This will allow for a platform hda driver to use it as well. It
removes the dependency on the module param from hda_intel, which will
allow for azx_setup_periods to be shared.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The forthcoming platform hda driver needs to override the way
registers are read and written. In preparation for that, introduce a
reg_ops struct that can be implemented differently by the new driver.
Change the existing macros to use the new structure, and move them to
hda_priv.h where they will be accessible to both PCI and platform
drivers.
Start with register access, but later commits will add more ops that
differ between PCI and platform.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Later commits adding support for hda platform drivers will want to use
the same defines and structures. Put them in a place reachable by both
hda_intel and the new platform driver.
This is a mostly a direct copy with a few whitespace and comment
changes to make checkpatch happy.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA spec, we must write 1 to bit 15 on a CORBRP
reset, read back 1, then write 0, then read back 0. This must be
done while the DMA is not running.
We accidentaly ended up writing back the 0 by using a writel
instead of a writew to CORBWP.
This caused occasional controller failure on Bay Trail hardware.
[replaced error messages with dev_err() by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep input device is registered via input_register_device(), but
this is called in snd_hda_attach_beep_device() where the sound devices
aren't registered yet. This leads to the binding to non-existing
object, thus results in failure. And, even if the binding worked
(against the PCI object), it's still racy; the input device appears
before the sound objects.
For fixing this, register the input device properly at dev_register
ops of the codec object it's bound with. Also, call
snd_hda_detach_beep_device() at dev_disconnection so that it's
detached at the right timing. As a bonus, since it's called in the
codec's ops, we can get rid of the further call from the other codec
drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many HP laptops with STAC codecs have a docking station port and BIOS
sets the pins for the input on the dock as a line in. Because the
generic parser doesn't handle a line in pin as auto-switchable, this
resulted in the manual capture source selection on these laptops.
However, from the usability POV, the automatic switching is easier.
This patch adds the line_in_auto_switch hint in the fixup function for
these laptops. Even if no dock port is present, this should be
harmless as the generic parser allows the auto-switching only in a
limited situation (all three pins are located in different
positions).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the controller, the new codec object is assigned as a
parent for the hd-audio beep input devices, just like already done for
PCM and hwdep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
As there are too deep indirections (e.g. ep->chip->dev->dev),
a few new local macros, usb_audio_err() & co, are introduced.
Also, the device numbers in some messages are dropped, as they are
shown in the prefix automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
The debug prints are also reformatted to suit with dev_dbg().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
Some commented debug prints are also enabled as dev_dbg().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
All debug print macros have been replaced with dev_dbg(), too.
Also, added the missing definition of snd_azf3328_ctrl_inw().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
