According to datasheet section 8.12.19, when there's no TSN offloading
Shadow_QbvCycle bit[29:0] must be set to zero for basic scheduling.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one phy->type: copper. There is no point checking
phy->type during the igc_has_link method from the watchdog that
invoked every 2 seconds.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one PHY vendor. There is no point checking
_I_PHY_ID during the link establishment and auto-negotiation process.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a spelling mistake in the comment block.
Signed-off-by: Tree Davies <tdavies@darkphysics.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Minor fixes to allow debug prints more readable.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platforms
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Lunar Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After transferring the MAC-PHY interface to the SMBus set the PHY
to S0ix low power idle mode.
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Per guidance from the CSME architecture team, it may take
up to 1 second for unconfiguring dynamic power gating mode.
Practically it can take more time. Wait up to 2.5 seconds to indicate
dynamic power gating exit from the S0ix configuration. Detect
scenarios that take more than 1 second but less than 2.5 seconds
will emit warning message.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On the corporate system, the driver will ask from the CSME
(manageability engine) to perform device settings are required
to allow S0ix residency.
This patch provides initial support.
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The DMA code section of the decompressor must be compiled with expolines
if Spectre V2 mitigation has been enabled for the decompressed kernel.
This is required because although the decompressor's image contains
the DMA code section, it is handed over to the decompressed kernel for use.
Because the DMA code is already slow w/o expolines, use expolines always
regardless whether the decompressed kernel is using them or not. This
simplifies the DMA code by dropping the conditional compilation of
expolines.
Fixes: bf72630130 ("s390: use proper expoline sections for .dma code")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6206b7981a.
That patch added additional spin_{un}lock_bh(), which was harmless
but pointless. The orginal code path has guaranteed the pair of
spin_{un}lock_bh().
We'd better revert it before we find the exact root cause of the
bug_on mentioned in that patch.
Fixes: 6206b7981a ("qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()")
Cc: David S. Miller <davem@davemloft.net>
Cc: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running the self-tests on a KASAN enabled kernel, I observed a
slab-out-of-bounds splat very similar to the one reported in
commit 821bbf79fe ("ipv6: Fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions").
We additionally need to take care of fib6_metrics initialization
failure when the caller provides an nh.
The fix is similar, explicitly free the route instead of calling
fib6_info_release on a half-initialized object.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The character sequence ??! is a trigraph and causes the following
clang warning:
drivers/net/ethernet/marvell/mvneta.c:2604:39: warning: trigraph ignored [-Wtrigraphs]
Clean this by replacing it with single ?.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The character sequence ??) is a trigraph and causes the following
clang warning:
drivers/atm/idt77252.c:3544:35: warning: trigraph ignored [-Wtrigraphs]
Clean this by replacing it with single ?.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the possibility to configure the RGMII RX/TX clock skew via
devicetree.
Simply set phy mode to "rgmii-id", "rgmii-rxid" or "rgmii-txid" and add
the "rx-internal-delay-ps" or "tx-internal-delay-ps" property to the
devicetree.
Furthermore, a warning is now issued if the phy mode is configured to
"rgmii" and an internal delay is set in the phy (e.g. by pin-strapping),
as in the dp83867 driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for Armada 8040 says:
Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
When <PortType> = 1 (1000BASE-X) this field must be set to 1.
We presently ignore whether userspace requests autonegotiation or not
through the ethtool ksettings interface. However, we have some network
interfaces that wish to do this. To offer a consistent API across
network interfaces, deny the ability to disable autonegotiation on
mvpp2 hardware when in 1000BASE-X and 2500BASE-X.
This means the only way to switch between 2500BASE-X and 1000BASE-X
on SFPs that support this will be:
# ethtool -s ethX advertise 0x20000006000 # 1000BASE-X Pause AsymPause
# ethtool -s ethX advertise 0xe000 # 2500BASE-X Pause AsymPause
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for Armada 38x says:
Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
When <PortType> = 1 (1000BASE-X) this field must be set to 1.
We presently ignore whether userspace requests autonegotiation or not
through the ethtool ksettings interface. However, we have some network
interfaces that wish to do this. To offer a consistent API across
network interfaces, deny the ability to disable autonegotiation on
mvneta hardware when in 1000BASE-X and 2500BASE-X.
This means the only way to switch between 2500BASE-X and 1000BASE-X
on SFPs that support this will be:
# ethtool -s ethX advertise 0x20000002000 # 1000BASE-X Pause
# ethtool -s ethX advertise 0xa000 # 2500BASE-X Pause
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set SUPPORTED_FIBRE to mac_dev->if_support. It allows proper usage of
PHYs with optical/fiber support.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Root in init user namespace can modify /proc/sys/net/ipv4/ip_forward
without CAP_NET_ADMIN, this doesn't follow the principle of
capabilities. For example, let's take a look at netdev_store(),
root can't modify netdev attribute without CAP_NET_ADMIN.
So let's keep the consistency of permission check logic.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcf_skbmod_act() assumes that packets use Ethernet as their L2
protocol, which is not always the case. As an example, for CAN devices:
$ ip link add dev vcan0 type vcan
$ ip link set up vcan0
$ tc qdisc add dev vcan0 root handle 1: htb
$ tc filter add dev vcan0 parent 1: protocol ip prio 10 \
matchall action skbmod swap mac
Doing the above silently corrupts all the packets. Do not perform skbmod
actions for non-Ethernet packets.
Fixes: 86da71b573 ("net_sched: Introduce skbmod action")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
arm64: dts: qcom: DTS updates
This series updates some IPA-related DT nodes.
Newer versions of IPA do not require an interconnect between IPA
and SoC internal memory. The first patch updates the DT binding
to reflect this.
The second patch adds IPA information to "sc7280.dtsi", using only
two interconnects. It includes the definition of the reserved
memory area used to hold IPA firmware.
The last patch defines the reserved IPA firmware memory area in
"sc7180.dtsi".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the reserved memory space used for IPA firmware for the
Qualcomm SC7180 SoC.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPA-related nodes and definitions to "sc7280.dtsi", including
the reserved memory area used for AP-based IPA firmware loading.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some newer SoCs, the interconnect between IPA and SoC internal
memory (imem) is not used. Reflect this in the binding by moving
the definition of the "imem" interconnect to the end and defining
minItems to be 2 for both the interconnects and interconnect-names
properties.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently three interconnects are defined for the Qualcomm SC7280
SoC, but this was based on a misunderstanding. There should only be
two interconnects defined: one between the IPA and system memory;
and another between the AP and IPA config space. The bandwidths
defined for the memory and config interconnects do not match what I
understand to be proper values, so update these.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is observed when running 'make dtbs_check':
Documentation/devicetree/bindings/net/fsl,fec.yaml:85:7: [warning] wrong indentation: expected 8 but found 6 (indentation)
Fix the indentation accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fan out FDB entries pointing towards the bridge to all switchdev member ports
The "DSA RX filtering" series has added some important support for
interpreting addresses towards the bridge device as host addresses and
installing them as FDB entries towards the CPU port, but it does not
cover all circumstances and needs further work.
To be precise, the mechanism introduced in that series only works as
long as the ports are fairly static and no port joins or leaves the
bridge once the configuration is done. If any port leaves, host FDB
entries that were installed during runtime (for example the user changes
the MAC address of the bridge device) will be prematurely deleted,
resulting in a broken setup.
I see this work as targeted for "net-next" because technically it was
not supposed to work. Also, there are still corner cases and holes to be
plugged. For example, today, FDB entries on foreign interfaces are not
covered by br_fdb_replay(), which means that there are cases where some
host addresses are either lost, or never deleted by DSA. That will be
resolved once more work gets accepted, in particular the "Allow
forwarding for the software bridge data path to be offloaded to capable
devices" series, which moves the br_fdb_replay() call to the bridge core
and therefore would be required to solve the problem in a generic way
for every switchdev driver and not just for DSA.
These patches also pave the way for a cleaner implementation for FDB
entries pointing towards a LAG upper interface in DSA (that code needs
only to be added, nothing changed), however this is not done here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the new fan-out helper for FDB entries installed on the software
bridge, we can install host addresses with the proper refcount on the
CPU port, such that this case:
ip link set swp0 master br0
ip link set swp1 master br0
ip link set swp2 master br0
ip link set swp3 master br0
ip link set br0 address 00:01:02:03:04:05
ip link set swp3 nomaster
works properly and the br0 address remains installed as a host entry
with refcount 3 instead of getting deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA has an issue with FDB entries pointing towards the bridge
in the presence of br_fdb_replay() being called at port join and leave
time.
In particular, each bridge port will ask for a replay for the FDB
entries pointing towards the bridge when it joins, and for another
replay when it leaves.
This means that for example, a bridge with 4 switch ports will notify
DSA 4 times of the bridge MAC address.
But if the MAC address of the bridge changes during the normal runtime
of the system, the bridge notifies switchdev [ once ] of the deletion of
the old MAC address as a local FDB towards the bridge, and of the
insertion [ again once ] of the new MAC address as a local FDB.
This is a problem, because DSA keeps the old MAC address as a host FDB
entry with refcount 4 (4 ports asked for it using br_fdb_replay). So the
old MAC address will not be deleted. Additionally, the new MAC address
will only be installed with refcount 1, and when the first switch port
leaves the bridge (leaving 3 others as still members), it will delete
with it the new MAC address of the bridge from the local FDB entries
kept by DSA (because the br_fdb_replay call on deletion will bring the
entry's refcount from 1 to 0).
So the problem, really, is that the number of br_fdb_replay() calls is
not matched with the refcount that a host FDB is offloaded to DSA during
normal runtime.
An elegant way to solve the problem would be to make the switchdev
notification emitted by br_fdb_change_mac_address() result in a host FDB
kept by DSA which has a refcount exactly equal to the number of ports
under that bridge. Then, no matter how many DSA ports join or leave that
bridge, the host FDB entry will always be deleted when there are exactly
zero remaining DSA switch ports members of the bridge.
To implement the proposed solution, we remember that the switchdev
objects and port attributes have some helpers provided by switchdev,
which can be optionally called by drivers:
switchdev_handle_port_obj_{add,del} and switchdev_handle_port_attr_set.
These helpers:
- fan out a switchdev object/attribute emitted for the bridge towards
all the lower interfaces that pass the check_cb().
- fan out a switchdev object/attribute emitted for a bridge port that is
a LAG towards all the lower interfaces that pass the check_cb().
In other words, this is the model we need for the FDB events too:
something that will keep an FDB entry emitted towards a physical port as
it is, but translate an FDB entry emitted towards the bridge into N FDB
entries, one per physical port.
Of course, there are many differences between fanning out a switchdev
object (VLAN) on 3 lower interfaces of a LAG and fanning out an FDB
entry on 3 lower interfaces of a LAG. Intuitively, an FDB entry towards
a LAG should be treated specially, because FDB entries are unicast, we
can't just install the same address towards 3 destinations. It is
imaginable that drivers might want to treat this case specifically, so
create some methods for this case and do not recurse into the LAG lower
ports, just the bridge ports.
DSA also listens for FDB entries on "foreign" interfaces, aka interfaces
bridged with us which are not part of our hardware domain: think an
Ethernet switch bridged with a Wi-Fi AP. For those addresses, DSA
installs host FDB entries. However, there we have the same problem
(those host FDB entries are installed with a refcount of only 1) and an
even bigger one which we did not have with FDB entries towards the
bridge:
br_fdb_replay() is currently not called for FDB entries on foreign
interfaces, just for the physical port and for the bridge itself.
So when DSA sniffs an address learned by the software bridge towards a
foreign interface like an e1000 port, and then that e1000 leaves the
bridge, DSA remains with the dangling host FDB address. That will be
fixed separately by replaying all FDB entries and not just the ones
towards the port and the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a bit difficult to understand what DSA checks when it tries to
avoid installing dynamically learned addresses on foreign interfaces as
local host addresses, so create a generic switchdev helper that can be
reused and is generally more readable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes my earlier patch which broke vlan unaware bridges.
The IVL bit now only gets set for vid's larger than 1.
Fixes: 11d8d98cbe ("mt7530 fix mt7530_fdb_write vid missing ivl bit")
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subbaraya Sundeep says:
====================
octeontx2-af: Introduce DMAC based switching
With this patch set packets can be switched between
all CGX mapped PFs and VFs in the system based on
the DMAC addresses. To implement this:
AF allocates high priority rules from top entry(0) in MCAM.
Rules are allocated for all the CGX mapped PFs and VFs though
they are not active and with no NIXLFs attached.
Rules for a PF/VF will be enabled only after they are brought up.
Two rules one for TX and one for RX are allocated for each PF/VF.
A packet sent from a PF/VF with a destination mac of another
PF/VF will be hit by TX rule and sent to LBK channel 63. The
same returned packet will be hit by RX rule whose action is
to forward packet to PF/VF with that destination mac.
Implementation of this for 98xx is tricky since there are
two NIX blocks and till now a PF/VF can install rule for
an NIX0/1 interface only if it is mapped to corresponding NIX0/1 block.
Hence Tx rules are modified such that TX interface in MCAM
entry can be either NIX0-TX or NIX1-TX.
Testing:
1. Create two VFs over PF1(on NIX0) and assign two VFs to two VMs
2. Assign ip addresses to two VFs in VMs and PF2(on NIX1) in host.
3. Assign static arp entries in two VMs and PF2.
4. Ping between VMs and host PF2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver to support the Maxlinear GPY115, GPY211, GPY212, GPY215,
GPY241, GPY245 PHYs. Separate from XWAY PHY driver because this series
has different register layout and new features not supported in XWAY PHY.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Acked-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add API to read 802.3-c45 IDs so that C22/C45 mixed device can use
C45 APIs without failing ID checks.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Acked-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Olteans says:
====================
Proper cross-chip support for tag_8021q
The cross-chip bridging support for tag_8021q/sja1105 introduced here:
https://patchwork.ozlabs.org/project/netdev/cover/20200510163743.18032-1-olteanv@gmail.com/
took some shortcuts and is not reusable in other topologies except for
the one it was written for: disjoint DSA trees. A diagram of this
topology can be seen here:
https://patchwork.ozlabs.org/project/netdev/patch/20200510163743.18032-3-olteanv@gmail.com/
However there are sja1105 switches on other boards using other
topologies, most notably:
- Daisy chained:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
- "H" topology:
eth0 eth1
| |
CPU port CPU port
| DSA link |
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4 -------- sw1p4 sw1p3 sw1p2 sw1p1 sw1p0
| | | | | |
user user user user user user
port port port port port port
In fact, the current code for tag_8021q cross-chip links works for
neither of these 2 classes of topologies.
The main reasons are:
(a) The sja1105 driver does not treat DSA links. In the "disjoint trees"
topology, the routing port towards any other switch is also the CPU
port, and that was already configured so it already worked.
This series does not deal with enabling DSA links in the sja1105
driver, that is a fairly trivial task that will be dealt with
separately.
(b) The tag_8021q code for cross-chip links assumes that any 2 switches
between cross-chip forwarding needs to be enabled (i.e. which have
user ports part of the same bridge) are at most 1 hop away from each
other. This was true for the "disjoint trees" case because
once a packet reached the CPU port, VLAN-unaware bridging was done
by the DSA master towards the other switches based on destination
MAC address, so the tag_8021q header was not interpreted in any way.
However, in a daisy chain setup with 3 switches, all of them will
interpret the tag_8021q header, and all tag_8021q VLANs need to be
installed in all switches.
When looking at the O(n^2) real complexity of the problem, it is clear
that the current code had absolutely no chance of working in the general
case. So this patch series brings a redesign of tag_8021q, in light of
its new requirements. Anything with O(n^2) complexity (where n is the
number of switches in a DSA tree) is an obvious candidate for the DSA
cross-chip notifier support.
One by one, the patches are:
- The sja1105 driver is extremely entangled with tag_8021q, to be exact,
with that driver's best_effort_vlan_filtering support. We drop this
operating mode, which means that sja1105 temporarily loses network
stack termination for VLAN-aware bridges. That operating mode raced
itself to its own grave anyway due to some hardware limitations in
combination with PTP reported by NXP customers. I can't say a lot
more, but network stack termination for VLAN-aware bridges in sja1105
will be reimplemented soon with a much, much better solution.
- What remains of tag_8021q in sja1105 is support for standalone ports
mode and for VLAN-unaware bridging. We refactor the API surface of
tag_8021q to a single pair of dsa_tag_8021q_{register,unregister}
functions and we clean up everything else related to tag_8021q from
sja1105 and felix.
- Then we move tag_8021q into the DSA core. I thought about this a lot,
and there is really no other way to add a DSA_NOTIFIER_TAG_8021Q_VLAN_ADD
cross-chip notifier if DSA has no way to know if the individual
switches use tag_8021q or not. So it needs to be part of the core to
use notifiers.
- Then we modify tag_8021q to update dynamically on bridge_{join,leave}
events, instead of what we have today which is simply installing the
VLANs on all ports of a switch and leaving port isolation up to
somebody else. This change is necessary because port isolation over a
DSA link cannot be done in any other way except based on VLAN
membership, as opposed to bridging within the same switch which had 2
choices (at least on sja1105).
- Finally we add 2 new cross-chip notifiers for adding and deleting a
tag_8021q VLAN, which is properly refcounted similar to the bridge FDB
and MDB code, and complete cleanup is done on teardown (note that this
is unlike regular bridge VLANs, where we currently cannot do
refcounting because the user can run "bridge vlan add dev swp0 vid 100"
a gazillion times, and "bridge vlan del dev swp0 vid 100" just once,
and for some reason expect that the VLAN will be deleted. But I digress).
With this opportunity we remove a lot of hard-to-digest code and
replace it with much more idiomatic DSA-style code.
This series was regression-tested on:
- Single-switch boards with SJA1105T
- Disjoint-tree boards with SJA1105S and Felix (using ocelot-8021q)
- H topology boards using SJA1110A
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The big problem which mandates cross-chip notifiers for tag_8021q is
this:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
When the user runs:
ip link add br0 type bridge
ip link set sw0p0 master br0
ip link set sw2p0 master br0
It doesn't work.
This is because dsa_8021q_crosschip_bridge_join() assumes that "ds" and
"other_ds" are at most 1 hop away from each other, so it is sufficient
to add the RX VLAN of {ds, port} into {other_ds, other_port} and vice
versa and presto, the cross-chip link works. When there is another
switch in the middle, such as in this case switch 1 with its DSA links
sw1p3 and sw1p4, somebody needs to tell it about these VLANs too.
Which is exactly why the problem is quadratic: when a port joins a
bridge, for each port in the tree that's already in that same bridge we
notify a tag_8021q VLAN addition of that port's RX VLAN to the entire
tree. It is a very complicated web of VLANs.
It must be mentioned that currently we install tag_8021q VLANs on too
many ports (DSA links - to be precise, on all of them). For example,
when sw2p0 joins br0, and assuming sw1p0 was part of br0 too, we add the
RX VLAN of sw2p0 on the DSA links of switch 0 too, even though there
isn't any port of switch 0 that is a member of br0 (at least yet).
In theory we could notify only the switches which sit in between the
port joining the bridge and the port reacting to that bridge_join event.
But in practice that is impossible, because of the way 'link' properties
are described in the device tree. The DSA bindings require DT writers to
list out not only the real/physical DSA links, but in fact the entire
routing table, like for example switch 0 above will have:
sw0p3: port@3 {
link = <&sw1p4 &sw2p4>;
};
This was done because:
/* TODO: ideally DSA ports would have a single dp->link_dp member,
* and no dst->rtable nor this struct dsa_link would be needed,
* but this would require some more complex tree walking,
* so keep it stupid at the moment and list them all.
*/
but it is a perfect example of a situation where too much information is
actively detrimential, because we are now in the position where we
cannot distinguish a real DSA link from one that is put there to avoid
the 'complex tree walking'. And because DT is ABI, there is not much we
can change.
And because we do not know which DSA links are real and which ones
aren't, we can't really know if DSA switch A is in the data path between
switches B and C, in the general case.
So this is why tag_8021q RX VLANs are added on all DSA links, and
probably why it will never change.
On the other hand, at least the number of additions/deletions is well
balanced, and this means that once we implement reference counting at
the cross-chip notifier level a la fdb/mdb, there is absolutely zero
need for a struct dsa_8021q_crosschip_link, it's all self-managing.
In fact, with the tag_8021q notifiers emitted from the bridge join
notifiers, it becomes so generic that sja1105 does not need to do
anything anymore, we can just delete its implementation of the
.crosschip_bridge_{join,leave} methods.
Among other things we can simply delete is the home-grown implementation
of sja1105_notify_crosschip_switches(). The reason why that is wrong is
because it is not quadratic - it only covers remote switches to which we
have a cross-chip bridging link and that does not cover in-between
switches. This deletion is part of the same patch because sja1105 used
to poke deep inside the guts of the tag_8021q context in order to do
that. Because the cross-chip links went away, so needs the sja1105 code.
Last but not least, dsa_8021q_setup_port() is simplified (and also
renamed). Because our TAG_8021Q_VLAN_ADD notifier is designed to react
on the CPU port too, the four dsa_8021q_vid_apply() calls:
- 1 for RX VLAN on user port
- 1 for the user port's RX VLAN on the CPU port
- 1 for TX VLAN on user port
- 1 for the user port's TX VLAN on the CPU port
now get squashed into only 2 notifier calls via
dsa_port_tag_8021q_vlan_add.
And because the notifiers to add and to delete a tag_8021q VLAN are
distinct, now we finally break up the port setup and teardown into
separate functions instead of relying on a "bool enabled" flag which
tells us what to do. Arguably it should have been this way from the
get go.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been at least one wasted opportunity for tag_8021q to be used
by a driver:
https://patchwork.ozlabs.org/project/netdev/patch/20200710113611.3398-3-kurt@linutronix.de/#2484272
because of a design decision: the declared purpose of tag_8021q is to
offer source port/switch identification for a tagging driver for packets
coming from a switch with no hardware DSA tagging support. It is not
intended to provide VLAN-based port isolation, because its first user,
sja1105, had another mechanism for bridging domain isolation, the L2
Forwarding Table. So even if 2 ports are in the same VLAN but they are
separated via the L2 Forwarding Table, they will not communicate with
one another. The L2 Forwarding Table is managed by the
sja1105_bridge_join() and sja1105_bridge_leave() methods.
As a consequence, today tag_8021q does not bother too much with hooking
into .port_bridge_join() and .port_bridge_leave() because that would
introduce yet another degree of freedom, it just iterates statically
through all ports of a switch and adds the RX VLAN of one port to all
the others. In this way, whenever .port_bridge_join() is called,
bridging will magically work because the RX VLANs are already installed
everywhere they need to be.
This is not to say that the reason for the change in this patch is to
satisfy the hellcreek and similar use cases, that is merely a nice side
effect. Instead it is to make sja1105 cross-chip links work properly
over a DSA link.
For context, sja1105 today supports a degenerate form of cross-chip
bridging, where the switches are interconnected through their CPU ports
("disjoint trees" topology). There is some code which has been
generalized into dsa_8021q_crosschip_link_{add,del}, but it is not
enough, and frankly it is impossible to build upon that.
Real multi-switch DSA trees, like daisy chains or H trees, which have
actual DSA links, do not work.
The problem is that sja1105 is unlike mv88e6xxx, and does not have a PVT
for cross-chip bridging, which is a table by which the local switch can
select the forwarding domain for packets from a certain ingress switch
ID and source port. The sja1105 switches cannot parse their own DSA
tags, because, well, they don't really have support for DSA tags, it's
all VLANs.
So to make something like cross-chip bridging between sw0p0 and sw1p0 to
work over the sw0p3/sw1p3 DSA link to work with sja1105 in the topology
below:
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] ---- [ dsa ] [ cpu ] [ user ] [ user ]
we need to ask ourselves 2 questions:
(1) how should the L2 Forwarding Table be managed?
(2) how should the VLAN Lookup Table be managed?
i.e. what should prevent packets from going to unwanted ports?
Since as mentioned, there is no PVT, the L2 Forwarding Table only
contains forwarding rules for local ports. So we can say "all user ports
are allowed to forward to all CPU ports and all DSA links".
If we allow forwarding to DSA links unconditionally, this means we must
prevent forwarding using the VLAN Lookup Table. This is in fact
asymmetric with what we do for tag_8021q on ports local to the same
switch, and it matters because now that we are making tag_8021q a core
DSA feature, we need to hook into .crosschip_bridge_join() to add/remove
the tag_8021q VLANs. So for symmetry it makes sense to manage the VLANs
for local forwarding in the same way as cross-chip forwarding.
Note that there is a very precise reason why tag_8021q hooks into
dsa_switch_bridge_join() which acts at the cross-chip notifier level,
and not at a higher level such as dsa_port_bridge_join(). We need to
install the RX VLAN of the newly joining port into the VLAN table of all
the existing ports across the tree that are part of the same bridge, and
the notifier already does the iteration through the switches for us.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, setting up tag_8021q is a 2-step operation for a driver,
first the context structure needs to be created, then the VLANs need to
be installed on the ports. A similar thing is true for teardown.
Merge the 2 steps into the register/unregister methods, to be as
transparent as possible for the driver as to what tag_8021q does behind
the scenes. This also gets rid of the funny "bool setup == true means
setup, == false means teardown" API that tag_8021q used to expose.
Note that dsa_tag_8021q_register() must be called at least in the
.setup() driver method and never earlier (like in the driver probe
function). This is because the DSA switch tree is not initialized at
probe time, and the cross-chip notifiers will not work.
For symmetry with .setup(), the unregister method should be put in
.teardown().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tag_8021q a more central element of DSA and move the 2 driver
specific operations outside of struct dsa_8021q_context (which is
supposed to hold dynamic data and not really constant function
pointers).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic problem description is as follows:
Be there 3 switches in a daisy chain topology:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
The CPU will not be able to ping through the user ports of the
bottom-most switch (like for example sw2p0), simply because tag_8021q
was not coded up for this scenario - it has always assumed DSA switch
trees with a single switch.
To add support for the topology above, we must admit that the RX VLAN of
sw2p0 must be added on some ports of switches 0 and 1 as well. This is
in fact a textbook example of thing that can use the cross-chip notifier
framework that DSA has set up in switch.c.
There is only one problem: core DSA (switch.c) is not able right now to
make the connection between a struct dsa_switch *ds and a struct
dsa_8021q_context *ctx. Right now, it is drivers who call into
tag_8021q.c and always provide a struct dsa_8021q_context *ctx pointer,
and tag_8021q.c calls them back with the .tag_8021q_vlan_{add,del}
methods.
But with cross-chip notifiers, it is possible for tag_8021q to call
drivers without drivers having ever asked for anything. A good example
is right above: when sw2p0 wants to set itself up for tag_8021q,
the .tag_8021q_vlan_add method needs to be called for switches 1 and 0,
so that they transport sw2p0's VLANs towards the CPU without dropping
them.
So instead of letting drivers manage the tag_8021q context, add a
tag_8021q_ctx pointer inside of struct dsa_switch, which will be
populated when dsa_tag_8021q_register() returns success.
The patch is fairly long-winded because we are partly reverting commit
5899ee367a ("net: dsa: tag_8021q: add a context structure") which made
the driver-facing tag_8021q API use "ctx" instead of "ds". Now that we
can access "ctx" directly from "ds", this is no longer needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming patches will add tag_8021q related logic to switch.c and
port.c, in order to allow it to make use of cross-chip notifiers.
In addition, a struct dsa_8021q_context *ctx pointer will be added to
struct dsa_switch.
It seems fairly low-reward to #ifdef the *ctx from struct dsa_switch and
to provide shim implementations of the entire tag_8021q.c calling
surface (not even clear what to do about the tag_8021q cross-chip
notifiers to avoid compiling them). The runtime overhead for switches
which don't use tag_8021q is fairly small because all helpers will check
for ds->tag_8021q_ctx being a NULL pointer and stop there.
So let's make it part of dsa_core.o.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of moving tag_8021q to core DSA, move all initialization
and teardown related to tag_8021q which is currently done by drivers in
2 functions called "register" and "unregister". These will gather more
functionality in future patches, which will better justify the chosen
naming scheme.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer necessary since tag_8021q doesn't register itself as a
full-blown tagger anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pe to give the user a string holding the error code instead of just
a number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
