If an edge interrupt triggers while entering idle just before we save
GPIO datain register to saved_datain, the triggered GPIO will not be
noticed on wake-up. This is because the saved_datain and GPIO datain
are the same on wake-up in omap_gpio_unidle(). Let's fix this by
ignoring any pending edge interrupts for saved_datain.
This issue affects only idle states where the GPIO module internal
wake-up path is operational. For deeper idle states where the GPIO
module gets powered off, Linux generic wakeirqs must be used for
the padconf wake-up events with pinctrl-single driver. For examples,
please see "interrupts-extended" dts usage in many drivers.
This issue can be somewhat easily reproduced by pinging an idle system
with smsc911x Ethernet interface configured IRQ_TYPE_EDGE_FALLING. At
some point the smsc911x interrupts will just stop triggering. Also if
WLCORE WLAN is used with EDGE interrupt like it's documentation specifies,
we can see lost interrupts without this patch.
Note that in the long run we may be able to cancel entering idle by
returning an error in gpio_omap_cpu_notifier() on pending interrupts.
But let's fix the bug first.
Also note that because of the recent clean-up efforts this patch does
not apply directly to older kernels. This does fix a long term issue
though, and can be backported as needed.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The FMC subsystem was created in 2012 with the ambition to
drive development of drivers for this hardware upstream.
The current implementation has architectural flaws and would
need to be revamped using real hardware to something that can
reuse existing kernel abstractions in the subsystems for e.g.
I2C, FPGA and GPIO.
We have concluded that for the mainline kernel it will be
better to delete the subsystem and start over with a clean
slate when/if an active maintainer steps up.
For details see:
https://lkml.org/lkml/2018/10/29/534
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_startup() method returns an unsigned int, but in __irq_startup()
it is assigned to an int. However, nothing checks for errors, so any
error that is returned is ignored.
Remove the check for GPIO-input mode and the error return.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must never alter the register tables; these are read-only as far
as the driver is concerned. Constify these tables.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use local variables to store the base iomem address and regs table
pointer like omap_gpio_init_context() does. Not only does this make
the function neater, it also avoids unnecessary reloads of the same
data multiple times.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO block has the set/clear dataout registers implemented, it
also has the normal dataout register implemented. Reading this register
reads the current GPIO output state, and writing it sets the GPIOs to
the explicit state. This is the behaviour that we want when saving and
restoring the context, so use the dataout register exclusively.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
omap_set_gpio_irqenable() calls two helpers that are almost the same
apart from whether they set or clear bits. We can consolidate these:
- in the set/clear bit register case, we can perform the operation on
our saved context copy and write the appropriate set/clear register.
- otherwise, we can use our read-modify-write helper and invert enable
if irqenable_inv is set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function open-codes an exclusive-or bitwise operation using an
if() statement and explicitly setting or clearing the bit. Instead,
use an exclusive-or operation instead, and simplify the function.
We can combine the preprocessor conditional using IS_ENABLED() and
gain some additional compilation coverage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We already have a read-modify-write helper, but there's more that can
be done with a read-modify-write helper if it returned the new value.
Modify the existing helper to return the new value, and arrange for
it to take one less argument by having the caller compute the register
address.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
bank->level_mask is merely the bitwise or of the level detection
context which we have already read in this function. Rather than
repeating additional reads, compute it from the values already
read.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the reasons for set_multiple() to exist is to allow multiple
GPIOs on the same chip to be changed simultaneously - see commit
5f42424354 ("gpiolib: allow simultaneous setting of multiple GPIO
outputs"):
- Simultaneous glitch-free setting of multiple pins on any kind of
parallel bus attached to GPIOs provided they all reside on the
same chip and bank.
In order for this to work, we should not use the atomic set/clear
registers, but instead read-modify-write the dataout register. We
already take the spinlock to ensure that happens atomically, so
move the code into the set_multiple() function and kill the two
helper functions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no reason to have helper functions to read the datain and
dataout registers when they are only used in one location. Simplify
this code to make it more readable.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
omap_gpio_get() calls omap_get_gpio_datain() or omap_get_gpio_dataout()
to read the GPIO state. These two functions are only called from this
method, so they don't add much value. Move their contents into
omap_gpio_get() method and simplify.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Architectures are single-copy atomic, which means that simply reading
a register is an inherently atomic operation. There is no need to
take a spinlock here.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move these two functions to live beside the rest of the gpio chip
implementation, rather than in the middle of the irq chip
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_ack method does not fit our hardware requirements. Edge
interrupts must be cleared before we handle them, and level interrupts
must be cleared after handling them.
We handle the interrupt clearance in our interrupt handler for edge IRQs
and in the unmask method for level IRQs.
Replace the irq_ack method with the no-op method from the dummy irq
chip.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The edge interrupt handling was effectively:
isr = ISR_reg & enabled;
if (bank->level_mask)
level_mask = bank->level_mask & enabled;
else
level_mask = 0;
edge = isr & ~level_mask;
When bank->level_mask is zero, level_mask will be computed as zero
anyway, so the if() statement is redundant. We are then left with:
isr = ISR_reg & enabled;
level_mask = bank->level_mask & enabled;
edge = isr & ~level_mask;
This can be simplified further to:
isr = ISR_reg & enabled;
edge = isr & ~bank->level_mask;
since the second mask with 'enabled' is redundant.
Improve the associated comment as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit c4791bc6e3 ("gpio: omap: drop omap_gpio_list") removed the
list head and addition to the list head of each gpio bank, but failed
to remove the list_del() call and the node inside struct gpio_bank.
Remove these too.
Fixes: c4791bc6e3 ("gpio: omap: drop omap_gpio_list")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 384ebe1c28 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998 ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.
This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.
Fixes: 4e962e8998 ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Documentation states:
NOTE: There must be a correlation between the wake-up enable and
interrupt-enable registers. If a GPIO pin has a wake-up configured
on it, it must also have the corresponding interrupt enabled (on
one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt. This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and
trigger setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The stmmac driver currently ignores the GPIO flags which are passed via
devicetree because it operates with legacy GPIO numbers instead of GPIO
descriptors. stmmac assumes that the GPIO is "active HIGH" by default.
This can be overwritten by setting "snps,reset-active-low" to make the
reset line "active LOW".
Recent Amlogic SoCs (G12A which includes S905X2 and S905D2 as well as
G12B which includes S922X) use GPIOZ_14 or GPIOZ_15 for the PHY reset
line. These GPIOs are special because they are marked as "3.3V input
tolerant open drain" pins which means they can only drive the pin output
LOW (to reset the PHY) or to switch to input mode (to take the PHY out
of reset).
The GPIO subsystem already supports this with the GPIO_OPEN_DRAIN and
GPIO_OPEN_SOURCE flags in the devicetree bindings.
Add the stmmac PHY reset line specific active low parsing to gpiolib-of
so stmmac can be ported to GPIO descriptors while being backwards
compatible with device trees which use the "old" way of specifying the
polarity.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keeping the irq_chip definition static shares it with multiple instances
of the altera gpiochip in the system. This is bad and now we get this
warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from being driver static into the
struct altera_gpio_chips. So a unique irq_chip is used for each gpiochip
instance.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver was using the OF GPIO helper API, but barely used any of its
features and it cost more code than it saved. Also, the OF GPIO code is
now deprecated. Convert it to use a more standard setup and use devm
APIs for initialization to avoid the need for a remove function.
Our rationale for this change is that we are using the Xilinx GPIO with
resources injected using the MFD core rather than on the device tree
itself. Using platform rather than OF-specific resources allows this to
work for free.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
FMC has its own GPIO handling, the inclusion of <linux/gpio.h>
is only to reuse some flags that we can just as well provide
using local defines.
Cc: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch adds k3 am654 compatible, specific properties and
an example.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the compiler warning with ARM64 config enabled
as the current mask assumes 32 bit by default.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a gpio_chip wants to request a descriptor from itself
using gpiochip_request_own_desc() it needs to be able to specify
fully how to use the descriptor, notably line inversion
semantics. The workaround in the gpiolib.c can be removed
and cases (such as SPI CS) where we need at times to request
a GPIO with line inversion semantics directly on a chip for
workarounds, can be fully supported with this call.
Fix up some users of the API that weren't really using the
last flag to set up the line as input or output properly
but instead just calling direction setting explicitly
after requesting the line.
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With ReST, [foo]_ means a reference to foo, causing this warning:
Documentation/driver-api/gpio/driver.rst:419: WARNING: Unknown target name: "devm".
Fix it by using a literal for the name.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TI TCA9539 is a variant of the PCA953x GPIO expander,
with 16 GPIOs and interrupt functionality.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Freescale SPI chipselects are special: while everyone else
is using "cs-gpios" the Freescale platforms just use "gpios".
Fix this by responding with "gpios" when asking for "cs-gpios"
in a freescale device node, so we hide this pecularity from
the SPI core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the Arm PL061 GPIO controller binding to json-schema format.
As I'm the author for all but the gpio-ranges line, make the schema dual
GPL/BSD license.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'default (active high)' lines are repeated twice. Avoid people stare at
their screens looking for differences.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use standard functions. Eventually we will be able to drop all
checks and just assign irq_domain_translate_twocell() to this
callback.
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This feature is deprecated, it is helpful to inform users about
this. I'm resisting the temptation to add "depends on BROKEN"
to this, but saving that for later.
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GCC 9 now warns about calling memset() on partial structures when it
goes across multiple fields. This adds a helper for the place in
tracing that does this type of clearing of a structure.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXOrlfhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qoDhAP4mogBm0JjJ1LWr8RX2/X7qFm0x1zLz
5Mk0QKfeRP3MYgEAl2mV/HeFp7aMxEY2CKy0LslmaXPhamPx1r0LlfMgIws=
=drP3
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing warning fix from Steven Rostedt:
"Make the GCC 9 warning for sub struct memset go away.
GCC 9 now warns about calling memset() on partial structures when it
goes across multiple fields. This adds a helper for the place in
tracing that does this type of clearing of a structure"
* tag 'trace-v5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Silence GCC 9 array bounds warning
merge window, but should not wait four months before they appear in
a release. I also travelled a bit more than usual in the first part
of May, which didn't help with picking up patches and reports promptly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc6RkmAAoJEL/70l94x66DhEAH/ijCkibV9vOUu8n/lSxMjAzi
I/Y1VEaVRFuQ6u0QSjWBBg22tVsWuWiVbonJ63w3JMRwi5Q5zW9REE7EaKRAa/eC
FiFE7vTesYh6sGVwdMCwoinjMDyCp7hybvtBc608+MWhVmrdzTYtPm5N85wxIDtW
xH5Kr2mVeLC43X3vfegolmXZ1obAbZEToJvOgJrYFhnzsmVYYl182kfGtrppBoO0
XXDPuDRGpTrm6A2oADMdOv+mT9p51pHsedmHQaDGXwAGEC/BkOGKdIdBfwppEwy7
QP2NGqwkHIyghV1aCPacT6O6G6xL0i2rfvlJ7+e6o7deU4uMXAqIdQ2DbIcHy3g=
=5IW2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"The usual smattering of fixes and tunings that came in too late for
the merge window, but should not wait four months before they appear
in a release.
I also travelled a bit more than usual in the first part of May, which
didn't help with picking up patches and reports promptly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (33 commits)
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
KVM: LAPIC: Expose per-vCPU timer_advance_ns to userspace
KVM: LAPIC: Fix lapic_timer_advance_ns parameter overflow
kvm: vmx: Fix -Wmissing-prototypes warnings
KVM: nVMX: Fix using __this_cpu_read() in preemptible context
kvm: fix compilation on s390
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzqGSoACgkQ8vlZVpUN
gaNhqQgAiUHwKalYrZ82NwBQGnHcKcWv3JEE9vt8Bsu4fPUzirrEqYiSudvj6nHv
8uYFKHmGx7+GEWxLfwlVZzRjLlgZqa0kpyfNFEL01KFdbFsKQN4gTYvvky+OVftr
nRZ7tp66Y5hErwn/Y0wWn9WHFOykhxGi+kv5m5CFZ7MNec/b+1H2U1hXkhSt6oug
IO2wLZYLFSPXlrqfJLV7HYJ/OX1mO7g1viCNGvpRmrvLmjmO09q0/6DF3QNAvGmj
sXXu0eV+N/Ir0so0RbeN60ZeDXaoyeOZbXFlH9zfJEgkoFv+adZjT65bQEvSUWQ2
J/v4rLXd8gmCiVwOuEbCoLKebT/nbg==
=Wf1M
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"Fix a soft lockup regression when reading from /dev/random in early
boot"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix soft lockup when trying to read from an uninitialized blocking pool
Fixes: eb9d1bf079: "random: only read from /dev/random after its pool has received 128 bits"
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Starting with GCC 9, -Warray-bounds detects cases when memset is called
starting on a member of a struct but the size to be cleared ends up
writing over further members.
Such a call happens in the trace code to clear, at once, all members
after and including `seq` on struct trace_iterator:
In function 'memset',
inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3:
./include/linux/string.h:344:9: warning: '__builtin_memset' offset
[8505, 8560] from the object at 'iter' is out of the bounds of
referenced subobject 'seq' with type 'struct trace_seq' at offset
4368 [-Warray-bounds]
344 | return __builtin_memset(p, c, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In order to avoid GCC complaining about it, we compute the address
ourselves by adding the offsetof distance instead of referring
directly to the member.
Since there are two places doing this clear (trace.c and trace_kdb.c),
take the chance to move the workaround into a single place in
the internal header.
Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.com
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
[ Removed unnecessary parenthesis around "iter" ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzppnIACgkQ8vlZVpUN
gaOWcwf/YmIeCi7HHuOJG5STYhMZjbAoK7eCNSjmP0HBIpyZSBaSZg1/ZEmtTVA6
SyGWxYD2xymphkEcRQ20pF8h2CYurHsjYl9RH+Im2iaCzdeFKvgfYxSSsqsaZixM
ejQK22W6mVULd1RqFGNPeo+5v7Fxn6fK0zw2k5JrLjFnIRq/XIA7qMdjblPOcfi+
QT/K9a2DZ5vHBGDKjEiVA+a0HX6bxdGTiiT4LW+uiHUJUESBWNQJqOHJqno9VdFh
J97/3XJHMGPAbjD4AiINAL0x8IZ2FXx1H+QgVDnrxy8lVrYaMVvWMEokMQ7HvkFr
SmYddgBPUHO+kk4u34nznZNuesvOqQ==
=dFk1
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes (including a regression fix) for ext4"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix dcache lookup of !casefolded directories
ext4: do not delete unlinked inode from orphan list on failed truncate
ext4: wait for outstanding dio during truncate in nojournal mode
ext4: don't perform block validity checks on the journal inode
code and I forgot to incorporate them.
I also added a small clean up patch that was sent to me a while ago
and I just noticed it.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXOixqRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlPsAQCmNzno+SJMXLLIojZ80pqs9PqLqIrW
iBopFNihRBAkxgEAle8Pvr53S4R/Hjn6j++kxBm/uWaEfICOzyqcSyqxlQA=
=Sin+
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Tom Zanussi sent me some small fixes and cleanups to the histogram
code and I forgot to incorporate them.
I also added a small clean up patch that was sent to me a while ago
and I just noticed it"
* tag 'trace-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
kernel/trace/trace.h: Remove duplicate header of trace_seq.h
tracing: Add a check_val() check before updating cond_snapshot() track_val
tracing: Check keys for variable references in expressions too
tracing: Prevent hist_field_var_ref() from accessing NULL tracing_map_elts