musb->int_usb already contains the correct
information for musb-core to handle babble.
In fact, this very check was just causing a
nonsensical babble interrupt storm.
With this I can get test.sh to run and, even though
all tests fail with timeout, that's still better
than locking up the system due to IRQ storm.
Also, if I remove g_zero and load g_mass_storage,
then everything works fine again.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when musb is operating as host and a remote wakeup
fires up, a resume interrupt will be raised. At that
point SUSPENDM bit is automatically cleared and
RESUME bit is automatically set.
Remove those two from IRQ handler.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was already a proper place where we were
checking for babble interrupts, move babble
recovery there.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if reset fails, we should return a *negative*
error code, not a positive value.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
FSDEV is set for both HIGH and FULL speeds,
the correct HIGHSPEED check is done through
power register's HSMODE bit.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devctl & MUSB_DEVCTL_HM represents a single bit,
just check for the bit, there's really no need
to compare the result against 0.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent bug fix I did that was marked for stable backports
introduced a slightly wrong dependency on CONFIG_OMAP_CONTROL_PHY.
I was missing the fact that the PHY driver already stubs out the
omap_control_usb_set_mode, and we only need to add a dependency
to prevent the musb-omap2430 driver from being built-in when
the phy driver is a loadable module, but we should not prevent it
from being built altogether when the phy driver is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36c ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Acked-by: Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of using manually spelled out bit-shits
and iterate over each of the 16-bits (one for
each endpoint) on each direction, we can make use
of for_each_set_bit() which internally uses
find_first_bit().
This makes the code slightly more readable while
also making we only iterate over bits which are
actually set.
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.
This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().
This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable HCD_BH flag for musb host controller driver.
This improves the MSC/UVC through put. With this enabled
even 640x480@30fps webcam streaming is also supported.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The commit 889ad3b "usb: musb: try a race-free wakeup" breaks device
hotplug enumeraitonn when the device is connected behind a hub while usb
autosuspend is enabled.
Adding finish_resume_work into runtime resume callback fixes the issue.
Also resume root hub is required to resume the bus from runtime suspend,
so move musb_host_resume_root_hub() back to its original location, where
handles RESUME interrupt.
Signed-off-by: Bin Liu <b-liu@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
bfin_remove() is not (nor should it be) marked as __exit, so we should
not be using __exit_p() wrapper with it, otherwise unbinding through
sysfs does not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The omap musb front-end calls into the phy driver directly
instead of using a generic phy interface, which causes a link
error when the specific driver is not built-in:
drivers/built-in.o: In function `omap2430_musb_disable':
usb/musb/omap2430.c:480: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap2430_musb_enable':
usb/musb/omap2430.c:466: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:447: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap_musb_set_mailbox':
usb/musb/omap2430.c:273: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:304: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o:(.debug_addr+0xbd9e0): more undefined references to `omap_control_usb_set_mode' follow
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36c ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple musb glue drivers depend on the generic usb phy support,
but fail to list it as a dependency in Kconfig. This results
in build erros like:
drivers/built-in.o: In function `am35x_remove':
:(.text+0xadacc): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `am35x_probe':
:(.text+0xae1c8): undefined reference to `usb_phy_generic_register'
:(.text+0xae244): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_remove':
:(.text+0xaf648): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_musb_init':
:(.text+0xaf694): undefined reference to `usb_phy_generic_register'
This adds the ones that are missing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1. set AUTOREQ to NONE at the beginning of teardown;
2. add delay for dma pipeline to drain;
3. Do not set USB_TDOWN bit for RX teardown.
The CPPI hw has an issue that when tearing down a RX channel, if
another RX channel is receiving data, the CPPI will lockup.
To workaround the issue, do not set the CPPI TD bit. The steps before
this point ensures the CPPI channel will be torn down properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The macro EP_MODE_AUTOREG_* should be called EP_MODE_AUTOREQ_*, as they
are used for register AUTOREQ.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While the code is correct and functions well, it's still
a bit misleading to add the reference operator in from of
the buf argument.
This patch simply removes that operator in order to make
use of buf slightly better to the eyes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
since the split of host+gadget mode in commit 74c2e93600 ("usb: musb:
factor out hcd initalization") we leak the usb_hcd struct. We call now
musb_host_cleanup() which does basically usb_remove_hcd() and also sets
the hcd variable to NULL. Doing so makes the finall call to
musb_host_free() basically a nop and the usb_hcd remains around for ever
without anowner.
This patch drops that NULL assignment for that reason.
Fixes: 74c2e93600 ("usb: musb: factor out hcd initalization")
Cc: <stable@vger.kernel.org> # v3.11+
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 82c02f58ba ("usb: musb: Allow multiple glue layers to be
built in") enabled selecting multiple glue layers, which in turn
exposed things more for randconfig builds. If NOP_USB_XCEIV is
built-in and TUSB6010 is a loadable module, we will get:
drivers/built-in.o: In function `tusb_remove':
tusb6010.c:(.text+0x16a817): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `tusb_probe':
tusb6010.c:(.text+0x16b24e): undefined reference to `usb_phy_generic_register'
make: *** [vmlinux] Error 1
Let's fix this the same way as commit 70c1ff4b3c ("usb: musb:
tusb-dma can't be built-in if tusb is not").
And while at it, let's not allow selecting the glue layers except
on platforms really using them unless COMPILE_TEST is specified:
- TUSB6010 is in practise only used on omaps
- DSPS is only used on TI platforms
- UX500 is only used on STE platforms
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
!strncmp(buf, "force host", 9) is true if and only if buf starts with
"force hos". This was obviously not what was intended. The same error
exists for "force full-speed", "force high-speed" and "test
packet". Using strstarts avoids the error-prone hardcoding of the
prefix length.
For consistency, also change the other occurences of the !strncmp
idiom.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit cc92f681 (usb: musb: Populate new IO
functions for blackfin) added a typo which
prevented MUSB's blackfin glue layer from being
built. Due to lack of tests and compilers for
that architecture, the typo ended up being
merged and causing a build regression.
Fix that here
Cc: Tony Lindgren <tony@atomide.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Blackfin's MUSB implementation lacks a bunch of
registers which they end up not defining a macro
for. In order to avoid build breaks, let's ifdef
out some of the registers from our regdump debugfs
utility so that we don't try to use those on
Blackfin builds.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This removes the ifdef clutter a bit and saves few lines.
It also makes it easier to detect the remaining places
where we have conditional building of code done based
on if defined for things like DMA.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no reason any longer to keep it as a choice now that
the IO access has been fixed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows the endpoints to work when multiple MUSB glue
layers are built in.
Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change to use new IO access. This allows us to build in multiple
MUSB glue layers.
[ balbi@ti.com : switch to EXPORT_SYMBOL_GPL()
fix long lines ]
Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate new IO functions for blackfin
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Let's populate the new IO functions for tusb6010 but not use
them yet.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
MUSB currently breaks badly if we try to build in support
for multiple platforms. This also happens if done as loadable
modules, which is not nice for distros.
Let's fix the issue by adding new struct musb_io for the IO
access functions that the platform code can populate. Note
that we don't want to use the current ops as that's really
platform_data and and set as a const.
This should allow eventually adding function pointers also
for the DMA code to struct musb_io, but that's a whole
different set of patches. For now, let's just fix the PIO
access.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable the MUSB interrupts till MUSB is recovered fully from BABBLE
condition. There are chances that we could get multiple interrupts
till the time the babble recover work gets scheduled. Sometimes
this could even end up in an endless loop making MUSB itself unusable.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a poll loop for max 25us for HS devices. Now guess what, I
tested it in gadget mode and forgot about the little detail. Nobody seem
to have it noticed…
This patch adds the missing logic for hostmode so it is recognized in
host and device mode properly.
Fixes: 50aea6fca7 ("usb: musb: cppi41: fire hrtimer according to
programmed channel length")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb registers can be dumped using the file regdump
which is created in debugfs. Up to now hard coded
register addresses are used for that. Different glue
layers however have different register addresses. The
patch addresses this issue by substituting bare register
addresses with defines.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On am335x-evm with musb in host mode and using it as a wakeup source the
following happens once the CPU comes out of suspend to ram:
|PM: Wakeup source MPU_WAKE
|PM: noirq resume of devices complete after 15.453 msecs
|PM: early resume of devices complete after 2.222 msecs
|PM: resume of devices complete after 507.351 msecs
|Restarting tasks ...
|------------[ cut here ]------------
|WARNING: CPU: 0 PID: 322 at drivers/usb/core/urb.c:339 usb_submit_urb+0x494/0x4c8()
|URB cc0db380 submitted while active
|[<c0348e64>] (usb_submit_urb) from [<c0340f94>] (hub_activate+0x2b8/0x49c)
|[<c0340f94>] (hub_activate) from [<c03411dc>] (hub_resume+0x14/0x1c)
|[<c03411dc>] (hub_resume) from [<c034be10>] (usb_resume_interface.isra.4+0xdc/0x110)
|[<c034be10>] (usb_resume_interface.isra.4) from [<c034beb0>] (usb_resume_both+0x6c/0x13c)
|[<c034beb0>] (usb_resume_both) from [<c034cca4>] (usb_runtime_resume+0x10/0x14)
|[<c034cca4>] (usb_runtime_resume) from [<c02bbd80>] (__rpm_callback+0x2c/0x60)
|[<c02bbd80>] (__rpm_callback) from [<c02bbdd4>] (rpm_callback+0x20/0x74)
|[<c02bbdd4>] (rpm_callback) from [<c02bcc48>] (rpm_resume+0x380/0x548)
|[<c02bcc48>] (rpm_resume) from [<c02bcb00>] (rpm_resume+0x238/0x548)
|[<c02bcb00>] (rpm_resume) from [<c02bd08c>] (__pm_runtime_resume+0x64/0x94)
|[<c02bd08c>] (__pm_runtime_resume) from [<c034b5a4>] (usb_autopm_get_interface+0x18/0x5c)
|[<c034b5a4>] (usb_autopm_get_interface) from [<c03438b8>] (hub_thread+0x10c/0x115c)
|[<c03438b8>] (hub_thread) from [<c005a70c>] (kthread+0xbc/0xd8)
|---[ end trace 036aa5fe78203142 ]---
|hub 1-0:1.0: activate --> -16
|hub 2-0:1.0: activate --> -16
The reason for this backtrace is the attempt of the USB code to resume
the HUB twice and thus enqueue the status URB twice.
Alan Stern was a great help by explaining how the USB code supposed to
work and what is most likely the problem. The root problem is that after
resume the musb runtime-suspend state remains RPM_SUSPENDED.
According to git log it RPM was added for the omap2430 platform. If I
understand it correct the omap2430 invokes a get on musb once a cable is
connected and a put once the cable is gone. In between the device could
go auto-idle/off. Not sure what happens when the device goes into suspend
but then I guess it was gadget only.
On DSPS I see only a get in probe and put in remove function. This would
forbid RPM from working but then the devices enterns suspended state
anyway :)
To get rid of this warning, I set the device state to RPM_ACTIVE which
the expected state.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Attaching a keyboard, using it as a wakeup via
|for f in $(find /sys/devices/ocp.3/47400000.usb -name wakeup)
|do
| echo enabled > $f
|done
going into standby
| echo standby > /sys/power/state
and now a wake up by a pressing a key.
What happens is that the system wakes up but the USB device is dead. The
USB stack tries to send a few control URBs but nothing comes back.
Eventually it gaves up and the device remains dead:
|[ 632.559678] PM: Wakeup source USB1_PHY
|[ 632.581074] PM: noirq resume of devices complete after 21.261 msecs
|[ 632.607521] PM: early resume of devices complete after 10.360 msecs
|[ 632.616854] net eth2: initializing cpsw version 1.12 (0)
|[ 632.704126] net eth2: phy found : id is : 0x4dd074
|[ 636.704048] libphy: 4a101000.mdio:00 - Link is Up - 1000/Full
|[ 638.444620] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 653.713435] usb 1-1: device descriptor read/64, error -110
|[ 669.093435] usb 1-1: device descriptor read/64, error -110
|[ 669.473424] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 684.743436] usb 1-1: device descriptor read/64, error -110
|[ 690.065097] PM: resume of devices complete after 57450.744 msecs
|[ 690.076601] PM: Finishing wakeup.
|[ 690.076627] Restarting tasks ...
It seems that since we got woken up via MUSB_INTR_RESUME the
musb_host_finish_resume() callback is executed before the
resume-callbacks of the PHY and glue layer are invoked. If I delay it
until the glue layer resumed then I don't see this problem.
I also move musb_host_resume_root_hub() into that callback since I don't
see any reason in doing anything resume-link if there are still pieces
not restored.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The am335x-evmsk support two kinds of suspend:
- standby
the USB device remains powered while the system goes into suspend
- mem
the USB device becomes powerless while the system goes into suspend.
In the "standby" case the device resumes quickly. In the "mem" case the
system hangs for a few seconds. It seems to me that the USB-device has
no address (it was disconnected) and the USB stack thinks that it is
fully operational and GetPortStatus returns the status from before the
suspend so it is not a big help here.
This adds a check in the resume path to see if the device mode (A or B)
and the speed is the same. If the device went missing between
suspend/resume (VBUS went down) then MUSB seems to go into B mode and
HS/FS bits are cleared. In that case we clear the port1_status bits and
assume a disconnect. Once the stack learns this it does a "logical
disconnect" and removes the USB-device quickly. Should the device remain
connected during the suspend then MUSB will receives a "CONNECT" interrupt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 0ec8fd70fb ("USB: musb: fix possible panic while resuming")
musb_resume() became musb_resume_early() in order to enable the clocks
early on resume. This piece of the resume code was removed later in
commit 034917612 ("usb: musb: move clock handling to glue layer").
In between the function was renamed from musb_resume_early() to
musb_resume_noirq() by commit commit 48fea9659e ("USB: Rework musb
suspend()/resume_early()").
Now I see that first musb_core is resumed followed by phy and glue
layer and I ask myself is this really what we intend to do? This kind
of revoked the purpose of the first commit (0ec8fd70fb).
Because of this and because it looks wrong to resume (core) before the
glue layer I push it to the ->resume callback.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP2+ MUSB glue layer still uses a bare number for the DEVCTL.B-Device bit
in one place, while there's #define MUSB_DEVCTL_BDEVICE for that.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
future patches will remove the extra 'driver'
argument to ->udc_stop(), in order to do that,
we must make sure that our UDC does not rely
on it first.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The drivers should use dmaengine_terminate_all() or dmaengine_slave_config()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in
|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
echo mem > /sys/power/state
then you go boom
|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)
because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 468bcc2a2c ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a2c "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit c58d80f52 ("usb: musb: Ensure that cppi41 timer gets armed on
premature DMA TX irq") fixed hrtimer scheduling bug. There is one left
which does not trigger that often.
The following scenario is still possible:
lock(&x->lock);
hrtimer_start(&x->t);
unlock(&x->lock);
expires:
t->function();
lock(&x->lock);
lock(&x->lock); if (!hrtimer_queued(&x->t))
hrtimer_start(&x->t);
unlock(&x->lock);
if (!list_empty(x->early_tx_list))
ret = HRTIMER_RESTART;
-> hrtimer_forward_now(...)
} else
ret = HRTIMER_NORESTART;
unlock(&x->lock);
and the timer callback returns HRTIMER_RESTART for an armed timer. This
is wrong and we run into the BUG_ON() in __run_hrtimer().
This can happens on SMP or PREEMPT-RT.
The patch fixes the problem by only starting the timer if the timer is
not yet queued.
Cc: stable@vger.kernel.org
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: collected information and created a patch + description based
on it]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
Intensive tests with USB audio devices connected to a musb host port
have shown reproducible pops and clicks in both the playback and the
capture stream.
These are related to how the early_tx hrtimer is set up, and it turns
out they can be fixed by reducing the timer's slack value from 40 to
25 us. Also, when the callback is ran without taking action, it should
be rescheduled 20 us later instead of 50 us.
Reported-and-tested-by: Sven Neumann <neumann@teufel.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.
The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.
Validated using the following usbtest write case in MUSB host mode.
# testusb -t1 -c1
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.
Babble control register logic is implemented in the latest
revision of AM335x.
Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for musb_platform_reset().
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During babble condition both first disconnect of devices are
initiated. Make sure MUSB controller is reset and re-initialized
after all disconnects.
To acheive this schedule a delayed work for babble recovery.
While at that convert udelay to usleep_range.
Refer Documentation/timers/timers-howto.txt
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.
Handle babble condition iff MUSB is in HOST mode.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following the name change of the NOP transceiver driver in commit
4525bee (usb: phy: rename usb_nop_xceiv to usb_phy_generic), the
transceiver driver was no longer operable under its old name.
Register the transceiver driver before calling usb_get_phy() to make
sure we are noticed by an error message if it is not available.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481d8, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.
Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.
Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.
Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.
With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 1af54b7a4.
The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.
Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.
The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before accessing any of an endpoint's CSR registers, make sure the
correct endpoint is selected. Otherwise, data read from or written to
the registers is likely to affect the wrong endpoint as long as the
connected device has more than one endpoint.
This, of course, leads to all sorts of strange effects such as stream
starvation and driver internal state machine confusion due to spurious
interrupts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/cppi41 glue layer is capable of handling transactions that span
over more than one USB packet by reloading the DMA descriptors
partially. An urb is considered completed when either its transfer
buffer has been filled entirely (actual_length ==
transfer_buffer_length) or if a packet in the stream has less bytes than
the endpoint's wMaxPacketSize.
Once one of the above conditions is met, musb_dma_completion() is called
from cppi41_trans_done(). However, the final decision whether or not to
return the urb to its owner is made by the core and its determination of
the variable 'done' in musb_host_rx(). This code has currently no way of
knowing what the size of the last packet was, and whether or not to
give back the urb due to a short read.
Fix this by introducing a new boolean flag in 'struct dma_channel', and
set it from musb_cppi41.c. If set, it will make the core do what the
DMA layer decided and complete the urb.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The datasheet says that MUSB_TXCSR_FLUSHFIFO is only valid when
MUSB_TXCSR_TXPKTRDY is set as well.
With this patch applied, the warning in this function does no longer
kick in when an USB soundcard is unplugged while the stream is active.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On AM33xx platforms, unplugging a device in the middle of an active
transfer leads to a drop of MUSB_DEVCTL_HM in MUSB_DEVCTL before the
system is informed about a disconnect. This consequently makes the musb
core call the gadget code to handle the interrupt request, which then
crashes the kernel because the relevant pointers haven't been set up
for gadget mode.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
in musb_interrupt() and musb_dma_completion() to detect whether the
controller is in host or peripheral mode. This information is provided
by the driver logic and does not rely on register contents.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a little cleanup that removes unnecessary casts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 943c13971c "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For DSPS platform usb_phy_vbus(_off/_on) are NOPs.
So during musb_platform_reset() call usb_phy(_shutdown/_init)
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and err2 and err3 renamed.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and linux/device.h is
added to make sure the devm_*() routine declarations are unambiguously
available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and clk_get is replaced by it
corresponding devm version and the clk_puts are done away with. The
labels are renamed to make them ordered.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces the use of managed interfaces for clk_get and
kzalloc and removes the corresponding free function calls in the probe
and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no reason for the register accessor functions not to adhere
to the CodingStyle rules.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:
CPU 0 CPU1
start_next_transfer(RQ1);
DMA interrupt
if (premature_irq(RQ1))
if (!hrtimer_active(timer))
hrtimer_start(timer);
hrtimer expires
timer->state = CALLBACK_RUNNING;
timer->fn()
cppi41_recheck_tx_req()
complete_request(RQ1);
if (requests_pending())
start_next_transfer(RQ2);
DMA interrupt
if (premature_irq(RQ2))
if (!hrtimer_active(timer))
hrtimer_start(timer);
timer->state = INACTIVE;
The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:
timer->state != HRTIMER_STATE_INACTIVE
which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.
That's clearly documented:
* A timer is active, when it is enqueued into the rbtree or the
* callback function is running or it's in the state of being migrated
* to another cpu.
But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.
We have a helper function for this: hrtimer_is_queued(). This
evaluates:
timer->state & HRTIMER_STATE_QUEUED
So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().
Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
