In sirfsoc_dma_pm_suspend(), variable ‘sdesc’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/sirf-dma.c: In function 'sirfsoc_dma_pm_suspend':
drivers/dma/sirf-dma.c:1014:27: warning: variable 'sdesc' set but not used [-Wunused-but-set-variable]
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl330_add(), variable ‘regs’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/pl330.c: In function 'pl330_add':
drivers/dma/pl330.c:1891:16: warning: variable 'regs' set but not used [-Wunused-but-set-variable]
So remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In s3c24xx_dma_get_phy(), variable ‘cdata’ is initialized but never used, which
leads to warning with W=1. Removing this make pdata unused.
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_get_phy’:
drivers/dma/s3c24xx-dma.c:293:30: warning: variable ‘cdata’ set but not used [-Wunused-but-set-variable]
struct s3c24xx_dma_channel *cdata;
So remove both of them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘src_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:13: warning: variable ‘src_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘dst_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:23: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_chan_irq(), variable ‘sfcr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_chan_irq’:
drivers/dma/stm32-dma.c:530:19: warning: variable ‘sfcr’ set but not used [-Wunused-but-set-variable]
u32 status, scr, sfcr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pd_tx_submit(), variable ‘cookie’ is initialized but never used, which
leads to warning with W=1
drivers/dma/pch_dma.c: In function ‘pd_tx_submit’:
drivers/dma/pch_dma.c:420:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
dma_cookie_t cookie;
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mic_dma_init(), variable ‘data’ is initialized but never used, which
leads to warning with W=1
drivers/dma/mic_x100_dma.c: In function ‘mic_dma_init’:
drivers/dma/mic_x100_dma.c:557:17: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
unsigned long data;
So remove it.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mdc_prep_dma_memcpy(), mdc_prep_dma_cyclic() and mdc_prep_slave_sg()
variable ‘prev_phys’ is initialized but never used, which
leads to warning with W=1
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_memcpy’:
drivers/dma/img-mdc-dma.c:295:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_cyclic’:
drivers/dma/img-mdc-dma.c:378:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_slave_sg’:
drivers/dma/img-mdc-dma.c:461:24: warning: variable ‘prev_phys’ set but not
used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
So remove it.
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
So remove it.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In __cleanup(), variable ‘res’ is initialized but never used, which
leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘__cleanup’:
drivers/dma/ioat/dma.c:614:28: warning: variable ‘res’ set but not used [-Wunused-but-set-variable]
struct dmaengine_result res;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat_tx_submit_unlock(), variable ‘ioat_dma’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘ioat_alloc_ring_ent’:
drivers/dma/ioat/dma.c:341:25: warning: variable ‘ioat_dma’ set but not used [-Wunused-but-set-variable]
struct ioatdma_device *ioat_dma;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat3_dma_probe(), variable ‘is_raid_device’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/init.c: In function ‘ioat3_dma_probe’:
drivers/dma/ioat/init.c:1084:7: warning: variable ‘is_raid_device’ set
but not used [-Wunused-but-set-variable]
bool is_raid_device = false;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
save_gs is supposed to save the channel status in order to be restored at
resume time but it is never updated and is always 0. Anyway, the channel
status is updated in the per channel loop later in the resume function.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_xor_val_self_test(), when the calls to
dma_mapping_error() fail, the value of return variable err is 0
(indicates no error). As a result, the return value may be inconsistent
with the execution status. This patch fixes the bug by assigning
"-ENOMEM" to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188601
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_dma_self_test(), when the calls to dma_mapping_error()
fails, the value of return variable err is 0 (indicates no error). As a
result, the return value may be inconsistent with the execution status.
This patch fixes the bug by assigning -ENOMEM to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188591
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default, if we read
configuration from DT.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The last param set in a transfer should always be pointing to dummy
param set in non-cyclic mode. When system wakes from low power state
EDMA PARAM slots may be reset to random values. Hence, re-initialize
dummy slot to dummy param set on system resume.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Based on the src/dst_port_window_size - if it is set - configure the DMA
channel to use double indexing in order to be able to loop within the
address window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some slave devices uses address window instead of single register for read
and/or write of data. With the src/dst_port_window_size the address window
can be specified and the DMAengine driver should use this information to
correctly set up the transfer to loop within the provided window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Existing implementation does not honor the alignment restrictions imposed
by the DMA engines. Allocate buffers with built in slack for honoring
alignment restrictions. Creating new arrays to hold the aligned pointers
and use those pointers for operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Inside pdc_alloc_desc(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_pool_alloc does not initialize the value of the newly allocated
block for the v_lli, and the uninitilize value make the tests failed
which is on pine64 with dmatest.
we can fix it just change the "|=" to "=" for the v_lli->cfg.
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is new API in place which provides allocation mechanism of interrupts for
PCI devices. Use it in the HSU DMA driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The residue calculation was taking in consideration that dma
transaction status will be always retrieved in the dma callback
used to inform that dma transfer is complete. However this is not
the case for all subsystems that use dma. Some subsystems use a
timer to check the dma status periodically.
Therefore the calculation was updated and residue is calculated
accordingly by a) update the residue calculation taking in
consideration the last used buffer index by using *buf_ptail* variable
and b) chn_real_count (number of bytes transferred) is initialized to
zero, when dma channel is created, to avoid using an uninitialized
value in residue calculation when dma status is checked without
waiting dma complete event.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The error for DMA Transfer Source Address Error was missing.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After executing DMAGO it's possible that a request can come in for the
current xferred count, but if that happens too soon then DMAMOV SAR/DAR
may not have yet completed. If that happens, we should explicitly return 0
since nothing has been transferred yet.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to a hardware bug, reading memory (from the Accelerator Coherency Port)
with a burst size equal to the maximum burst size allowed by the DMA
hardware's buffer size will cause a hardware hang on the ARTPEC-6 SoC,
where the only solution is a manual power cycle.
On ARTPEC-6, this hardware bug does not trigger when writing memory (to the
Accelerator Coherency Port) with a burst size equal to the maximum burst
size allowed by the DMA hardware's buffer size.
To avoid this hardware hang, introduce a new optional max-burst property
for memory reads. For completeness, also introduce a max-burst property for
memory writes.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver currently uses modular infrastructure but is controlled
by a bool Kconfig.
There is a general consensus from the DMA reviewers and maintainers
that "if it can be modular, it should be modular" in order to keep
the bzImage size under control for multi platform kernels.
Build tested only. Also needed some new pm_clk symbols exported
before this commit is applied to tree in order to avoid modpost
errors like:
ERROR: "pm_clk_add_clk" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_create" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_destroy" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_suspend" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_resume" [drivers/dma/tegra210-adma.ko] undefined!
These were added as exports in the v4.8-rc1 merge window.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: dmaengine@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
$
After this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
alias: of:N*T*Cfsl,raideng-v1.0C*
alias: of:N*T*Cfsl,raideng-v1.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Just iterate over the number of elements in array chanerr_str rather
than for all 32 bits. This removes the need for a NULL chanerr_str[i]
check which could possibly overrun if the upper bits (28..31) of
chanerr are set and 27th bit in chanerr is zero. This simplifies the
code by removing an if statement and a break.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
can_pause is not initialized so it contains garbage. Fix this
by setting it to false.
Found using static analysis with cppcheck.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
