocated, which leads to a kernel crash.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191024141309.22434-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_ioremap_resource() has already a check for resource pointer
being NULL. No need to double check this.
Drop extra check of platform_get_resource() returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel(R) Programmable Services Engine (Intel(R) PSE) SPI controllers in
Intel Elkhart Lake have two Chip Select signals instead of one.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-3-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement pm_runtime hooks at pci driver.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
[jarkko.nikula@linux.intel.com: Forward ported on top of
commit 1e69598325 ("spi: dw: Add basic runtime PM support")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-2-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit 1e69598325 ("spi: dw: Add basic runtime PM support")
there is following warning from PCI enumerated DesignWare SPI controller
during probe:
dw_spi_pci 0000:00:13.0: Unbalanced pm_runtime_enable!
Runtime PM is already enabled for PCI devices by the PCI core and doing
it again in common DW SPI code leads to unbalanced enable calls.
Fix this by moving the runtime PM enable/disable calls to the platform
driver part of the driver.
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20191018132131.31608-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a4 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Thanks to the recent change in this driver, it is now possible to
prevent using the CS0 with GPIO during setup. It then allows to remove
the special handling of this case in the cs_activate() and
cs_deactivate() functions.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-8-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the previous implementation of this driver, the index of the GPIO
used as CS was linked to the offset of the CS register used to
configure the transfer.
With this new implementation the first CS register not used by
internal CS is associated to all the GPIO CS. It allows to not be
anymore limited to have only 4 CS managed, now it is possible to have
in the same time until 3 internal CS and no more limit for the CS
GPIO.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-7-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the conversion to GPIO descriptor, the GPIO used as chip select,
can be directly access from the spi_device struct. So there is no need
to keep the field npcs_pin.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-5-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As platform_get_irq_byname() now prints an error when the interrupt
does not exist, scary warnings may be printed for optional interrupts:
renesas_spi e6b10000.spi: IRQ rx not found
renesas_spi e6b10000.spi: IRQ mux not found
Fix this by calling platform_get_irq_byname_optional() instead.
Remove the no longer needed printing of platform_get_irq errors, as the
remaining calls to platform_get_irq() and platform_get_irq_byname() take
care of that.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191016143101.28738-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of setting up the GPIO configuration for the whole controller,
do it at CS level. It will allow to mix internal CS and GPIO CS, which
is not possible with the current implementation.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes: 4820303480 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since CSAAT functionality support has been added. Some comments become
wrong. Fix them to match the current driver behavior.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-2-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to use device_get_match_data() instead of open coded variant.
While here, switch of_property_read_bool() to device_property_read_bool().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.
Convert all users at the same time.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When improving the CS GPIO support at core level, the SPI_CS_HIGH
has been enabled for all the CS lines used for a given SPI controller.
However, the SPI framework allows to have on the same controller native
CS and GPIO CS. The native CS may not support the SPI_CS_HIGH, so they
should not be setup automatically.
With this patch the setting is done only for the CS that will use a
GPIO as CS
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018152929.3287-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In DMA mode we have a maximum transfer size, past that the driver
falls back to PIO (see the check at the top of pxa2xx_spi_transfer_one).
Falling back to PIO for big transfers defeats the point of a dma engine,
hence set the max transfer size to inform spi clients that they need
to do something smarter.
This was uncovered by the drm_mipi_dbi spi panel code, which does
large spi transfers, but stopped splitting them after:
commit e143364b4c
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Fri Jul 19 17:59:10 2019 +0200
drm/tinydrm: Remove tinydrm_spi_max_transfer_size()
After this commit the code relied on the spi core to split transfers
into max dma-able blocks, which also papered over the PIO fallback issue.
Fix this by setting the overall max transfer size to the DMA limit,
but only when the controller runs in DMA mode.
Fixes: e143364b4c ("drm/tinydrm: Remove tinydrm_spi_max_transfer_size()")
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Reported-and-tested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20191017064426.30814-1-daniel.vetter@ffwll.ch
Signed-off-by: Mark Brown <broonie@kernel.org>
For many places in the spi drivers, using the new `spi_transfer_delay`
helper is straightforward.
It's just replacing:
```
if (t->delay_usecs)
udelay(t->delay_usecs);
```
with `spi_transfer_delay(t)` which handles both `delay_usecs` and the new
`delay` field.
This change replaces in all places (in the spi drivers) where this change
is simple.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-10-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXI SPI engine driver uses the `delay_usecs` field from `spi_transfer`
to configure delays, which the controller will execute.
This change extends the logic to also include the `delay` value, in case it
is used (instead if `delay_usecs`).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-20-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver errors out if `delay_usecs` is non-zero. This error condition
should be extended to the new `delay` field, to account for when it will be
used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-19-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The WARN_ON macro prints a warning in syslog if `delay_usecs` is non-zero.
However, with the new intermediate `delay`, the warning should also be
printed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-18-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The way the max delay is computed for this controller, it looks like it is
searching for the max delay from an SPI message a using that.
No idea if this is valid. But this change should support both `delay_usecs`
and the new `delay` data which is of `spi_delay` type.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-17-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change implements CS control for setup, hold & inactive delays.
The `cs_setup` delay is completely new, and can help with cases where
asserting the CS, also brings the device out of power-sleep, where there
needs to be a longer (than usual), before transferring data.
The `cs_hold` time can overlap with the `delay` (or `delay_usecs`) from an
SPI transfer. The main difference is that `cs_hold` implies that CS will be
de-asserted.
The `cs_inactive` delay does not have a clear use-case yet. It has been
implemented mostly because the `spi_set_cs_timing()` function implements
it. To some degree, this could overlap or replace `cs_change_delay`, but
this will require more consideration/investigation in the future.
All these delays have been added to the `spi_controller` struct, as they
would typically be configured by calling `spi_set_cs_timing()` after an
`spi_setup()` call.
Software-mode for CS control, implies that the `set_cs_timing()` hook has
not been provided for the `spi_controller` object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-16-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The initial version of `spi_set_cs_timing()` was implemented with
consideration only for clock-cycles as delay.
For cases like `CS setup` time, it's sometimes needed that micro-seconds
(or nano-seconds) are required, or sometimes even longer delays, for cases
where the device needs a little longer to start transferring that after CS
is asserted.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-15-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The `delay` field has type `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `delay` is straightforward: it's just assigning the
value to `delay.value` and hard-coding the `delay.unit` to
`SPI_DELAY_UNIT_USECS`.
This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-14-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change replaces the use of the `delay_usecs` field with the new
`delay` field. The code/test still uses micro-seconds, but they are now
configured and used via the `struct spi_delay` format of the `delay` field.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-13-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This conversion to the spi_transfer_delay_exec() helper is not
straightforward, as it seems that when a delay is present, the controller
issues a command, and then a delay is followed.
This change adds support for the new `delay` field which is of type
`spi_delay` and keeps backwards compatibility with the old `delay_usecs`
field.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-12-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tegra114 driver has a weird/separate `tegra_spi_transfer_delay()`
function that does 2 delays: one mdelay() and one udelay().
This was introduced via commit f4fade12d5
("spi/tegra114: Correct support for cs_change").
There doesn't seem to be a mention in that commit message to suggest a
specific need/use-case for having the 2 delay calls.
For the most part, udelay() should be sufficient.
This change replaces it with the new `spi_transfer_delay_exec()`, which
should do the same thing.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-11-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The change introduces the `delay` field to the `spi_transfer` struct as an
`struct spi_delay` type.
This intends to eventually replace `delay_usecs`.
But, since there are many users of `delay_usecs`, this needs some
intermediate work.
A helper called `spi_transfer_delay_exec()` is also added, which maintains
backwards compatibility with `delay_usecs`, by assigning the value to
`delay` if non-zero.
This should maintain backwards compatibility with current users of
`udelay_usecs`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-9-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change does a conversion from the `word_delay_usecs` -> `word_delay`
for the `spi_device` struct.
This allows users to specify inter-word delays in other unit types
(nano-seconds or clock cycles), depending on how users want.
The Atmel SPI driver is the only current user of the `word_delay_usecs`
field (from the `spi_device` struct).
So, it needed a slight conversion to use the `word_delay` as an `spi_delay`
struct.
In SPI core, the only required mechanism is to update the `word_delay`
information per `spi_transfer`. This requires a bit more logic than before,
because it needs that both delays be converted to a common unit
(nano-seconds) for comparison.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-8-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `word_delay` is straightforward: it's just assigning the
value to `word_delay.value` and hard-coding the `word_delay.unit` to
`SPI_DELAY_UNIT_USECS`
This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-7-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `word_delay` is straightforward: it just uses the new
`spi_delay_exec()` routine, that handles the `unit` part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-6-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Spreadtrum SPI driver is the only user of the `word_delay` field in
the `spi_transfer` struct.
This change converts the field to use the `spi_delay` struct. This also
enforces the users to specify the delay unit to be `SPI_DELAY_UNIT_SCK`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-5-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.
The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.
The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.
The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are plenty of delays that have been introduced in SPI core. Most of
them are in micro-seconds, some need to be in nano-seconds, and some in
clock-cycles.
For some of these delays (related to transfers & CS timing) it may make
sense to have a `spi_delay` struct that abstracts these a bit.
The important element of these delays [for unification] seems to be the
`unit` of the delay.
It looks like micro-seconds is good enough for most people, but every-once
in a while, some delays seem to require other units of measurement.
This change adds the `spi_delay` struct & a `spi_delay_exec()` function
that processes a `spi_delay` object/struct to execute the delay.
It's a copy of the `cs_change_delay` mechanism, but without the default
for 10 uS.
The clock-cycle delay unit is a bit special, as it needs to be bound to an
`spi_transfer` object to execute.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-3-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The `cs_change_delay` backwards compatibility value could be moved outside
of the switch statement.
The only reason to do it, is to make the next patches easier to diff.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-npcm-pspi.c: In function npcm_pspi_handler:
drivers/spi/spi-npcm-pspi.c:296:6: warning: variable val set but not used [-Wunused-but-set-variable]
It is not used since commit 2a22f1b30c ("spi:
npcm: add NPCM PSPI controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-omap-100k.c: In function spi100k_read_data:
drivers/spi/spi-omap-100k.c:140:6: warning: variable dataH set but not used [-Wunused-but-set-variable]
It is not used since commit 35c9049b27 ("Add OMAP spi100k driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Later versions of the QSPI controller (e.g. in i.MX6UL/ULL and i.MX7)
seem to have an additional TDH setting in the FLSHCR register, that
needs to be set in accordance with the access mode that is used (DDR
or SDR).
Previous bootstages such as BootROM or bootloader might have used the
DDR mode to access the flash. As we currently only use SDR mode, we
need to make sure the TDH bits are cleared upon initialization.
Fixes: 84d043185d ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20191007071933.26786-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, the "interrupts" property from the device tree bindings
is ignored, even if present, if the driver runs in TCFQ mode.
Switching to using the DSPI in poll mode has several distinct
benefits:
- With interrupts, the DSPI driver in TCFQ mode raises an IRQ after each
transmitted word. There is more time wasted for the "waitq" event than
for actual I/O. And the DSPI IRQ count can easily get the largest in
/proc/interrupts on Freescale boards with attached SPI devices.
- The SPI I/O time is both lower, and more consistently so. Attached to
some Freescale devices are either PTP switches, or SPI RTCs. For
reading time off of a SPI slave device, it is important that all SPI
transfers take a deterministic time to complete.
- In poll mode there is much less time spent by the CPU in hardirq
context, which helps with the response latency of the system, and at
the same time there is more control over when interrupts must be
disabled (to get a precise timestamp measurement): win-win.
On the LS1021A-TSN board, where the SPI device is a SJA1105 PTP switch
(with a bits_per_word=8 driver), I created a "benchmark" where I read
its PTP time once per second, for 120 seconds. Each "read PTP time" is a
12-byte SPI transfer. I then recorded the time before putting the first
byte in the TX FIFO, and the time after reading the last byte from the
RX FIFO. That is the transfer delay in nanoseconds.
Interrupt mode:
delay: min 125120 max 168320 mean 150286 std dev 17675.3
Poll mode:
delay: min 69440 max 119040 mean 70312.9 std dev 8065.34
Both the mean latency and the standard deviation are more than 50% lower
in poll mode than in interrupt mode. This is with an 'ondemand' governor
on an otherwise idle system - therefore running mostly at 600 MHz out of
a max of 1200 MHz.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-5-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In this mode, the DSPI controller uses PIO to transfer word by word. In
comparison, in EOQ mode the 4-word deep FIFO is being used, hence the
current logic will need some adaptation for which I do not have the
hardware (Coldfire) to test. It is not clear what is the timing of DMA
transfers and whether timestamping in the driver brings any overall
performance increase compared to regular timestamping done in the core.
Short phc2sys summary after 58 minutes of running on LS1021A-TSN with
interrupts disabled during the critical section:
offset: min -26251 max 16416 mean -21.8672 std dev 863.416
delay: min 4720 max 57280 mean 5182.49 std dev 1607.19
lost servo lock 3 times
Summary of the same phc2sys service running for 120 minutes with
interrupts disabled:
offset: min -378 max 381 mean -0.0083089 std dev 101.495
delay: min 4720 max 5920 mean 5129.38 std dev 154.899
lost servo lock 0 times
The minimum delay (pre to post time) in nanoseconds is the same, but the
maximum delay is quite a bit higher, due to interrupts getting sometimes
executed and interfering with the measurement. Hence set disable_irqs
whenever possible (aka when the driver runs in poll mode - otherwise it
would be a contradiction in terms).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-4-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI is one of the interfaces used to access devices which have a POSIX
clock driver (real time clocks, 1588 timers etc). The fact that the SPI
bus is slow is not what the main problem is, but rather the fact that
drivers don't take a constant amount of time in transferring data over
SPI. When there is a high delay in the readout of time, there will be
uncertainty in the value that has been read out of the peripheral.
When that delay is constant, the uncertainty can at least be
approximated with a certain accuracy which is fine more often than not.
Timing jitter occurs all over in the kernel code, and is mainly caused
by having to let go of the CPU for various reasons such as preemption,
servicing interrupts, going to sleep, etc. Another major reason is CPU
dynamic frequency scaling.
It turns out that the problem of retrieving time from a SPI peripheral
with high accuracy can be solved by the use of "PTP system
timestamping" - a mechanism to correlate the time when the device has
snapshotted its internal time counter with the Linux system time at that
same moment. This is sufficient for having a precise time measurement -
it is not necessary for the whole SPI transfer to be transmitted "as
fast as possible", or "as low-jitter as possible". The system has to be
low-jitter for a very short amount of time to be effective.
This patch introduces a PTP system timestamping mechanism in struct
spi_transfer. This is to be used by SPI device drivers when they need to
know the exact time at which the underlying device's time was
snapshotted. More often than not, SPI peripherals have a very exact
timing for when their SPI-to-interconnect bridge issues a transaction
for snapshotting and reading the time register, and that will be
dependent on when the SPI-to-interconnect bridge figures out that this
is what it should do, aka as soon as it sees byte N of the SPI transfer.
Since spi_device drivers are the ones who'd know best how the peripheral
behaves in this regard, expose a mechanism in spi_transfer which allows
them to specify which word (or word range) from the transfer should be
timestamped.
Add a default implementation of the PTP system timestamping in the SPI
core. This is not going to be satisfactory performance-wise, but should
at least increase the likelihood that SPI device drivers will use PTP
system timestamping in the future.
There are 3 entry points from the core towards the SPI controller
drivers:
- transfer_one: The driver is passed individual spi_transfers to
execute. This is the easiest to timestamp.
- transfer_one_message: The core passes the driver an entire spi_message
(a potential batch of spi_transfers). The core puts the same pre and
post timestamp to all transfers within a message. This is not ideal,
but nothing better can be done by default anyway, since the core has
no insight into how the driver batches the transfers.
- transfer: Like transfer_one_message, but for unqueued drivers (i.e.
the driver implements its own queue scheduling).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver doesn't do anything with the match for the device node. The
logic is the same as looking to see if a device node exists or not
because this driver wouldn't probe unless there is a device node match
when the device is created from DT. Just test for the presence of the
device node to simplify and avoid referencing a potentially undefined
match table when CONFIG_OF=n.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-spi@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191004214334.149976-9-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, the "interrupts" property from the device tree bindings
is ignored, even if present, if the driver runs in TCFQ mode.
Switching to using the DSPI in poll mode has several distinct
benefits:
- With interrupts, the DSPI driver in TCFQ mode raises an IRQ after each
transmitted word. There is more time wasted for the "waitq" event than
for actual I/O. And the DSPI IRQ count can easily get the largest in
/proc/interrupts on Freescale boards with attached SPI devices.
- The SPI I/O time is both lower, and more consistently so. Attached to
some Freescale devices are either PTP switches, or SPI RTCs. For
reading time off of a SPI slave device, it is important that all SPI
transfers take a deterministic time to complete.
- In poll mode there is much less time spent by the CPU in hardirq
context, which helps with the response latency of the system, and at
the same time there is more control over when interrupts must be
disabled (to get a precise timestamp measurement, which will come in a
future patch): win-win.
On the LS1021A-TSN board, where the SPI device is a SJA1105 PTP switch
(with a bits_per_word=8 driver), I created a "benchmark" where I
periodically transferred a 12-byte message once per second, for 120
seconds. I then recorded the time before putting the first byte in the
TX FIFO, and the time after reading the last byte from the RX FIFO. That
is the transfer delay in nanoseconds.
Interrupt mode:
delay: min 125120 max 168320 mean 150286 std dev 17675.3
Poll mode:
delay: min 69440 max 119040 mean 70312.9 std dev 8065.34
Both the mean latency and the standard deviation are more than 50% lower
in poll mode than in interrupt mode, and the 'max' in poll mode is lower
than the 'min' in interrupt mode. This is with an 'ondemand' governor on
an otherwise idle system - therefore running mostly at 600 MHz out of a
max of 1200 MHz.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191001205216.32115-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Different platforms have different Master with different SourceID on
AHB bus. The 0X0E Master ID is used by cluster 3 in case of LS2088A.
So, patch introduce an invalid master id variable to fix invalid
mastered on different platforms.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/1569920356-8953-1-git-send-email-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In fsl_lpspi_probe an SPI controller is allocated either via
spi_alloc_slave or spi_alloc_master. In all but one error cases this
controller is put by going to error handling code. This commit fixes the
case when pm_runtime_get_sync fails and it should go to the error
handling path.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930034602.1467-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In spi_gpio_probe an SPI master is allocated via spi_alloc_master, but
this controller should be released if devm_add_action_or_reset fails,
otherwise memory leaks. In order to avoid leak spi_contriller_put must
be called in case of failure for devm_add_action_or_reset.
Fixes: 8b797490b4 ("spi: gpio: Make sure spi_master_put() is called in every error path")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930205241.5483-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change provides the dspi_slave_abort() function, which is a callback
for slave_abort() method of SPI controller generic driver.
As in the SPI slave mode the transmission is driven by master, any
distortion may cause the slave to enter undefined internal state.
To avoid this problem the dspi_slave_abort() terminates all pending and
ongoing DMA transactions (with sync) and clears internal FIFOs.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190924110547.14770-3-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/178bb78e-714f-645f-d819-5732870c4272@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/225b76ca-a367-4bef-d8ce-42c7af9242a5@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/478e0df1-e800-8cf1-f9b3-d72f8e26aa0b@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/230495a7-b754-bc6a-05e0-059a6b6c643d@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Suggested-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190919202504.9619-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AV32 support has been from the kernel a few release ago, but there was
still some specific macro for this architecture in this driver. Lets
remove it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190919154034.7489-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Renesas RZ/N1 SPI Controller is based on the Synopsys DW SSI, but has
additional registers for software CS control and DMA. This patch does not
address the changes required for DMA support, it simply adds the compatible
string. The CS registers are not needed as Linux can use gpios for the CS
signals.
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/1568793876-9009-5-git-send-email-gareth.williams.jx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable runtime PM so that the clock used to access the registers in the
peripheral is turned on using a clock domain.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/1568793876-9009-4-git-send-email-gareth.williams.jx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current initialisation of runtime PM in the orion-spi.c driver is
incorrect, because calling pm_runtime_put_autosuspend before calling
pm_runtime_get leads to a negative value of the reference count and
therefore it sometimes causes suspend during a transmission.
Signed-off-by: Tomas Paukrt <tomaspaukrt@email.cz>
Link: https://lore.kernel.org/r/E2A.ZWgn.6sH16TohXKE.1TYpoi@seznam.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
This change is necessary for spidev devices (e.g. /dev/spidev3.0) working
in the slave mode (like NXP's dspi driver for Vybrid SoC).
When SPI HW works in this mode - the master is responsible for providing
CS and CLK signals. However, when some fault happens - like for example
distortion on SPI lines - the SPI Linux driver needs a chance to recover
from this abnormal situation and prepare itself for next (correct)
transmission.
This change doesn't pose any threat on drivers working in master mode as
spi_slave_abort() function checks if SPI slave mode is supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190924110547.14770-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190925091143.15468-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the current layout which only matches early non-public revisions
of the IP. Since its official distribution, two bytes of the SPI
controller DMAS_CTRL register have been inverted.
Suggested-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190919202504.9619-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_NAND bit is a (wrongly named) placeholder that is intended
to be used in the future. Right now SPI_NOR (which is currently
identical to SPI_NAND in this version of the IP) should be used in
both cases.
Suggested-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190919202504.9619-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_TX flag.
When performing an RX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer which is copied to the TX FIFO.
The dummy buffer is necessary because the chip is not capable of
automatically clocking out null bytes.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which fills the TX FIFO by cyclically copying
from the zero page. The transaction requires very little CPU time to
submit and generates no interrupts while running. Specifics are
provided in kerneldoc comments.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/f45920af18dbf06e34129bbc406f53dc9c5d1075.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_RX flag.
When performing a TX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer into which the RX FIFO contents are
copied. The dummy buffer is necessary because the chip is not capable
of disabling the receiver or automatically throwing away received data.
Not reading the RX FIFO isn't an option either since transmission is
halted once it's full.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which cyclically clears the RX FIFO. The
transaction requires very little CPU time to submit and generates no
interrupts while running. Specifics are provided in kerneldoc comments.
With a ks8851 Ethernet chip attached to the SPI controller, I am seeing
a 30 us reduction in ping time with this commit (1.819 ms vs. 1.849 ms,
average of 100,000 packets) as well as a 2% reduction in CPU time
(75:08 vs. 76:39 for transmission of 5 GByte over the SPI bus).
The commit uses the TX DMA interrupt to signal completion of a transfer.
This interrupt is raised once all bytes have been written to the
TX FIFO and it is then necessary to busy-wait for the TX FIFO to become
empty before the transfer can be finalized. As an alternative approach,
I have explored using the SPI controller's DONE interrupt to detect
completion. This interrupt is signaled when the TX FIFO becomes empty,
avoiding the need to busy-wait. However latency deteriorates compared
to the present commit and surprisingly, CPU time is slightly higher as
well:
It turns out that in 45% of the cases, no busy-waiting is needed at all
and in 76% of the cases, less than 10 busy-wait iterations are
sufficient for the TX FIFO to drain. This was measured on an RT kernel.
On a vanilla kernel, wakeup latency is worse and thus fewer iterations
are needed. The measurements were made with an SPI clock of 20 MHz,
they may differ slightly for slower or faster clock speeds.
Previously we always used the RX DMA interrupt to signal completion of a
transfer. Using the TX DMA interrupt now introduces a race condition:
TX DMA is always started before RX DMA so that bytes are already clocked
out while RX DMA is still being set up. But if a TX-only transfer is
very short, then the TX DMA interrupt may occur before RX DMA is set up.
If the interrupt happens to occur on the same CPU, setup of RX DMA may
even be delayed until after the interrupt was handled.
I've solved this by having the TX DMA callback clear the RX FIFO while
busy-waiting for the TX FIFO to drain, thus avoiding a dependency on
setup of RX DMA. Additionally, I am using a lock-free mechanism with
two flags, tx_dma_active and rx_dma_active plus memory barriers to
terminate RX DMA either by the TX DMA callback or immediately after
setting it up, whichever wins the race. I've explored an alternative
approach which temporarily disables the TX DMA callback until RX DMA
has been set up (using tasklet_disable(), local_bh_disable() or
local_irq_save()), but the performance was minimally worse.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/874949385f28251e2dcaa9494e39a27b50e9f9e4.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver needs to set up the clock polarity in its
->prepare_message() hook before spi_transfer_one_message() asserts chip
select to avoid a gratuitous clock signal edge (cf. commit acace73df2
("spi: bcm2835: set up spi-mode before asserting cs-gpio")).
Precalculate the CS register value (which selects the clock polarity)
once in ->setup() and use that cached value in ->prepare_message() and
->transfer_one(). This avoids one MMIO read per message and one per
transfer, yielding a small latency improvement. Additionally, a
forthcoming commit will use the precalculated value to derive the
register value for clearing the RX FIFO, which will eliminate the need
for an RX dummy buffer when performing TX-only DMA transfers.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/d17c1d7fcdc97fffa961b8737cfd80eeb14f9416.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_alloc_controller() uses a single allocation to accommodate struct
spi_controller and the driver-private data, but places the latter behind
the former. This order does not guarantee cacheline alignment of the
driver-private data. (It does guarantee cacheline alignment of struct
spi_controller but the structure doesn't make any use of that property.)
Round up struct spi_controller to cacheline size. A forthcoming commit
leverages this to grant DMA access to driver-private data of the BCM2835
SPI master.
An alternative, less economical approach would be to use two allocations.
A third approach consists of reversing the order to conserve memory.
But Mark Brown is concerned that it may result in a performance penalty
on architectures that don't like unaligned accesses.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/01625b9b26b93417fb09d2c15ad02dfe9cdbbbe5.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver uses a flag to keep track of whether a DMA
transfer is in progress.
The flag is used to avoid terminating DMA channels multiple times if a
transfer finishes orderly while simultaneously the SPI core invokes the
->handle_err() callback because the transfer took too long. However
terminating DMA channels multiple times is perfectly fine, so the flag
is unnecessary for this particular purpose.
The flag is also used to avoid invoking bcm2835_spi_undo_prologue()
multiple times under this race condition. However multiple *concurrent*
invocations can no longer happen since commit 2527704d84 ("spi:
bcm2835: Synchronize with callback on DMA termination") because the
->handle_err() callback now uses the _sync() variant when terminating
DMA channels.
The only raison d'être of the flag is therefore that
bcm2835_spi_undo_prologue() cannot cope with multiple *sequential*
invocations. Achieve that by setting tx_prologue to 0 at the end of
the function. Subsequent invocations thus become no-ops.
With that, the dma_pending flag becomes unnecessary, so drop it.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/062b03b7f86af77a13ce0ec3b22e0bdbfcfba10d.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 3bd7f6589f ("spi: bcm2835: Overcome sglist entry length
limitation") amended the BCM2835 SPI driver with support for DMA
transfers whose buffers are not aligned to 4 bytes and require more than
one sglist entry.
When testing this feature with upcoming commits to speed up TX-only and
RX-only transfers, I noticed that SPI transmission sometimes breaks.
A function introduced by the commit, bcm2835_spi_transfer_prologue(),
performs one or two PIO transmissions as a prologue to the actual DMA
transmission. It turns out that the breakage goes away if the DONE bit
in the CS register is set when ending such a PIO transmission.
The DONE bit signifies emptiness of the TX FIFO. According to the spec,
the bit is of type RO, so writing it should never have any effect.
Perhaps the spec is wrong and the bit is actually of type RW1C.
E.g. the I2C controller on the BCM2835 does have an RW1C DONE bit which
needs to be cleared by the driver. Another, possibly more likely
explanation is that it's a hardware erratum since the issue does not
occur consistently.
Either way, amend bcm2835_spi_transfer_prologue() to always write the
DONE bit.
Usually a transmission is ended by bcm2835_spi_reset_hw(). If the
transmission was successful, the TX FIFO is empty and thus the DONE bit
is set when bcm2835_spi_reset_hw() reads the CS register. The bit is
then written back to the register, so we happen to do the right thing.
However if DONE is not set, e.g. because transmission is aborted with
a non-empty TX FIFO, the bit won't be written by bcm2835_spi_reset_hw()
and it seems possible that transmission might subsequently break. To be
on the safe side, likewise amend bcm2835_spi_reset_hw() to always write
the bit.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/edb004dff4af6106f6bfcb89e1a96391e96eb857.1564825752.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b2dd074a-1693-3aea-42b4-da1f5ec155c4@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This helps a bit with line fitting now (the list_first_entry call) as
well as during the next patch which needs to iterate through all
transfers of ctlr->cur_msg so it timestamps them.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-npcm-fiu.c: In function npcm_fiu_read:
drivers/spi/spi-npcm-fiu.c:472:9: warning:
variable retlen set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190905072436.23932-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-37-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-36-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-35-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-34-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-33-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-32-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-31-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-30-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-29-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-28-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-27-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-26-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-25-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-24-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-23-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-22-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-21-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-20-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-19-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-18-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190904135918.25352-17-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190904135918.25352-16-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-15-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-14-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-13-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
