Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are handled by the protocol layer and
consequently the mmc_suspend|resume_host APIs are marked as deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are handled by the protocol layer and
consequently the mmc_suspend|resume_host APIs are marked as deprecated.
While moving away from using the deprecated APIs, there are nothing
left to be done for the suspend and resume callbacks, so remove them.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Additionally, remove dead code which also used the deprecated APIs.
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are handled by the protocol layer and
consequently the mmc_suspend|resume_host APIs are marked as deprecated.
While moving away from using the deprecated APIs, there are nothing
left to be done for the suspend and resume callbacks, so remove them.
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We want to give user space provision to fully consume a card
insert/remove event, when the event was caused by a wakeup irq.
By signaling the wakeup event for a time of 5 s for devices configured
as wakeup capable, we likely will be prevent a sleep long enough to let
user space consume the event.
To enable this feature, host drivers must thus configure their devices
as wakeup capable.
This is a reworked implementation of the old wakelocks for the mmc
subsystem, originally authored by Colin Cross and San Mehat for the
Android kernel. Zoran Markovic shall also be given cred for recently
re-trying to upstream this feature.
Cc: San Mehat <san@google.com>
Cc: Colin Cross <ccross@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.
Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.
A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.
A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At several places in mmc_sdio_init_card function the cached mask in
host->ocr were being updated. To simplify code, we make use of an
local ocr parameter instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The retry and fallback mechanism when failing to switch to 1.8V
signaling voltage is handled by the SDIO card init function. Thus we
can remove the duplicated old code from the attach function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds intel_mid clovertrail SDIO and eMMC device
IDs to the sdhci-pci driver.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With lazy disable gone, no_off is not used any more in omap_hsmmc
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
clock divisor can take a max value of 1023. Update code so that card
init can be handled at f_min even at higher IP clock frequencies from
which clock to the card is derived.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With HSMMC_HAS_UPDATED_RESET reset of cmd/data (SRC/SRD) can be to
quick and can be missed resulting in wait for software timeout.
With cpu_relax timeout can be long and unpredictable. Use udelay
instead for timeout implementation.
Reported-by: Yuzheng Ma <mayuzheng@kedacom.com>
Tested-by: Yuzheng Ma <mayuzheng@kedacom.com>
Reviewed-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We want to get rid of the omap specific platform init code
callbacks as they don't play nice with device tree.
Convert the context loss check to be based on a
register state detection instead.
Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[add check for CON and HCTL in context save and restore function]
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
pbias_disable is set to protect the mmc pbias i/o cells in DT boot
by preventing voltage switch. Currently pbias_disable is enabled only
for omap3 and not for omap4 due to reg_offset difference of 0x100.
Enable pbias_disable for omap4+ too by using res->start
which does not include the reg_offset.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The i.MX6 does not support preset value feature.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The imx6q/dl supports SDR50 tunning, enable it for a better timing
on SDR50 mode.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DLL(Delay Line) is newly added to assist in sampling read data.
The DLL provides the ability to programmatically select a quantized
delay (in fractions of the clock period) regardless of on-chip variations
such as process, voltage and temperature (PVT).
This patch adds a user interface to set slave delay line via device tree.
It's usually used in high speed mode like mmc DDR mode when the signal
quality is not good caused by board design, e.g. the signal path is too
long. User can manually set delay line to find a suitable data sampling
window for card to work properly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When DDR mode is enabled, the initial pre_div should be 2.
And the pre_div value should be changed accordingly
from
...
02h) Base clock divided by 4
01h) Base clock divided by 2
00h) Base clock divided by 1
to
..
02h) Base clock divided by 8
01h) Base clock divided by 4
00h) Base clock divided by 2
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original code missed to report an error when the maximum tuning
loops exhausted or timeout, it will cause the upper layer to wrongly
think the tuning process is passed.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When reading CAP_1 register for mx6sl, ignore bit[0-15] as it stores
CAP_2 register value which is new introduced in mx6sl.
Without this fix, the max clock for mx6sl may not be correct since
it's wrongly calculated by reading CAP_1 register.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mx6sl supports standard sdhci tuning, then esdhc_executing_tuning
is only needed for mx6q/dl. We introduce is_imx6_usdhc() and
is_imx6sl_usdhc() to handle the difference.
The standard tuning is enabled by setting ESDHC_TUNE_CTRL_STD_TUNING_EN bit
in new register ESDHC_TUNE_CTRL and operates with new tuning bits
defined in SDHCI_ACMD12_ERR register.
Note: mx6sl can also work on the old manually tuning mode as mx6q/dl if
not enable standard tuning mode.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Create a struct esdhc_soc_data with moving 'flags' field from
pltfm_imx_data into it, and pass the pointer of this SoC specific data
structure through of_device_id.data directly, so that the translation
from enum imx_esdhc_type to flags can be saved.
With the change, enum imx_esdhc_type can be eliminated, since we can
implement the is_imx*_esdhc() by checking the esdhc_soc_data pointer.
The unused is_imx35_esdhc() and is_imx51_esdhc() are also removed, and the
others are kept there as we will need to use them to handle some small
register differences later, where use of new flags might be a little
overkilled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As a good practice, device driver should not modify pdev->id_entry but
keep it immutable. Let's assign of_device_id.data with imx_esdhc_type
constants directly, so that we do not have to manipulate pdev->id_entry
in .probe().
As the result, sdhci-esdhc-imx53 and sdhci-usdhc-imx6q can be removed
from platform_device_id table now, since they will only probe from
device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add flag ESDHC_FLAG_USDHC to tell that the ESDHC is actually an USDHC
block, and replace the is_imx6q_usdhc() occurrences with inline function
esdhc_is_usdhc() which checks the flag.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Just like the use of the flag ESDHC_FLAG_MULTIBLK_NO_INT, let's add
another flag ESDHC_FLAG_ENGCM07207 to enable the workaround for errata
ENGcm07207 and set the flag for i.MX25 and i.MX35 ESDHC.
While at it, let's use BIT() macro for ESDHC_FLAG_MULTIBLK_NO_INT as
well.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DMA operation in SDIO CMD53 may fail because the 4 bit SDIO mode
is not set up correctly on BF548.
Remove 2 blank lines as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implement initial SDHCI Intel Merrifield support. This patch is based
on previous one from Yunpeng Gao <yunpeng.gao@intel.com>.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the MMC bus code to use the
correct field.
Cc: Chris Ball <cjb@laptop.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Konstantin Dorfman <kdorfman@codeaurora.org>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if the mmc_gpio_request_cd fails.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spec, the pre_div for imx6q should be 1, or the biggest
clock rate we can get is a half of host clock rate. This may cause
we can not get the proper clock rate as we want. e.g. if the desired
clock is 200Mhz, however, the host clock is 200Mhz too, then it causes
the actual clock we get is 100Mhz due to pre_div is 2.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Without proper pinctrl state, the card may not be able to work
on high speed stablely. e.g. SDR104.
This patch add pinctrl state switch code according to different
uhs mode include 100mhz sate, 200mhz sate and normal state
(50Mhz and below).
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Freescale i.MX6Q/DL uSDHC clock tuning progress is a little different from
the standard tuning process defined in host controller spec v3.0.
Thus we use platform_execute_tuning instead of standard sdhci tuning.
The main difference are:
1) not only generate Buffer Read Ready interrupt when tuning is performing.
It generates all other DATA interrupts like the normal data command.
2) SDHCI_CTRL_EXEC_TUNING is not automatically cleared by HW,
instead it's controlled by SW.
3) SDHCI_CTRL_TUNED_CLK is not automatically set by HW,
it's controlled by SW.
4) the clock delay for every tuning is set by SW.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The signal voltage switch flow requires to shutdown and output
clock in a specific sequence according to standard host controller
v3.0 spec. In that timing, the card must really receive clock or not.
However, for i.MX6Q, the uSDHC will not output clock even the clock
is enabled until there is command or data in transfer on the bus,
which will then cause singal voltage switch always to fail.
For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let
controller to gate off clock automatically and set that bit
to force clock output if clock is on.
This is required by SD3.0 support.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need a lot of imx6 specific things into common esdhc_set_clock
for support SD3.0 and eMMC DDR mode which is not needed for power pc
platforms, so esdhc_set_clock seems not so common anymore.
Instead of keeping add platform specfics things into this common API,
we choose to move that code into platform driver itself to handle.
This can also exclude the dependency between imx and power pc on this
headfile and is easy for maintain in the future.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It helps for platform code to use it send tuning commands.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tuning of some platforms may not follow the standard host control
spec v3.0, e.g. Freescale uSDHC on i.MX6Q/DL.
Add a hook here to allow execute platform specific tuning instead of
standard host controller tuning.
The hook only replaces the tuning process, so it's placed after tuning
checking and before the real tuning process.
Some notes for the tuning hook:
1) it needs handle lock itself if it wants to access host controller
according platform specific implementation.
2) do not need to handle runtime pm since it executes with runtime pm
get already.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoid duplicated implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoid duplicated implementation and also fixes missing iounmap() and
release_mem_region() calls in sdhci_bcm_kona_remove(). sdhci_pltfm_init()
calls request_mem_region() and ioremap(), thus we need to call the
corresponding iounmap() and release_mem_region() calls in
sdhci_bcm_kona_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
'dw_mci_socfpga_probe' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
'dw_mci_socfpga_match' is always compiled in.
Hence of_match_ptr is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
devm_request_and_ioremap() is deprecated. Use devm_ioremap_resource()
instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In some cases, a NULL pointer dereference happens because data is NULL when
STATE_END_REQUEST case is reached in atmci_tasklet_func.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a software timeout occurs, the transfer is not stopped. In DMA case,
it causes DMA channel to be stuck because the transfer is still active
causing following transfers to be queued but not computed.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Alexander Morozov <etesial@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While speed mode is changed, CMD13 cannot be guaranteed.
According to the spec., it is not recommended to use CMD13
to check the busy completion of the timing change.
If CMD13 is used in this case, CRC error must be ignored.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In IDMAC mode EVENT_XFER_COMPLETE is set when RI/TI of last descriptor
is done. So if errors are happened in the middle of data transfers,
'dw_mci_stop_dma' during error handing can be called and eventually
prevents this flag to be set. This results in permanent wait for
EVENT_XFER_COMPLETE in 'dw_mci_tasklet_func'. Therefore, if dma
running is stopped forcibly, EVENT_XFER_COMPLETE should be set.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
First, compiling warning along with previous change is removed.
[drivers/mmc/host/dw_mmc.c:1890:7: warning: unused variable 'ctrl']
And with the recommendation in manual, IDMAC software reset is followed
by dma-reset of the CTRL register in order to terminate the transfer.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are three resets in CTRL register. FIFO reset is especially used
in several points with the same routine. It could be replaced with one
function and the others may be applied similarly if needed. So,
mci_wait_reset() is modified to allow various bit field of reset.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Main change corresponds to dw_mci_command_complete(). And EBE is
divided into read and write. Some minor changes for code readability.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In error cases, DTO interrupt may or may not be generated depending
on remained data. Stop/Abort command ensures DTO generation for that
situation. Currently if 'stop' field of data is empty, there is no
stop/abort command. So, it could hang waiting DTO. This change
reinforces these cases.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if response error is detected in case data command, data transfer
is continued. It means that data can live in FIFO. Current handling
just breaks out the request when seeing the command error. This causes
kernel panic in dw_mci_read_data_pio() [host->data = NULL]. And also,
FIFO should be guaranteed to be empty.
Unable to handle kernel NULL pointer dereference at virtual address 00000018
<...>
[<c02af814>] (dw_mci_read_data_pio+0x68/0x198) from [<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0)
[<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0) from [<c006b094>] (handle_irq_event_percpu+0x50/0x194)
[<c006b094>] (handle_irq_event_percpu+0x50/0x194) from [<c006b214>] (handle_irq_event+0x3c/0x5c)
[<c006b214>] (handle_irq_event+0x3c/0x5c) from [<c006de1c>] (handle_fasteoi_irq+0xa4/0x148)
[<c006de1c>] (handle_fasteoi_irq+0xa4/0x148) from [<c006aa88>] (generic_handle_irq+0x20/0x30)
[<c006aa88>] (generic_handle_irq+0x20/0x30) from [<c000f154>] (handle_IRQ+0x38/0x90)
[<c000f154>] (handle_IRQ+0x38/0x90) from [<c00085bc>] (gic_handle_irq+0x34/0x68)
[<c00085bc>] (gic_handle_irq+0x34/0x68) from [<c0011f40>] (__irq_svc+0x40/0x70)
Exception stack(0xef0b1c00 to 0xef0b1c48)
1c00: 000eb0cf ffffffff 00001300 c01a7738 ef295e10 0000000a c04df298 ef0b1dc0
1c20: ef295ec0 00000000 00000000 00000006 00000000 ef0b1c48 c02b1274 c01a7764
1c40: 20000113 ffffffff
[<c0011f40>] (__irq_svc+0x40/0x70) from [<c01a7764>] (__loop_delay+0x0/0xc)
Code: e1a00005 e0891006 e0662004 e12fff33 (e59a3018)
---[ end trace a7043b9ba9aed1db ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Read Threshold should be ensured that the card clock does not stop
in the middle of a block of data being transferred from the card to the
Host. Specially, clock stop is allowed in fast transfer such as HS200
or SDR104 mode. And so, it should be enabled.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This change helps to choose msize, rx_watermark and tx_watermark
depending on block size for IDMAC mode. For SDIO block size can be
variable, so if these values are set incorrectly, card clock may stop.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Both f_max and f_min will be informed for core layer to request
valid clock rate. But current setting from 'host->bus_hz' may
not represent the max/min frequency properly. Even if host can
actually support high speed than bus_hz, core layer will not
request clock rate over bus_hz. Basically, f_max/f_min can be set
with the values according to spec. And then host will make its best
effort to meet the rate.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
'supports-highspeed' is not one of the quirks but is a capability.
So, it's removed from quirks.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As host controller can support eMMC's HS200 mode at 1.8V or 1.2V,
these capability will be added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Exynos's host has divider logic before 'cclk_in' to controller core.
It means that actual clock rate of ciu clock comes from this divider
value. So, source clock should be adjusted along with 'ciu_div' which
indicates the host's divider ratio. Setting clock rate basically fits
the required speed. Specially, 'cclk_in' should have double rate of
target speed in case of DDR 8-bit mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implements variable delay tuning. In this change, exynos host can
determine the correct sampling point for the HS200 and SDR104 speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the speed modes HS200 and SDR104, tuning is needed to determine the
correct sampling point. Actual tuning procedure is provided by specific
host controller driver. This patch defines the tuning command and
tuning data. Additionally, 'struct dw_mci_slot' is moved to header
file to consider the extensive usages in driver.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Exynos5420 Mobile Storage Host controller has Security Management
Unit (SMU) for channel 0 and channel 1 (mainly for eMMC).
This time, SMU configuration is set for non-encryption mode.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current platform specific private data initialization call
dw_mci_exynos_priv_init() can be used to do platform specific
initialization of SMU and others in future. So the drv_data->init
call has moved to dw_mci_probe().
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently platform specific private data initialization is done by
dw_mci_socfpga_priv_init and dw_mci_socfpga_parse_dt. As we already have
separate platform specific device tree parser dw_mci_socfpga_parse_dt,
move the dw_mci_socfpga_priv_init code to dw_mci_socfpga_parse_dt.
We can use the dw_mci_socfpga_priv_init to do some actual platform
specific initialization.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently platform specific private data initialization is done by
dw_mci_exynos_priv_init and dw_mci_exynos_parse_dt. As we already have
separate platform specific device tree parser dw_mci_exynos_parse_dt,
move the dw_mci_exynos_priv_init code to dw_mci_exynos_parse_dt.
We can use the dw_mci_exynos_priv_init to do some actual platform
specific initialization of SMU and etc.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMOUT register is set to 0xffffffff at probe time but isn't
set after suspend/resume. Add an init of this value.
No problems were observed without this (it will also be set in
__dw_mci_start_request if there is data to send), but it makes the
register dump before and after suspend cleaner.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the dw_mmc driver would ignore any requests to disable the
card's clock. This doesn't seem like a good thing in general, but had
one extra bad side effect in the following situation:
* mmc core would set clk to 400kHz at boot time while scanning
* mmc core would set clk to 0 since no card, but it would be ignored.
* suspend to ram and resume; clocks in the dw_mmc IP block are now 0
but dw_mmc thinks that they're 400kHz (it ignored the set to 0).
* insert card
* mmc core would set clk to 400kHz which would be considered a no-op.
Note that if there is no card in the slot and we do a suspend/resume
cycle, we _do_ still end up with differences in a dw_mmc register
dump, but the differences are clock related and we've got the clock
disabled both before and after, so this should be OK.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up
looping around forever. This has been seen to happen on exynos5420
silicon despite the fact that we haven't enabled any wakeup events due
to a silicon errata. It is safe to do on all exynos variants.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC subsystem handles looking for a card at probe time. Queuing up our
own can race with the rest of the MMC subsystem and cause problems if we
get unlucky with timing. Just remove driver own detection triggering. While
progressing the request from 'mmc_rescan', if 'dw_mci_work_routine_card'
routine is activated, it will cancel the current request. The problem case
is that 'mmc_rescan' is prior to 'dw_mci_work_routine_card' from host own.
Specifically, the following message shows the detection problem in driver's
probing. It would get an err -123 (-ENOMEDIUM) during probe.
[ 4.216595] dwmmc_exynos 12210000.dwmmc1: Using internal DMA controller.
[ 4.395935] dwmmc_exynos 12210000.dwmmc1: Version ID is 250a
[ 4.401948] dwmmc_exynos 12210000.dwmmc1: DW MMC controller at irq 108, 64 bit host data width, 64 deep fifo
[ 4.424430] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.453975] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.459592] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 4.484258] dwmmc_exynos 12210000.dwmmc1: 1 slots initialized
[ 4.485406] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.487606] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.489794] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.509757] mmc1: error -123 whilst initialising SDIO card
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
cscope says there are no callers for mmc_try_claim_host in the kernel.
No reason to keep it.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If a corresponding power domain exists for the device and it manages
to cut the domain regulator while the device is runtime suspended,
the IP loses it's registers context. We restore the context in the
.runtime_resume callback from the existing register caches to adapt
to this situation.
We also want to make sure the registers are in a known state while
restoring context in the case when the power domain did not drop the
power, since there are restrictions for the order of writing to these
registers. To handle this, we clear the registers in the
.runtime_suspend callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After a write to the MMCICLOCK register data cannot be written to this
register for three feedback clock cycles. Writes to the MMCIPOWER
register must be separated by three MCLK cycles. Previously no issues
has been observered, but using higher ARM clock frequencies on STE-
platforms has triggered this problem.
The MMCICLOCK register is written to in .set_ios and for some data
transmissions for SDIO. We do not need a delay at the data transmission
path, because sending and receiving data will require more than three
clock cycles. Then we use a simple logic to only delay in .set_ios and
thus we don't affect throughput performance.
Signed-off-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By optionally putting the pins into sleep state in the .runtime_suspend
callback we can accomplish two things. One is to minimize current leakage
from pins and thus save power, second we can prevent the IP from driving
pins output in an uncontrolled manner, which may happen if the power domain
drops the domain regulator.
When returning from idle, entering .runtime_resume callback, the pins
are restored to default state.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no need for every driver to fetch a pinctrl handle and to
select the default state. Instead this is handled by the device driver
core, thus we can remove this piece of code from mmci.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving support,
better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=a7dU
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
Update copyright date, and remove author address.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If switching voltage fails, SD_CLK toggle enable bit should been cleared
so that SD host can control SD clock automatically.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adapt Kconfig to include ARC in supported architectures
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In order to use the quirks2, initialized the host->quirks2.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <Kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When use the QUIRK_NONSTANDARD_CLOCK, then never set to 0 at clock control
register. This patch fixes this problem.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=mpcX
-----END PGP SIGNATURE-----
Merge tag 'bcm-for-3.12-late-soc' of git://github.com/broadcom/bcm11351 into next/boards
From Christian Daudt, late changes for 3.12 broadcom mmc driver. Small
trivial changes so I'll take them through arm-soc.
* tag 'bcm-for-3.12-late-soc' of git://github.com/broadcom/bcm11351:
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
sdhci_bcm_kona_card_event is referenced only in this file.
Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
version.h header inclusion is not necessary as detected by
versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
Add suppport to get voltage from device-tree node for esdhc host,
if voltage-ranges was specified in device-tree node we can get
ocr_mask instead of read from host capacity register. If not voltages
still can be get from host capacity register.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We use host->ocr_mask to hold the voltage get from device-tree
node, In case host->ocr_mask was available, we use host->ocr_mask
as the final available voltage can be used by MMC/SD/SDIO card.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
OMAP's hs_mmc driver is used for MMC controller operation on many
omap2plus SoCs (OMAP2430, OMAP3, 4, 5 and AM335x).
Considering that the device tree entries are already present for these,
allow the driver to be built using the config ARCH_OMAP2PLUS rather
than individually adding a config for each SoC to enable the
support.
Use COMPILE_TEST to enable the build for other platforms.
Signed-off-by: Amarinder Bindra <a-bindra@ti.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 1f6b9fa40e consolidated writes to
the STAT register in one location, moving them from omap_hsmmc_do_irq()
to omap_hsmmc_irq(). This move has the unwanted side effect that the
controller status flags are potentially cleared after a new command has
been started as a consequence of reading the previous status flags.
This means that if the new command changes the status flags before the
IRQ routine returns, those flags may be cleared without handling the
event which asserted them, and thus missing the event.
Move the writing of the STAT register back in omap_hsmmc_do_irq(),
before handling the status flags which generated the interrupt.
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Reviewed-and-Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Exynos5420 has a DWMMC controller which is different from prior
versions.This patch adds a new compatible string for Exynos5420.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some newer MMCIF IP revisions contain a CE_CLK_CTRL2 register, that has to
be set for proper operation. Support for this feature is added in a way to
preserve the current behaviour by default, i.e. when it is not enabled
in platform data. Patch is based on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some earlier MMCIF IP revisions contained Command Completion Signal
support, which has been dropped again in modern versions. Sopport for
this feature is added in a way to preserve the current behaviour by
default, i.e. when it is not enabled in platform data. Patch is based
on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To use DMA in the Device Tree case the driver has to be modified
to use suitable API to obtain DMA channels.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sh_dma.h isn't needed in sh_mmcif.h, move it into sh_mmcif.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add further OF compatibility strings to the SDHI driver to be able to
precisely control driver's behaviour on each of them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch enables bus-mastering mode for MMC controller to allow IDMAC
transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Prabu Thangamuthu <Prabu.T@synopsys.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is a typo when the mapped space is from BAR 2, but BAR 0 is
used instead. This patch fixes the typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Prabu Thangamuthu <Prabu.T@synopsys.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All platforms now pass the CD and RO GPIOs to the MMC SPI driver, those
callbacks are not used anymore. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for passing CD/RO GPIO numbers directly to the mmc_spi
driver instead of relying solely on board code callbacks to retrieve the
CD/RO signals values. The driver will enable debouncing on the card
detect GPIO if the cd_debounce field is set to a non-zero value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Include 'dw_mmc-pltfm.h' header file in order to fix the following
sparse warnings:
drivers/mmc/host/dw_mmc-pltfm.c:36:5: warning: symbol 'dw_mci_pltfm_register' was not declared. Should it be static?
drivers/mmc/host/dw_mmc-pltfm.c:94:1: warning: symbol 'dw_mci_pltfm_pmops' was not declared. Should it be static?
drivers/mmc/host/dw_mmc-pltfm.c:118:5: warning: symbol 'dw_mci_pltfm_remove' was not declared. Should it be static?
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
I'm testing SH-Mobile SDHI driver in DMA mode with a new DMA controller using
'bonnie++' and getting DMA error after which the tmio_mmc_dma.c code falls back
to PIO but all commands time out after that. It turned out that the fallback
code calls tmio_mmc_enable_dma() with RX/TX channels already freed and pointers
to them cleared, so that the function bails out early instead of clearing the
DMA bit in the CTL_DMA_ENABLE register. The regression was introduced by commit
162f43e31c (mmc: tmio: fix a deadlock).
Moving tmio_mmc_enable_dma() calls to the top of the PIO fallback code in
tmio_mmc_start_dma_{rx|tx}() helps.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Chris Ball <cjb@laptop.org>
Added missing MFD_SYSCON dependency for SOCFPGA in order to fix
the following link error.
drivers/mmc/host/dw_mmc-socfpga.c:49: undefined reference to `syscon_regmap_lookup_by_compatible'
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A previous commit (fdfa20c163) reordered the shutdown sequence
in mmc_blk_remove_req. However, mmc_cleanup_queue is now called before
we get the card pointer, and mmc_cleanup_queue sets mq->card to NULL.
This patch moves the card pointer assignment before mmc_cleanup_queue.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be used.
Also, both kstrtol() and copy_from_user() can be replaced
with kstrtol_from_user() to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since SD Physical Layer specification V3.0, AU_SIZE is supported up
to 0xf. So If SD-card is supported v3.0, then max_au should be 0xf.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In function mmc_sd_init_card, if command 3/9/7 got failed, mmc_card
allocated just before won't be freed. This would cause memory leak.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
omap_hsmmc.c depends on <linux/sizes.h> being included indirectly by
another header. Once we enable COMPILE_TEST for this driver, we might
compile under architectures which won't include <linux/sizes.h> for us.
In fact, one such case is x86.
In order to prevent compile breakages, let's explicitly include
<linux/sizes.h>.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In (1fb5f68 mmc: dw_mmc: Don't loop when handling an interrupt), the
code for handling DW_MCI_QUIRK_IDMAC_DTO became dead code. Move it to
where it ought to live.
Found by code inspection and compile-tested only--I don't know of any
boards that need DW_MCI_QUIRK_IDMAC_DTO.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current MMC driver doesn't handle generic error (bit19 of device
status) in write sequence. As a result, write data gets lost when
generic error occurs. For example, a generic error when updating a
filesystem management information causes a loss of write data and
corrupts the filesystem. In the worst case, the system will never
boot.
This patch includes the following functionality:
1. To enable error checking for the response of CMD12 and CMD13
in write command sequence
2. To retry write sequence when a generic error occurs
Messages are added for v2 to show what occurs.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Chris Ball <cjb@laptop.org>
stmp_reset_block() may fail, so let's check its return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Using devm_clk_get() allows us to remove the clk_put() calls, so
let's use it to simplify the code.
Rename the 'out_clk_put' label to 'out_clk_disable' now that clk_put
is removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also there is already a error message within
devm_ioremap_resource(), so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
'vub300_init_card' is used only in this file. Make it
static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
'bcm2835_sdhci_get_min_clock' is used only in this file.
Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
sdhci-bcm-kona driver is incorrectly doing "|" to bit-test
NONREMOVABLE. Switch to "&"
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
This change makes the following build warning go away:
[...]
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
WARNING: modpost: Found 2 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
