commit 9d6803921a upstream.
Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.
This has been observed using the following setup:
|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0
The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.
This patch resolves the following warning on a non-patched kernel:
|[ 112.725394] ------------[ cut here ]------------
|[ 112.731418] WARNING: CPU: 1 PID: 257 at net/hsr/hsr_forward.c:560 hsr_forward_skb+0x484/0x568
|[ 112.739962] net/hsr/hsr_forward.c:560: Malformed frame (port_src hsr0)
The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1153a74768 upstream.
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4 ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b5674fe6b upstream.
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20 ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61431a5907 upstream.
Commit 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
packet_snd net/packet/af_packet.c:2994 [inline]
packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
kernel_sendpage net/socket.c:3628 [inline]
sock_sendpage+0xe5/0x140 net/socket.c:947
pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
splice_from_pipe_feed fs/splice.c:418 [inline]
__splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
splice_from_pipe fs/splice.c:597 [inline]
generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
do_splice_from fs/splice.c:767 [inline]
do_splice+0xb7e/0x1940 fs/splice.c:1079
__do_splice+0x134/0x250 fs/splice.c:1144
__do_sys_splice fs/splice.c:1350 [inline]
__se_sys_splice fs/splice.c:1332 [inline]
__x64_sys_splice+0x198/0x250 fs/splice.c:1332
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c84b33101 upstream.
In '4da6a196f93b1' we fixed a potential unhash loop caused when
a TLS socket in a sockmap was removed from the sockmap. This
happened because the unhash operation on the TLS ctx continued
to point at the sockmap implementation of unhash even though the
psock has already been removed. The sockmap unhash handler when a
psock is removed does the following,
void sock_map_unhash(struct sock *sk)
{
void (*saved_unhash)(struct sock *sk);
struct sk_psock *psock;
rcu_read_lock();
psock = sk_psock(sk);
if (unlikely(!psock)) {
rcu_read_unlock();
if (sk->sk_prot->unhash)
sk->sk_prot->unhash(sk);
return;
}
[...]
}
The unlikely() case is there to handle the case where psock is detached
but the proto ops have not been updated yet. But, in the above case
with TLS and removed psock we never fixed sk_prot->unhash() and unhash()
points back to sock_map_unhash resulting in a loop. To fix this we added
this bit of code,
static inline void sk_psock_restore_proto(struct sock *sk,
struct sk_psock *psock)
{
sk->sk_prot->unhash = psock->saved_unhash;
This will set the sk_prot->unhash back to its saved value. This is the
correct callback for a TLS socket that has been removed from the sock_map.
Unfortunately, this also overwrites the unhash pointer for all psocks.
We effectively break sockmap unhash handling for any future socks.
Omitting the unhash operation will leave stale entries in the map if
a socket transition through unhash, but does not do close() op.
To fix set unhash correctly before calling into tls_update. This way the
TLS enabled socket will point to the saved unhash() handler.
Fixes: 4da6a196f9 ("bpf: Sockmap/tls, during free we may call tcp_bpf_unhash() in loop")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/161731441904.68884.15593917809745631972.stgit@john-XPS-13-9370
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e5a03bcba upstream.
In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).
My patch adds a return when the skb was freed.
Fixes: bcf0cafab4 ("nfp: split out common control message handling code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a12f88361 upstream.
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7eeb52721 upstream.
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a91d3f02b upstream.
Add handling of allocation fault for ice_vsi_list_map_info.
Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.
Fixes: 9daf8208dd ("ice: Add support for switch filter programming")
Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com>
Co-developed-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88c529ac7 upstream.
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac8 ("ice: Add support for control queues")
Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08c27f3322 upstream.
KMSAN found uninitialized value at batadv_tt_prepare_tvlv_local_data()
[1], for commit ced72933a5 ("batman-adv: use CRC32C instead of CRC16
in TT code") inserted 'reserved' field into "struct batadv_tvlv_tt_data"
and commit 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN
specific") moved that field to "struct batadv_tvlv_tt_vlan_data" but left
that field uninitialized.
[1] https://syzkaller.appspot.com/bug?id=07f3e6dba96f0eb3cabab986adcd8a58b9bdbe9d
Reported-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: ced72933a5 ("batman-adv: use CRC32C instead of CRC16 in TT code")
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26c56ae67 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df41872b68 upstream.
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com
Fixes: b1058b9812 ("direct-io: submit bio after boundary buffer is added to it")
Signed-off-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bd070aae upstream.
The following deadlock is detected:
truncate -> setattr path is waiting for pending direct IO to be done (inode->i_dio_count become zero) with inode->i_rwsem held (down_write).
PID: 14827 TASK: ffff881686a9af80 CPU: 20 COMMAND: "ora_p005_hrltd9"
#0 __schedule at ffffffff818667cc
#1 schedule at ffffffff81866de6
#2 inode_dio_wait at ffffffff812a2d04
#3 ocfs2_setattr at ffffffffc05f322e [ocfs2]
#4 notify_change at ffffffff812a5a09
#5 do_truncate at ffffffff812808f5
#6 do_sys_ftruncate.constprop.18 at ffffffff81280cf2
#7 sys_ftruncate at ffffffff81280d8e
#8 do_syscall_64 at ffffffff81003949
#9 entry_SYSCALL_64_after_hwframe at ffffffff81a001ad
dio completion path is going to complete one direct IO (decrement
inode->i_dio_count), but before that it hung at locking inode->i_rwsem:
#0 __schedule+700 at ffffffff818667cc
#1 schedule+54 at ffffffff81866de6
#2 rwsem_down_write_failed+536 at ffffffff8186aa28
#3 call_rwsem_down_write_failed+23 at ffffffff8185a1b7
#4 down_write+45 at ffffffff81869c9d
#5 ocfs2_dio_end_io_write+180 at ffffffffc05d5444 [ocfs2]
#6 ocfs2_dio_end_io+85 at ffffffffc05d5a85 [ocfs2]
#7 dio_complete+140 at ffffffff812c873c
#8 dio_aio_complete_work+25 at ffffffff812c89f9
#9 process_one_work+361 at ffffffff810b1889
#10 worker_thread+77 at ffffffff810b233d
#11 kthread+261 at ffffffff810b7fd5
#12 ret_from_fork+62 at ffffffff81a0035e
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c0 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested]
Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com
Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3a8833dff upstream.
Commit cb9f753a37 ("mm: fix races between swapoff and flush dcache")
updated flush_dcache_page implementations on several architectures to
use page_mapping_file() in order to avoid races between page_mapping()
and swapoff().
This update missed arch/nds32 and there is a possibility of a race
there.
Replace page_mapping() with page_mapping_file() in nds32 implementation
of flush_dcache_page().
Link: https://lkml.kernel.org/r/20210330175126.26500-1-rppt@kernel.org
Fixes: cb9f753a37 ("mm: fix races between swapoff and flush dcache")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad1e36616 upstream.
ia64 has two stacks:
- memory stack (or stack), pointed at by by r12
- register backing store (register stack), pointed at by
ar.bsp/ar.bspstore with complications around dirty
register frame on CPU.
In [1] Dmitry noticed that PTRACE_GET_SYSCALL_INFO returns the register
stack instead memory stack.
The bug comes from the fact that user_stack_pointer() and
current_user_stack_pointer() don't return the same register:
ulong user_stack_pointer(struct pt_regs *regs) { return regs->ar_bspstore; }
#define current_user_stack_pointer() (current_pt_regs()->r12)
The change gets both back in sync.
I think ptrace(PTRACE_GET_SYSCALL_INFO) is the only affected user by
this bug on ia64.
The change fixes 'rt_sigreturn.gen.test' strace test where it was
observed initially.
Link: https://bugs.gentoo.org/769614 [1]
Link: https://lkml.kernel.org/r/20210331084447.2561532-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9562fd1329 upstream.
LLVM changed the expected function signature for llvm_gcda_emit_function()
in the clang-11 release. Users of clang-11 or newer may have noticed
their kernels producing invalid coverage information:
$ llvm-cov gcov -a -c -u -f -b <input>.gcda -- gcno=<input>.gcno
1 <func>: checksum mismatch, \
(<lineno chksum A>, <cfg chksum B>) != (<lineno chksum A>, <cfg chksum C>)
2 Invalid .gcda File!
...
Fix up the function signatures so calling this function interprets its
parameters correctly and computes the correct cfg checksum. In
particular, in clang-11, the additional checksum is no longer optional.
Link: https://reviews.llvm.org/rG25544ce2df0daa4304c07e64b9c8b0f7df60c11d
Link: https://lkml.kernel.org/r/20210408184631.1156669-1-ndesaulniers@google.com
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Tested-by: Prasad Sodagudi <psodagud@quicinc.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit b6a37a93c9 upstream.
intel_dsm_platform_mux_info() tries to parse the ACPI package data
from _DSM for the debug information, but it assumes the fixed format
without checking what values are stored in the elements actually.
When an unexpected value is returned from BIOS, it may lead to GPF or
NULL dereference, as reported recently.
Add the checks of the contents in the returned values and skip the
values for invalid cases.
v1->v2: Check the info contents before dereferencing, too
BugLink: http://bugzilla.opensuse.org/show_bug.cgi?id=1184074
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210402082317.871-1-tiwai@suse.de
(cherry picked from commit 337d7a1621)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6fdeb28f upstream.
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 864db232dc upstream.
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d120198bd5 upstream.
Unmask operation must be called with interrupt disabled,
on preempt_rt spin_lock_irqsave/spin_unlock_irqrestore
don't disable/enable interrupts, so use raw_* implementation
and change lock variable in struct irq_info from spinlock_t
to raw_spinlock_t
Cc: stable@vger.kernel.org
Fixes: 25da4618af ("xen/events: don't unmask an event channel when an eoi is pending")
Signed-off-by: Luca Fancellu <luca.fancellu@arm.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20210406105105.10141-1-luca.fancellu@arm.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5db93e7f upstream.
When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
sk->sk_node->next will point to itself, that will make an endless loop
and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
llcp_sock_connect() to avoid repeated invoking.
Fixes: b4011239a0 ("NFC: llcp: Fix non blocking sockets connections")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.11
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7574fcdbdc upstream.
In llcp_sock_connect(), use kmemdup to allocate memory for
"llcp_sock->service_name". The memory is not released in the sock_unlink
label of the subsequent failure branch.
As a result, memory leakage occurs.
fix CVE-2020-25672
Fixes: d646960f79 ("NFC: Initial LLCP support")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.3
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a4cd82d62 upstream.
nfc_llcp_local_get() is invoked in llcp_sock_connect(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25671
Fixes: c7aa12252f ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c33b1cc62a upstream.
nfc_llcp_local_get() is invoked in llcp_sock_bind(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25670
Fixes: c7aa12252f ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa65bacdb7 upstream.
The SST firmware's media and deep-buffer inputs are hardcoded to
S16LE, the corresponding DAIs don't have a hw_params callback and
their prepare callback also does not take the format into account.
So far the advertising of non working S24LE support has not caused
issues because pulseaudio defaults to S16LE, but changing pulse-audio's
config to use S24LE will result in broken sound.
Pipewire is replacing pulse now and pipewire prefers S24LE over S16LE
when available, causing the problem of the broken S24LE support to
come to the surface now.
Cc: stable@vger.kernel.org
BugLink: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/866
Fixes: 098c2cd281 ("ASoC: Intel: Atom: add 24-bit support for media playback and capture")
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210324132711.216152-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8426b2700 upstream.
We've got a report about Acer Aspire E1 (PCI SSID 1025:0840) that
loses the speaker output after resume. With the comparison of COEF
dumps, it was identified that the COEF 0x0d bits 0x6000 corresponds to
the speaker amp.
This patch adds the specific quirk for the device to restore the COEF
bits at the codec (re-)initialization.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1183869
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407095730.12560-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 168632a495 upstream.
Add a control to the card before copying the id so that the numid field
is initialized in the copy. Otherwise the numid field of active_id,
format_id, rate_id and channels_id will be the same (0) and
snd_ctl_notify() will not queue the events properly.
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407075428.2666787-1-jonashg@axis.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b14d72ac73 upstream
Ceiling value may be miss-aligned with what's actually configured into the
ARR register. This is seen after probe as currently the ARR value is zero,
whereas ceiling value is set to the maximum. So:
- reading ceiling reports zero
- in case the counter gets enabled without any prior configuration,
it won't count.
- in case the function gets set by the user 1st, (priv->ceiling) is used.
Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
the ARR register value directly by using regmap read or write when needed.
There should be no drawback on performance as priv->ceiling isn't used in
performance critical path.
There's also no point in writing ARR while setting function (sms), so
it can be safely removed.
Fixes: ad29937e20 ("counter: Add STM32 Timer quadrature encoder")
Suggested-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1614793789-10346-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[sudip: adjuct context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea29b20a82 upstream.
I read the commit log of the following two:
- bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML")
- 334ef6ed06 ("init/Kconfig: make COMPILE_TEST depend on !S390")
Both are talking about HAS_IOMEM dependency missing in many drivers.
So, 'depends on HAS_IOMEM' seems the direct, sensible solution to me.
This does not change the behavior of UML. UML still cannot enable
COMPILE_TEST because it does not provide HAS_IOMEM.
The current dependency for S390 is too strong. Under the condition of
CONFIG_PCI=y, S390 provides HAS_IOMEM, hence can enable COMPILE_TEST.
I also removed the meaningless 'default n'.
Link: https://lkml.kernel.org/r/20210224140809.1067582-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KP Singh <kpsingh@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Cc: Quentin Perret <qperret@google.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: "Enrico Weigelt, metux IT consult" <lkml@metux.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 334ef6ed06 upstream.
While allmodconfig and allyesconfig build for s390 there are also
various bots running compile tests with randconfig, where PCI is
disabled. This reveals that a lot of drivers should actually depend on
HAS_IOMEM.
Adding this to each device driver would be a never ending story,
therefore just disable COMPILE_TEST for s390.
The reasoning is more or less the same as described in
commit bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML").
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below patches caused a regression in a multipath setup:
Fixes: 9f98772ba3 ("nvme-rdma: fix controller reset hang during traffic")
Fixes: 2875b0aeca ("nvme-tcp: fix controller reset hang during traffic")
These patches on their own are correct because they fixed a controller reset
regression.
When we reset/teardown a controller, we must freeze and quiesce the namespaces
request queues to make sure that we safely stop inflight I/O submissions.
Freeze is mandatory because if our hctx map changed between reconnects,
blk_mq_update_nr_hw_queues will immediately attempt to freeze the queue, and
if it still has pending submissions (that are still quiesced) it will hang.
This is what the above patches fixed.
However, by freezing the namespaces request queues, and only unfreezing them
when we successfully reconnect, inflight submissions that are running
concurrently can now block grabbing the nshead srcu until either we successfully
reconnect or ctrl_loss_tmo expired (or the user explicitly disconnected).
This caused a deadlock [1] when a different controller (different path on the
same subsystem) became live (i.e. optimized/non-optimized). This is because
nvme_mpath_set_live needs to synchronize the nshead srcu before requeueing I/O
in order to make sure that current_path is visible to future (re)submisions.
However the srcu lock is taken by a blocked submission on a frozen request
queue, and we have a deadlock.
In recent kernels (v5.9+) direct_make_request was replaced by submit_bio_noacct
which does not have this issue because it bio_list will be active when
nvme-mpath calls submit_bio_noacct on the bottom device (because it was
populated when submit_bio was triggered on it.
Hence, we need to fix all the kernels that were before submit_bio_noacct was
introduced.
[1]:
Workqueue: nvme-wq nvme_tcp_reconnect_ctrl_work [nvme_tcp]
Call Trace:
__schedule+0x293/0x730
schedule+0x33/0xa0
schedule_timeout+0x1d3/0x2f0
wait_for_completion+0xba/0x140
__synchronize_srcu.part.21+0x91/0xc0
synchronize_srcu_expedited+0x27/0x30
synchronize_srcu+0xce/0xe0
nvme_mpath_set_live+0x64/0x130 [nvme_core]
nvme_update_ns_ana_state+0x2c/0x30 [nvme_core]
nvme_update_ana_state+0xcd/0xe0 [nvme_core]
nvme_parse_ana_log+0xa1/0x180 [nvme_core]
nvme_read_ana_log+0x76/0x100 [nvme_core]
nvme_mpath_init+0x122/0x180 [nvme_core]
nvme_init_identify+0x80e/0xe20 [nvme_core]
nvme_tcp_setup_ctrl+0x359/0x660 [nvme_tcp]
nvme_tcp_reconnect_ctrl_work+0x24/0x70 [nvme_tcp]
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26f55a59dc upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d4d45643 upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 219481a8f9 ]
Make SMB2 not print out an error when an oplock break is received for an
unknown handle, similar to SMB1. The debug message which is printed for
these unknown handles may also be misleading, so fix that too.
The SMB2 lease break path is not affected by this patch.
Without this, a program which writes to a file from one thread, and
opens, reads, and writes the same file from another thread triggers the
below errors several times a minute when run against a Samba server
configured with "smb2 leases = no".
CIFS: VFS: \\192.168.0.1 No task to wake, unknown frame received! NumMids 2
00000000: 424d53fe 00000040 00000000 00000012 .SMB@...........
00000010: 00000001 00000000 ffffffff ffffffff ................
00000020: 00000000 00000000 00000000 00000000 ................
00000030: 00000000 00000000 00000000 00000000 ................
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee8f4f6fc ]
RHBZ: 1933527
Under SMB1 + POSIX, if an inode is reused on a server after we have read and
cached a part of a file, when we then open the new file with the
re-cycled inode there is a chance that we may serve the old data out of cache
to the application.
This only happens for SMB1 (deprecated) and when posix are used.
The simplest solution to avoid this race is to force a revalidate
on smb1-posix open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a419cf49 ]
The sleep warning happens at early boot right at secondary CPU
activation bootup:
smp: Bringing up secondary CPUs ...
BUG: sleeping function called from invalid context at mm/page_alloc.c:4942
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.12.0-rc2-00007-g79e228d0b611-dirty #99
..
Call Trace:
show_stack+0x90/0xc0
dump_stack+0x150/0x1c0
___might_sleep+0x1c0/0x2a0
__might_sleep+0xa0/0x160
__alloc_pages_nodemask+0x1a0/0x600
alloc_page_interleave+0x30/0x1c0
alloc_pages_current+0x2c0/0x340
__get_free_pages+0x30/0xa0
ia64_mca_cpu_init+0x2d0/0x3a0
cpu_init+0x8b0/0x1440
start_secondary+0x60/0x700
start_ap+0x750/0x780
Fixed BSP b0 value from CPU 1
As I understand interrupts are not enabled yet and system has a lot of
memory. There is little chance to sleep and switch to GFP_ATOMIC should
be a no-op.
Link: https://lkml.kernel.org/r/20210315085045.204414-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36fa766faa ]
If pscsi_map_sg() fails, make sure to drop references to already allocated
bios.
Link: https://lore.kernel.org/r/20210323212431.15306-2-mwilck@suse.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fcb51c14d ]
The new Ubuntu GCC packages turn on -fcf-protection globally,
which causes a build failure in the x86 realmode code:
cc1: error: ‘-fcf-protection’ is not compatible with this target
Turn it off explicitly on compilers that understand this option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210323124846.1584944-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d677f12ea ]
On many recent ThinkPad laptops, there's a new LED next to the ESC key,
that indicates the FnLock status.
When the Fn+ESC combo is pressed, FnLock is toggled, which causes the
Media Key functionality to change, making it so that the media keys
either perform their media key function, or function as an F-key by
default. The Fn key can be used the access the alternate function at any
time.
With the current linux kernel, the LED doens't change state if you press
the Fn+ESC key combo. However, the media key functionality *does*
change. This is annoying, since the LED will stay on if it was on during
bootup, and it makes it hard to keep track what the current state of the
FnLock is.
This patch calls an ACPI function, that gets the current media key
state, when the Fn+ESC key combo is pressed. Through testing it was
discovered that this function causes the LED to update correctly to
reflect the current state when this function is called.
The relevant ACPI calls are the following:
\_SB_.PCI0.LPC0.EC0_.HKEY.GMKS: Get media key state, returns 0x603 if the FnLock mode is enabled, and 0x602 if it's disabled.
\_SB_.PCI0.LPC0.EC0_.HKEY.SMKS: Set media key state, sending a 1 will enable FnLock mode, and a 0 will disable it.
Relevant discussion:
https://bugzilla.kernel.org/show_bug.cgi?id=207841https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1881015
Signed-off-by: Esteve Varela Colominas <esteve.varela@gmail.com>
Link: https://lore.kernel.org/r/20210315195823.23212-1-esteve.varela@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad48d27a2 ]
We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause. Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9d36b061 ]
While passing the A530-specific lm_setup func to A530 and A540
to !A530 was fine back when only these two were supported, it
certainly is not a good idea to send A540 specifics to smaller
GPUs like A508 and friends.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 041c881a0b ]
Even if the first channel from sband channel list is invalid
or disabled mac80211 ends up choosing it as the default channel
for monitor interfaces, making them not usable.
Fix this by assigning the first available valid or enabled
channel instead.
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
Link: https://lore.kernel.org/r/1615440547-7661-1-git-send-email-kathirve@codeaurora.org
[reword commit message, comment, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
