Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulator on pfuze100.
Based on Robin Gong's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Uncoupled regulators should be a special case of coupled regulators, so
they should share a common voltage setting path. When enabling,
disabling or setting voltage of a coupled regulator, all coupled
regulators should be locked. Regulator's supplies should be locked, when
setting voltage of a single regulator. Enabling a coupled regulator or
setting its voltage should not be possible if some of its coupled
regulators, has not been registered.
Add function for locking coupled regulators and supplies. Extract
a new function regulator_set_voltage_rdev() from
regulator_set_voltage_unlocked(), which is called when setting
voltage of a single regulator.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Introduce new function regulator_balance_voltage(), which
keeps max_spread constraint fulfilled between a group of coupled
regulators. It should be called if a regulator changes its
voltage or after disabling or enabling. Disabled regulators should
follow changes of the enabled ones, but their consumers' demands
shouldn't be taken into account while calculating voltage of other
coupled regulators.
Find voltages, which are closest to suiting all the consumers' demands,
while fulfilling max_spread constraint, keeping the following rules:
- if one regulator is about to rise its voltage, rise others
voltages in order to keep the max_spread
- if a regulator, which has caused rising other regulators, is
lowered, lower other regulators if possible
- if one regulator is about to lower its voltage, but it hasn't caused
rising other regulators, don't change its voltage if it breaks the
max_spread
Change regulators' voltages step by step, keeping max_spread constraint
fulfilled all the time. Function regulator_get_optimal_voltage()
should find the best possible change for the regulator, which doesn't
break max_spread constraint. In function regulator_balance_voltage()
optimize number of steps by finding highest voltage difference on
each iteration.
If a regulator, which is about to change its voltage, is not coupled,
method regulator_get_optimal_voltage() should simply return the lowest
voltage fulfilling consumers' demands.
Coupling should be checked only if the system is in PM_SUSPEND_ON state.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Fill coupling descriptor with data obtained from DTS using previously
defined of_functions. Fail to register a regulator, if some data
inconsistency occurs. If some coupled regulators are not yet registered,
don't fail to register, but try to resolve them in late init call.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Add new structure "coupling_desc" to regulator_dev, which contains
pointers to all coupled regulators including the owner of the structure,
number of coupled regulators and counter of currently resolved
regulators.
Add of_functions to parse all data needed in regulator coupling.
Provide method to check DTS data consistency. Check if each coupled
regulator's max_spread is equal and if their lists of regulators match.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators require keeping their voltage spread below defined
max_spread.
Add properties to provide information on regulators' coupling.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting voltage, enabling/disabling regulators requires operations on
all regulators related with the regulator being changed. Therefore,
all of them should be locked for the whole operation. With the current
locking implementation, adding additional dependency (regulators
coupling) causes deadlocks in some cases.
Introduce a possibility to attempt to lock a mutex multiple times
by the same task without waiting on a mutex. This should handle all
reasonable coupling-supplying combinations, especially when two coupled
regulators share common supplies. The only situation that should be
forbidden is simultaneous coupling and supplying between a pair of
regulators.
The idea is based on clk core.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up from the device tree configuration node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
We have augmented the GPIO core to look up the regulator special
GPIO "wlf,ldoena" in commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for configuring the machine constraints
valid_modes_mask element based on a list of allowed modes
specified via a device tree property.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a common device tree property for regulator nodes to support
the specification of allowed operating modes.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators attached via RPMh on Qualcomm sdm845 apparently are
write-only. Specifically you can send a request for a certain voltage
but you can't read back to see what voltage you've requested. What
this means is that at bootup we have absolutely no idea what voltage
we could be at.
As discussed in the patches to try to support the RPMh regulators [1],
the fact that regulators are write-only means that its driver's
get_voltage_sel() should return an error code if it's called before
any calls to set_voltage_sel(). This causes problems in
machine_constraints_voltage() when trying to apply the constraints.
A proposed fix was to come up with an error code that could be
returned by get_voltage_sel() which would cause the regulator
framework to simply try setting the voltage with the current
constraints.
In this patch I propose the error code -ENOTRECOVERABLE. In errno.h
this error is described as "State not recoverable". Though the error
code was originally intended "for robust mutexes", the description of
the error code seems to apply here because we can't read the state of
the regulator. Also note that the only existing user of this error
code in the regulator framework is tps65090-regulator.c which returns
this error code from the enable() call (not get_voltage() or
get_voltage_sel()), so there should be no existing regulators that
might accidentally get the new behavior. (Side note is that tps65090
seems to interpret this error code to mean an error that you can't
recover from rather than some data that can't be recovered).
[1] https://patchwork.kernel.org/patch/10340897/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8106A is an I2C attached single output regulator made by Silergy Corp,
which is used on several Allwinner H3/H5 SBCs to control the power
supply of the ARM cores.
Add a driver for it.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message, remove enable/disable code, add default
ramp_delay, add comment for go bit, add code for fixed mode voltage]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8106A is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.
Add its device tree binding.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message and slight fixes]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If device tree is not enabled, of_find_regulator_by_node() should have
a dummy function since the function call is still there.
This is to fix build error after CONFIG_NO_AUTO_INLINE is introduced.
If this option is enabled, GCC will not auto-inline functions that are
not explicitly marked as inline.
In this case (no CONFIG_OF), the copmiler will report error in function
regulator_dev_lookup().
W/O NO_AUTO_INLINE, function of_get_regulator() is auto-inlined and then
the call to of_find_regulator_by_node() is optimized out since
of_get_regulator() always return NULL.
W/ NO_AUTO_INLINE, the return value of of_get_regulator() is a variable
so the call to of_find_regulator_by_node() cannot be optimized out. So
we need a stub of_find_regulator_by_node().
static struct regulator_dev *regulator_dev_lookup(struct device *dev,
const char *supply)
{
struct regulator_dev *r = NULL;
struct device_node *node;
struct regulator_map *map;
const char *devname = NULL;
regulator_supply_alias(&dev, &supply);
/* first do a dt based lookup */
if (dev && dev->of_node) {
node = of_get_regulator(dev, supply);
if (node) {
r = of_find_regulator_by_node(node);
if (r)
return r;
...
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to Devicetree Specification v0.2 document:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."
Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD9571MWV PMIC supports backup mode, which keeps one or more DDR
rails powered while the main SoC is powered down.
Which DDR rails are to be kept powered is board-specific, and controlled
using the optional "rohm,ddr-backup-power" DT property. In the absence
of this property, backup mode is not available.
Backup mode can be enabled or disabled by the user using the standard
"wakeup" virtual file in sysfs, e.g. to enable:
echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup
When the PMIC is configured for backup mode, the role of the accessory
power switch changes from a power switch to a wake-up switch.
Two types of switches (or signals) can be used:
A. With a momentary power switch (or pulse signal), the PMIC is
configured for backup mode in the PMIC driver's suspend callback,
during system suspend.
Backup mode is enabled by default, as there is no further impact
during normal system operation.
B. With a toggle power switch (or level signal), the following steps
must be followed exactly:
1. Configure PMIC for backup mode,
2. Switch accessory power switch off, to prepare for system
suspend, which is a manual step not controlled by software,
3. Suspend system.
This mode is not yet supported by the driver.
As the switch type is board-specific, and cannot be determined
automatically, it is obtained from the presence of one of the
"rohm,rstbmode-*" properties in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable read/write access to the BD9571MWV_BKUP_MODE_CNT register, which
is amongst others used to configure DDR Backup Power.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add definitions for the KEEPON_* bits in the "BKUP Mode Cnt" register,
which control the DDR rails to be kept powered when backup mode is
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the new optional properties related to DDR Backup Mode and
toggle/momentary power switches.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the OTG VBus through N_VBUSEN PMIC pin.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems that the loop index i is not being incremented and hence
potentially the while loop could spin forever. Fortunately with the
data being used this does not appear to happen at the moment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In of_get_regulation_constraints() we were taking the result of
of_map_mode() (an unsigned int) and assigning it to an int. We were
then checking whether this value was -EINVAL. Some implementers of
of_map_mode() were returning -EINVAL (even though the return type of
their function needed to be unsigned int) because they needed to
signal an error back to of_get_regulation_constraints().
In general in the regulator framework the mode is always referred to
as an unsigned int. While we could fix this to be a signed int (the
highest value we store in there right now is 0x8), it's actually
pretty clean to just define the regulator mode 0x0 (the lack of any
bits set) as an invalid mode. Let's do that.
Fixes: 5e5e3a42c6 ("regulator: of: Add support for parsing initial and suspend modes")
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This version is exists in the Samsung Galaxy Tab 10.1 which is based on the
Nvidia Tegra 2 board. The TPS658624 has the same SM2 voltage table as
TPS658623.
Signed-off-by: ryang <decatf@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
pfuze3000 datasheet(Rev.9.0) from:
https://www.nxp.com/docs/en/data-sheet/PF3000.pdf
updates sw1a's voltage range, the settings for 1.450V and 1.475V
are replaced with 1.8V and 3.3V:
5b'11110 1.450 (SW1B), 1.8 (SW1A/SW1AB)
5b'11111 1.475 (SW1B), 3.3 (SW1A/SW1AB)
the voltage calculation using steps is NOT available for sw1a now,
use voltage table instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Buck10 is a multi(dual) phase regulator. So as part of enabling it
turn on the LP87565_BUCK_CTRL_1_FPWM_MP_0_2 bit which forces it to
operate always in multiphase and forced-PWM operation mode.
This helps improve the transient voltage response while switching OPP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The slew rate might need a +/- 15% margin as per the latest data manual:
http://www.ti.com/lit/ds/snvsb22/snvsb22.pdf
Hence take a conservative approach to program 85% of the original
hardware slew rate so that the software accommodates the margin
delay while voltage switching. Hence reduce the default ramp_delay
populated in the descriptors also by 15%.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=I0y0
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"We have queued a few more fixes (error handling, log replay,
softlockup) and the rest is SPDX updates that touche almost all files
so the diffstat is long"
* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Only check first key for committed tree blocks
btrfs: add SPDX header to Kconfig
btrfs: replace GPL boilerplate by SPDX -- sources
btrfs: replace GPL boilerplate by SPDX -- headers
Btrfs: fix loss of prealloc extents past i_size after fsync log replay
Btrfs: clean up resources during umount after trans is aborted
btrfs: Fix possible softlock on single core machines
Btrfs: bail out on error during replay_dir_deletes
Btrfs: fix NULL pointer dereference in log_dir_items
-----BEGIN PGP SIGNATURE-----
iQGwBAABCAAaBQJa0mDhExxzbWZyZW5jaEBnbWFpbC5jb20ACgkQiiy9cAdyT1HA
EQv+KxZAFONG/YGBIdoyJevnSobzZSTYgsrEmox28rIvWSFr6Xkt9K6WN4lki+Td
nacByZBhyeKPp7CxdgjmiNunbGfBZJsWk5LwtgdE2jOLjM9CFq8Z7m2qmkXQ4IkJ
EoH+NWpCUvEe9nj8oaTdSelR2OHH63SG5E5dK29eOB59ixcVe7qKUG29SpJks9qd
mCdZyhYyuzh469CKGFeQ8qfWopBH+QFBs4SrpQ9d4liNtZ3W8zTsQ3ezX069AGlU
Ef2xVTT1DtlZ4/6SiXBKlXGH3jjUg67vEGHzT3ZJwfLVNhTLEpKM/hsPiduSnjS8
JqdVRdFLc2lQzr4HknhNR9yuE5wT5tZM4iZOjNDwT6Sef2Mt0QIBuYI6kb4mv6Qg
aCVv7uXUMdvSrTk0mYiO1dXYozGUC+uFhJCuaiLax583o3ihp+/INDosQyqTbavZ
amRBZpWeNysSJwwJu21RdJiM74+fasR/CDy11U94ssxplg1qE72M8DShK7kXtUIy
g9ZW
=Ah5z
-----END PGP SIGNATURE-----
Merge tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"SMB3 fixes, a few for stable, and some important cleanup work from
Ronnie of the smb3 transport code"
* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: change validate_buf to validate_iov
cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
cifs: Change SMB2_open to return an iov for the error parameter
cifs: add resp_buf_size to the mid_q_entry structure
smb3.11: replace a 4 with server->vals->header_preamble_size
cifs: replace a 4 with server->vals->header_preamble_size
cifs: add pdu_size to the TCP_Server_Info structure
SMB311: Improve checking of negotiate security contexts
SMB3: Fix length checking of SMB3.11 negotiate request
CIFS: add ONCE flag for cifs_dbg type
cifs: Use ULL suffix for 64-bit constant
SMB3: Log at least once if tree connect fails during reconnect
cifs: smb2pdu: Fix potential NULL pointer dereference
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes. The status handling code is
actually a running regression from the previous merge window which had
an incomplete fix (now reverted) and most of the remaining bug fixes
are for problems older than the current merge window.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWtMW7SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYdtAP97FhqR
x2lDO7J6QT8hMVqwPeQS0Xh5ZPbZLedPmfx9BAD+K1HauGv8J/eMggMDPGrWa/CP
tGrg2UorMrokLLdIbyA=
=fOJs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
The status handling code is actually a running regression from the
previous merge window which had an incomplete fix (now reverted) and
most of the remaining bug fixes are for problems older than the
current merge window"
[ Side note: this merge also takes the base kernel git repository to 6+
million objects for the first time. Technically we hit it a couple of
merges ago already if you count all the tag objects, but now it
reaches 6M+ objects reachable from HEAD.
I was joking around that that's when I should switch to 5.0, because
3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
probably not, even if numerology is about as good a reason as any.
- Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
scsi: aacraid: Insure command thread is not recursively stopped
scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
scsi: qla2xxx: correctly shift host byte
scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
scsi: qla2xxx: Avoid double completion of abort command
scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
scsi: scsi_dh: Don't look for NULL devices handlers by name
scsi: core: remove redundant assignment to shost->use_blk_mq
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by
flex, bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by
flex, bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tD6R
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by flex,
bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by flex,
bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: extend output of 'listnewconfig'
kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
Kbuild: fix # escaping in .cmd files for future Make
kbuild: deb-pkg: split generating packaging and build
kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
kbuild: rename *-asn1.[ch] to *.asn1.[ch]
kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
.gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
kbuild: add %.dtb.S and %.dtb to 'targets' automatically
kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
genksyms: generate lexer and parser during build instead of shipping
kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
.gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
kbuild: use HOSTLDFLAGS for single .c executables
Pull x86 fixes from Thomas Gleixner:
"A set of fixes and updates for x86:
- Address a swiotlb regression which was caused by the recent DMA
rework and made driver fail because dma_direct_supported() returned
false
- Fix a signedness bug in the APIC ID validation which caused invalid
APIC IDs to be detected as valid thereby bloating the CPU possible
space.
- Fix inconsisten config dependcy/select magic for the MFD_CS5535
driver.
- Fix a corruption of the physical address space bits when encryption
has reduced the address space and late cpuinfo updates overwrite
the reduced bit information with the original value.
- Dominiks syscall rework which consolidates the architecture
specific syscall functions so all syscalls can be wrapped with the
same macros. This allows to switch x86/64 to struct pt_regs based
syscalls. Extend the clearing of user space controlled registers in
the entry patch to the lower registers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix signedness bug in APIC ID validity checks
x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
x86/olpc: Fix inconsistent MFD_CS5535 configuration
swiotlb: Use dma_direct_supported() for swiotlb_ops
syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
syscalls/core, syscalls/x86: Clean up syscall stub naming convention
syscalls/x86: Extend register clearing on syscall entry to lower registers
syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
x86/syscalls: Don't pointlessly reload the system call number
x86/mm: Fix documentation of module mapping range with 4-level paging
x86/cpuid: Switch to 'static const' specifier
Pull x86 pti updates from Thomas Gleixner:
"Another series of PTI related changes:
- Remove the manual stack switch for user entries from the idtentry
code. This debloats entry by 5k+ bytes of text.
- Use the proper types for the asm/bootparam.h defines to prevent
user space compile errors.
- Use PAGE_GLOBAL for !PCID systems to gain back performance
- Prevent setting of huge PUD/PMD entries when the entries are not
leaf entries otherwise the entries to which the PUD/PMD points to
and are populated get lost"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
x86/pti: Leave kernel text global for !PCID
x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
x86/pti: Enable global pages for shared areas
x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
x86/mm: Comment _PAGE_GLOBAL mystery
x86/mm: Remove extra filtering in pageattr code
x86/mm: Do not auto-massage page protections
x86/espfix: Document use of _PAGE_GLOBAL
x86/mm: Introduce "default" kernel PTE mask
x86/mm: Undo double _PAGE_PSE clearing
x86/mm: Factor out pageattr _PAGE_GLOBAL setting
x86/entry/64: Drop idtentry's manual stack switch for user entries
x86/uapi: Fix asm/bootparam.h userspace compilation errors
Pull scheduler fixes from Thomas Gleixner:
"A few scheduler fixes:
- Prevent a bogus warning vs. runqueue clock update flags in
do_sched_rt_period_timer()
- Simplify the helper functions which handle requests for skipping
the runqueue clock updat.
- Do not unlock the tunables mutex in the error path of the cpu
frequency scheduler utils. Its not held.
- Enforce proper alignement for 'struct util_est' in sched_avg to
prevent a misalignment fault on IA64"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Force proper alignment of 'struct util_est'
sched/core: Simplify helpers for rq clock update skip requests
sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
sched/cpufreq/schedutil: Fix error path mutex unlock
Pull more perf updates from Thomas Gleixner:
"A rather large set of perf updates:
Kernel:
- Fix various initialization issues
- Prevent creating [ku]probes for not CAP_SYS_ADMIN users
Tooling:
- Show only failing syscalls with 'perf trace --failure' (Arnaldo
Carvalho de Melo)
e.g: See what 'openat' syscalls are failing:
# perf trace --failure -e openat
762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
<SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
^C#
- Show information about the event (freq, nr_samples, total
period/nr_events) in the annotate --tui and --stdio2 'perf
annotate' output, similar to the first line in the 'perf report
--tui', but just for the samples for a the annotated symbol
(Arnaldo Carvalho de Melo)
- Introduce 'perf version --build-options' to show what features were
linked, aliased as well as a shorter 'perf -vv' (Jin Yao)
- Add a "dso_size" sort order (Kim Phillips)
- Remove redundant ')' in the tracepoint output in 'perf trace'
(Changbin Du)
- Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
Carvalho de Melo)
- Show group details on the title line in the annotate browser and
'perf annotate --stdio2' output, so that the per-event columns can
have headers (Arnaldo Carvalho de Melo)
- Fixup vertical line separating metrics from instructions and
cleaning unused lines at the bottom, both in the annotate TUI
browser (Arnaldo Carvalho de Melo)
- Remove duplicated 'samples' in lost samples warning in
'perf report' (Arnaldo Carvalho de Melo)
- Synchronize i915_drm.h, silencing the perf build process,
automagically adding support for the new DRM_I915_QUERY ioctl
(Arnaldo Carvalho de Melo)
- Make auxtrace_queues__add_buffer() allocate struct buffer, from a
patchkit already applied (Adrian Hunter)
- Fix the --stdio2/TUI annotate output to include group details, be
it for a recorded '{a,b,f}' explicit event group or when forcing
group display using 'perf report --group' for a set of events not
recorded as a group (Arnaldo Carvalho de Melo)
- Fix display artifacts in the ui browser (base class for the
annotate and main report/top TUI browser) related to the extra
title lines work (Arnaldo Carvalho de Melo)
- perf auxtrace refactorings, leftovers from a previously partially
processed patchset (Adrian Hunter)
- Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
Melo)
- Synchronize i915_drm.h, silencing a perf build warning and in the
process automagically adding support for a new ioctl command
(Arnaldo Carvalho de Melo)
- Fix a strncpy issue in uprobe tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
tracing/uprobe_event: Fix strncpy corner case
perf/core: Fix perf_uprobe_init()
perf/core: Fix perf_kprobe_init()
perf/core: Fix use-after-free in uprobe_perf_close()
perf tests clang: Fix function name for clang IR test
perf clang: Add support for recent clang versions
perf tools: Fix perf builds with clang support
perf tools: No need to include namespaces.h in util.h
perf hists browser: Remove leftover from row returned from refresh
perf hists browser: Show extra_title_lines in the 'D' debug hotkey
perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
tools headers uapi: Synchronize i915_drm.h
perf report: Remove duplicated 'samples' in lost samples warning
perf ui browser: Fixup cleaning unused lines at the bottom
perf annotate browser: Fixup vertical line separating metrics from instructions
perf annotate: Show group details on the title line
perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
perf/x86/intel: Move regs->flags EXACT bit init
perf trace: Remove redundant ')'
...
Pull x86 EFI bootup fixlet from Thomas Gleixner:
"A single fix for an early boot warning caused by invoking
this_cpu_has() before SMP initialization"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()
Pull irq affinity fixes from Thomas Gleixner:
- Fix error path handling in the affinity spreading code
- Make affinity spreading smarter to avoid issues on systems which
claim to have hotpluggable CPUs while in fact they can't hotplug
anything.
So instead of trying to spread the vectors (and thereby the
associated device queues) to all possibe CPUs, spread them on all
present CPUs first. If there are left over vectors after that first
step they are spread among the possible, but not present CPUs which
keeps the code backwards compatible for virtual decives and NVME
which allocate a queue per possible CPU, but makes the spreading
smarter for devices which have less queues than possible or present
CPUs.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Spread irq vectors among present CPUs as far as possible
genirq/affinity: Allow irq spreading from a given starting point
genirq/affinity: Move actual irq vector spreading into a helper function
genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
genirq/affinity: Don't return with empty affinity masks on error
Linus Walleij