Prior to commit 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi
interrupts"), the branch from hmi_exception_early() to hmi_exception_realmode()
was just a bl hmi_exception_realmode, which the linker would turn into a bl to
the local entry point of hmi_exception_realmode. This was broken when
CONFIG_RELOCATABLE=y because hmi_exception_realmode() is not in the low part of
the kernel text that is copied down to 0x0.
But in fixing that, we added a new bug on little endian kernels. Because the
branch is now a bctrl when CONFIG_RELOCATABLE=y, we branch to the global entry
point of hmi_exception_realmode(). The global entry point must be called with
r12 containing the address of hmi_exception_realmode(), because it uses that
value to calculate the TOC value (r2).
This may manifest as a checkstop, because we take a junk value from r12 which
came from HSRR1, add a small constant to it and then use that as the TOC
pointer. The HSRR1 value will have 0x9 as the top nibble, which puts it above
RAM and somewhere in MMIO space.
Fix it by changing the BRANCH_LINK_TO_FAR() macro to always use r12 to load the
label we're branching to. This means r12 will be setup correctly on LE, fixing
this bug, and r12 is also volatile across function calls on BE so it's a good
choice anyway.
Fixes: 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts")
Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we set a kprobe on a 'stdu' instruction on powerpc64, we see a kernel
OOPS:
Bad kernel stack pointer cd93c840 at c000000000009868
Oops: Bad kernel stack pointer, sig: 6 [#1]
...
GPR00: c000001fcd93cb30 00000000cd93c840 c0000000015c5e00 00000000cd93c840
...
NIP [c000000000009868] resume_kernel+0x2c/0x58
LR [c000000000006208] program_check_common+0x108/0x180
On a 64-bit system when the user probes on a 'stdu' instruction, the kernel does
not emulate actual store in emulate_step() because it may corrupt the exception
frame. So the kernel does the actual store operation in exception return code
i.e. resume_kernel().
resume_kernel() loads the saved stack pointer from memory using lwz, which only
loads the low 32-bits of the address, causing the kernel crash.
Fix this by loading the 64-bit value instead.
Fixes: be96f63375 ("powerpc: Split out instruction analysis part of emulate_step()")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
[mpe: Change log massage, add stable tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In crc32c_vpmsum() we call enable_kernel_altivec() without first
disabling preemption, which is not allowed:
WARNING: CPU: 9 PID: 2949 at ../arch/powerpc/kernel/process.c:277 enable_kernel_altivec+0x100/0x120
Modules linked in: dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c vmx_crypto ...
CPU: 9 PID: 2949 Comm: docker Not tainted 4.11.0-rc5-compiler_gcc-6.3.1-00033-g308ac7563944 #381
...
NIP [c00000000001e320] enable_kernel_altivec+0x100/0x120
LR [d000000003df0910] crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
Call Trace:
0xc138fd09 (unreliable)
crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
crc32c_vpmsum_update+0x3c/0x60 [crc32c_vpmsum]
crypto_shash_update+0x88/0x1c0
crc32c+0x64/0x90 [libcrc32c]
dm_bm_checksum+0x48/0x80 [dm_persistent_data]
sb_check+0x84/0x120 [dm_thin_pool]
dm_bm_validate_buffer.isra.0+0xc0/0x1b0 [dm_persistent_data]
dm_bm_read_lock+0x80/0xf0 [dm_persistent_data]
__create_persistent_data_objects+0x16c/0x810 [dm_thin_pool]
dm_pool_metadata_open+0xb0/0x1a0 [dm_thin_pool]
pool_ctr+0x4cc/0xb60 [dm_thin_pool]
dm_table_add_target+0x16c/0x3c0
table_load+0x184/0x400
ctl_ioctl+0x2f0/0x560
dm_ctl_ioctl+0x38/0x50
do_vfs_ioctl+0xd8/0x920
SyS_ioctl+0x68/0xc0
system_call+0x38/0xfc
It used to be sufficient just to call pagefault_disable(), because that
also disabled preemption. But the two were decoupled in commit 8222dbe21e
("sched/preempt, mm/fault: Decouple preemption from the page fault
logic") in mid 2015.
So add the missing preempt_disable/enable(). We should also call
disable_kernel_fp(), although it does nothing by default, there is a
debug switch to make it active and all enables should be paired with
disables.
Fixes: 6dd7a82cc5 ("crypto: powerpc - Add POWER8 optimised crc32c")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 4c6d9acce1 ("powerpc/mm: Add hooks for cxl") converted local
TLB invalidates to global if the cxl driver is active. This is necessary
because the CAPP snoops invalidations to forward them to the PSL on the
cxl adapter. However one path was forgotten. native_flush_hash_range()
still does local TLB invalidates, as found out the hard way recently.
This patch fixes it by following the same logic as previously: if the
cxl driver is active, the local TLB invalidates are 'upgraded' to
global.
Fixes: 4c6d9acce1 ("powerpc/mm: Add hooks for cxl")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the kernel is compiled to use 64bit ABIv2 the _GLOBAL() macro does
not include a global entry point. A function's global entry point is
used when the function is called from a different TOC context and in the
kernel this typically means a call from a module into the vmlinux (or
vice-versa).
There are a few exported asm functions declared with _GLOBAL() and
calling them from a module will likely crash the kernel since any TOC
relative load will yield garbage.
flush_icache_range() and flush_dcache_range() are both exported to
modules, and use the TOC, so must use _GLOBAL_TOC().
Fixes: 721aeaa9fd ("powerpc: Build little endian ppc64 kernel with ABIv2")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the past, there was only one load-with-reservation instruction,
lwarx, and if a program attempted a lwarx on a misaligned address, it
would take an alignment interrupt and the kernel handler would emulate
it as though it was lwzx, which was not really correct, but benign since
it is loading the right amount of data, and the lwarx should be paired
with a stwcx. to the same address, which would also cause an alignment
interrupt which would result in a SIGBUS being delivered to the process.
We now have 5 different sizes of load-with-reservation instruction. Of
those, lharx and ldarx cause an immediate SIGBUS by luck since their
entries in aligninfo[] overlap instructions which were not fixed up, but
lqarx overlaps with lhz and will be emulated as such. lbarx can never
generate an alignment interrupt since it only operates on 1 byte.
To straighten this out and fix the lqarx case, this adds code to detect
the l[hwdq]arx instructions and return without fixing them up, resulting
in a SIGBUS being delivered to the process.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023 ("powerpc: Setup in HFSCR for POWER8")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The changes to enable building with a separate output directory, in
commit a8ba798bc8 ("selftests: enable O and KBUILD_OUTPUT") broke
building the powerpc selftests on their own, eg:
$ cd tools/testing/selftests/powerpc; make
It was partially fixed in commit e53aff45c4 ("selftests: lib.mk Fix
individual test builds"), which defined OUTPUT for standalone tests. But
that only defines OUTPUT within the Makefile, the value is not exported
so sub-shells can't see it. We could export OUTPUT, but it's actually
cleaner to just expand the value of OUTPUT before we invoke the shell.
Fixes: a8ba798bc8 ("selftests: enable O and KBUILD_OUTPUT")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 65c059bcaa ("powerpc: Enable support for GCC plugins") enabled GCC
plugins on powerpc, but neglected to update the architecture list in the
docs. Rectify this.
Fixes: 65c059bcaa ("powerpc: Enable support for GCC plugins")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 3f91a89d42.
Now that we do have the machinery for using the radix MMU under a
hypervisor, the extra check and comment introduced in 3f91a89d42 are
no longer correct. The result is that when booted under a hypervisor
that only allows use of radix, we clear the MMU_FTR_TYPE_RADIX and
then set it again, and print a warning about ignoring the
disable_radix command line option, even though the command line does
not include "disable_radix".
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117 ("powerpc/kvm: make hypervisor state restore a function")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a boundary condition where in some cases an eeh event with state ==
pci_channel_io_perm_failure wont be passed on to a driver attached to
the virtual PCI device associated with a slice. This will happen in case
the slice just before (n-1) doesn't have any vPHB bus associated with
it, that results in an early return from cxl_pci_error_detected()
callback.
With state == pci_channel_io_perm_failure, the adapter will be removed
irrespective of the return value of cxl_vphb_error_detected(). So we now
always return PCI_ERS_RESULT_DISCONNECTED for this case i.e even if
the AFU isn't using a vPHB (currently returns PCI_ERS_RESULT_NONE).
Fixes: e4f5fc001a6("cxl: Do not create vPHB if there are no AFU configuration records")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Wire up statx() syscall
- Don't print a warning on memory hotplug when HPT resizing isn't available
Thanks to:
David Gibson, Chandan Rajendra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TfiW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"A couple of minor powerpc fixes for 4.11:
- wire up statx() syscall
- don't print a warning on memory hotplug when HPT resizing isn't
available
Thanks to: David Gibson, Chandan Rajendra"
* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Don't give a warning when HPT resizing isn't available
powerpc: Wire up statx() syscall
Pull parisc fixes from Helge Deller:
- Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
modules with CONFIG_MODVERSIONS.
- Dave Anglin optimized the cache flushing for vmap ranges.
- Arvind Yadav provided a fix for a potential NULL pointer dereference
in the parisc perf code (and some code cleanups).
- I wired up the new statx system call, fixed some compiler warnings
with the access_ok() macro and fixed shutdown code to really halt a
system at shutdown instead of crashing & rebooting.
* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix system shutdown halt
parisc: perf: Fix potential NULL pointer dereference
parisc: Avoid compiler warnings with access_ok()
parisc: Wire up statx system call
parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
parisc: support R_PARISC_SECREL32 relocation in modules
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.
In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute. Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.
Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds. Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
-----BEGIN PGP SIGNATURE-----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=lNoR
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull OpenRISC fixes from Stafford Horne:
"OpenRISC fixes for build issues that were exposed by kbuild robots
after 4.11 merge. All from allmodconfig builds. This includes:
- bug in the handling of 8-byte get_user() calls
- module build failure due to multile missing symbol exports"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: Export symbols needed by modules
openrisc: fix issue handling 8 byte get_user calls
openrisc: xchg: fix `computed is not used` warning
This fixes the following races:
1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:
if (!explicit &&
atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
ALUA_ACCESS_STATE_TRANSITION) {
and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.
2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.
To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.
Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If tcmu-runner is processing a STPG and needs to change the kernel's
ALUA state then we cannot use the same work queue for task management
requests and ALUA transitions, because we could deadlock. The problem
occurs when a STPG times out before tcmu-runner is able to
call into target_tg_pt_gp_alua_access_state_store->
core_alua_do_port_transition -> core_alua_do_transition_tg_pt ->
queue_work. In this case, the tmr is on the work queue waiting for
the STPG to complete, but the STPG transition is now queued behind
the waiting tmr.
Note:
This bug will also be fixed by this patch:
http://www.spinics.net/lists/target-devel/msg14560.html
which switches the tmr code to use the system workqueues.
For both, I am not sure if we need a dedicated workqueue since
it is not a performance path and I do not think we need WQ_MEM_RECLAIM
to make forward progress to free up memory like the block layer does.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We do not setup the LU group for pscsi devices, so if you write
a state to alua_access_state that will cause a transition you will
get a NULL pointer dereference.
This patch will fail attempts to try and transition the path
for backend devices that set the TRANSPORT_FLAG_PASSTHROUGH_ALUA
flag.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows passthrough backends to use the core/base LIO
ALUA setup and state checks, but still handle the execution of
commands.
This will allow the target_core_user module to execute STPG and RTPG
in userspace, and not have to duplicate the ALUA state checks, path
information (needed so we can check if command is executable on
specific paths) and setup (rtslib sets/updates the configfs ALUA
interface like it does for iblock or file).
For STPG, the target_core_user userspace daemon, tcmu-runner will
still execute the STPG, and to update the core/base LIO state it
will use the existing configfs interface. For RTPG, tcmu-runner
will loop over configfs and/or cache the state.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We only were returing failure if the last opt to be parsed failed.
This has a return failure when we first detect a failure.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcmu hard codes the hw_max_sectors to 128 which is a litle small.
Userspace uses the max_sectors to report the optimal IO size and
some initiators perform better with larger IOs (open-iscsi seems
to do better with 256 to 512 depending on the test).
(Fix do not display hw max sectors twice - MNC)
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All in-tree fabric drivers provide a tfo->check_stop_free(),
so there is no need to do the extra check within existing
transport_cmd_check_stop_to_fabric() code.
Just to be sure, add a check in target_fabric_tf_ops_check()
to notify any out-of-tree drivers that might be missing it.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On those parisc machines which don't provide a software power off
function, the system currently kills the init process at the end of a
shutdown and unexpectedly restarts insteads of halting.
Fix it by adding a loop which will not return.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.9+
Pull CPU hotplug fix from Thomas Gleixner:
"A single fix preventing the concurrent execution of the CPU hotplug
callback install/invocation machinery. Long standing bug caused by a
massive brain slip of that Gleixner dude, which went unnoticed for
almost a year"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Serialize callback invocations proper
- Fix breakage in the intel_pstate's debugfs interface for PID
controller tuning (Rafael Wysocki).
- Fix computations related to P-state limits in intel_pstate to
avoid excessive rounding errors leading to visible inaccuracies
(Srinivas Pandruvada, Rafael Wysocki).
- Add a missing newline to a message printed by one function in
the cpufreq core and clean up that function (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3eV8
-----END PGP SIGNATURE-----
Merge tag 'pm-4.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a few more intel_pstate issues and one small issue in the
cpufreq core.
Specifics:
- Fix breakage in the intel_pstate's debugfs interface for PID
controller tuning (Rafael Wysocki)
- Fix computations related to P-state limits in intel_pstate to avoid
excessive rounding errors leading to visible inaccuracies (Srinivas
Pandruvada, Rafael Wysocki)
- Add a missing newline to a message printed by one function in the
cpufreq core and clean up that function (Rafael Wysocki)"
* tag 'pm-4.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Fix and clean up show_cpuinfo_cur_freq()
cpufreq: intel_pstate: Avoid percentages in limits-related computations
cpufreq: intel_pstate: Correct frequency setting in the HWP mode
cpufreq: intel_pstate: Update pid_params.sample_rate_ns in pid_param_set()
* pm-cpufreq-fixes:
cpufreq: Fix and clean up show_cpuinfo_cur_freq()
* intel_pstate-fixes:
cpufreq: intel_pstate: Avoid percentages in limits-related computations
cpufreq: intel_pstate: Correct frequency setting in the HWP mode
cpufreq: intel_pstate: Update pid_params.sample_rate_ns in pid_param_set()
