The PCH transcoder registers are only 12 bits wide for the hdisplay
and hblank_start values. On HSW/BDW the CPU side registers are 13
bits wide. intel_mode_valid() only checks against the higher limit
(since we don't know where the mode is to be used), so an extra
check is required against the FDI limits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615174406.12258-3-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
On ICL the pipe clock needs to be enabled before setting the HDMI
infoframe, but these steps are in the reverse order atm. Move the pipe
clock enabling to the encoders, so reordering of the two steps can be
done in a clean way.
No functional change.
v2:
- Rebased on drm-tip.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613172746.18525-1-imre.deak@intel.com
When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.
Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.
To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.
Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b81 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Clean up the ADPA pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state()
and the port state asserts.
v2: Order the defines shift,mask,value (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514172423.9302-1-ville.syrjala@linux.intel.com
When doing forced load detection testing we should totally ignore any
hotplug status for the connector. This is mostly relevant for machines
where we already ignore the hotplug status based on the DMI quirks. On
other machines we would currently skip the force load detection tests
on account of the connector already being connected.
v2: Drop the other force_load_detect check since it's useless now (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322174135.5982-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The LG 4k TV I have doesn't deassert HPD when I turn the TV off, but
when I turn it back on it will pulse the HPD line. By that time it has
forgotten everything we told it about scrambling and the clock ratio.
Hence if we want to get a picture out if it again we have to tell it
whether we're currently sending scrambled data or not. Implement
that via the encoder->hotplug() hook.
v2: Force a full modeset to not follow the HDMI 2.0 spec more
closely (Shashank)
[pushed with whitespace fixes to make sparse happy]
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-1-ville.syrjala@linux.intel.com
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
The code describes what it is doing quite well; and that is now much
more complex than what the old comment would let you believe.
drivers/gpu/drm/i915/intel_crt.c:486: warning: Function parameter or member 'connector' not described in 'intel_crt_detect_hotplug'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214092909.27040-1-chris@chris-wilson.co.uk
clang is confused by our if-else-chain that abruptly exits before a
final else:
drivers/gpu/drm/i915/intel_crt.c:821:11: warning: variable 'status' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
else if (ret < 0)
^~~~~~~
drivers/gpu/drm/i915/intel_crt.c:826:9: note: uninitialized use occurs here
return status;
^~~~~~
drivers/gpu/drm/i915/intel_crt.c:821:7: note: remove the 'if' if its condition is always true
else if (ret < 0)
^~~~~~~~~~~~
drivers/gpu/drm/i915/intel_crt.c:761:12: note: initialize the variable 'status' to silence this warning
int status, ret;
In this case, we can reduce the final else-if clause to an unconditional
else.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208163939.27030-1-chris@chris-wilson.co.uk
We never support certain mode flags etc. Reject those early on in the
mode_config.mode_valid() hook. That allows us to remove some duplicated
checks from the connector .mode_valid() hooks, and it guarantees that
we never see those flags even from user mode as the
mode_config.mode_valid() hooks gets executed for those as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-11-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace crtc->config usage with the passed down crtc state.
Also take the opportunity for some s/pipe_config/crtc_state/ while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-7-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Rather than having the caller of .get_config() set output_types based on
encoder->type, let's just have .get_config() itself populate
output_types. This way we are isolated from encoder->type, which won't
be useable for this purpose anyway soon (at least for DDI encoders).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.
v5: pure rename
v6: fix
Credits-to: Coccinelle
@@
identifier n;
@@
(
- i915.n
+ i915_modparams.n
)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com
The enable/disable/etc. encoder hooks aren't supposed to alter the
state(s), so pass them as const. Unfortunately C lacks any kind of deep
const thingy, so this can't catch all abuses. But at least it acts as a
hint to the reader telling them not to mess about with the state(s).
v2: Update intel_tv_mode_find() and ironlake_edp_pll_on() as well
v3: Deal with intel_sdvo_connector_state
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-9-ville.syrjala@linux.intel.com
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
It's dead code, the core handles all this directly now. This also
allows us to unexport drm_atomic_helper_connector_set_property.
The only special case is nouveau which used one function for both
pre-nv50 legacy modeset code and post-nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
What is rather strange here is how few drivers set this up, I suspect
the earlier patch to handle properties in the core did end up fixing a
pile of possible issues.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-7-daniel.vetter@ffwll.ch
Acked-by: Vincent Abriou <vincent.abriou@st.com>
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
In the path where intel_crt_detect_ddc() detects a CRT, if would return
true without freeing the edid.
Fixes: a2bd1f541f ("drm/i915: check whether we actually received an edid in detect_ddc")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Pass dev_priv to intel_setup_outputs() and functions called by it, since
those are all intel i915 specific functions. Also, in the majority of
the functions dev_priv is used more often than dev. In the rare cases
where there are a few calls back into drm core, a local dev variable was
added.
v2: Don't convert dev to &dev_priv->drm in intel_dsi_init. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479910904-11005-1-git-send-email-ander.conselvan.de.oliveira@intel.com
A bunch of source files with just a few instances of the
incorrect INTEL_INFO use.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
A small selection of macros which can only accept dev_priv from
now on and a resulting trickle of fixups.
v2: Keep original order. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Saves 944 bytes of .rodata strings and 128 bytes of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
This saves 3248 bytes of .rodata strings.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Intel DZ77BH-55K board doest't have a physical VGA connector,
and yet it always detects that something is connected there.
Add it to the DMI blacklist to ignore the spurious detection
results.
Allows me to drop 'video=VGA-1:d' from my kernel cmdline.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474881646-1326-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having a shadow VGA connector is useful for testing purposes. We
currently skip registering the connector on machines where the
CRT detect falsely reports it as connected. Let's instead move the
the blacklist check to the detect callback (and hpd setup) and
if we get a match we always report the connector as disconnected.
This way we get a shadow VGA connector to help with testing, while
we still avoid the user facing problems from the incorrect
detection results.
commit 8ca4013d70 ("CHROMIUM: i915: Add DMI override to skip CRT
initialization on ZGB") doesn't provide much in the way of details
as to why 'ACER ZGB' was added to the blacklist. Trying to trace it
further leads me to a chromeos bugreport I can't access. So based on
the fact that the commit added the
"/* Skip machines without VGA that falsely report hotplug events */"
comment, I'm going to assume that it was just spurious CRT detection.
So it should be safe to move the blacklist to just block the detection
and hpd without causing a regression on said machine.
In fact Stéphane confirmed on irc that the problem was indeed just
crappy hotplug detect:
"22:29 < marcheu> vsyrjala: the port isn't there, but the load detect is
improperly stubbed in hw
22:29 < marcheu> vsyrjala: so it floats"
so this change should be perfectly fine.
v2: Add irc quote from Stéphane
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474881646-1326-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Storing the port enum in intel_encoder makes it convenient to know the
port attached to an encoder. Moving the port information up from
intel_digital_port to intel_encoder avoids unecessary intel_digital_port
access and handles MST encoders cleanly without requiring conditional
checks for them (thanks danvet).
v2:
Renamed the port enum member from 'attached_port' to 'port' (danvet)
Fixed missing initialization of port in intel_sdvo.c (danvet)
v3:
Fixed missing initialization of port in intel_crt.c (Ville)
v4:
Storing port for DVO encoders too.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-3-git-send-email-dhinakaran.pandiyan@intel.com
Instead of iterating overthe connectors manually, run the last part of
DDI disabling inside the crt post disable function.
This was meant to be addressed before submitting the other commit,
but I missed the review comments.
Fixes: fd6bbda9c7 ("drm/i915: Pass crtc_state and connector_state to encoder functions")
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471961888-10771-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[mlankhorst: Fix extra whitespace between functions.]
This is mostly code churn, with exception of a few places:
- intel_display.c has changes in intel_sanitize_encoder
- intel_ddi.c has intel_ddi_fdi_disable calling intel_ddi_post_disable,
and required a function change. Also affects intel_display.c
- intel_dp_mst.c passes a NULL crtc_state and conn_state to
intel_ddi_post_disable for shutting down the real encoder.
If we would pass conn_state, then conn_state->connector !=
intel_dig_port->connector and conn_state->best_encoder !=
to_intel_encoder(intel_dig_port).
We also shouldn't pass crtc_state, because in that case the
disabling sequence may potentially be different depending on
which crtc is disabled last. Nice way to introduce bugs.
No other functional changes are done, diff stat is already huge.
Each encoder type will need to be fixed to use the atomic states
separately.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This lets call intel_crt_reset() in contexts where IRQs are disabled and
as such, can't hold the locks required to work with the connectors.
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename
1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko
1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467297225-21379-8-git-send-email-chris@chris-wilson.co.uk
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename
1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko
1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467297225-21379-7-git-send-email-chris@chris-wilson.co.uk
