[ Upstream commit ac2917b019 ]
The malidp_mw_connector_helper_funcs is not referenced by name
outside of the file it is in, so make it static to avoid the
following warning:
drivers/gpu/drm/arm/malidp_mw.c:59:41: warning: symbol 'malidp_mw_connector_helper_funcs' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217115309.2133503-1-ben.dooks@codethink.co.uk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c81073909 ]
On the Arm Juno platform, the HDLCD pixel clock is constrained to 250KHz
resolution in order to avoid the tiny System Control Processor spending
aeons trying to calculate exact PLL coefficients. This means that modes
like my oddball 1600x1200 with 130.89MHz clock get rejected since the
rate cannot be matched exactly. In practice, though, this mode works
quite happily with the clock at 131MHz, so let's relax the check to
allow a little bit of slop.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b96151edce ]
Rather than allowing any old mode through, then subsequently refusing
unmatchable clock rates in atomic_check when it's too late to back out
and pick a different mode, let's do that validation up-front where it
will cause unsupported modes to be correctly pruned in the first place.
This also eliminates an issue whereby a perceived clock rate of 0 would
cause atomic disable to fail and prevent the module from being unloaded.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a88e0c148 ]
This patch trying to fix monitor freeze issue caused by drm error
'flip_done timed out' on LS1028A platform. this set try is make a loop
around the second setting CVAL and try like 5 times before giveing up.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When we want to writeback to memory in NV12 format we need to program
the RGB2YUV coefficients. Currently, we don't program the coefficients
and NV12 doesn't work at all.
This patchset fixes that by programming a sane default(bt709, limited
range) as rgb2yuv coefficients.
In the long run, probably we need to think of a way for userspace to
be able to program that, but for now I think this is better than not
working at all or not advertising NV12 as a supported format for
memwrite.
Changes since v1:
- Write the rgb2yuv coefficients only once, since we don't change
them at all, just write them the first time NV12 is programmed,
suggested by Brian Starkey, here [1]
[1] https://lists.freedesktop.org/archives/dri-devel/2018-August/186819.html
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Currently, if userspace calls drm_wait_vblank before the crtc is
activated the crtc vblank_enable hook is called, which in case of
malidp driver triggers some warninngs. This happens because on
device init we don't inform the drm core about the vblank state
by calling drm_crtc_vblank_on/off/reset which together with
drm_vblank_get have some magic that prevents calling drm_vblank_enable
when crtc is off.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The HDLCD engine needs an active plane while the CRTC is active, as
it will start scanning out data from HDLCD_REG_FB_BASE once it gets
enabled. Make sure that the only available plane doesn't get disabled
while the CRTC remains active, as this will scanout invalid data.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The plane cleanup handler currently calls drm_plane_helper_disable(),
which is a legacy helper function. Replace it with a call to
drm_atomic_helper_shutdown() at removal time. The plane .destroy()
handler now consisting only of a call to drm_plane_cleanup(), replace it
with direct calls to that function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The top-level error handler calls drm_mode_config_cleanup() which will
destroy all planes. There's no need to destroy them manually in lower
error handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Replace driver's code with the generic helpers that do the same thing
including the NULL check.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Set possible_clones field to report that the writeback connector and
the one driving the display could be enabled at the same time.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Older version of this patch series reported writeback as disconnected
to avoid confusing userspace not aware of writeback connectors.
However, the version that got merged uses a special cap
(DRM_CLIENT_CAP_WRITEBACK_CONNECTORS) for this purpose.
This helps us avoid some special handling of writeback connector
in drm_helper_probe_single_connector_modes, see [1].
https://lists.freedesktop.org/archives/dri-devel/2018-July/183144.html
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
"mali-dp driver changes for drm-next, includes the driver implementation
for writeback, improvements for power management handling in the driver
and a debugfs entry for reporting possible internal errors. Please pull
at your earliest convenience.
Boris Brezillon is also interested in this pull as he is going to change
slightly the parameter for the writeback connector's atomic_commit() and
he needs to fix the mali-dp driver in his series."
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705144408.GH15340@e110455-lin.cambridge.arm.com
malidp_pm_suspend_late checks if the runtime status is not suspended
and if so, invokes malidp_runtime_pm_suspend which disables the
display engine/core interrupts and the clocks. It sets the runtime status
as suspended.
The difference between suspend() and suspend_late() is as follows:-
1. suspend() makes the device quiescent. In our case, we invoke the DRM
helper which disables the CRTC. This would have invoked runtime pm
suspend but the system suspend process disables runtime pm.
2. suspend_late() It continues the suspend operations of the drm device
which was started by suspend(). In our case, it performs the same functionality
as runtime_suspend().
The complimentary functions are resume() and resume_early(). In the case of
resume_early(), we invoke malidp_runtime_pm_resume() which enables the clocks
and the interrupts. It sets the runtime status as active. If the device was
in runtime suspend mode before system suspend was called, pm_runtime_work()
will put the device back in runtime suspended mode( after the complete system
has been resumed).
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
One needs to store the value of the OUTPUT_DEPTH that one has parsed from
device tree, so that it can be restored on system resume. This value is
set in the modeset function as this gets reset when the system suspends.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Display and scaling engine interrupts need to be disabled when the
runtime pm invokes malidp_runtime_pm_suspend(). Conversely, they
need to be enabled in malidp_runtime_pm_resume().
This patch depends on:
https://lkml.org/lkml/2017/5/15/695
Reported-by: Alexandru-Cosmin Gheorghe <Alexandru-Cosmin.Gheorghe@arm.com>
Signed-off-by: Alexandru-Cosmin Gheorghe <Alexandru-Cosmin.Gheorghe@arm.com>
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Malidp uses two interrupts ie 1. se_irq - used for memory writeback.
and 2. de_irq - used for display output.
Extract the hardware initialization part from malidp interrupt registration
ie (malidp_de_irq_init()/ malidp_se_irq_init()) into a separate function
(ie malidp_de_irq_hw_init()/malidp_se_irq_hw_init())
which will be later invoked from runtime_pm_resume function when it needs
to re-enable the interrupts.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Malidp uses two interrupts ie 1. se_irq - used for memory writeback.
and 2. de_irq - used for display output.
'struct drm_device' is being replaced with 'struct malidp_hw_device'
as the function argument. The reason being the dependency of
malidp_de_irq_fini on 'struct drm_device' needs to be removed so as to
enable it to call from functions which receives 'struct malidp_hw_device'
as argument. Furthermore, there is no way to retrieve 'struct drm_device'
from 'struct malidp_hw_device'.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Status register contains a lot of bits for reporting internal errors
inside Mali DP. Currently, we just silently ignore all of the errors,
that doesn't help when we are investigating different bugs, especially
on the FPGA models which have a lot of constraints, so we could easily
end up in AXI or underrun errors.
Add a new file called debug that contains an aggregate of the
errors reported by the Mali DP hardware.
E.g:
[root@alarm ~]# cat /sys/kernel/debug/dri/1/debug
[DE] num_errors : 167
[DE] last_error_status : 0x00000001
[DE] last_error_vblank : 385
[SE] num_errors : 3
[SE] last_error_status : 0x00e23001
[SE] last_error_vblank : 201
Changes since v2:
- Add lock to protect the errors stats.
- Add possibility to reset the error stats by writing anything to the
debug file.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 operates in continuous writeback mode (writes frame content
until stopped) and it needs special handling in order to behave like
a one-shot writeback engine. The original state machine added for DP500
was a bit fragile, as it did not handle correctly cases where a new
atomic commit was in progress when the SE IRQ happens and it would
commit some partial updates.
Improve the handling by adding a parameter to the set_config_valid()
function to clear the config valid bit in hardware before starting a
new commit and by introducing a MW_RESTART state in the writeback
state machine to cater for the case where a new writeback commit
gets submitted while the last one is still being active.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP has a memory writeback engine which can be used to write the
composition result to a memory buffer. Expose this functionality as a
DRM writeback connector on supported hardware.
Changes since v1:
Daniel Vetter:
- Don't require a modeset when writeback routing changes
- Make writeback connector always disconnected
Changes since v2:
- Rebase onto new drm_writeback_connector
- Add reset callback, allocating subclassed state
Daniel Vetter:
- Squash out-fence support into this commit
Gustavo Padovan:
- Don't signal fence directly from driver (and drop malidp_mw_job)
Changes since v3:
- Modifications to fit with Mali-DP commit tail changes
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Annotate the pixel format matrix for DP500 with the memory-write flag
for formats that are supported by the SE memwrite engine.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Add a layer bit for the SE memory-write, and add it to the pixel format
matrix for DP550/DP650.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP display processors are able to write the composition result to a
memory buffer via the SE.
Add entry points in the HAL for enabling/disabling this feature, and
implement support for it on DP650 and DP550. DP500 acts differently and
so is omitted from this change.
Changes since v3:
- Fix missing vsync interrupt for DP550
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
In commits:
34a2ab5e06 ("drm: Add acquire ctx parameter to ->update_plane")
1931529448 ("drm: Add acquire ctx parameter to ->plane_disable")
a pointer to a drm_modeset_acquire_ctx structure was added as an
argument to the method prototypes. The transitional helpers are
supposed to be directly plugged in as implementations of these
methods, but doing so generates a warning. Add the missing
argument.
A number of buggy users were added for drm_plane_helper_disable()
which need to be fixed up for this change, which we do by passing
a NULL ctx argument.
Fixes: 1931529448 ("drm: Add acquire ctx parameter to ->plane_disable")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/E1fa1Zr-0005gT-VF@rmk-PC.armlinux.org.uk
The width and height needs to be swapped
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[rebased on top of v4.18-rc1]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
On some Mali-DP processors, the LAYER_FORMAT register contains fields
other than the format. These bits were unconditionally cleared when
setting the pixel format, whereas they should be preserved at their
reset values.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Internally Mali DP uses an RGB pipeline so video layers that support
YUV input buffers need to convert the input data to RGB. The YUV
buffers can have various encodings and this patch introduces support
for BT.601, BT.709 and BT.2020 encodings, both limited and full ranges.
This patch adds support for specifying the color encoding of the
input buffers for the planes that are backed by the video layers
and programs the YUV2RGB coefficients into hardware based on the
selected encoding.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[updated to use standard properties]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
When unbinding the mali-dp driver the drm_vblank_cleanup() function
warns us that the vblanks are still enabled. Fix that by calling
drm_crtc_vblank_off() in the malidp_unbind() function.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The plane cleanup handler currently calls drm_plane_helper_disable(),
which is a legacy helper function. Replace it with a call to
drm_atomic_helper_shutdown() at removal time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The top-level error handler calls drm_mode_config_cleanup() which will
destroy all planes. There's no need to destroy them manually in lower
error handlers.
As plane cleanup is now handled entirely by drm_mode_config_cleanup(),
we must ensure that the plane .destroy() handler frees allocated memory
for the plane object that was freed by malidp_de_planes_destroy(). Do so
by replacing the call to devm_kfree() in the .destroy() handler by
kfree(). devm_kfree() is currently a no-op as the plane memory is
allocated with kzalloc(), not devm_kzalloc().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP hardware has a 'go' bit (config_valid) for making the new scene
parameters active at the next page flip. The problem with the current
code is that the driver first sets this bit and then proceeds to wait
for confirmation from the hardware that the configuration has been
updated before arming the vblank event. As config_valid is actually
asserted by the hardware after the vblank event, during the prefetch
phase, when we get to arming the vblank event we are going to send it
at the next vblank, in effect halving the vblank rate from the userspace
perspective.
Fix it by sending the userspace event from the IRQ handler, when we
handle the config_valid interrupt, which syncs with the time when the
hardware is active with the new parameters.
Reported-by: Alexandru-Cosmin Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali dp needs to disable pixel alpha blending (use layer alpha blending) to
display color formats that do not contain alpha bits per pixel
This patch depends on:
"[PATCH v2 01/19] drm/fourcc: Add a alpha field to drm_format_info"
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the case, when the user wants to scale and rotate a layer by 90/270
degrees, the scaling engine input dimensions' parameters ie width and
height needs to be swapped with respect to the layer's input dimensions.
This means scaling engine input height should be set to layer's input
width and scaling engine input width should be set to
layer's input height.
Signed-off-by: Ayan Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Currently the scaling engine gets enabled for a plane where the input
size differs from the composition size. As rotation is done natively
by the plane's hardware layer, we don't need the scaling engine to be
enabled.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
We use "mc" without initializing it if scaling is not necessary.
Fixes: 28ce675b74 ("drm: mali-dp: Add plane upscaling support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mihail Atanassov <Mihail.Atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP hardware needs pitch line sizes aligned to the bus burst
size for reads, so take that into consideration when allocating dumb
buffers. If the layer is rotated then the stride size requirement is
even larger for some hardware versions, so allocate for the worst case
scenario. Update the ->dumb_create() hook to a driver specific function
that sets the correct pitch size.
Reported-by: Ayan Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Rotated planes need a pitch size that is aligned to 8 bytes
for older DP500 and DP550 and at least 64 bytes for DP650. Replace
the malidp_hw_pitch_valid() function with one that calculates
the correct pitch alignment to take into account rotation.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-5-ville.syrjala@linux.intel.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-4-ville.syrjala@linux.intel.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-20-noralf@tronnes.org
We need to pull 66660d4cf2 (drm: add connector info/property for
non-desktop displays [v2]) into drm-misc-next to continue the development
of the display rotation series.
Effectively this also pulls 4.15-r2 into drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
mali-dp interface cleanups.
* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
drm: mali-dp: Disable planes when their CRTC gets disabled.
drm: mali-dp: Separate static internal data into a read-only structure.
drm/arm: Replace instances of drm_dev_unref with drm_dev_put.
drm: mali-dp: switch to drm_*_get(), drm_*_put() helpers
