When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.
Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.
So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
clang complains about some NULL pointer arithmetic in this driver:
drivers/net/wireless/marvell/mwifiex/sta_tx.c:65:59: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*local_tx_pd) + hroom)-
^
drivers/net/wireless/marvell/mwifiex/uap_txrx.c:478:53: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*txpd) + hroom) - NULL) &
Rework that expression to do the same thing using a uintptr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927121656.940304-1-arnd@kernel.org
The BSS priority here for a new P2P_CLIENT device was accidentally set
to an enum that's certainly not meant for this. Since
MWIFIEX_BSS_ROLE_STA is 0 anyway, we can just set the bss_priority to 0
instead here.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-10-verdre@v0yd.nl
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
It's possible to change virtual interface type between P2P_CLIENT and
P2P_GO, the card supports that just fine, and it happens for example
when using miracast with the miraclecast software.
So allow type changes between P2P_CLIENT and P2P_GO and simply call into
mwifiex_change_vif_to_p2p(), which handles this just fine. We have to
call mwifiex_cfg80211_deinit_p2p() before though to make sure the old
p2p mode is properly uninitialized.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-7-verdre@v0yd.nl
In mwifiex_init_new_priv_params() we update our private driver state to
reflect the currently selected virtual interface type. Most notably we
set the bss_mode to the mode we're going to put the firmware in.
Now after we updated the driver state we actually start talking to the
firmware and instruct it to set up the new mode. Those commands can and
will sometimes fail, in which case we return with an error from
mwifiex_change_vif_to_*. We currently update our virtual interface type
counters after this return, which means the code is never reached when a
firmware error happens and we never update the counters. Since we have
updated our bss_mode earlier though, the counters now no longer reflect
the actual state of the driver.
This will break things on the next virtual interface change, because the
virtual interface type we're switching away from didn't get its counter
incremented, and we end up decrementing a 0-counter.
To fix this, simply update the virtual interface type counters right
after updating our driver structures, so that they are always in sync.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-6-verdre@v0yd.nl
Use a small helper function to increment and decrement the counter of
the interface types we currently manage. This makes the code that
actually changes and sets up the interface type a bit less messy and
also helps avoiding mistakes in case someone increments/decrements a
counter wrongly.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-5-verdre@v0yd.nl
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Instead of bailing out in the function which is supposed to do the type
change, detect invalid changes beforehand using a generic function and
return an error if the change is not allowed.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-3-verdre@v0yd.nl
Handle the obvious invalid virtual interface type changes with a general
check instead of looking at the individual change.
For type changes from P2P_CLIENT to P2P_GO and the other way round, this
changes the behavior slightly: We now still do nothing, but return
-EOPNOTSUPP instead of 0. Now that behavior was incorrect before and
still is, because type changes between these two types are actually
possible and supported, which we'll fix in a following commit.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-2-verdre@v0yd.nl
To reset mwifiex on Surface gen4+ (Pro 4 or later gen) devices, it
seems that putting the wifi device into D3cold is required according
to errata.inf file on Windows installation (Windows/INF/errata.inf).
This patch adds a function that performs power-cycle (put into D3cold
then D0) and call the function at the end of reset_prepare().
Note: Need to also reset the parent device (bridge) of wifi on SB1;
it might be because the bridge of wifi always reports it's in D3hot.
When I tried to reset only the wifi device (not touching parent), it gave
the following error and the reset failed:
acpi device:4b: Cannot transition to power state D0 for parent in D3hot
mwifiex_pcie 0000:03:00.0: can't change power state from D3cold to D0 (config space inaccessible)
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210820142050.35741-3-verdre@v0yd.nl
This commit adds the ability to apply device-specific quirks to the
mwifiex driver. It uses DMI matching similar to the quirks brcmfmac uses
with dmi.c. We'll add identifiers to match various MS Surface devices,
which this is primarily meant for, later.
This commit is a slightly modified version of a previous patch sent in
by Tsuchiya Yuto.
Co-developed-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210820142050.35741-2-verdre@v0yd.nl
Don't populate the arrays wpa_oui and wps_oui on the stack but
instead them static const. Makes the object code smaller by 63 bytes:
Before:
text data bss dec hex filename
29453 5451 64 34968 8898 .../wireless/marvell/mwifiex/sta_ioctl.o
After:
text data bss dec hex filename
29356 5611 64 35031 88d7 ../wireless/marvell/mwifiex/sta_ioctl.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819121651.7566-1-colin.king@canonical.com
There is no case in which the variable cmd_node->cmd_skb has no ->data,
and thus the variable host_cmd is guaranteed to be not NULL. Therefore,
the null-pointer check is redundant and can be dropped.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804020305.29812-1-islituo@gmail.com
The label is only used once, so we delete it and use the
return statement instead of the goto statement.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210625121108.162868-1-dingsenjie@163.com
The get_unaligned()/put_unaligned() helpers are traditionally architecture
specific, with the two main variants being the "access-ok.h" version
that assumes unaligned pointer accesses always work on a particular
architecture, and the "le-struct.h" version that casts the data to a
byte aligned type before dereferencing, for architectures that cannot
always do unaligned accesses in hardware.
Based on the discussion linked below, it appears that the access-ok
version is not realiable on any architecture, but the struct version
probably has no downsides. This series changes the code to use the
same implementation on all architectures, addressing the few exceptions
separately.
Link: https://lore.kernel.org/lkml/75d07691-1e4f-741f-9852-38c0b4f520bc@synopsys.com/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363
Link: https://lore.kernel.org/lkml/20210507220813.365382-14-arnd@kernel.org/
Link: git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git unaligned-rework-v2
Link: https://lore.kernel.org/lkml/CAHk-=whGObOKruA_bU3aPGZfoDqZM1_9wBkwREp0H0FgR-90uQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=IY5U
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-unaligned-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm/unaligned.h unification from Arnd Bergmann:
"Unify asm/unaligned.h around struct helper
The get_unaligned()/put_unaligned() helpers are traditionally
architecture specific, with the two main variants being the
"access-ok.h" version that assumes unaligned pointer accesses always
work on a particular architecture, and the "le-struct.h" version that
casts the data to a byte aligned type before dereferencing, for
architectures that cannot always do unaligned accesses in hardware.
Based on the discussion linked below, it appears that the access-ok
version is not realiable on any architecture, but the struct version
probably has no downsides. This series changes the code to use the
same implementation on all architectures, addressing the few
exceptions separately"
Link: https://lore.kernel.org/lkml/75d07691-1e4f-741f-9852-38c0b4f520bc@synopsys.com/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363
Link: https://lore.kernel.org/lkml/20210507220813.365382-14-arnd@kernel.org/
Link: git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git unaligned-rework-v2
Link: https://lore.kernel.org/lkml/CAHk-=whGObOKruA_bU3aPGZfoDqZM1_9wBkwREp0H0FgR-90uQ@mail.gmail.com/
* tag 'asm-generic-unaligned-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: simplify asm/unaligned.h
asm-generic: uaccess: 1-byte access is always aligned
netpoll: avoid put_unaligned() on single character
mwifiex: re-fix for unaligned accesses
apparmor: use get_unaligned() only for multi-byte words
partitions: msdos: fix one-byte get_unaligned()
asm-generic: unaligned always use struct helpers
asm-generic: unaligned: remove byteshift helpers
powerpc: use linux/unaligned/le_struct.h on LE power7
m68k: select CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
sh: remove unaligned access for sh4a
openrisc: always use unaligned-struct header
asm-generic: use asm-generic/unaligned.h for most architectures
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring array fields.
When preparing to call mwifiex_set_keyparamset_wep(), key_material is
treated very differently from its structure layout (which has only a
single struct mwifiex_ie_type_key_param_set). Instead, add a new type to
the union so memset() can correctly reason about the size of the
structure.
Note that the union ("params", 196 bytes) containing key_material was
not large enough to hold the target of this memset(): sizeof(struct
mwifiex_ie_type_key_param_set) == 60, NUM_WEP_KEYS = 4, so 240
bytes, or 44 bytes past the end of "params". The good news is that
it appears that the command buffer, as allocated, is 2048 bytes
(MWIFIEX_SIZE_OF_CMD_BUFFER), so no neighboring memory appears to be
getting clobbered.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210617171522.3410951-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields. Use the
sub-structure address directly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210617041431.2168953-1-keescook@chromium.org
Only one important fix for an mwifiex regression.
mwifiex
* fix deadlock during rmmod or firmware reset, regression from
cfg80211 RTNL changes in v5.12-rc1
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmDOEp8VHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bnqgIAI0PL/+2jNY6q6aJ8QK0PEYThDJH
CoWwb5JktkbqNq1nco/c7EqEKPq8TLyP3/SGhfZuiPcp2J+OlztHP3dMbQzm9du8
6rDGf/g7ZVY20GHr1rtZDNnRct054Vx/I1UMF4vMZdk2BCXrkycgvCfK5Rqg/2RU
5pA5c9/ZOguWDAbOEMAP+/G6bHFlpy1nasT5jNuYswjZJ28zgkWJKRi1QQFoe5Qn
y8TYGNCdwI4Jf93zTiiH5sJ9sFqjpMz04L9nMoEzCodgMKXAnMmqr0YjcWqxpagt
DeU80Bo189pw7CkeOEPhC75l2LM/N6llFINAAD69miPQGiyzJGZwUtxhMPE=
=rpHP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.13
Only one important fix for an mwifiex regression.
mwifiex
* fix deadlock during rmmod or firmware reset, regression from
cfg80211 RTNL changes in v5.12-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210523040339.2724-1-yuehaibing@huawei.com
There are a few leading spaces before tabs and remove it by running the
following commard:
$ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/'
$ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1621407345-10625-2-git-send-email-tanghui20@huawei.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: expecting prototype for if_usb_wrike_bulk_callback(). Prototype was for if_usb_write_bulk_callback() instead
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210517050141.61488-8-shenyang39@huawei.com
We can deadlock when rmmod'ing the driver or going through firmware
reset, because the cfg80211_unregister_wdev() has to bring down the link
for us, ... which then grab the same wiphy lock.
nl80211_del_interface() already handles a very similar case, with a nice
description:
/*
* We hold RTNL, so this is safe, without RTNL opencount cannot
* reach 0, and thus the rdev cannot be deleted.
*
* We need to do it for the dev_close(), since that will call
* the netdev notifiers, and we need to acquire the mutex there
* but don't know if we get there from here or from some other
* place (e.g. "ip link set ... down").
*/
mutex_unlock(&rdev->wiphy.mtx);
...
Do similarly for mwifiex teardown, by ensuring we bring the link down
first.
Sample deadlock trace:
[ 247.103516] INFO: task rmmod:2119 blocked for more than 123 seconds.
[ 247.110630] Not tainted 5.12.4 #5
[ 247.115796] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 247.124557] task:rmmod state:D stack: 0 pid: 2119 ppid: 2114 flags:0x00400208
[ 247.133905] Call trace:
[ 247.136644] __switch_to+0x130/0x170
[ 247.140643] __schedule+0x714/0xa0c
[ 247.144548] schedule_preempt_disabled+0x88/0xf4
[ 247.149714] __mutex_lock_common+0x43c/0x750
[ 247.154496] mutex_lock_nested+0x5c/0x68
[ 247.158884] cfg80211_netdev_notifier_call+0x280/0x4e0 [cfg80211]
[ 247.165769] raw_notifier_call_chain+0x4c/0x78
[ 247.170742] call_netdevice_notifiers_info+0x68/0xa4
[ 247.176305] __dev_close_many+0x7c/0x138
[ 247.180693] dev_close_many+0x7c/0x10c
[ 247.184893] unregister_netdevice_many+0xfc/0x654
[ 247.190158] unregister_netdevice_queue+0xb4/0xe0
[ 247.195424] _cfg80211_unregister_wdev+0xa4/0x204 [cfg80211]
[ 247.201816] cfg80211_unregister_wdev+0x20/0x2c [cfg80211]
[ 247.208016] mwifiex_del_virtual_intf+0xc8/0x188 [mwifiex]
[ 247.214174] mwifiex_uninit_sw+0x158/0x1b0 [mwifiex]
[ 247.219747] mwifiex_remove_card+0x38/0xa0 [mwifiex]
[ 247.225316] mwifiex_pcie_remove+0xd0/0xe0 [mwifiex_pcie]
[ 247.231451] pci_device_remove+0x50/0xe0
[ 247.235849] device_release_driver_internal+0x110/0x1b0
[ 247.241701] driver_detach+0x5c/0x9c
[ 247.245704] bus_remove_driver+0x84/0xb8
[ 247.250095] driver_unregister+0x3c/0x60
[ 247.254486] pci_unregister_driver+0x2c/0x90
[ 247.259267] cleanup_module+0x18/0xcdc [mwifiex_pcie]
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-wireless/98392296-40ee-6300-369c-32e16cff3725@gmail.com/
Link: https://lore.kernel.org/linux-wireless/ab4d00ce52f32bd8e45ad0448a44737e@bewaar.me/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: dave@bewaar.me
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Dave Olsthoorn <dave@bewaar.me>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210515024227.2159311-1-briannorris@chromium.org
A patch from 2017 changed some accesses to DMA memory to use
get_unaligned_le32() and similar interfaces, to avoid problems
with doing unaligned accesson uncached memory.
However, the change in the mwifiex_pcie_alloc_sleep_cookie_buf()
function ended up changing the size of the access instead,
as it operates on a pointer to u8.
Change this function back to actually access the entire 32 bits.
Note that the pointer is aligned by definition because it came
from dma_alloc_coherent().
Fixes: 92c70a958b ("mwifiex: fix for unaligned reads")
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 434256833d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit was incorrect, the error needs to be propagated back
to the caller AND if the second group call fails, the first needs to be
removed. There are much better ways to solve this, the driver should
NOT be calling sysfs_create_group() on its own as it is racing userspace
and loosing.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-53-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Building without mesh supports shows a couple of warnings with
'make W=1':
drivers/net/wireless/marvell/libertas/main.c: In function 'lbs_start_card':
drivers/net/wireless/marvell/libertas/main.c:1068:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
1068 | lbs_start_mesh(priv);
Change the macros to use the usual "do { } while (0)" instead to shut up
the warnings and make the code a litte more robust.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322104343.948660-4-arnd@kernel.org
There are a few reasons not to dump SSIDs as-is in kernel logs:
1) they're not guaranteed to be any particular text encoding (UTF-8,
ASCII, ...) in general
2) it's somewhat redundant; the BSSID should be enough to uniquely
identify the AP/STA to which we're connecting
3) BSSIDs have an easily-recognized format, whereas SSIDs do not (they
are free-form)
4) other common drivers (e.g., everything based on mac80211) get along
just fine by only including BSSIDs when logging state transitions
Additional notes on reason #3: this is important for the
privacy-conscious, especially when providing tools that convey
kernel logs on behalf of a user -- e.g., when reporting bugs. So for
example, it's easy to automatically filter logs for MAC addresses, but
it's much harder to filter SSIDs out of unstructured text.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225024454.4106485-1-briannorris@chromium.org
sturct mwl8k_dma_data contains a ieee80211_hdr structure, which is required to
have at least two byte alignment, and this conflicts with the __packed
attribute:
vers/net/wireless/marvell/mwl8k.c:811:1: warning: alignment 1 of 'struct mwl8k_dma_data' is less than 2 [-Wpacked-not-aligned]
Mark mwl8k_dma_data itself as having two-byte alignment to ensure the
inner structure is properly aligned.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210204162813.3159319-1-arnd@kernel.org
When a network is moved or reconfigured on the different channel, there
can be multiple BSSes with the same BSSID and SSID in scan result
before the old one expires. Then, it can cause cfg80211_connect_result
to map current_bss to a bss with the wrong channel.
Let mwifiex_cfg80211_assoc return the selected BSS and then the caller
can report it cfg80211_connect_bss.
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210201070649.1667209-1-yenlinlai@chromium.org
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210128162202.642848-1-colin.king@canonical.com
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgHW7nAAoJEG4XJFUm622bgd0IAKtEBcjfqnR2wW7Rt6Ah/Uch
vInrZ+5YOhjamoCvZHhTwdvUEmuRYJBT8ZqfO5x3X0GlIaJe1PlJhlvOs/9PkQ9G
eMSFcy1D/uSb3KoRRLq8lNaAy7NAyajg11IhRAeQFLeBkZgI43PGq6j7sbYCerah
87trNNlHagio9p4q9FGXVtJ2cJGQdNHM8jn4dw5Uue45YArkhj6VBh3EZl9dqV+F
XmxK+qvIcK1KPzw6nZ/0dGf8B6dnXaljn0cAzAo8QPSaZI+jozY52y3XdoKVqYRF
ekqDra4Xl/uKVZR1vb2jE5T/NtmzZI63uifndL6esEjwJMrrkRy9+alHwIxt2rU=
=KZD7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
* tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (35 commits)
iwl4965: do not process non-QOS frames on txq->sched_retry path
mt7601u: process tx URBs with status EPROTO properly
wlcore: Fix command execute failure 19 for wl12xx
mt7601u: use ieee80211_rx_list to pass frames to the network stack as a batch
rtw88: 8723de: adjust the LTR setting
rtlwifi: rtl8821ae: fix bool comparison in expressions
rtlwifi: rtl8192se: fix bool comparison in expressions
rtlwifi: rtl8188ee: fix bool comparison in expressions
rtlwifi: rtl8192c-common: fix bool comparison in expressions
rtlwifi: rtl_pci: fix bool comparison in expressions
wlcore: Downgrade exceeded max RX BA sessions to debug
wilc1000: use flexible-array member instead of zero-length array
brcmfmac: clear EAP/association status bits on linkdown events
brcmfmac: Delete useless kfree code
qtnfmac_pcie: Use module_pci_driver
mt7601u: check the status of device in calibration
mt7601u: process URBs in status EPROTO properly
brcmfmac: support BCM4365E with 43666 ChipCommon chip ID
wilc1000: fix spelling mistake in Kconfig "devision" -> "division"
mwifiex: pcie: Drop bogus __refdata annotation
...
====================
Link: https://lore.kernel.org/r/20210205161901.C7F83C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the Marvell PCIE WiFi-Ex driver does not have any code or data
located in initmem, there is no need to annotate the mwifiex_pcie
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211133835.2970384-1-geert+renesas@glider.be
mwifiex_cmd_802_11_ad_hoc_start() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Zhang Xiaohui <ruc_zhangxiaohui@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201206084801.26479-1-ruc_zhangxiaohui@163.com
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
commit 932183aa35 ("mwifiex: change license text from MARVELL
to NXP") does this, but it left out two files.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606814307-32715-1-git-send-email-ganapathi.bhat@nxp.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117160958.GA18807@embeddedor
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.
So, let's update the comments at the top of each function accordingly.
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_pcie_remove’:
drivers/net/wireless/marvell/mwifiex/pcie.c:432:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_cleanup_pcie’:
drivers/net/wireless/marvell/mwifiex/pcie.c:3142:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-32-lee.jones@linaro.org
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
libertas uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug macro prints (INT) when in_interrupt() returns true. The value of
this information is dubious as it does not distinguish between the various
contexts which are covered by in_interrupt().
As the usage of in_interrupt() in drivers is phased out and the same
information can be more precisely obtained with tracing, remove the
in_interrupt() conditional from this debug printk.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
mwifiex uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analyzer reports this problem
init.c:739:8: warning: Called function pointer
is null (null dereference)
ret = adapter->if_ops.check_fw_status( ...
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In mwifiex_dnld_fw, there is an earlier check for check_fw_status(),
The check was introduced for usb support at the same time this
check in _mwifiex_fw_dpc() was made
if (adapter->if_ops.dnld_fw) {
ret = adapter->if_ops.dnld_fw(adapter, &fw);
} else {
ret = mwifiex_dnld_fw(adapter, &fw);
}
And a dnld_fw function initialized as part the usb's
mwifiex_if_ops.
The other instances of mwifiex_if_ops for pci and sdio
both set check_fw_status.
So the first check is not needed and can be removed.
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906200548.18053-1-trix@redhat.com
These variables only used in sdio.c, move them to .c file
can silence these warnings:
In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com
In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
static const u8 tos_to_tid_inv[] = {
^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
^~~~~~~~~~~~~~~~~~~~~~~
move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com
Saves on 10's of complains about 'defined but not used' variables.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/marvell/mwifiex/main.h:57,
from drivers/net/wireless/marvell/mwifiex/main.c:22:
drivers/net/wireless/marvell/mwifiex/pcie.h:310:41: warning: ‘mwifiex_pcie8997’ defined but not used [-Wunused-const-variable=]
310 | static const struct mwifiex_pcie_device mwifiex_pcie8997 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:300:41: warning: ‘mwifiex_pcie8897’ defined but not used [-Wunused-const-variable=]
300 | static const struct mwifiex_pcie_device mwifiex_pcie8897 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:292:41: warning: ‘mwifiex_pcie8766’ defined but not used [-Wunused-const-variable=]
292 | static const struct mwifiex_pcie_device mwifiex_pcie8766 = {
| ^~~~~~~~~~~~~~~~
NB: Repeats 10's of times - snipped for brevity.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-2-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: Function parameter or member 'urb' not described in 'if_usb_write_bulk_callback'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:73: warning: Function parameter or member 'cardp' not described in 'if_usb_free'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'intf' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'id' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:244: warning: Function parameter or member 'intf' not described in 'if_usb_disconnect'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:272: warning: Function parameter or member 'cardp' not described in 'if_usb_send_fw_pkt'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'cardp' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'payload' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'nb' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'data' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:625: warning: Function parameter or member 'urb' not described in 'if_usb_receive'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'priv' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'type' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'payload' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'nb' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'cardp' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'ivalue' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'data' not described in 'check_fwfile_format'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'totlen' not described in 'check_fwfile_format'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Function parameter or member 'device' not described in 'lbs_get_firmware_async'
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Excess function parameter 'dev' description in 'lbs_get_firmware_async'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/main.c:727: warning: Function parameter or member 't' not described in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:727: warning: Excess function parameter 'data' description in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Function parameter or member 't' not described in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Excess function parameter 'data' description in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Function parameter or member 't' not described in 'auto_deepsleep_timer_fn'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Excess function parameter 'data' description in 'auto_deepsleep_timer_fn'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-15-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Also demote one stray non-kernel-doc header.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'priv' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'extra' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'resp' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:80: warning: Function parameter or member 'priv' not described in 'lbtf_update_hw_spec'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'priv' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'channel' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'priv' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'cmdnode' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:442: warning: Function parameter or member 'priv' not described in 'lbtf_allocate_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:490: warning: Function parameter or member 'priv' not described in 'lbtf_free_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:527: warning: Function parameter or member 'priv' not described in 'lbtf_get_cmd_ctrl_node'
drivers/net/wireless/marvell/libertas_tf/cmd.c:561: warning: Function parameter or member 'priv' not described in 'lbtf_execute_next_command'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-8-lee.jones@linaro.org
There are only 2 kernel-doc headers in this file and both are
incorrect. The first one does not attempt to document the function at
all and the second one is suffering from severe doc-rot; the format is
wrong and only 1 out of 3 parameters are being documented.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/main.c:129: warning: Function parameter or member 't' not described in 'command_timer_fn'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'card' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'dmdev' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'ops' not described in 'lbtf_add_card'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-5-lee.jones@linaro.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-12-allen.cryptic@gmail.com
Following commit e186967865 ("mwifiex: Prevent memory corruption
handling keys") the mwifiex driver fails to authenticate with certain
networks, specifically networks with 256 bit keys, and repeatedly asks
for the password. The kernel log repeats the following lines (id and
bssid redacted):
mwifiex_pcie 0000:01:00.0: info: trying to associate to '<id>' bssid <bssid>
mwifiex_pcie 0000:01:00.0: info: associated to bssid <bssid> successfully
mwifiex_pcie 0000:01:00.0: crypto keys added
mwifiex_pcie 0000:01:00.0: info: successfully disconnected from <bssid>: reason code 3
Tracking down this problem lead to the overflow check introduced by the
aforementioned commit into mwifiex_ret_802_11_key_material_v2(). This
check fails on networks with 256 bit keys due to the current storage
size for AES keys in struct mwifiex_aes_param being only 128 bit.
To fix this issue, increase the storage size for AES keys to 256 bit.
Fixes: e186967865 ("mwifiex: Prevent memory corruption handling keys")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: Kaloyan Nikolov <konik98@gmail.com>
Tested-by: Kaloyan Nikolov <konik98@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200825153829.38043-1-luzmaximilian@gmail.com
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
The error message if 'pci_set_consistent_dma_mask()' fails is misleading.
The function call uses 32 bits, but the error message reports 64.
Moreover, according to the comment above 'dma_set_mask_and_coherent()'
definition, such an error can never happen.
So, simplify code, axe the misleading message and use
'dma_set_mask_and_coherent()' instead of 'dma_set_mask()' +
'dma_set_coherent_mask()'
While at it, make some clean-up:
- add # when reporting allocated length to be consistent between
functions
- s/consistent/coherent/
- s/unsigned int/u32/ to be consistent between functions
- align some code
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819071853.113185-1-christophe.jaillet@wanadoo.fr
A possible call chain is as follow:
mwifiex_sdio_interrupt (sdio.c)
--> mwifiex_main_process (main.c)
--> mwifiex_process_cmdresp (cmdevt.c)
--> mwifiex_process_sta_cmdresp (sta_cmdresp.c)
--> mwifiex_ret_802_11_scan (scan.c)
--> mwifiex_parse_single_response_buf (scan.c)
'mwifiex_sdio_interrupt()' is an interrupt function.
Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.
So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.
Fixes: 7c6fa2a843 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfKUIHAAoJEG4XJFUm622bXqkH/jgjKWh4b96Pv56jLPtyoPKj
q9ZvIS1MFhfeY/DFX2gAx34iOwDi7lRVsb1r8IX+rui+B4yTDkvgM2azduSfUpA7
+WOHaQdRYMbUa0YlvotaxFaHpqABKFnRd3zQKTMgT3LyVgj6OMiyHhc7DJTrBvMM
KR+Z6/aNmMccWcSR4OPPF8zPRmp7h5yLW55UgqfOm0JzRfCnXtq6vb6MUDxYelGm
ruvKP2W86m0DfQzPSwCEdSPkD/2aspi9HrMJNXm/cNqGk6AFQTZzPpQC6PowSrWA
9rpzBRti2OwDD6Q6QJqmWzQ8pclP4BMZWPyYBqaC8tTHDvD13OV/siZVk9nP+As=
=KOz+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The length of the key comes from the network and it's a 16 bit number. It
needs to be capped to prevent a buffer overflow.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200708115857.GA13729@mwanda
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
This macro is already used in mwifiex driver for specifying upper limit and
is defined to value 3. So use it also in struct ieee80211_iface_limit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200626152938.12737-1-pali@kernel.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Firmware for sd8997 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8997_combo_v4.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8997.
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8977 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8977_combo_v2.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8977.
Fixes: 1a0f547831 ("mwifiex: add support for sd8977 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to
inform kernel about maximum number of p2p connections and stations in AP
mode.
During initialization of SD8997 wifi chip kernel prints warning:
mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217
This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets
appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure.
It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123559.29028-1-pali@kernel.org
During initialization of SD8997 wifi chip kernel prints warnings:
mwifiex_sdio mmc0:0001:1: Unknown api_id: 3
mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
This patch adds support for parsing all api ids provided by SD8997
firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123444.28957-1-pali@kernel.org
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
