The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.
Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.
The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):
$ tc qdisc change taprio dev IFACE parent root \
base-time X \
sched-entry <CMD> <GATES> <INTERVAL> \
...
Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.
Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.
So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.
For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.
Example:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time $BASE_TIME \
sched-entry S 00 500000 \
sched-entry S 0f 500000 \
clockid CLOCK_TAI
The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, this isn't a problem, but the next commit allows schedules
to be added during runtime. When a new schedule transitions from the
inactive to the active state ("admin" -> "oper") the previous one can
be freed, if it's freed just after the RCU read lock is released, we
may access an invalid entry.
So, we should take care to protect the dequeue() flow, so all the
places that access the entries are protected by the RCU read lock.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng says:
====================
undo congestion window on spurious SYN or SYNACK timeout
Linux TCP currently uses the initial congestion window of 1 packet
if multiple SYN or SYNACK timeouts per RFC6298. However such
timeouts are often spurious on wireless or cellular networks that
experience high delay variances (e.g. ramping up dormant radios or
local link retransmission). Another case is when the underlying
path is longer than the default SYN timeout (e.g. 1 second). In
these cases starting the transfer with a minimal congestion window
is detrimental to the performance for short flows.
One naive approach is to simply ignore SYN or SYNACK timeouts and
always use a larger or default initial window. This approach however
risks pouring gas to the fire when the network is already highly
congested. This is particularly true in data center where application
could start thousands to millions of connections over a single or
multiple hosts resulting in high SYN drops (e.g. incast).
This patch-set detects spurious SYN and SYNACK timeouts upon
completing the handshake via the widely-supported TCP timestamp
options. Upon such events the sender reverts to the default
initial window to start the data transfer so it gets best of both
worlds. This patch-set supports this feature for both active and
passive as well as Fast Open or regular connections.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate the congestion window initialization from tcp_init_metrics()
to tcp_init_transfer() to improve code readability.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a helper to consolidate two identical code block for passive TFO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes passive Fast Open reverts the cwnd to default
initial cwnd (10 packets) if the SYNACK timeout is spurious.
Passive Fast Open uses a full socket during handshake so it can
use the existing undo logic to detect spurious retransmission
by recording the first SYNACK timeout in key state variable
retrans_stamp. Upon receiving the ACK of the SYNACK, if the socket
has sent some data before the timeout, the spurious timeout
is detected by tcp_try_undo_recovery() in tcp_process_loss()
in tcp_ack().
But if the socket has not send any data yet, tcp_ack() does not
execute the undo code since no data is acknowledged. The fix is to
check such case explicitly after tcp_ack() during the ACK processing
in SYN_RECV state. In addition this is checked in FIN_WAIT_1 state
in case the server closes the socket before handshake completes.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP sender would use congestion window of 1 packet on the second SYN
and SYNACK timeout except passive TCP Fast Open. This makes passive
TFO too aggressive and unfair during congestion at handshake. This
patch fixes this issue so TCP (fast open or not, passive or active)
always conforms to the RFC6298.
Note that tcp_enter_loss() is called only once during recurring
timeouts. This is because during handshake, high_seq and snd_una
are the same so tcp_enter_loss() would incorrect set the undo state
variables multiple times.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux implements RFC6298 and use an initial congestion window
of 1 upon establishing the connection if the SYNACK packet is
retransmitted 2 or more times. In cellular networks SYNACK timeouts
are often spurious if the wireless radio was dormant or idle. Also
some network path is longer than the default SYNACK timeout. In
both cases falsely starting with a minimal cwnd are detrimental
to performance.
This patch avoids doing so when the final ACK's TCP timestamp
indicates the original SYNACK was delivered. It remembers the
original SYNACK timestamp when SYNACK timeout has occurred and
re-uses the function to detect spurious SYN timeout conveniently.
Note that a server may receives multiple SYNs from and immediately
retransmits SYNACKs without any SYNACK timeout. This often happens
on when the client SYNs have timed out due to wireless delay
above. In this case since the server will still use the default
initial congestion (e.g. 10) because tp->undo_marker is reset in
tcp_init_metrics(). This is an intentional design because packets
are not lost but delayed.
This patch only covers regular TCP passive open. Fast Open is
supported in the next patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detecting spurious SYNACK timeout using timestamp option requires
recording the exact SYNACK skb timestamp. Previously the SYNACK
sent timestamp was stamped slightly earlier before the skb
was transmitted. This patch uses the SYNACK skb transmission
timestamp directly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux implements RFC6298 and use an initial congestion window of 1
upon establishing the connection if the SYN packet is retransmitted 2
or more times. In cellular networks SYN timeouts are often spurious
if the wireless radio was dormant or idle. Also some network path
is longer than the default SYN timeout. Having a minimal cwnd on
both cases are detrimental to TCP startup performance.
This patch extends TCP undo feature (RFC3522 aka TCP Eifel) to detect
spurious SYN timeout via TCP timestamps. Since tp->retrans_stamp
records the initial SYN timestamp instead of first retransmission, we
have to implement a different undo code additionally. The detection
also must happen before tcp_ack() as retrans_stamp is reset when
SYN is acknowledged.
Note this patch covers both active regular and fast open.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously if an active TCP open has SYN timeout, it always undo the
cwnd upon receiving the SYNACK. This is because tcp_clean_rtx_queue
would reset tp->retrans_stamp when SYN is acked, which fools then
tcp_try_undo_loss and tcp_packet_delayed. Addressing this issue is
required to properly support undo for spurious SYN timeout.
Fixing this is tricky -- for active TCP open tp->retrans_stamp
records the time when the handshake starts, not the first
retransmission time as the name may suggest. The simplest fix is
for tcp_packet_delayed to ensure it is valid before comparing with
other timestamp.
One side effect of this change is active TCP Fast Open that incurred
SYN timeout. Upon receiving a SYN-ACK that only acknowledged
the SYN, it would immediately retransmit unacknowledged data in
tcp_ack() because the data is marked lost after SYN timeout. But
the retransmission would have an incorrect ack sequence number since
rcv_nxt has not been updated yet tcp_rcv_synsent_state_process(), the
retransmission needs to properly handed by tcp_rcv_fastopen_synack()
like before.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "pass through" with a proper "fall through" annotation
in order to fix the following warning:
drivers/net/netdevsim/bus.c: In function ‘new_device_store’:
drivers/net/netdevsim/bus.c:170:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_count = 1;
~~~~~~~~~~~^~~
drivers/net/netdevsim/bus.c:172:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This fix is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
case MC_CMD_FCNTL_OFF:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.
With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: atlantic: Aquantia driver updates 2019-04
This patchset contains various improvements:
- Work targeting link up speedups: link interrupt introduced, some other
logic changes to imrove this.
- FW operations securing with mutex
- Counters and statistics logic improved by Dmitry
- read out of chip temperature via hwmon interface implemented by
Yana and Nikita.
v4 changes:
- remove drvinfo_exit noop
- 64bit stats should be readed out sequentially (lsw, then msw)
declare 64bit read ops for that
v3 changes:
- temp ops renamed to phy_temp ops
- mutex commits squashed for better structure
v2 changes:
- use threaded irq for link state handling
- rework hwmon via devm_hwmon_device_register_with_info
Extra comments on review from Andrew:
- direct device name pointer is used in hwmon registration.
This causes hwmon device to derive possible interface name changes
- Will consider sanity checks for firmware mutex lock separately.
Right now there is no single point exsists where such check could
be easily added.
- There is no way now to fetch and configure min/max/crit temperatures
via FW. Will investigate this separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).
Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo in msi code. No much impact though.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve for better readability
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we define and request an extra interrupt line,
assign it on link isr handler and restructure abit aq_pci code
to better support that.
We also remove logic for using different timer intervals
depending on link state, since thats now useless.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need this to schedule link interrupt handling and
various service tasks.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define link interrupt handler
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for hwmon api to fetch out chip temperature
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Neil who reported the issue leading to this
workaround, the workaround is no longer needed since
version 5.0. So let's remove it.
This was the bug report leading to the workaround:
https://bugzilla.kernel.org/show_bug.cgi?id=201081
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: improve eri function handling
This series aims at improving and simplifying the eri functions.
No functional change intended.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fortunately in one place there's a comment explaining what toggling
this bit does. So let's create a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers rtl_eri_set_bits and rtl_eri_clear_bits to improve
readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In basically all eri function calls the type argument is ERIAR_EXGMAC.
Therefore make it the default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Convert mv88e6060 to mdio device
This patchset builds upon the previous patches to mv88e6060. It adds
support for probing the switch as an MDIO device and then removes the
legacy probe method. Since this is the last device supporting legacy
probe, this allows legacy probe to be removed, originally planned to
be removed in 4.17, but took a bit longer.
This change to the mv88e6060 is more risky than the previous
patchset. Some attempts to test it have been made, by hacking the
driver to match on an mv88e6352 so that it probes. These changes are
all about probe, so it is a reasonable test. But testing on a real
mv88e6060 would be great.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code to support the legacy binding has been removed,
remove the documentation for it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver can be probed as an mdio device, remove the legacy
DSA platform device probing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probing DSA devices as platform devices has been superseded by using
normal bus drivers. Add support for probing the mv88e6060 device as an
mdio device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Improvements to DSA core VLAN manipulation
In preparation of submitting the NXP SJA1105 driver, the Broadcom b53
and Mediatek mt7530 drivers have been found to apply some VLAN
workarounds that are needed in the new driver as well.
Therefore this patchset is mostly simply promoting the DSA driver
workarounds for VLAN to the generic code.
The b53 driver was applying a few workarounds in order to convince DSA
that its vlan_filtering setting is not really per-port. This is now
simply set by the driver via a DSA variable at probe time. The sja1105
driver will be a second user of this.
The mt7530 was also keeping track of when the .port_vlan_filtering
callback was being called. Remove the kept state from this driver
and simplify dealing with vlan_filtering in the generic case.
TODO:
Find the best way to deal generically with the situation described below
(discussion at https://lkml.org/lkml/2019/4/16/1355):
> > +Segregating the switch ports in multiple bridges is supported (e.g. 2 + 2), but
> > +all bridges should have the same level of VLAN awareness (either both have
> > +``vlan_filtering`` 0, or both 1). Also an inevitable limitation of the fact
> > +that VLAN awareness is global at the switch level is that once a bridge with
> > +``vlan_filtering`` enslaves at least one switch port, the other un-bridged
> > +ports are no longer available for standalone traffic termination.
>
> That is quite a limitation that I don't think I had fully grasped until
> reading your different patches. Since enslaving ports into a bridge
> comes after the network device was already made available for use, maybe
> you should force the carrier down or something along those lines as soon
> as a port is enslaved into a bridge with vlan_filtering=1 to make this
> more predictable for the user?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was recently introduced, so keeping state inside the driver is no
longer necessary.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since different types of hardware may or may not support this setting
per-port, DSA keeps it either in dsa_switch or in dsa_port.
While drivers may know the characteristics of their hardware and
retrieve it from the correct place without the need of helpers, it is
cumbersone to find out an unambigous answer from generic DSA code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver, recognizing that the .port_vlan_filtering callback was never
coming after the port left its parent bridge, decided to take that duty
in its own hands. DSA now takes care of this condition, so fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are standalone (after they left the bridge), they should have
no VLAN filtering semantics (they should pass all traffic to the CPU).
Currently this is not true for switchdev drivers, because the bridge
"forgets" to unset that.
Normally one would think that doing this at the bridge layer would be a
better idea, i.e. call br_vlan_filter_toggle() from br_del_if(), similar
to how nbp_vlan_init() is called from br_add_if().
However what complicates that approach, and makes this one preferable,
is the fact that for the bridge core, vlan_filtering is a per-bridge
setting, whereas for switchdev/DSA it is per-port. Also there are
switches where the setting is per the entire device, and unsetting
vlan_filtering one by one, for each leaving port, would not be possible
from the bridge core without a certain level of awareness. So do this in
DSA and let drivers be unaware of it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
