Tests that permanent mdb entries can be added/deleted on ports with state down.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.
Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 05ca14fdb6.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jakub Kicinski says:
====================
docs: netdev: document more of our rules
The patch series length limit and reverse xmas tree are not documented.
Add those, and a tl;dr section summarizing how we differ.
v2: improve the series length blurb (Andrew)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Summarize the rules we see broken most often and which may
be less familiar to kernel devs who are used to working outside
of netdev.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the 15 patch rule the reverse xmas tree is not
documented.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had been asking people to avoid massive patch series but it does
not appear in the FAQ.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Unified bridge conversion - part 6/6
This is the sixth and final part of the conversion of mlxsw to the
unified bridge model. It transitions the last bits of functionality that
were under firmware's responsibility in the legacy model to the driver.
The last patches flip the driver to the unified bridge model and clean
up code that was used to make the conversion easier to review.
Patchset overview:
Patch #1 sets the egress VID for known unicast packets. For multicast
packets, the egress VID is configured using the MPE table. See commit
8c2da081c8 ("mlxsw: spectrum_fid: Configure egress VID classification
for multicast").
Patch #2 configures the VNI to FID classification that is used during
decapsulation.
Patch #3 configures ingress router interface (RIF) in FID classification
records, so that when a packet reaches the router block, its ingress RIF
is known. Care is taken to configure this in all the different flows
(e.g., RIF set on a FID, {Port, VID} joins a FID that already has a RIF
etc.).
Patch #4 configures the egress VID for routed packets. For such packets,
the egress VID is not set by the MPE table or by an FDB record at the
egress bridge, but instead by a dedicated table that maps {Egress RIF,
Egress port} to a VID.
Patch #5 removes VID configuration from RIF creation as in the unified
bridge model firmware no longer needs it.
Patch #6 sets the egress FID to use in RIF configuration so that the
device knows using which FID to bridge the packet after routing.
Patches #7-#9 add a new 802.1Q family and associated VLAN RIFs. In the
unified bridge model, we no longer need to emulate 802.1Q FIDs using
802.1D FIDs as VNI can be associated with both.
Patches #10-#11 finally flip the driver to the unified bridge model.
Patches #12-#13 clean up code that was used to make the conversion
easier to review.
v2:
* Fix build failure [1] in patch #1.
[1] https://lore.kernel.org/netdev/20220630201709.6e66a1bb@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some structures and defines were added with '_ub_' indication, as there
were equivalent objects for the legacy model.
Now when the legacy model is not used anymore, remove the '_ub_'
indication.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flood_index() function is not needed anymore, as in the unified
bridge model the flood index is calculated using 'mid_base' and
'fid_offset'.
Remove this function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After all the preparations for unified bridge model, finally flip mlxsw
driver to use the new model.
Change config profile, set 'ubridge' to true and remove the configurations
that are relevant only for the legacy model. Set 'flood_mode' to
'controlled' as the current mode is not supported with unified bridge
model.
Remove all the code which is dedicated to the legacy model. Remove
'struct mlxsw_sp.ubridge' variable which was temporarily added to separate
configurations between the models.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unified bridge model is enabled via the CONFIG_PROFILE command
during driver initialization. Add the definition of the relevant fields
to the command's payload in preparation for unified bridge enablement.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the legacy bridge model, there is no VID classification at egress
for 802.1Q FIDs, which means that the VID is maintained.
This behavior cause the limitation that 802.1Q FIDs cannot work with VXLAN.
This limitation stems from the fact that a decapsulated VXLAN packet should
not contain a VLAN tag. If such a packet was to egress from a local port
using a 802.1Q FID, it would "maintain" its VLAN on egress, which is no
VLAN at all.
Currently 802.1Q FIDs are emulated in mlxsw driver using 802.1D FIDs. Using
unified bridge model, there is a FID->VID mapping, so it is possible to
stop emulating 802.1Q FIDs.
The main changes are:
1. Use 'SFGC.bridge_type' = 0, to separate between 802.1Q FIDs and
802.1D FIDs.
2. Use VLAN RIF instead of the emulated one (VLAN_EMU which is emulated
using FID RIF).
3. Create VID->FID mapping when the FID is created. Then when a new port
is mapped to the FID, if it not in virtual mode, no new mapping is
needed. Save the new port in 'port_vid_list', to be able to update a
RIF in all {Port, VID}->FID mappings in case that the port will be in
virtual mode later.
4. Add a dedicated operation function per FID family to update RIF for
VID->FID mappings. For 802.1d and rFID families, just return. For
802.1q family, handle the global mapping which is created for new 802.1q
FID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unified bridge model, mlxsw will no longer emulate 802.1Q FIDs
using 802.1D FIDs. The new FID table will look as follows:
+---------------+
| 802.1q FIDs | 4K entries
| [1..4094] |
+---------------+
| 802.1d FIDs | 1K entries
| [4095..5118] |
+---------------+
| Dummy FIDs | 1 entry
| [5119..5119] |
+---------------+
| rFIDs | 11K entries
| [5120..16383] |
+---------------+
In order to make the change easier to review, four new temporary FID
families will be added (e.g., MLXSW_SP_FID_TYPE_8021D_UB) and will not
be registered with the FID core until mlxsw is flipped to use the unified
bridge model.
Add .1d, rfid and dummy FID families for unified bridge, the next patch
will add .1q family separately as it requires more changes.
The following changes are required:
1. Add 'smpe_index_valid' field to 'struct mlxsw_sp_fid_family' and set
SFMR.smpe accordingly. SMPE index is reserved for rFIDs, as their
flooding is handled by firmware, and always reserved in Spectrum-1,
as it is configured as part of PGT table.
2. Add 'ubridge' field to 'struct mlxsw_sp_fid_family'. This field will
be removed later, use it in mlxsw_sp_fid_family_{register,unregister}()
to skip the registration / unregistration of the new families when the
legacy model is used.
3. Indexes - the start and end indexes of each FID family will need to be
changed according to the above diagram.
4. Add flood tables for unified bridge model, use 'fid_offset' as table
type, as in the new model the access to flood tables will be using
'fid_offset' calculation.
5. FID family operation changes:
a. rFID supposed to be created using SFMR, as it is not created by
firmware using unified bridge model.
b. port_vid_map() should perform SVFA for rFID, as the mapping is not
created by firmware using unified bridge model.
c. flood_index() is not aligned to the new model, as this function will
be removed later.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
'VLAN' type, whereas RIFs constructed on top of VLAN-unaware bridges are of
'FID' type.
Currently 802.1Q FIDs are emulated using 802.1D FIDs, therefore VLAN RIFs
are emulated using FID RIFs. As part of converting the driver to use
unified bridge model, 802.1Q FIDs and VLAN RIFs will be used.
The egress FID is required for VLAN RIFs in Spectrum-2 and above, but not
in Spectrum-1, as in Spectrum-1 the mapping for VLAN RIFs is VID->FID,
while in other ASICs it is FID->FID. The reason for the change is that it
is more scalable to reuse the FID->FID entry than creating multiple
{Port, VID}->FID entries for the router port. Use the existing operation
structure to separate the configuration between different ASICs.
Add support for VLAN RIFs, most of the configurations are same to FID
RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After routing, a packet needs to perform an L2 lookup using the DMAC it got
from the routing and a FID. In unified bridge model, the egress FID
configuration needs to be performed by software.
It is configured by RITR for both sub-port RIFs and FID RIFs. Currently
FID RIFs already configure eFID. Add eFID configuration for sub-port RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field 'vid' in RITR is reserved when unified bridge model is used
and the RIF's type is sub-port RIF. Instead, ingress VID is configured via
SVFA and egress VID is configured via REIV.
Set 'vid' to zero in RITR register for sub-port RIF when unified bridge
model is used.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via REIV
register.
The table needs to be updated in the following flows:
1. When a RIF is set on a FID, need to iterate over the FID's {Port, VID}
list and issue REIV write to map the {RIF, Port} to the given VID.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
need to issue REIV write with a single record to map the {RIF, Port}
to the given VID.
REIV register supports a simultaneous update of 256 ports, so use this
capability for the first flow.
Handle the two above mentioned flows.
Add mlxsw_sp_fid_evid_map() function to handle egress VID classification
for both unicast and multicast. Layer 2 multicast configuration is already
done in the driver, just move it to the new function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before layer 2 forwarding, the device classifies an incoming packet to
a FID. The classification is done based on one of the following keys:
1. FID
2. VNI (after decapsulation)
3. VID / {Port, VID}
After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that
needs to be routed will ingress the router block.
In the legacy model, when a RIF was created / destroyed, it was
firmware's responsibility to update it in the previously mentioned FID
classification records. In the unified bridge model, this responsibility
moved to software.
The third classification requires to iterate over the FID's {Port, VID}
list and issue SVFA write with the correct mapping table according to the
port's mode (virtual or not). We never map multiple VLANs to the same FID
using VID->FID mapping, so such a mapping needs to be performed once.
When a new FID classification entry is configured and the FID already has
a RIF, set the RIF as part of SVFA configuration.
The reverse needs to be done when clearing a RIF from a FID. Currently,
clearing is done by issuing mlxsw_sp_fid_rif_set() with a NULL RIF pointer.
Instead, introduce mlxsw_sp_fid_rif_unset().
Note that mlxsw_sp_fid_rif_set() is called after the RIF is fully
operational, so it conforms to the internal requirement regarding
SVFA.irif_v: "Must not be set for a non-enabled RIF".
Do not set the ingress RIF for rFIDs, as the {Port, VID}->rFID entry is
configured by firmware when legacy model is used, a next patch will
handle this configuration for rFIDs and unified bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new model, SFMR no longer configures both VNI->FID and FID->VNI
classifications, but only the later. The former needs to be configured via
SVFA.
Add SVFA configuration as part of vni_set() and vni_clear().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using unified bridge model, firmware no longer configures the egress VID
"under the hood" and moves this responsibility to software.
For layer 2, this means that software needs to determine the egress VID
for both unicast (i.e., FDB) and multicast (i.e., MDB and flooding) flows.
Unicast FDB records and unicast LAG FDB records have new fields - "set_vid"
and "vid", set them. For records which point to router port, do not set
these fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d5f9023fa6 ("can: bcm: delay release of struct bcm_op
after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two
synchronize_rcu() calls in bcm_release() (only once at socket close)
and in bcm_delete_rx_op() (called on removal of each single bcm_op).
Unfortunately this slow removal of the bcm_op's affects user space
applications like cansniffer where the modification of a filter
removes 2048 bcm_op's which blocks the cansniffer application for
40(!) seconds.
In commit 181d444790 ("can: gw: use call_rcu() instead of costly
synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls
with several call_rcu()'s to safely remove the data structures after
the removal of CAN ID subscriptions with can_rx_unregister() calls.
This patch adopts Erics approach for the can-bcm which should be
applicable since the removal of tasklet_kill() in bcm_remove_op() and
the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4.
Fixes: d5f9023fa6 ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4
Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Norbert Slusarek <nslusarek@gmx.net>
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c")
Fixes: db7be2cb87 ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Delete the node fixed clock managed by secure world with SCMI.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
LSE clock is provided by SCMI.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The peripheral clock of CEC is not LSE but CEC.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fixes stm32mp15*-scmi DTS files introduced in [1] to also access PWR
regulators through SCMI service. This is needed since enabling secure
only access to RCC clock and reset controllers also enables secure
access only on PWR voltage regulators reg11, reg18 and usb33 hence
these must also be accessed through SCMI Voltage Domain protocol.
This change applies on commit [2] that already corrects issues from
commit [1].
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: [1] https://lore.kernel.org/linux-arm-kernel/20220422150952.20587-7-alexandre.torgue@foss.st.com
Link: [2] https://lore.kernel.org/linux-arm-kernel/20220613071920.5463-1-alexandre.torgue@foss.st.com
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Looking at the conditional lock acquire functions in the kernel due to
the new sparse support (see commit 4a557a5d1a "sparse: introduce
conditional lock acquire function attribute"), it became obvious that
the lockref code has a couple of them, but they don't match the usual
naming convention for the other ones, and their return value logic is
also reversed.
In the other very similar places, the naming pattern is '*_and_lock()'
(eg 'atomic_put_and_lock()' and 'refcount_dec_and_lock()'), and the
function returns true when the lock is taken.
The lockref code is superficially very similar to the refcount code,
only with the special "atomic wrt the embedded lock" semantics. But
instead of the '*_and_lock()' naming it uses '*_or_lock()'.
And instead of returning true in case it took the lock, it returns true
if it *didn't* take the lock.
Now, arguably the reflock code is quite logical: it really is a "either
decrement _or_ lock" kind of situation - and the return value is about
whether the operation succeeded without any special care needed.
So despite the similarities, the differences do make some sense, and
maybe it's not worth trying to unify the different conditional locking
primitives in this area.
But while looking at this all, it did become obvious that the
'lockref_get_or_lock()' function hasn't actually had any users for
almost a decade.
The only user it ever had was the shortlived 'd_rcu_to_refcount()'
function, and it got removed and replaced with 'lockref_get_not_dead()'
back in 2013 in commits 0d98439ea3 ("vfs: use lockred 'dead' flag to
mark unrecoverably dead dentries") and e5c832d555 ("vfs: fix dentry
RCU to refcounting possibly sleeping dput()")
In fact, that single use was removed less than a week after the whole
function was introduced in commit b3abd80250 ("lockref: add
'lockref_get_or_lock() helper") so this function has been around for a
decade, but only had a user for six days.
Let's just put this mis-designed and unused function out of its misery.
We can think about the naming and semantic oddities of the remaining
'lockref_put_or_lock()' later, but at least that function has users.
And while the naming is different and the return value doesn't match,
that function matches the whole '{atomic,refcount}_dec_and_test()'
pattern much better (ie the magic happens when the count goes down to
zero, not when it is incremented from zero).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes duplicate includes in the sc7180-trogdor files, which
accidentally ended up disabling nodes intended to be enabled.
It corrects identifiers for CPU6/7 on MSM8994. On SM8450 the UFS node's
interconnects property is updated to match the #interconnect-cells,
avoiding sync_state issues and the GIC ITS is defined, to correct the
references from the PCIe nodes. On SDM845 the display subsystem's AHB
clock is corrected and on msm8992 devices, the supplies for lvs 1 and 2
are correctly specified.
Lastly, a welcome addition of Konrad as reviewer for the Qualcomm SoC.
-----BEGIN PGP SIGNATURE-----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=sObb
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+pwl
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DT fixes for v5.19
This removes duplicate includes in the sc7180-trogdor files, which
accidentally ended up disabling nodes intended to be enabled.
It corrects identifiers for CPU6/7 on MSM8994. On SM8450 the UFS node's
interconnects property is updated to match the #interconnect-cells,
avoiding sync_state issues and the GIC ITS is defined, to correct the
references from the PCIe nodes. On SDM845 the display subsystem's AHB
clock is corrected and on msm8992 devices, the supplies for lvs 1 and 2
are correctly specified.
Lastly, a welcome addition of Konrad as reviewer for the Qualcomm SoC.
* tag 'qcom-arm64-fixes-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: msm8992-*: Fix vdd_lvs1_2-supply typo
MAINTAINERS: Add myself as a reviewer for Qualcomm ARM/64 support
arm64: dts: qcom: sdm845: use dispcc AHB clock for mdss node
arm64: dts: qcom: sm8450 add ITS device tree node
arm64: dts: qcom: msm8994: Fix CPU6/7 reg values
arm64: dts: qcom: sm8450: fix interconnects property of UFS node
arm64: dts: qcom: Remove duplicate sc7180-trogdor include on lazor/homestar
Link: https://lore.kernel.org/r/20220703030208.408109-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The kernel tends to try to avoid conditional locking semantics because
it makes it harder to think about and statically check locking rules,
but we do have a few fundamental locking primitives that take locks
conditionally - most obviously the 'trylock' functions.
That has always been a problem for 'sparse' checking for locking
imbalance, and we've had a special '__cond_lock()' macro that we've used
to let sparse know how the locking works:
# define __cond_lock(x,c) ((c) ? ({ __acquire(x); 1; }) : 0)
so that you can then use this to tell sparse that (for example) the
spinlock trylock macro ends up acquiring the lock when it succeeds, but
not when it fails:
#define raw_spin_trylock(lock) __cond_lock(lock, _raw_spin_trylock(lock))
and then sparse can follow along the locking rules when you have code like
if (!spin_trylock(&dentry->d_lock))
return LRU_SKIP;
.. sparse sees that the lock is held here..
spin_unlock(&dentry->d_lock);
and sparse ends up happy about the lock contexts.
However, this '__cond_lock()' use does result in very ugly header files,
and requires you to basically wrap the real function with that macro
that uses '__cond_lock'. Which has made PeterZ NAK things that try to
fix sparse warnings over the years [1].
To solve this, there is now a very experimental patch to sparse that
basically does the exact same thing as '__cond_lock()' did, but using a
function attribute instead. That seems to make PeterZ happy [2].
Note that this does not replace existing use of '__cond_lock()', but
only exposes the new proposed attribute and uses it for the previously
unannotated 'refcount_dec_and_lock()' family of functions.
For existing sparse installations, this will make no difference (a
negative output context was ignored), but if you have the experimental
sparse patch it will make sparse now understand code that uses those
functions, the same way '__cond_lock()' makes sparse understand the very
similar 'atomic_dec_and_lock()' uses that have the old '__cond_lock()'
annotations.
Note that in some cases this will silence existing context imbalance
warnings. But in other cases it may end up exposing new sparse warnings
for code that sparse just didn't see the locking for at all before.
This is a trial, in other words. I'd expect that if it ends up being
successful, and new sparse releases end up having this new attribute,
we'll migrate the old-style '__cond_lock()' users to use the new-style
'__cond_acquires' function attribute.
The actual experimental sparse patch was posted in [3].
Link: https://lore.kernel.org/all/20130930134434.GC12926@twins.programming.kicks-ass.net/ [1]
Link: https://lore.kernel.org/all/Yr60tWxN4P568x3W@worktop.programming.kicks-ass.net/ [2]
Link: https://lore.kernel.org/all/CAHk-=wjZfO9hGqJ2_hGQG3U_XzSh9_XaXze=HgPdvJbgrvASfA@mail.gmail.com/ [3]
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexander Aring <aahringo@redhat.com>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix statfs blocking on background inode gc workers
- Fix some broken inode lock assertion code
- Fix xattr leaf buffer leaks when cancelling a deferred xattr update
operation
- Clean up xattr recovery to make it easier to understand.
- Fix xattr leaf block verifiers tripping over empty blocks.
- Remove complicated and error prone xattr leaf block bholding mess.
- Fix a bug where an rt extent crossing EOF was treated as "posteof"
blocks and cleaned unnecessarily.
- Fix a UAF when log shutdown races with unmount.
-----BEGIN PGP SIGNATURE-----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=8QeL
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.19-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"This fixes some stalling problems and corrects the last of the
problems (I hope) observed during testing of the new atomic xattr
update feature.
- Fix statfs blocking on background inode gc workers
- Fix some broken inode lock assertion code
- Fix xattr leaf buffer leaks when cancelling a deferred xattr update
operation
- Clean up xattr recovery to make it easier to understand.
- Fix xattr leaf block verifiers tripping over empty blocks.
- Remove complicated and error prone xattr leaf block bholding mess.
- Fix a bug where an rt extent crossing EOF was treated as "posteof"
blocks and cleaned unnecessarily.
- Fix a UAF when log shutdown races with unmount"
* tag 'xfs-5.19-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: prevent a UAF when log IO errors race with unmount
xfs: dont treat rt extents beyond EOF as eofblocks to be cleared
xfs: don't hold xattr leaf buffers across transaction rolls
xfs: empty xattr leaf header blocks are not corruption
xfs: clean up the end of xfs_attri_item_recover
xfs: always free xattri_leaf_bp when cancelling a deferred op
xfs: use invalidate_lock to check the state of mmap_lock
xfs: factor out the common lock flags assert
xfs: introduce xfs_inodegc_push()
xfs: bound maximum wait time for inodegc work
hasdata does not need to be initialized to zero. It will be assigned a
value in the following judgment conditions.
Signed-off-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmLBZ3sTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXe2oB/wJ1T3/1tZ0+Jx7Hk84MXUTO9W05KqH
sie+yehu9A5+RNlA6/zRJBEmA4pyvOjtN0qynh3f25LfIesxUC5Tma1Epzp/Gnay
cYBrypD2iKKMNpJoiBtVVXh6Kin7+5oSLr4zxeaYcXjGfUlPIOqMnrwbGu/5ZtMH
7FL092tkQ/S1j/LDTiZk+OdjpuaM9D/7Z0t0iJ6NJb70/VEk6K3bY5XdmjLayYIJ
IBmxBbUXvBevVRDiSyMqNzA+RzQ5egrTrE3gPZZPneISN3Qu6cG+5xUqYGOxyjrJ
hzinoC48wEEHEMAeiM28AXjv9voIPvSoqeOvgZmSS0JTkfPZqirYpdzd
=9458
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.20-20220703' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-07-03
this is a pull request of 15 patches for net-next/master.
The first 2 patches are by Max Staudt and add the can327 serial CAN
driver along with a new line discipline ID.
The next patch is by me an fixes a typo in the ctucanfd driver.
The last 12 patches are by Dario Binacchi and integrate slcan CAN
serial driver better into the existing CAN driver API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Insufficient validation of element datatype and length in
nft_setelem_parse_data(). At least commit 7d7402642e updates
maximum element data area up to 64 bytes when only 16 bytes
where supported at the time. Support for larger element size
came later in fdb9c405e3 though. Picking this older commit
as Fixes: tag to be safe than sorry.
2) Memleak in pipapo destroy path, reproducible when transaction
in aborted. This is already triggering in the existing netfilter
test infrastructure since more recent new tests are covering this
path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Mi Says:
==============
Remove dependency between sriov and eswitch mode
Currently, there are three eswitch modes, none, legacy and
switchdev. None is the default mode. And when disabling sriov,
current eswitch mode will be changed to none. This patchset
removes eswitch mode none and also removes dependency between
sriov and eswitch mode. With this patchset, there are two
behavior changes:
Original behavior
-----------------
- When driver is loaded without sriov enabled, none is the default
mode. But actually eswitch mode should be either legacy or
switchdev, so devlink will return unsupported when showing
eswitch mode.
- When disabling sriov in either legacy or switchdev mode, eswitch
mode will be changed to none.
New behavior
------------
- When driver is loaded, legacy will be the default mode.
- When disabling sriov in either legacy or switchdev mode, eswitch
mode will not be changed.
Jianbo Liu Says:
================
Add support offloading police action
This patchset supports offloading police action by flow meter ASO
object in hardware.
The first part is to add interfaces to create and destroy flow meter
ASO object, and modify meter parameters by ACCESS_ASO WQE. As multiple
objects are created at a time, and two meters are in one object,
bitmaps are used manage these meters in one creation.
Then the police action can be mapped to a meter by the action index.
After mlx5e tc action refactoring was merged and post_act table was
added, a simple tc flow with one police action is broken down into two
rules in hardware. One rule with the original match in the original
table, which performs a metadata rewrite and do metering, then jumps
to post_meter table. The second rule is placed in the post_act table
with all the actions left.
The rules in post_meter table match on the meter outcome. If the
outcome is GREEN, we merely jump back to the post_act table for
further processing. Otherwise, the outcome is RED, and we drop the
packet.
The last part is to support flow meter ASO object in sw steering.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmLAlVYACgkQSD+KveBX
+j4WIQgAlZ05LMUqBl+5qHy4sm1JCo9KkS8HuwmWH23OyRQy1thAozeK3oiJxoGB
K4LZMxiWCFTroNffPkBU2co+w1Y7ptXkcMkhXZ8dcrlTjaxqCM+HtZdJiu31ltZ/
IIgNbE73dMkjNBGqaCyWjzZtfOfuDbhq9cx7rntFelRZWNAXYpRpzZQ1Ioh0CDFL
y56b9nmtjPEgaIBmD5Jfv22eaQJ21u4Wk9lWZL3hkotYzmrAqyAXYNtaAhbMD4Dt
AxgwxcxO9vfEwxmdFNpE3FCN/0firkHL2jf356ff0DBWYSv3iXC0l2lL6YEQ8FCC
eND23Pih2mDi5GoUKsUJht6A5EBI0Q==
=u3de
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2022-06-29
Chris Mi Says:
==============
Remove dependency between sriov and eswitch mode
Currently, there are three eswitch modes, none, legacy and
switchdev. None is the default mode. And when disabling sriov,
current eswitch mode will be changed to none. This patchset
removes eswitch mode none and also removes dependency between
sriov and eswitch mode. With this patchset, there are two
behavior changes:
Original behavior
-----------------
- When driver is loaded without sriov enabled, none is the default
mode. But actually eswitch mode should be either legacy or
switchdev, so devlink will return unsupported when showing
eswitch mode.
- When disabling sriov in either legacy or switchdev mode, eswitch
mode will be changed to none.
New behavior
------------
- When driver is loaded, legacy will be the default mode.
- When disabling sriov in either legacy or switchdev mode, eswitch
mode will not be changed.
Jianbo Liu Says:
================
Add support offloading police action
This patchset supports offloading police action by flow meter ASO
object in hardware.
The first part is to add interfaces to create and destroy flow meter
ASO object, and modify meter parameters by ACCESS_ASO WQE. As multiple
objects are created at a time, and two meters are in one object,
bitmaps are used manage these meters in one creation.
Then the police action can be mapped to a meter by the action index.
After mlx5e tc action refactoring was merged and post_act table was
added, a simple tc flow with one police action is broken down into two
rules in hardware. One rule with the original match in the original
table, which performs a metadata rewrite and do metering, then jumps
to post_meter table. The second rule is placed in the post_act table
with all the actions left.
The rules in post_meter table match on the meter outcome. If the
outcome is GREEN, we merely jump back to the post_act table for
further processing. Otherwise, the outcome is RED, and we drop the
packet.
The last part is to support flow meter ASO object in sw steering.
Signed-off-by: David S. Miller <davem@davemloft.net>
Dario Binacchi says:
====================
This series originated as a result of CAN communication tests for an
application using the USBtin adapter (https://www.fischl.de/usbtin/).
The tests showed some errors but for the driver everything was ok.
Also, being the first time I used the slcan driver, I was amazed that
it was not possible to configure the bitrate via the ip tool.
For these two reasons, I started looking at the driver code and realized
that it didn't use the CAN network device driver interface.
Starting from these assumptions, I tried to:
- Use the CAN network device driver interface.
- Set the bitrate via the ip tool.
- Send the open/close command to the adapter from the driver.
- Add ethtool support to reset the adapter errors.
- Extend the protocol to forward the adapter CAN communication
errors and the CAN state changes to the netdev upper layers.
Except for the protocol extension patches (i. e. forward the adapter CAN
communication errors and the CAN state changes to the netdev upper
layers), the whole series has been tested under QEMU with Linux 4.19.208
using the USBtin adapter.
Testing the extension protocol patches requires updating the adapter
firmware. Before modifying the firmware I think it makes sense to know if
these extensions can be considered useful.
Before applying the series I used these commands:
slcan_attach -f -s6 -o /dev/ttyACM0
slcand ttyACM0 can0
ip link set can0 up
After applying the series I am using these commands:
slcan_attach /dev/ttyACM0
slcand ttyACM0 can0
ip link set dev can0 down
ip link set can0 type can bitrate 500000
ethtool --set-priv-flags can0 err-rst-on-open on
ip link set dev can0 up
Now there is a clearer separation between serial line and CAN,
but above all, it is possible to use the ip and ethtool commands
as it happens for any CAN device driver. The changes are backward
compatible, you can continue to use the slcand and slcan_attach
command options.
Changes in v5:
- Update the commit message.
- Restore the use of rtnl_lock() and rtnl_unlock().
Changes in v4:
- Move the patch in front of the patch "[v3,04/13] can: slcan: use CAN network device driver API".
- Add the CAN_BITRATE_UNSET (0) and CAN_BITRATE_UNKNOWN (-1U) macros.
- Simplify the bitrate check to dump it.
- Update the commit description.
- Update the commit description.
- Use the CAN_BITRATE_UNKNOWN macro.
- Use kfree_skb() instead of can_put_echo_skb() in the slc_xmit().
- Remove the `if (slcan_devs)' check in the slc_dealloc().
- Replace `sl->tty == NULL' with `!sl->tty'.
- Use CAN_BITRATE_UNSET (0) and CAN_BITRATE_UNKNOWN (-1U) macros.
- Don't reset the bitrate in ndo_stop() if it has been configured.
- Squashed to the patch [v3,09/13] can: slcan: send the close command to the adapter.
- Use the CAN_BITRATE_UNKNOWN macro.
- Add description of slc_bump_err() function.
- Remove check for the 'e' character at the beggining of the function.
It was already checked by the caller function.
- Protect decoding against the case the len value is longer than the
received data.
- Some small changes to make the decoding more readable.
- Increment all the error counters at the end of the function.
- Add description of slc_bump_state() function.
- Remove check for the 's' character at the beggining of the function.
It was already checked by the caller function.
- Protect decoding against the case the frame len is longer than the
received data (add SLC_STATE_FRAME_LEN macro).
- Set cf to NULL in case of alloc_can_err_skb() failure.
- Some small changes to make the decoding more readable.
- Use the character 'b' instead of 'f' for bus-off state.
Changes in v3:
- Increment the error counter in case of decoding failure.
- Replace (-1) with (-1U) in the commit description.
- Update the commit description.
- Remove the slc_do_set_bittiming().
- Set the bitrate in the ndo_open().
- Replace -1UL with -1U in setting a fake value for the bitrate.
- Drop the patch "can: slcan: simplify the device de-allocation".
- Add the patch "can: netlink: dump bitrate 0 if can_priv::bittiming.bitrate is -1U".
Changes in v2:
- Put the data into the allocated skb directly instead of first
filling the "cf" on the stack and then doing a memcpy().
- Move CAN_SLCAN Kconfig option inside CAN_DEV scope.
- Improve the commit message.
- Use the CAN framework support for setting fixed bit rates.
- Improve the commit message.
- Protect decoding against the case the len value is longer than the
received data.
- Continue error handling even if no skb can be allocated.
- Continue error handling even if no skb can be allocated.
====================
Link: https://lore.kernel.org/all/20220628163137.413025-1-dario.binacchi@amarulasolutions.com/
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the slcan driver to switch the
"err-rst-on-open" setting on and off.
"err-rst-on-open" on - Reset error states on opening command
"err-rst-on-open" off - Don't reset error states on opening command
(default)
The setting can only be changed if the interface is down:
ip link set dev can0 down
ethtool --set-priv-flags can0 err-rst-on-open {off|on}
ip link set dev can0 up
Link: https://lore.kernel.org/all/20220628163137.413025-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case the bitrate has been set via ip tool, this patch changes the
driver to send the open ("O\r") and close ("C\r) commands to the
adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It allows to set the bitrate via ip tool, as it happens for the other
CAN device drivers. It still remains possible to set the bitrate via
slcand or slcan_attach utilities. In case the ip tool is used, the
driver will send the serial command to the adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch for the upcoming support to change the
bitrate via ip tool, reset the adapter error states via the ethtool API
and, more generally, send commands to the adapter.
Since the close command (i. e. "C\r") will be sent in the ndo_stop()
where netif_running() returns false, a new flag bit (i. e. SLF_XCMD) for
serial transmission has to be added.
Link: https://lore.kernel.org/all/20220628163137.413025-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As suggested by commit [1], now the driver uses the functions and the
data structures provided by the CAN network device driver interface.
Currently the driver doesn't implement a way to set bitrate for SLCAN
based devices via ip tool, so you'll have to do this by slcand or
slcan_attach invocation through the -sX parameter:
- slcan_attach -f -s6 -o /dev/ttyACM0
- slcand -f -s8 -o /dev/ttyUSB0
where -s6 in will set adapter's bitrate to 500 Kbit/s and -s8 to
1Mbit/s.
See the table below for further CAN bitrates:
- s0 -> 10 Kbit/s
- s1 -> 20 Kbit/s
- s2 -> 50 Kbit/s
- s3 -> 100 Kbit/s
- s4 -> 125 Kbit/s
- s5 -> 250 Kbit/s
- s6 -> 500 Kbit/s
- s7 -> 800 Kbit/s
- s8 -> 1000 Kbit/s
In doing so, the struct can_priv::bittiming.bitrate of the driver is not
set and since the open_candev() checks that the bitrate has been set, it
must be a non-zero value, the bitrate is set to a fake value (-1U)
before it is called.
Using the rtnl_lock()/rtnl_unlock() functions has become a bit more
tricky as the register_candev() function indirectly calls rtnl_lock()
via register_netdev(). To avoid a deadlock it is therefore necessary to
call rtnl_unlock() before calling register_candev(). The same goes for
the unregister_candev() function.
[1] commit 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20220628163137.413025-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upcoming changes on slcan driver will require you to specify a bitrate
of value -1 to prevent the open_candev() from failing but at the same
time highlighting that it is a fake value. In this case the command
`ip --details -s -s link show' would print 4294967295 as the bitrate
value. The patch change this value in 0.
Link: https://lore.kernel.org/all/20220628163137.413025-5-dario.binacchi@amarulasolutions.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It is used successfully by most (if not all) CAN device drivers. It
allows to remove replicated code.
Link: https://lore.kernel.org/all/20220628163137.413025-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
New elements that reside in the clone are not released in case that the
transaction is aborted.
[16302.231754] ------------[ cut here ]------------
[16302.231756] WARNING: CPU: 0 PID: 100509 at net/netfilter/nf_tables_api.c:1864 nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[...]
[16302.231882] CPU: 0 PID: 100509 Comm: nft Tainted: G W 5.19.0-rc3+ #155
[...]
[16302.231887] RIP: 0010:nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[16302.231899] Code: f3 fe ff ff 41 55 41 54 55 53 48 8b 6f 10 48 89 fb 48 c7 c7 82 96 d9 a0 8b 55 50 48 8b 75 58 e8 de f5 92 e0 83 7d 50 00 74 09 <0f> 0b 5b 5d 41 5c 41 5d c3 4c 8b 65 00 48 8b 7d 08 49 39 fc 74 05
[...]
[16302.231917] Call Trace:
[16302.231919] <TASK>
[16302.231921] __nf_tables_abort.cold+0x23/0x28 [nf_tables]
[16302.231934] nf_tables_abort+0x30/0x50 [nf_tables]
[16302.231946] nfnetlink_rcv_batch+0x41a/0x840 [nfnetlink]
[16302.231952] ? __nla_validate_parse+0x48/0x190
[16302.231959] nfnetlink_rcv+0x110/0x129 [nfnetlink]
[16302.231963] netlink_unicast+0x211/0x340
[16302.231969] netlink_sendmsg+0x21e/0x460
Add nft_set_pipapo_match_destroy() helper function to release the
elements in the lookup tables.
Stefano Brivio says: "We additionally look for elements pointers in the
cloned matching data if priv->dirty is set, because that means that
cloned data might point to additional elements we did not commit to the
working copy yet (such as the abort path case, but perhaps not limited
to it)."
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
