When booting with an initial ramdisk on platforms where physical memory
does not start at address zero (e.g. on Amiga):
initrd: 0ef0602c - 0f800000
Zone ranges:
DMA [mem 0x0000000008000000-0x000000f7ffffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000008000000-0x000000000f7fffff]
Initmem setup node 0 [mem 0x0000000008000000-0x000000000f7fffff]
Unable to handle kernel access at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<00201d3c>] memcmp+0x28/0x56
As phys_to_virt() relies on m68k_memoffset and module_fixup(), it must
not be called before paging_init(). Hence postpone the phys_to_virt
handling for the initial ramdisk until after calling paging_init().
While at it, reduce #ifdef clutter by using IS_ENABLED() instead.
Fixes: 376e3fdecb ("m68k: Enable memtest functionality")
Reported-by: Stephen Walsh <vk3heg@vk3heg.net>
Link: https://lists.debian.org/debian-68k/2022/09/msg00007.html
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/4f45f05f377bf3f5baf88dbd5c3c8aeac59d94f0.camel@physik.fu-berlin.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/dff216da09ab7a60217c3fc2147e671ae07d636f.1677528627.git.geert@linux-m68k.org
This is useful on !virt platforms for kexec, so change things from
BI_VIRT_RNG_SEED to be BI_RNG_SEED, and simply remove BI_VIRT_RNG_SEED
because it only ever lasted one release, and nothing is broken by not
having it. At the same time, keep a comment noting that it's been
removed, so that ID isn't reused. In addition, we previously documented
2-byte alignment, but 4-byte alignment is actually necessary, so update
that comment.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: a1ee38ab1a ("m68k: virt: Use RNG seed from bootinfo block")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20220927130835.1629806-2-Jason@zx2c4.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The RNG seed boot record is memzeroed after processing, in order to
preserve forward secrecy. By saving the bootinfo for procfs prior to
that, forward secrecy is violated, since it becomes possible to recover
past states. So, save the bootinfo block only after first processing
them.
Fixes: a1ee38ab1a ("m68k: virt: Use RNG seed from bootinfo block")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20220927130835.1629806-1-Jason@zx2c4.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Add Tegra234 cpufreq support (Sumit Gupta).
- Clean up and enhance the Mediatek cpufreq driver (Wan Jiabing,
Rex-BC Chen, and Jia-Wei Chang).
- Fix up the CPPC cpufreq driver after recent changes (Zheng Bin,
Pierre Gondois).
- Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine
Oudjana).
- Use list iterator only inside the list_for_each_entry loop (Xiaomeng
Tong, and Jakob Koschel).
- New APIs related to finding OPP based on interconnect bandwidth
(Krzysztof Kozlowski).
- Fix the missing of_node_put() in _bandwidth_supported() (Dan
Carpenter).
- Cleanups (Krzysztof Kozlowski, and Viresh Kumar).
- Add Out of Band mode description to the intel-speed-select utility
documentation (Srinivas Pandruvada).
- Add power sequences support to the system reboot and power off
code and make related platform-specific changes for multiple
platforms (Dmitry Osipenko, Geert Uytterhoeven).
-----BEGIN PGP SIGNATURE-----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=PAh+
-----END PGP SIGNATURE-----
Merge tag 'pm-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These update the ARM cpufreq drivers and fix up the CPPC cpufreq
driver after recent changes, update the OPP code and PM documentation
and add power sequences support to the system reboot and power off
code.
Specifics:
- Add Tegra234 cpufreq support (Sumit Gupta)
- Clean up and enhance the Mediatek cpufreq driver (Wan Jiabing,
Rex-BC Chen, and Jia-Wei Chang)
- Fix up the CPPC cpufreq driver after recent changes (Zheng Bin,
Pierre Gondois)
- Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine
Oudjana)
- Use list iterator only inside the list_for_each_entry loop
(Xiaomeng Tong, and Jakob Koschel)
- New APIs related to finding OPP based on interconnect bandwidth
(Krzysztof Kozlowski)
- Fix the missing of_node_put() in _bandwidth_supported() (Dan
Carpenter)
- Cleanups (Krzysztof Kozlowski, and Viresh Kumar)
- Add Out of Band mode description to the intel-speed-select utility
documentation (Srinivas Pandruvada)
- Add power sequences support to the system reboot and power off code
and make related platform-specific changes for multiple platforms
(Dmitry Osipenko, Geert Uytterhoeven)"
* tag 'pm-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (60 commits)
cpufreq: CPPC: Fix unused-function warning
cpufreq: CPPC: Fix build error without CONFIG_ACPI_CPPC_CPUFREQ_FIE
Documentation: admin-guide: PM: Add Out of Band mode
kernel/reboot: Change registration order of legacy power-off handler
m68k: virt: Switch to new sys-off handler API
kernel/reboot: Add devm_register_restart_handler()
kernel/reboot: Add devm_register_power_off_handler()
soc/tegra: pmc: Use sys-off handler API to power off Nexus 7 properly
reboot: Remove pm_power_off_prepare()
regulator: pfuze100: Use devm_register_sys_off_handler()
ACPI: power: Switch to sys-off handler API
memory: emif: Use kernel_can_power_off()
mips: Use do_kernel_power_off()
ia64: Use do_kernel_power_off()
x86: Use do_kernel_power_off()
sh: Use do_kernel_power_off()
m68k: Switch to new sys-off handler API
powerpc: Use do_kernel_power_off()
xen/x86: Use do_kernel_power_off()
parisc: Use do_kernel_power_off()
...
. correctly set up ZERO_PAGE pointer
. drop ISA_DMA_API support
. fix comment typos
. fixes for undefined symbols
. remove unused code and variables
. elf-fdpic loader support for m68k
-----BEGIN PGP SIGNATURE-----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=O3zh
-----END PGP SIGNATURE-----
Merge tag 'm68knommu-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"A collection of changes to add elf-fdpic loader support for m68k.
Also a collection of various fixes. They include typo corrections,
undefined symbol compilation fixes, removal of the ISA_DMA_API support
and removal of unused code.
Summary:
- correctly set up ZERO_PAGE pointer
- drop ISA_DMA_API support
- fix comment typos
- fixes for undefined symbols
- remove unused code and variables
- elf-fdpic loader support for m68k"
* tag 'm68knommu-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 68000 CPU link with no platform selected
m68k: removed unused "mach_get_ss"
m68knommu: fix undefined reference to `mach_get_rtc_pll'
m68knommu: fix undefined reference to `_init_sp'
m68knommu: allow elf_fdpic loader to be selected
m68knommu: add definitions to support elf_fdpic program loader
m68knommu: implement minimal regset support
m68knommu: use asm-generic/mmu.h for nommu setups
m68k: fix typos in comments
m68k: coldfire: drop ISA_DMA_API support
m68knommu: set ZERO_PAGE() to the allocated zeroed page
The m68k machine helper function "mach_get_ss" function pointer is
set for some machines, but ultimately never used anywhere. Remove it.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Configuring for a nommu classic m68k target and enabling the generic rtc
driver (CONFIG_RTC_DRV_GENERIC) will result in the following compile
error:
m68k-linux-ld: arch/m68k/kernel/time.o: in function `rtc_ioctl':
time.c:(.text+0x82): undefined reference to `mach_get_rtc_pll'
m68k-linux-ld: time.c:(.text+0xbc): undefined reference to `mach_set_rtc_pll'
m68k-linux-ld: time.c:(.text+0xf4): undefined reference to `mach_set_rtc_pll'
There are no definitions of "mach_set_rtc_pll" and "mach_get_rtc_pll" in the
nommu code paths. Move these definitions and the associated "mach_hwclk",
so that they are around their use case in time.c. This means they will
always be defined on the builds that require them, and not on those that
cannot use them - such as ColdFire (both with and without MMU enabled).
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Kernel now supports chained power-off handlers. Use
register_power_off_handler() that registers power-off handlers and
do_kernel_power_off() that invokes chained power-off handlers. Legacy
pm_power_off() will be removed once all drivers will be converted to
the new sys-off API.
Normally arch code should adopt only the do_kernel_power_off() at first,
but m68k is a special case because it uses pm_power_off() "inside out",
i.e. pm_power_off() invokes machine_power_off() [in fact it does nothing],
while it's machine_power_off() that should invoke the pm_power_off(), and
thus, we can't convert platforms to the new API separately. There are only
two platforms changed here, so it's not a big deal.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This machine allows to have up to 3.2 GiB and 128 Virtio devices.
It is based on android goldfish devices.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/r/20220406201523.243733-5-laurent@vivier.eu
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
To avoid 'warning: no previous prototype for' errors, declare all the
parse_bootinfo and config function prototypes into asm/config.h and
include it in arch/m68k/kernel/setup_mm.c and arch/m68k/*/config.c.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/r/20220121200738.2577697-2-laurent@vivier.eu
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is no good reason to keep genhd.h separate from the main blkdev.h
header that includes it. So fold the contents of genhd.h into blkdev.h
and remove genhd.h entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Enable the memtest functionality and rearrange some code to prevent it
from clobbering the initrd.
The code to implement CONFIG_BLK_DEV_INITRD was conditional on
!defined(CONFIG_SUN3). For simplicity, remove that test on the basis
that m68k_ramdisk.size == 0 on Sun 3. The SLIME source code at
http://sammy.net/sun3/ftp/pub/m68k/sun3/slime/slime-2.0.tar.gz
indicates that no BI_RAMDISK entry is ever passed to the kernel due
to #ifdef 0 around the relevant code.
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/r/8170fe1d1c62426d82275d36ba409ecc18754292.1637274578.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This cleans up two ancient timer features that were never completed in
the past, CONFIG_GENERIC_CLOCKEVENTS and CONFIG_ARCH_USES_GETTIMEOFFSET.
There was only one user left for the ARCH_USES_GETTIMEOFFSET variant
of clocksource implementations, the ARM EBSA110 platform. Rather than
changing to use modern timekeeping, we remove the platform entirely as
Russell no longer uses his machine and nobody else seems to have one
any more.
The conditional code for using arch_gettimeoffset() is removed as
a result.
For CONFIG_GENERIC_CLOCKEVENTS, there are still a couple of platforms
not using clockevent drivers: parisc, ia64, most of m68k, and one
Arm platform. These all do timer ticks slighly differently, and this
gets cleaned up to the point they at least all call the same helper
function. Instead of most platforms using 'select GENERIC_CLOCKEVENTS'
in Kconfig, the polarity is now reversed, with the few remaining ones
selecting LEGACY_TIMER_TICK instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=QpNs
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-timers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cross-architecture timer cleanup from Arnd Bergmann:
"This cleans up two ancient timer features that were never completed in
the past, CONFIG_GENERIC_CLOCKEVENTS and CONFIG_ARCH_USES_GETTIMEOFFSET.
There was only one user left for the ARCH_USES_GETTIMEOFFSET variant
of clocksource implementations, the ARM EBSA110 platform. Rather than
changing to use modern timekeeping, we remove the platform entirely as
Russell no longer uses his machine and nobody else seems to have one
any more.
The conditional code for using arch_gettimeoffset() is removed as a
result.
For CONFIG_GENERIC_CLOCKEVENTS, there are still a couple of platforms
not using clockevent drivers: parisc, ia64, most of m68k, and one Arm
platform. These all do timer ticks slighly differently, and this gets
cleaned up to the point they at least all call the same helper
function.
Instead of most platforms using 'select GENERIC_CLOCKEVENTS' in
Kconfig, the polarity is now reversed, with the few remaining ones
selecting LEGACY_TIMER_TICK instead"
* tag 'asm-generic-timers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
timekeeping: default GENERIC_CLOCKEVENTS to enabled
timekeeping: remove xtime_update
m68k: remove timer_interrupt() function
m68k: change remaining timers to legacy_timer_tick
m68k: m68328: use legacy_timer_tick()
m68k: sun3/sun3c: use legacy_timer_tick
m68k: split heartbeat out of timer function
m68k: coldfire: use legacy_timer_tick()
parisc: use legacy_timer_tick
ARM: rpc: use legacy_timer_tick
ia64: convert to legacy_timer_tick
timekeeping: add CONFIG_LEGACY_TIMER_TICK
timekeeping: remove arch_gettimeoffset
net: remove am79c961a driver
ARM: remove ebsa110 platform
This information is unused since the discontinuous memory support
has been introduced in 2007.
Fixes: 12d810c1b8 ("m68k: discontinuous memory support")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/r/20201009095621.833192-1-laurent@vivier.eu
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This gets passed to a number of init functions, but is
ignored everywhere, so remove the function and change the
mach_sched_init callback to take no arguments.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
con_init in tty/vt.c will now set conswitchp to dummy_con if it's unset.
Drop it from arch setup code.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20191218214506.49252-11-nivedita@alum.mit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A multi-platform kernel binary has to decide at run-time how to dispatch
the arch_nvram_ops calls. Add a platform-independent arch_nvram_ops
struct for this, to replace the atari-specific one.
Enable CONFIG_HAVE_ARCH_NVRAM_OPS for Macs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running the kernel in Fast RAM on Atari:
Ignoring memory chunk at 0x0:0xe00000 before the first chunk
...
Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<0069dbac>] free_all_bootmem+0x12c/0x186
SR: 2714 SP: (ptrval) a2: 005e3314
d0: 00000000 d1: 0000000a d2: 00000e00 d3: 00000000
d4: 005e1fc0 d5: 0000001a a0: 01000000 a1: 00000000
Process swapper (pid: 0, task=(ptrval))
Frame format=7 eff addr=00000736 ssw=0505 faddr=00000736
wb 1 stat/addr/data: 0000 00000000 00000000
wb 2 stat/addr/data: 0000 00000000 00000000
wb 3 stat/addr/data: 0000 00000736 00000000
push data: 00000000 00000000 00000000 00000000
Stack from 005e1f84:
00000000 0000000a 027d3260 006b5006 00000000 00000000 00000000 00000000
0004f062 0003a220 0069e272 005e1ff8 0000054c 00000000 00e00000 00000000
00000001 00693cd8 027d3260 0004f062 0003a220 00691be6 00000000 00000000
00000000 00000000 00000000 00000000 006b5006 00000000 00690872
Call Trace: [<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<0069e272>] memblock_virt_alloc_try_nid+0x0/0xa4
[<00693cd8>] mem_init+0xa/0x5c
[<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<00691be6>] start_kernel+0x1ca/0x462
[<00690872>] _sinittext+0x872/0x11f8
Code: 7a1a eaae 2270 6db0 0061 ef14 2f01 2f03 <96a9> 0736 2203 e589 d681 e78b d6a9 0732 2f03 2f40 0034 4eb9 0069 b8d0 260e 4fef
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill the idle task!
As the kernel must run in the memory chunk with the lowest address,
ST-RAM is ignored, and removed from the m68k_memory[] array.
However, it is not removed from memblock, causing a crash later.
More investigation shows that there are 3 places where memory chunks are
ignored, all after the calls to memblock_add() in m68k_parse_bootinfo(),
and thus causing crashes:
1. On classic m68k CPUs with a MMU, paging_init() ignores all memory
chunks below the first chunk, cfr. above,
2. On Amigas equipped with a Zorro III bus, config_amiga() ignores all
Zorro II memory,
3. If CONFIG_SINGLE_MEMORY_CHUNK=y, m68k_parse_bootinfo() ignores all
but the first memory chunk.
Fix this by moving the calls to memblock_add() from
m68k_parse_bootinfo() to paging_init(), after all ignored memory chunks
have been removed from m68k_memory[].
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Fixes: 1008a11590 ("m68k: switch to MEMBLOCK + NO_BOOTMEM")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In m68k the physical memory is described by [memory_start, memory_end] for
!MMU variant and by m68k_memory array of memory ranges for the MMU version.
This information is directly use to register the physical memory with
memblock.
The reserve_bootmem() calls are replaced with memblock_reserve() and the
bootmap bitmap allocation is simply dropped.
Since the MMU variant creates early mappings only for the small part of the
memory we force bottom-up allocations in memblock.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Commit 397ac99c6c ("m68k: remove dead timer code") removed set_rtc_mmss()
because it was unused in 2012. However, this was itself the only user of the
mach_set_clock_mmss() callback and the many implementations of that callback,
which are equally unused.
This removes all of those as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is possible to select INPUT_M68K_BEEP in a nommu configuration. This
results in the following link error:
drivers/input/misc/m68kspkr.o: In function `m68kspkr_event':
m68kspkr.c:(.text+0x3a): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x5e): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x78): undefined reference to `mach_beep'
drivers/input/misc/m68kspkr.o: In function `m68kspkr_init':
m68kspkr.c:(.init.text+0x4): undefined reference to `mach_beep'
Pull the mach_beep definition in setup.c to avoid it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The M54[78]x ColdFire parts are not the only members of the ColdFire family
that have an MMU. But currently some of the early MMU initialization code
is inside the startup code specific to only the ColdFire M54[78]x parts.
Move that early ColdFire MMU init code so that it is run for other ColdFire
parts running with MMU enabled.
Specifically this means that the MMU initialization code will now also be
run for the ColdFire M5441x parts when running with MMU enabled.
The code move meant that the extern definition for the mmu_context_init()
function had to be moved as well. To make it clear that is ColdFire specific
I have renamed that with a "cf_" in front of it and put its extern definition
in the mcfmmu.h (which is already included by the setup code).
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull m68knommu updates from Greg Ungerer:
"The bulk of the changes here are to clean up the ColdFire 5441x SoC
support so that it can run with MMU enabled. We have only supported it
with MMU disabled up to now.
There is also a few individual bug fixes across the ColdFire support
code"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: let clk_disable() return immediately if clk is NULL
m68knommu: convert printk(KERN_INFO) to pr_info()
m68knommu: clean up uClinux boot log output
m68k: generalize uboot command line support
m68k: don't panic if no hardware FPU defined
m68k: only generate FPU instructions if CONFIG_FPU enabled
m68k: always make available dump_fpu()
m68k: generalize io memory region setup for ColdFire ACR registers
m68k: move ColdFire _bootmem_alloc code
m68k: report correct FPU type on ColdFire MMU platforms
m68k: set appropriate machine type for m5411x SoC platforms
m68k: move CONFIG_FPU set to per-CPU configuration
m68knommu: fix IO write size in nettel pin set
m68knommu: switch to using IO access methods in WildFire board code
m68knommu: fix early setup to not access variables
The uboot command line support needs to be used by both MMU and no-MMU
setups, but currently we only have the code in the no-MMU code paths.
Move the uboot command line processing code into its own file. Add
appropriate calls to it from both the MMU and no-MMU arch setup code.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If we boot up and find no hardware FPU we panic and die.
Change this behavior to be that if we boot up and we _expect_ a hardware
FPU to be present then panic. Don't panic if we don't actually expect to
have any hardware FPU.
This lets us compile a kernel without FPU if we really choose too.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Most of the m68k code that supports a hardware FPU is surrounded by
CONFIG_FPU. Be consistent and surround the hardware FPU instruction
setup in setup_mm.c with CONFIG_FPU as well as the check for
CONFIG_M68KFPU_EMU_ONLY.
The existing classic m68k architectures all define CONFIG_FPU, so they
see no change from this. But on ColdFire where we do not support the
emulated FP code we can now compile without CONFIG_FPU being set as well.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Create a new machine type for platforms based around the ColdFire 5441x
SoC family. Set that machine type on startup when building for this
platform type.
Currently the ColdFire head.S hard codes a M54xx machine type at startup -
since that is the only platform type currently supported with MMU enabled.
The m5441x has an MMU and this change forms part of the support required
to run it with the MMU enabled.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Add optional support to export the bootinfo used to boot the kernel in a
"bootinfo" file in procfs. This is useful with kexec.
This is based on the similar feature for ATAGS on ARM.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
nf_init() uses virt_to_phys(), which depends on m68k_memoffset being set and
module_fixup() having been called, but this is only done in paging_init().
Hence call paging_init() before nf_init().
This went unnoticed, as virt_to_phys() is a no-op on Atari, unless you start
fiddling with the memory blocks in the bootinfo manually.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move generic definitions used by bootstraps to uapi/asm/bootinfo.h:
- Machine types,
- CPU, FPU, and MMU types,
- struct mem_info.
Keep a copy of struct mem_info for in-kernel use, and rename it to struct
m68k_mem_info, as the exported one will be modified later.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since the introduction of init sections (which are located after BSS), the
bootinfo is no longer located right after the BSS, but after all kernel
sections.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Atari ROM port ISA adapter support for EtherNEC and NetUSBee adapters
16 bit access for ROM port adapters follows debugging and
clarification by David Galvez <dgalvez75@gmail.com>. The NetUSBee
ISP1160 USB chip uses these macros.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
remove m68k's mach_gettimeoffset function pointer, and instead directly
set the arch_gettimeoffset function pointer. This requires multiplying
all function results by 1000, since the removed m68k_gettimeoffset() did
this. Also, s/unsigned long/u32/ just to make the function prototypes
exactly match that of arch_gettimeoffset.
Cc: Joshua Thompson <funaho@jurai.org>
Cc: Sam Creasey <sammy@sammy.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Phil Blundell <philb@gnu.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The V4e ColdFire CPU family also has an integrated FPU (as well as the MMU).
So add code to support this hardware along side the existing m68k FPU code.
The ColdFire FPU is of course different to all previous 68k FP units. It is
close in operation to the 68060, but not completely compatible. The biggest
issue to deal with is that the ColdFire FPU multi-move instructions are
different. It does not support multi-moving the FP control registers, and
the multi-move of the FP data registers uses a different instruction
mnemonic.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
We use the same setup code for ColdFire MMU enabled platforms as
standard m68k. So add support for it to setup our 54xx ColdFire
platforms. They do not support the same bootinfo parsing as other
m68k platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Update the show_cpuinfo() code to display info about ColdFire cores.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
The non-MMU builds of m68k allow a fixed kernel boot command line to
be configured at configure time. Allow this MMU builds as well.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Geert Uytterhoeven