This patch is written to clean up dependency of ARCH_EXYNOS
Not all exynos device have IRQ_COMBINER, especially aarch64 EXYNOS
but it is built for all exynos devices.
Thus add the config for EXYNOS_IRQ_COMBINER
remove direct dependency between ARCH_EXYNOS and exynos-combiner.c
and only selected on the aarch32 devices
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191224211108.7128-1-hyunki00.koo@gmail.com
The meson a1 Socs have some changes compared with previous
chips. For A113L, it contains 62 pins and can be spied on:
- 62:128 undefined
- 61:50 12 pins on bank A
- 49:37 13 pins on bank F
- 36:20 17 pins on bank X
- 19:13 7 pins on bank B
- 12:0 13 pins on bank P
There are five relative registers for gpio interrupt controller,
details are as below:
- PADCTRL_GPIO_IRQ_CTRL0
bit[31]: enable/disable the whole irq lines
bit[16-23]: both edge trigger
bit[8-15]: single edge trigger
bit[0-7]: pol trigger
- PADCTRL_GPIO_IRQ_CTRL[X]
bit[0-6]: 7 bits to choose gpio source for irq line 2*[X] - 2
bit[16-22]: 7 bits to choose gpio source for irq line 2*[X] - 1
where X =1,2,3,4
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191216123645.10099-4-qianggui.song@amlogic.com
Since Meson-A1 SoCs register layout of gpio interrupt controller has
difference with previous chips, registers to decide irq line and offset
of trigger method are all changed, the current driver should be modified.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191216123645.10099-3-qianggui.song@amlogic.com
Update dt-binding document for GPIO interrupt controller of Meson-A1 SoCs
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191216123645.10099-2-qianggui.song@amlogic.com
The following crash can be seen for setting
CONFIG_DEBUG_TEST_DRIVER_REMOVE=y for DT FW (which some people still use):
Hisilicon MBIGEN-V2 60080000.interrupt-controller: Failed to create mbi-gen irqdomain
Hisilicon MBIGEN-V2: probe of 60080000.interrupt-controller failed with error -12
[...]
Unable to handle kernel paging request at virtual address 0000000000005008
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000041fb9990000
[0000000000005008] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 5.5.0-rc6-00002-g3fc42638a506-dirty #1622
Hardware name: Huawei Taishan 2280 /D05, BIOS Hisilicon D05 IT21 Nemo 2.0 RC0 04/18/2018
pstate: 40000085 (nZcv daIf -PAN -UAO)
pc : mbigen_set_type+0x38/0x60
lr : __irq_set_trigger+0x6c/0x188
sp : ffff800014b4b400
x29: ffff800014b4b400 x28: 0000000000000007
x27: 0000000000000000 x26: 0000000000000000
x25: ffff041fd83bd0d4 x24: ffff041fd83bd188
x23: 0000000000000000 x22: ffff80001193ce00
x21: 0000000000000004 x20: 0000000000000000
x19: ffff041fd83bd000 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000
x15: ffff8000119098c8 x14: ffff041fb94ec91c
x13: ffff041fb94ec1a1 x12: 0000000000000030
x11: 0101010101010101 x10: 0000000000000040
x9 : 0000000000000000 x8 : ffff041fb98c6680
x7 : ffff800014b4b380 x6 : ffff041fd81636c8
x5 : 0000000000000000 x4 : 000000000000025f
x3 : 0000000000005000 x2 : 0000000000005008
x1 : 0000000000000004 x0 : 0000000080000000
Call trace:
mbigen_set_type+0x38/0x60
__setup_irq+0x744/0x900
request_threaded_irq+0xe0/0x198
pcie_pme_probe+0x98/0x118
pcie_port_probe_service+0x38/0x78
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
__device_attach_driver+0x90/0xb0
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x138
device_initial_probe+0x10/0x18
bus_probe_device+0x90/0x98
device_add+0x4c4/0x770
device_register+0x1c/0x28
pcie_port_device_register+0x1e4/0x4f0
pcie_portdrv_probe+0x34/0xd8
local_pci_probe+0x3c/0xa0
pci_device_probe+0x128/0x1c0
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
__device_attach_driver+0x90/0xb0
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x138
device_attach+0x10/0x18
pci_bus_add_device+0x4c/0xb8
pci_bus_add_devices+0x38/0x88
pci_host_probe+0x3c/0xc0
pci_host_common_probe+0xf0/0x208
hisi_pcie_almost_ecam_probe+0x24/0x30
platform_drv_probe+0x50/0xa0
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
device_driver_attach+0x6c/0x90
__driver_attach+0x84/0xc8
bus_for_each_dev+0x74/0xc8
driver_attach+0x20/0x28
bus_add_driver+0x148/0x1f0
driver_register+0x60/0x110
__platform_driver_register+0x40/0x48
hisi_pcie_almost_ecam_driver_init+0x1c/0x24
The specific problem here is that the mbigen driver real probe has failed
as the mbigen_of_create_domain()->of_platform_device_create() call fails,
the reason for that being that we never destroyed the platform device
created during the remove test dry run and there is some conflict.
Since we generally would never want to unbind this driver, and to save
adding a driver tear down path for that, just set the driver
.suppress_bind_attrs member to avoid this possibility.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1579196323-180137-1-git-send-email-john.garry@huawei.com
The Aspeed SOCs provide some interrupts through the System Control
Unit registers. Add an interrupt controller that provides these
interrupts to the system.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/1579123790-6894-3-git-send-email-eajames@linux.ibm.com
Document the Aspeed SCU interrupt controller and add an include file
for the interrupts it provides.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/1579123790-6894-2-git-send-email-eajames@linux.ibm.com
One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now.
-----BEGIN PGP SIGNATURE-----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=y3/O
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
-----BEGIN PGP SIGNATURE-----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=AIbz
-----END PGP SIGNATURE-----
Merge tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
-----BEGIN PGP SIGNATURE-----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=cuQx
-----END PGP SIGNATURE-----
Merge tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
An ino is unsigned, so display it as such in /proc/locks.
Cc: stable@vger.kernel.org
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e3f ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 6bd33e1ece ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Four fixes and one spelling update, all in drivers: 2 in lpfc and the
rest in mp3sas, cxgbi and target.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXgaIWSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishb2SAP45hS5T
owI8lIt+jMBnYG3k/66EleVdqMOcvtm9ewDN2gD/eW1LBz6uPzPn07gLB3V4TTTZ
rI8lfohhWJwRAHjvL8A=
=nxXW
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes and one spelling update, all in drivers: two in lpfc and
the rest in mp3sas, cxgbi and target"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target/iblock: Fix protection error with blocks greater than 512B
scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
scsi: lpfc: fix spelling mistakes of asynchronous
scsi: lpfc: fix build failure with DEBUGFS disabled
scsi: mpt3sas: Fix double free in attach error handling
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJeBmRZAAoJEAx081l5xIa++4AP/jxhA7ttHZ5yxMEJ4C34nOR7
SsrlF+utMXmtGBwqQ7NPM7rjg3fiz1O10n3kXcI5zuGkWU9B4wY5tioqu9lU0MHu
xQ2qoZH+z3ryKMkJGzKrRnlEKJk0LXQi/SjuuXSsVE6uwbzvtym4v6VFfXpBouQf
pR88u355xEB8Eij2Abi6yfHPW+GJjcvSz67K8/MYpMn9BUGcCliAGyij62UAl/FQ
tPXHHr0sdd6AAe6h7g7QqT40ELRiZI4rmjaIx35Kpe4K5v11+A8EHvHUzgHayDFW
FzNPr9s/fPD/3iAQMv7vKUp519jQy0tjMW6ad8uu0u9Qm341Qpm/NzSYQYpaKpi5
bNNAi6qQmruxk7vYnNNjIqm1zkIOCLPmb+psM9YEq3+To3ERrAKxfITOjA2Ae6bL
CBSSCUSQosWRfoIXSdeGUr0Urazs+wHJazIfSeGy/QrPYaYDw1jU2DQnFKMJuRMg
LmROAmX08hrG7/BBivMQeM5FftZOapyOZxzU1KBK94mKDwJWwFQO3Z4rk/rN1VKT
/ks5HO2FjTmeK+ffTsKG2INtvnpbawYoqVSVIR924JqcXBQSkyECneMTp3fS6zit
GbwSjvY0dsTaX1wejFg1waMu+N9CFccILduuv3B7Oa5hV1rDib1gJuBfw8VdTtLZ
t4EHAUwZyugUml3g7new
=pliy
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
This Kselftest update for Linux 5.5-rc4 consists of:
-- rseq build failures fixes related to glibc 2.30 compatibility
from Mathieu Desnoyers
-- Kunit fixes and cleanups from SeongJae Park
-- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
-----BEGIN PGP SIGNATURE-----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=ZztB
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- rseq build failures fixes related to glibc 2.30 compatibility from
Mathieu Desnoyers
- Kunit fixes and cleanups from SeongJae Park
- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Clarify rseq_prepare_unload() helper requirements
rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
rseq/selftests: Turn off timeout setting
kunit/kunit_tool_test: Test '--build_dir' option run
kunit: Rename 'kunitconfig' to '.kunitconfig'
kunit: Place 'test.log' under the 'build_dir'
kunit: Create default config in '--build_dir'
kunit: Remove duplicated defconfig creation
docs/kunit/start: Use in-tree 'kunit_defconfig'
selftests: livepatch: Fix it to do root uid check and skip
selftests: firmware: Fix it to do root uid check and skip
selftests: filesystems/epoll: fix build error
Fix compile test of the Tegra devfreq driver (Arnd Bergmann)
and remove redundant Kconfig dependencies from multiple devfreq
drivers (Leonard Crestez).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl4F2N4SHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRx7YcP/3TL0NX9bglMT/tZr9fulDuu1O5DFC2+
HuMqvwh7anx6Cf4YXksTuqGPeyQdxjx5xGnDm/FEKFV34nbBWwLfiRumG0UaaL24
g1kFYQDde79NI0oQ1vD0174Wwl5nutPE7QIyjl2ucrng7UjTaMhWccj7kprW8PMw
s+3EaHLuwU5LfECJ5CwjkhRW9rVugjEurfW7dButvPGsbxL1RTjreoU20IxDAbSm
DGc2qRvTpCIZI2fQQEc/fRttL51kfKpl1GZE2RGD3x9qorb6QGxyIbHnmMnUm7a1
8EHgVH4a5oRst1bnibLbSDCxGSuiTTX9HqgTsMYqdtDS2HuvTFhIpWZDy6QUZYNg
5EWeDRDeGNtI3Ctgh0/vdapiWvf02028VcQUQOZ+IIohzh1WIXBhI1OOvbd51UrJ
CmsQ8xjRIP0GHZfe5S+e0epCt6rLh4MsXNl9xc6UP4LtP7Yg0x3W0FiANe6ZJw2I
FxXKeRdv2DoYdV+vI9+WMXpdOb2A4kzkQ7hsbQ9sJboDSE32xbMcKFHLOgs2rYNd
hpELZwX4lZZfiHvLtUxc8omIFWLac+jnh/UsFJOcGqa2yA2/4ckrjMFMyIvgwRJz
Fo9xyzvWYGwDK/e70jfNbssd5RfmrX6QMI/283b1sYRK6BwRfgmU3oEWDwB35Esc
qv7in/zly5rZ
=EFpO
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
-----BEGIN PGP SIGNATURE-----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=L2kR
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Removal of now unused busy wqe list (Hillf)
- Add cond_resched() to io-wq work processing (Hillf)
- And then the series that I hinted at from last week, which removes
the sqe from the io_kiocb and keeps all sqe handling on the prep
side. This guarantees that an opcode can't do the wrong thing and
read the sqe more than once. This is unchanged from last week, no
issues have been observed with this in testing. Hence I really think
we should fold this into 5.5.
* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
io-wq: add cond_resched() to worker thread
io-wq: remove unused busy list from io_sqe
io_uring: pass in 'sqe' to the prep handlers
io_uring: standardize the prep methods
io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
io_uring: move all prep state for IORING_OP_CONNECT to prep handler
io_uring: add and use struct io_rw for read/writes
io_uring: use u64_to_user_ptr() consistently
-----BEGIN PGP SIGNATURE-----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=IO44
-----END PGP SIGNATURE-----
Merge tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block
Pull libata fixes from Jens Axboe:
"Two things in here:
- First half of a series that fixes ahci_brcm, also marked for
stable. The other part of the series is going into 5.6 (Florian)
- sata_nv regression fix that is also marked for stable (Sascha)"
* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
ata: ahci_brcm: Add missing clock management during recovery
ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
ata: ahci_brcm: Fix AHCI resources management
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
libata: Fix retrieving of active qcs
-----BEGIN PGP SIGNATURE-----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=UOAX
-----END PGP SIGNATURE-----
Merge tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which
is causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and
work properly.
- Fix the Kconfig on the Tegra driver.
-----BEGIN PGP SIGNATURE-----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=eZNi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae2 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f8297 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 6bb86fefa0
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Detailed description for this pull request:
1. Fix the build error of tegra*-devfreq.c when COMPILE_TEST is enableda
2. Drop unneeded PM_OPP dependency from each driver in Kconfig
-----BEGIN PGP SIGNATURE-----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=/ceh
-----END PGP SIGNATURE-----
Merge tag 'devfreq-fixes-for-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq fixes for 5.5-rc4 from Chanwoo Choi:
"1. Fix the build error of tegra*-devfreq.c when COMPILE_TEST is enabled.
2. Drop unneeded PM_OPP dependency from each driver in Kconfig."
* tag 'devfreq-fixes-for-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
Reschedule the current IO worker to cut the risk that it is becoming
a cpu hog.
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The rseq.h UAPI now documents that the rseq_cs field must be cleared
before reclaiming memory that contains the targeted struct rseq_cs, but
also that the rseq_cs field must be cleared before reclaiming memory of
the code pointed to by the rseq_cs start_ip and post_commit_offset
fields.
While we can expect that use of dlclose(3) will typically unmap
both struct rseq_cs and its associated code at once, nothing would
theoretically prevent a JIT from reclaiming the code without
reclaiming the struct rseq_cs, which would erroneously allow the
kernel to consider new code which is not a rseq critical section
as a rseq critical section following a code reclaim.
Suggested-by: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Florian Weimer <fw@deneb.enyo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
glibc 2.30 introduces gettid() in public headers, which clashes with
the internal static definition within rseq selftests.
Rename gettid() to rseq_gettid() to eliminate this symbol name clash.
Reported-by: Tommi T. Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Tommi T. Rantala <tommi.t.rantala@nokia.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
As the rseq selftests can run for a long period of time, disable the
timeout that the general selftests have.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This commit renames 'kunitconfig' to '.kunitconfig' so that it can be
automatically ignored by git and do not disturb people who want to type
'kernel/' by pressing only the 'k' and then 'tab' key.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'kunit' writes the 'test.log' under the kernel source directory even
though a 'build_dir' option is given. As users who use the option might
expect the outputs to be placed under the specified directory, this
commit modifies the logic to write the log file under the 'build_dir'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If both '--build_dir' and '--defconfig' are given, the handling of
'--defconfig' ignores '--build_dir' option. This commit modifies the
behavior to respect '--build_dir' option.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Suggested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'--defconfig' option is handled by the 'main() of the 'kunit.py' but
again handled in following 'run_tests()'. This commit removes this
duplicated handling of the option in the 'run_tests()'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kunit doc suggests users to get the default `kunitconfig` from an
external git tree. However, the file is already located under the
`arch/um/configs/` of the kernel tree. Because the local file is easier
to access and maintain, this commit updates the doc to use it.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
livepatch test configures the system and debug environment to run
tests. Some of these actions fail without root access and test
dumps several permission denied messages before it exits.
Fix test-state.sh to call setup_config instead of set_dynamic_debug
as suggested by Petr Mladek <pmladek@suse.com>
Fix it to check root uid and exit with skip code instead.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
firmware attempts to load test modules that require root access
and fail. Fix it to check for root uid and exit with skip code
instead.
Before this fix:
selftests: firmware: fw_run_tests.sh
modprobe: ERROR: could not insert 'test_firmware': Operation not permitted
You must have the following enabled in your kernel:
CONFIG_TEST_FIRMWARE=y
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_USER_HELPER=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
With this fix:
selftests: firmware: fw_run_tests.sh
skip all tests: must be run as root
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Reviwed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
epoll build fails to find pthread lib. Fix Makefile to use LDLIBS
instead of LDFLAGS. LDLIBS is the right flag to use here with -l
option when invoking ld.
gcc -I../../../../../usr/include/ -lpthread epoll_wakeup_test.c -o .../tools/testing/selftests/filesystems/epoll/epoll_wakeup_test
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `kill_timeout':
epoll_wakeup_test.c:(.text+0x4dd): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x4f2): undefined reference to `pthread_kill'
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `epoll9':
epoll_wakeup_test.c:(.text+0x6382): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x64d2): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6626): undefined reference to `pthread_join'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x684c): undefined reference to `pthread_tryjoin_np'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6864): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6878): undefined reference to `pthread_join'
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit e61df66c69 ("io-wq: ensure free/busy list browsing see all
items") added a list for io workers in addition to the free and busy
lists, not only making worker walk cleaner, but leaving the busy list
unused. Let's remove it.
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When listing a directory with thounsands of files and most of them are
reparse points, we simply marked all those dentries for revalidation
and then sending additional (compounded) create/getinfo/close requests
for each of them.
Instead, upon receiving a response from an SMB2_QUERY_DIRECTORY
(FileIdFullDirectoryInformation) command, the directory entries that
have a file attribute of FILE_ATTRIBUTE_REPARSE_POINT will contain an
EaSize field with a reparse tag in it, so we parse it and mark the
dentry for revalidation only if it is a DFS or a symlink.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
