commit ceed9038b2 upstream.
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c30ae8398 upstream.
The previous commit 32efcc06d2 ("tcp: export count for rehash attempts")
would mis-account rehashing SNMP and socket stats:
a. During handshake of an active open, only counts the first
SYN timeout
b. After handshake of passive and active open, stop updating
after (roughly) TCP_RETRIES1 recurring RTOs
c. After the socket aborts, over count timeout_rehash by 1
This patch fixes this by checking the rehash result from sk_rethink_txhash.
Fixes: 32efcc06d2 ("tcp: export count for rehash attempts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11a496ee6 upstream.
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
In the test case for kasan_remove_zero_shadow():
shadow_start: 0xffffffb802000000, shadow end: 0xffffffbfbe000000
3-level page table:
PUD_SIZE: 0x40000000 PMD_SIZE: 0x200000 PAGE_SIZE: 4K
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com
Fixes: 0207df4fa1 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d upstream.
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9778448175 upstream.
The allocated page is not released if error occurs in
nvm_submit_io_sync_raw(). __free_page() is moved ealier to avoid
possible memory leak issue.
Fixes: aff3fb18f9 ("lightnvm: move bad block and chunk state logic to core")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db58465f11 upstream.
After the recent actions to convert readpages aops to readahead, the
NULL checks of readpages aops in cachefiles_read_or_alloc_page() may
hit falsely. More badly, it's an ASSERT() call, and this panics.
Drop the superfluous NULL checks for fixing this regression.
[DH: Note that cachefiles never actually used readpages, so this check was
never actually necessary]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208883
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1175245
Fixes: 9ae326a690 ("CacheFiles: A cache that backs onto a mounted filesystem")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0732168f upstream.
Properly unwind step by step using refactored helpers from nvme_unmap_data
to avoid a potential double dma_unmap on a mapping failure.
Fixes: 7fe07d14f7 ("nvme-pci: merge nvme_free_iod into nvme_unmap_data")
Reported-by: Marc Orr <marcorr@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9275c206f8 upstream.
Split out three helpers from nvme_unmap_data that will allow finer grained
unwinding from nvme_map_data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a2e94b3f upstream.
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92a5e1fdb2 upstream.
Since main() does not return a value explicitly, the
return values from FAIL_IF() conditions are ignored
and the tests can still pass irrespective of failures.
This makes sure that we always explicitly return the
correct test exit status.
Fixes: 1addb64447 ("selftests/powerpc: Add test for execute-disabled pkeys")
Fixes: c27f2fd170 ("selftests/powerpc: Add test for pkey siginfo verification")
Reported-by: Eirik Fuller <efuller@redhat.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210118093145.10134-1-sandipan@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe04367d upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a9 (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7ba6cfabc upstream.
In rvu_mbox_handler_cgx_mac_addr_get()
and rvu_mbox_handler_cgx_mac_addr_set(),
the msg is expected only from PFs that are mapped to CGX LMACs.
It should be checked before mapping,
so we add the is_cgx_config_permitted() in the functions.
Fixes: 96be2e0da8 ("octeontx2-af: Support for MAC address filters in CGX")
Signed-off-by: Yingjie Wang <wangyingjie55@126.com>
Reviewed-by: Geetha sowjanya<gakula@marvell.com>
Link: https://lore.kernel.org/r/1610719804-35230-1-git-send-email-wangyingjie55@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c25af2502 upstream.
The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.
snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.
Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.
To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.
In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.
BugLink: https://github.com/thesofproject/linux/issues/2646
Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes: 6c63c954e1 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477a538c1 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed7
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes: d8902adcc1 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3c95d0bdb upstream.
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bf ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit d276e16702)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fc7c1ef37 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-watch.c: In function ‘main’:
gpio-watch.c:89:30: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
89 | printf("line %u: %s at %llu\n",
| ~~~^
| |
| long long unsigned int
| %lu
90 | chg.info.offset, event, chg.timestamp_ns);
| ~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 33f0c47b8f ("tools: gpio: implement gpio-watch")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fe7c2f994 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-event-mon.c:110:37: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
110 | fprintf(stdout, "GPIO EVENT at %llu on line %d (%d|%d) ",
| ~~~^
| |
| long long unsigned int
| %lu
111 | event.timestamp_ns, event.offset, event.line_seqno,
| ~~~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes: 03fd11b033 ("tools/gpio/gpio-event-mon: fix warning")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fb upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3f ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c96adff956 upstream.
fl_set_enc_opt() simply checks if there are still bytes left to parse,
but this is not sufficent as syzbot seems to be able to generate
malformatted netlink messages. nla_ok() is more strict so should be
used to validate the next nlattr here.
And nla_validate_nested_deprecated() has less strict check too, it is
probably too late to switch to the strict version, but we can just
call nla_ok() too after it.
Reported-and-tested-by: syzbot+2624e3778b18fc497c92@syzkaller.appspotmail.com
Fixes: 0a6e77784f ("net/sched: allow flower to match tunnel options")
Fixes: 79b1011cb3 ("net: sched: allow flower to match erspan options")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20210115185024.72298-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76e2fc63ca upstream.
Set the maximum DIE per package variable on AMD using the
NodesPerProcessor topology value. This will be used by RAPL, among
others, to determine the maximum number of DIEs on the system in order
to do per-DIE manipulations.
[ bp: Productize into a proper patch. ]
Fixes: 028c221ed1 ("x86/CPU/AMD: Save AMD NodeId as cpu_die_id")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Reported-by: Rafael Kitover <rkitover@gmail.com>
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Tested-by: Rafael Kitover <rkitover@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210939
Link: https://lkml.kernel.org/r/20210106112106.GE5729@zn.tnic
Link: https://lkml.kernel.org/r/20210111101455.1194-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e634efd85 upstream.
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1cf435e2 upstream.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e020ff611b upstream.
The device link device's name was of the form:
<supplier-dev-name>--<consumer-dev-name>
This can cause name collision as reported here [1] as device names are
not globally unique. Since device names have to be unique within the
bus/class, add the bus/class name as a prefix to the device names used to
construct the device link device name.
So the devuce link device's name will be of the form:
<supplier-bus-name>:<supplier-dev-name>--<consumer-bus-name>:<consumer-dev-name>
[1] - https://lore.kernel.org/lkml/20201229033440.32142-1-michael@walle.cc/
Fixes: 287905e68d ("driver core: Expose device link details in sysfs")
Cc: stable@vger.kernel.org
Reported-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210110175408.1465657-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0243bbd5d upstream.
There will be memory leak if driver probe failed. Trace as below:
backtrace:
[<000000002415258f>] kmemleak_alloc+0x3c/0x50
[<00000000f447ebe4>] __kmalloc+0x208/0x530
[<0000000048bc7b3a>] of_dma_get_range+0xe4/0x1b0
[<0000000041e39065>] of_dma_configure_id+0x58/0x27c
[<000000006356866a>] platform_dma_configure+0x2c/0x40
......
[<000000000afcf9b5>] ret_from_fork+0x10/0x3c
This issue is introduced by commit e0d072782c73("dma-mapping:
introduce DMA range map, supplanting dma_pfn_offset "). It doesn't
free dma_range_map when driver probe failed and cause above
memory leak. So, add code to free it in error path.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset ")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210105070927.14968-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7e0c3c29 upstream.
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 576667bad3 upstream.
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ef02b846e upstream.
The cdns3 core device is populated by calling of_platform_populate,
the flag OF_POPULATED is set for core device node, if this flag
is not cleared, when calling of_platform_populate the second time
after loading parent module again, the OF code will not try to create
platform device for core device.
To fix it, it uses of_platform_depopulate to depopulate the core
device which the parent created, and the flag OF_POPULATED for
core device node will be cleared accordingly.
Cc: <stable@vger.kernel.org>
Fixes: 1e056efab9 ("usb: cdns3: add NXP imx8qm glue layer")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef02684c4e upstream.
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6aa61d81 upstream.
Commit c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds
bug") messed up the way dummy-hcd handles requests to turn on the
RESET port feature (I didn't notice that the original switch case
ended with a fallthrough). The call to set_link_state() was
inadvertently removed, as was the code to set the USB_PORT_STAT_RESET
flag when the speed is USB2.
In addition, the original code never checked whether the port was
connected before handling the port-reset request. There was a check
for the port being powered, but it was removed by that commit! In
practice this doesn't matter much because the kernel doesn't try to
reset disconnected ports, but it's still bad form.
This patch fixes these problems by changing the fallthrough to break,
adding back in the missing set_link_state() call, setting the
port-reset status flag, adding a port-is-connected test, and removing
a redundant assignment statement.
Fixes: c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug")
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210113194510.GA1290698@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e0dcf62ab upstream.
The vhub engine has two dma mode, one is descriptor list, another
is single stage DMA. Each mode has different stop register setting.
Descriptor list operation (bit2) : 0 disable reset, 1: enable reset
Single mode operation (bit0) : 0 : disable, 1: enable
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210108081238.10199-2-ryan_chen@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 643a4df7fe upstream.
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 280a9045bb upstream.
According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever
USBCMD.RS=1.
However, it is a good practice to wait some time after setting USBCMD.RS
(approximately 100ms) until USBSTS.HCHalted become zero.
Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs
(see BugLink).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugene Korenevsky <ekorenevsky@astralinux.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210110173609.GA17313@himera.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ca955b5a upstream.
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 927633a6d2 upstream.
In stm_heartbeat_init(): return value gets reset after the first
iteration by stm_source_register_device(), so allocation failures
after that will, after a clean up, return success. Fix that.
Fixes: 1192918530 ("stm class: Add heartbeat stm source device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hui <john.wanghui@huawei.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20210115195917.3184-2-alexander.shishkin@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a173346bd upstream.
Sockets and other non-regular files may actually expect short reads to
happen, don't retry reads for them. Because non-reg files don't set
FMODE_BUF_RASYNC and so it won't do second/retry do_read, we can filter
out those cases after first do_read() attempt with ret>0.
Cc: stable@vger.kernel.org # 5.9+
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 607ec89ed1 upstream.
IORING_OP_CLOSE is special in terms of cancelation, since it has an
intermediate state where we've removed the file descriptor but hasn't
closed the file yet. For that reason, it's currently marked with
IO_WQ_WORK_NO_CANCEL to prevent cancelation. This ensures that the op
is always run even if canceled, to prevent leaving us with a live file
but an fd that is gone. However, with SQPOLL, since a cancel request
doesn't carry any resources on behalf of the request being canceled, if
we cancel before any of the close op has been run, we can end up with
io-wq not having the ->files assigned. This can result in the following
oops reported by Joseph:
BUG: kernel NULL pointer dereference, address: 00000000000000d8
PGD 800000010b76f067 P4D 800000010b76f067 PUD 10b462067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 1788 Comm: io_uring-sq Not tainted 5.11.0-rc4 #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__lock_acquire+0x19d/0x18c0
Code: 00 00 8b 1d fd 56 dd 08 85 db 0f 85 43 05 00 00 48 c7 c6 98 7b 95 82 48 c7 c7 57 96 93 82 e8 9a bc f5 ff 0f 0b e9 2b 05 00 00 <48> 81 3f c0 ca 67 8a b8 00 00 00 00 41 0f 45 c0 89 04 24 e9 81 fe
RSP: 0018:ffffc90001933828 EFLAGS: 00010002
RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000000000d8
RBP: 0000000000000246 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff888106e8a140 R15: 00000000000000d8
FS: 0000000000000000(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000d8 CR3: 0000000106efa004 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
lock_acquire+0x31a/0x440
? close_fd_get_file+0x39/0x160
? __lock_acquire+0x647/0x18c0
_raw_spin_lock+0x2c/0x40
? close_fd_get_file+0x39/0x160
close_fd_get_file+0x39/0x160
io_issue_sqe+0x1334/0x14e0
? lock_acquire+0x31a/0x440
? __io_free_req+0xcf/0x2e0
? __io_free_req+0x175/0x2e0
? find_held_lock+0x28/0xb0
? io_wq_submit_work+0x7f/0x240
io_wq_submit_work+0x7f/0x240
io_wq_cancel_cb+0x161/0x580
? io_wqe_wake_worker+0x114/0x360
? io_uring_get_socket+0x40/0x40
io_async_find_and_cancel+0x3b/0x140
io_issue_sqe+0xbe1/0x14e0
? __lock_acquire+0x647/0x18c0
? __io_queue_sqe+0x10b/0x5f0
__io_queue_sqe+0x10b/0x5f0
? io_req_prep+0xdb/0x1150
? mark_held_locks+0x6d/0xb0
? mark_held_locks+0x6d/0xb0
? io_queue_sqe+0x235/0x4b0
io_queue_sqe+0x235/0x4b0
io_submit_sqes+0xd7e/0x12a0
? _raw_spin_unlock_irq+0x24/0x30
? io_sq_thread+0x3ae/0x940
io_sq_thread+0x207/0x940
? do_wait_intr_irq+0xc0/0xc0
? __ia32_sys_io_uring_enter+0x650/0x650
kthread+0x134/0x180
? kthread_create_worker_on_cpu+0x90/0x90
ret_from_fork+0x1f/0x30
Fix this by moving the IO_WQ_WORK_NO_CANCEL until _after_ we've modified
the fdtable. Canceling before this point is totally fine, and running
it in the io-wq context _after_ that point is also fine.
For 5.12, we'll handle this internally and get rid of the no-cancel
flag, as IORING_OP_CLOSE is the only user of it.
Cc: stable@vger.kernel.org
Fixes: b5dba59e0c ("io_uring: add support for IORING_OP_CLOSE")
Reported-by: "Abaci <abaci@linux.alibaba.com>"
Reviewed-and-tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c93cc9e16d upstream.
If we're freeing/finishing iopoll requests, ensure we check if the task
is in idling in terms of cancelation. Otherwise we could end up waiting
forever in __io_uring_task_cancel() if the task has active iopoll
requests that need cancelation.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
