[ Upstream commit 69f2c93463 ]
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea08aec7e7 upstream.
Commit 1527f69204 ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204 ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204 ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf476fe22a ]
In an unlikely (and probably wrong?) case that the 'ppi' parameter of
ata_host_alloc_pinfo() points to an array starting with a NULL pointer,
there's going to be a kernel oops as the 'pi' local variable won't get
reassigned from the initial value of NULL. Initialize 'pi' instead to
'&ata_dummy_port_info' to fix the possible kernel oops for good...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5399752299 ]
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ea23d5fa ]
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a66307d473 upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a8526a5cd upstream.
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Krzysztof Olędzki <ole@ans.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a6430ab9c upstream.
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 355a8031dc ]
The loop on entry of ata_host_start() may not initialize host->ops to a
non NULL value. The test on the host_stop field of host->ops must then
be preceded by a check that host->ops is not NULL.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-3-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Some functions have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 130f4caf14 ("libata: Ensure ata_port probe has completed before
detach") may cause system freeze during suspend.
Using async_synchronize_full() in PM callbacks is wrong, since async
callbacks that are already scheduled may wait for not-yet-scheduled
callbacks, causes a circular dependency.
Instead of using big hammer like async_synchronize_full(), use async
cookie to make sure port probe are synced, without affecting other
scheduled PM callbacks.
Fixes: 130f4caf14 ("libata: Ensure ata_port probe has completed before detach")
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: John Garry <john.garry@huawei.com>
BugLink: https://bugs.launchpad.net/bugs/1867983
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The docs toolchain doesn't recognise this pattern:
@link->[hw_]sata_spd_limit
As it can't really process it. So, instead, let's mark it with
a literal block markup:
``link->[hw_]sata_spd_limit``
in order to get rid of the following warning:
./drivers/ata/libata-core.c:5974: WARNING: Unknown target name: "hw".
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/9a21444df75c46095c4b1839d2061d19c9addcff.1586881715.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Start separating SATA specific code from libata-core.c:
* move following functions to libata-sata.c:
- ata_tf_to_fis()
- ata_tf_from_fis()
- sata_link_scr_lpm()
- ata_slave_link_init()
- sata_lpm_ignore_phy_events()
* group above functions together in <linux/libata.h>
* include libata-sata.c in the build when CONFIG_SATA_HOST=y
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36762 572 40 37374 91fe drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add !IS_ENABLED(CONFIG_SATA_HOST) to ata_dev_config_ncq() to allow
compiler to optimize out the function for non-SATA configs.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36462 572 40 37074 90d2 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Separate PATA timings code from libata-core.c:
* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) select it
* move following PATA timings code to libata-pata-timings.c:
- ata_timing_quantize()
- ata_timing_merge()
- ata_timing_find_mode()
- ata_timing_compute()
* group above functions together in <linux/libata.h>
* include libata-pata-timings.c in the build when PATA_TIMINGS
config option is enabled
* cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it
depends on code from libata-core.c and libata-pata-timings.c
while its only user is ATA ACPI)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
after:
37820 572 40 38432 9620 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* fix the overly long line in ata_timing_quantize()
* use standard kernel CodingStyle in ata_timing_merge()
* do not use assignment in if condition in ata_timing_compute()
* fix non-standard comment style in ata_timing_compute()
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move EXPORT_SYMBOL_GPL()s close to exported code like it is
done in other kernel subsystems. As a nice side effect this
results in the removal of few ifdefs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Optimize struct ata_force_param size by:
- using u8 for cbl and spd_limit fields
- using u16 for lflags field
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
after:
40654 573 40 41267 a133 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use COMMAND_LINE_SIZE instead PAGE_SIZE for ata_force_param_buf[]
size as libata parameters buffer doesn't need to be bigger than
the command line buffer.
For many architectures this results in decreased libata-core.o
size (COMMAND_LINE_SIZE varies from 256 to 4096 while the minimum
PAGE_SIZE is 4096).
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 4413 40 45517 b1cd drivers/ata/libata-core.o
after:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In commit 7634ccd2da ("libata: maintainership update") from 2018
Jens has officially taken over libata maintainership from Tejun so
remove stale information from core libata code.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
device_shutdown() called from reboot or power_shutdown expect
all devices to be shutdown. Same is true for even ahci pci driver.
As no ahci shutdown function is implemented, the ata subsystem
always remains alive with DMA & interrupt support. File system
related calls should not be honored after device_shutdown().
So defining ahci pci driver shutdown to freeze hardware (mask
interrupt, stop DMA engine and free DMA resources).
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With CONFIG_DEBUG_TEST_DRIVER_REMOVE set, we may find the following WARN:
[ 23.452574] ------------[ cut here ]------------
[ 23.457190] WARNING: CPU: 59 PID: 1 at drivers/ata/libata-core.c:6676 ata_host_detach+0x15c/0x168
[ 23.466047] Modules linked in:
[ 23.469092] CPU: 59 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00010-g5b83fd27752b-dirty #296
[ 23.477776] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 23.486286] pstate: a0c00009 (NzCv daif +PAN +UAO)
[ 23.491065] pc : ata_host_detach+0x15c/0x168
[ 23.495322] lr : ata_host_detach+0x88/0x168
[ 23.499491] sp : ffff800011cabb50
[ 23.502792] x29: ffff800011cabb50 x28: 0000000000000007
[ 23.508091] x27: ffff80001137f068 x26: ffff8000112c0c28
[ 23.513390] x25: 0000000000003848 x24: ffff0023ea185300
[ 23.518689] x23: 0000000000000001 x22: 00000000000014c0
[ 23.523987] x21: 0000000000013740 x20: ffff0023bdc20000
[ 23.529286] x19: 0000000000000000 x18: 0000000000000004
[ 23.534584] x17: 0000000000000001 x16: 00000000000000f0
[ 23.539883] x15: ffff0023eac13790 x14: ffff0023eb76c408
[ 23.545181] x13: 0000000000000000 x12: ffff0023eac13790
[ 23.550480] x11: ffff0023eb76c228 x10: 0000000000000000
[ 23.555779] x9 : ffff0023eac13798 x8 : 0000000040000000
[ 23.561077] x7 : 0000000000000002 x6 : 0000000000000001
[ 23.566376] x5 : 0000000000000002 x4 : 0000000000000000
[ 23.571674] x3 : ffff0023bf08a0bc x2 : 0000000000000000
[ 23.576972] x1 : 3099674201f72700 x0 : 0000000000400284
[ 23.582272] Call trace:
[ 23.584706] ata_host_detach+0x15c/0x168
[ 23.588616] ata_pci_remove_one+0x10/0x18
[ 23.592615] ahci_remove_one+0x20/0x40
[ 23.596356] pci_device_remove+0x3c/0xe0
[ 23.600267] really_probe+0xdc/0x3e0
[ 23.603830] driver_probe_device+0x58/0x100
[ 23.608000] device_driver_attach+0x6c/0x90
[ 23.612169] __driver_attach+0x84/0xc8
[ 23.615908] bus_for_each_dev+0x74/0xc8
[ 23.619730] driver_attach+0x20/0x28
[ 23.623292] bus_add_driver+0x148/0x1f0
[ 23.627115] driver_register+0x60/0x110
[ 23.630938] __pci_register_driver+0x40/0x48
[ 23.635199] ahci_pci_driver_init+0x20/0x28
[ 23.639372] do_one_initcall+0x5c/0x1b0
[ 23.643199] kernel_init_freeable+0x1a4/0x24c
[ 23.647546] kernel_init+0x10/0x108
[ 23.651023] ret_from_fork+0x10/0x18
[ 23.654590] ---[ end trace 634a14b675b71c13 ]---
With KASAN also enabled, we may also get many use-after-free reports.
The issue is that when CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, we may
attempt to detach the ata_port before it has been probed.
This is because the ata_ports are async probed, meaning that there is no
guarantee that the ata_port has probed prior to detach. When the ata_port
does probe in this scenario, we get all sorts of issues as the detach may
have already happened.
Fix by ensuring synchronisation with async_synchronize_full(). We could
alternatively use the cookie returned from the ata_port probe
async_schedule() call, but that means managing the cookie, so more
complicated.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are several firmware versions between version 2AR10001 and
2BA30001, presumably these also have broken FPDMA_AA activation, so
lets play it safe and apply the quirk to all firmware versions.
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We've received a bugreport that using LPM with ST1000LM024 drives leads
to system lockups. So it seems that these models are buggy in more then
1 way. Add NOLPM quirk to the existing quirks entry for BROKEN_FPDMA_AA.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
med_power_with_dipm still causes freezes after updating the firmware to
the latest version (DXT04L5Q).
Set model_rev to NULL and blacklist the device.
Cc: stable@vger.kernel.org
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
med_power_with_dipm causes my T450 to freeze with a SAMSUNG
MZ7TD256HAFV-000L9 SSD (firmware DXT02L5Q).
Switching the LPM to max_performance fixes this issue.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=z9pB
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180920' of git://git.kernel.dk/linux-block
Jens writes:
"Storage fixes for 4.19-rc5
- Fix for leaking kernel pointer in floppy ioctl (Andy Whitcroft)
- NVMe pull request from Christoph, and a single ANA log page fix
(Hannes)
- Regression fix for libata qd32 support, where we trigger an illegal
active command transition. This fixes a CD-ROM detection issue that
was reported, but could also trigger premature completion of the
internal tag (me)"
* tag 'for-linus-20180920' of git://git.kernel.dk/linux-block:
floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
libata: mask swap internal and hardware tag
nvme: count all ANA groups for ANA Log page
hen we're comparing the hardware completion mask passed in from the
driver with the internal tag pending mask, we need to account for the
fact that the internal tag is different from the hardware tag. If not,
then we can end up either prematurely completing the internal tag (since
it's not set in the hw mask), or simply flag an error:
ata2: illegal qc_active transition (100000000->00000001)
If the internal tag is set, then swap that with the hardware tag in this
case before comparing with what the hardware reports.
Fixes: 28361c4036 ("libata: add extra internal command")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201151
Cc: stable@vger.kernel.org
Reported-by: Paul Sbarra <sbarra.paul@gmail.com>
Tested-by: Paul Sbarra <sbarra.paul@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With gcc 4.1.2:
drivers/ata/libata-core.c:7396:33: warning: no newline at end of file
Fixes: 2fa4a32613 ("scsi: libsas: dynamically allocate and free ata host")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
Currently when min_power policy is selected, the partial low power state
is not entered and link will try aggressively enter to only slumber state.
Add a new policy which still enable DEVSLP but also try to enter partial
low power state. This policy is presented as "min_power_with_partial".
For information the difference between partial and slumber
Partial – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ns.
Slumber – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ms.
Devslp – PHY logic is powered down. The link PM exit latency from this
state to active state maximum is 20 ms, unless otherwise specified by
DETO.
Suggested-and-reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Defining `ATA_DEBUG` there are a lof of messages like below in the log.
[ 16.345472] ata_sg_setup: 1 sg elements mapped
As that is too verbose, only output these messages in verbose debug.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
