[ Upstream commit 7386a559ca ]
In accordance with the DWC USB3 bindings the property is supposed to have
uint32 type. It's erroneous from the DT schema and driver points of view
to declare it as boolean. As Neil suggested set it to 0x20 so not break
the platform and to make the dtbs checker happy.
Link: https://lore.kernel.org/linux-usb/20201010224121.12672-16-Sergey.Semin@baikalelectronics.ru/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9baf7d6be7 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201210091756.18057-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9164910c5 ]
Indicated by AML code in ACPI table, the touchpad in-use could be found
on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And
which one is in-use can be determined by reading another address on the
I2C bus. Unfortunately, for DT boot, there is currently no support in
firmware to make this check and patch DT accordingly. This results in
a non-functional touchpad on those C630 devices with hid@2c.
As i2c-hid driver will stop probing the device if there is nothing on
the slave address, we can actually keep both devices enabled in DT, and
i2c-hid driver will only probe the existing one. The only problem is
that we cannot set up pinctrl in both device nodes, as two devices with
the same pinctrl will cause pin conflict that makes the second device
fail to probe. Let's move the pinctrl state up to parent node to solve
this problem. As the pinctrl state of parent node is already defined in
sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active
state added in there.
Fixes: 11d0e4f281 ("arm64: dts: qcom: c630: Polish i2c-hid devices")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6efac0173c ]
Commit 45c5775460 ("usb: ohci-omap: Fix descriptor conversion") tried to
fix all issues related to ohci-omap descriptor conversion, but a wrong
patch was applied, and one needed change to the OSK board file is still
missing. Fix that.
Fixes: 45c5775460 ("usb: ohci-omap: Fix descriptor conversion")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[aaro.koskinen@iki.fi: rebased and updated the changelog]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a50ea34d6d upstream.
No need to check the following endpoints after finding the endpoint
wanted to drop.
Fixes: 54f6a8af37 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612255104-5363-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54f6a8af37 upstream.
For those unchecked endpoints, we don't allocate bandwidth for
them, so no need free the bandwidth, otherwise will decrease
the allocated bandwidth.
Meanwhile use xhci_dbg() instead of dev_dbg() to print logs and
rename bw_ep_list_new as bw_ep_chk_list.
Fixes: 1d69f9d901 ("usb: xhci-mtk: fix unreleased bandwidth data")
Cc: stable <stable@vger.kernel.org>
Reviewed-and-tested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612159064-28413-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d69f9d901 upstream.
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e5a3c8284 upstream.
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3
core") introduced clock support and a new function named
dwc3_core_init_for_resume() which enables the clock before calling
dwc3_core_init() during resume as clocks get disabled during suspend.
Unfortunately in this commit the DWC3_GCTL_PRTCAP_OTG case was forgotten
and therefore during resume, a platform could call dwc3_core_init()
without re-enabling the clocks first, preventing to resume properly.
So update the resume path to call dwc3_core_init_for_resume() as it
should.
Fixes: fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
Cc: stable@vger.kernel.org
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Link: https://lore.kernel.org/r/20210125161934.527820-1-gary.bisson@boundarydevices.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f670e9f9c8 upstream.
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
[ 217.533022] dwc2 ff300000.usb: dwc2_hsotg_process_req_status: USB_REQ_GET_STATUS
[ 217.559003] Unable to handle kernel read from unreadable memory at virtual address 0000000000000088
...
[ 218.313189] Call trace:
[ 218.330217] ep_from_windex+0x3c/0x54
[ 218.348565] usb_gadget_giveback_request+0x10/0x20
[ 218.368056] dwc2_hsotg_complete_request+0x144/0x184
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Fixes: c6f5c050e2 ("usb: dwc2: gadget: add bi-directional endpoint support")
Cc: stable@vger.kernel.org
Reported-by: Gerhard Klostermeier <gerhard.klostermeier@syss.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210127103919.58215-1-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9917f0e3cd upstream.
Should clear the pipe running flag in usbhs_pkt_pop(). Otherwise,
we cannot use this pipe after dequeue was called while the pipe was
running.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Reported-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1612183640-8898-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8c6edfa3f upstream.
Some devices, such as the Winbond Electronics Corp. Virtual Com Port
(Vendor=0416, ProdId=5011), lockup when usb_set_interface() or
usb_clear_halt() are called. This device has only a single
altsetting, so it should not be necessary to call usb_set_interface().
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jeremy Figgins <kernel@jeremyfiggins.com>
Link: https://lore.kernel.org/r/YAy9kJhM/rG8EQXC@watson
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e1f4a2e11 upstream.
This code should return -ENOMEM if the allocation fails but it currently
returns success.
Fixes: 9b95236eeb ("usb: gadget: ether: allocate and init otg descriptor by otg capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKE9rqVuJEOUWpW@mwanda
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3241929b67 upstream.
Older ATF does not provide SMC call for USB 3.0 phy power on functionality
and therefore initialization of xhci-hcd is failing when older version of
ATF is used. In this case phy_power_on() function returns -EOPNOTSUPP.
[ 3.108467] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 3.117250] phy phy-d0018300.phy.0: phy poweron failed --> -95
[ 3.123465] xhci-hcd: probe of d0058000.usb failed with error -95
This patch introduces a new plat_setup callback for xhci platform drivers
which is called prior calling usb_add_hcd() function. This function at its
beginning skips PHY init if hcd->skip_phy_initialization is set.
Current init_quirk callback for xhci platform drivers is called from
xhci_plat_setup() function which is called after chip reset completes.
It happens in the middle of the usb_add_hcd() function and therefore this
callback cannot be used for setting if PHY init should be skipped or not.
For Armada 3720 this patch introduce a new xhci_mvebu_a3700_plat_setup()
function configured as a xhci platform plat_setup callback. This new
function calls phy_power_on() and in case it returns -EOPNOTSUPP then
XHCI_SKIP_PHY_INIT quirk is set to instruct xhci-plat to skip PHY
initialization.
This patch fixes above failure by ignoring 'not supported' error in
xhci-hcd driver. In this case it is expected that phy is already power on.
It fixes initialization of xhci-hcd on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for USB 3.0 phy power.
This is regression introduced in commit bd3d25b073 ("arm64: dts: marvell:
armada-37xx: link USB hosts with their PHYs") where USB 3.0 phy was defined
and therefore xhci-hcd on Espressobin with older ATF started failing.
Fixes: bd3d25b073 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
Cc: <stable@vger.kernel.org> # 5.1+: f768e71891: usb: host: xhci-plat: add priv quirk for skip PHY initialization
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # On R-Car
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # xhci-plat
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210201150803.7305-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43377df704 upstream.
Teraoka AD2000 uses the CP210x driver, but the chip VID/PID is
customized with 0988/0578. We need the driver to support the new
VID/PID.
Signed-off-by: Chenxin Jin <bg4akv@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 640f17c824 ]
create_worker() will already set the right affinity using
kthread_bind_mask(), this means only the rescuer will need to change
it's affinity.
Howveer, while in cpu-hot-unplug a regular task is not allowed to run
on online&&!active as it would be pushed away quite agressively. We
need KTHREAD_IS_PER_CPU to survive in that environment.
Therefore set the affinity after getting that magic flag.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lkml.kernel.org/r/20210121103506.826629830@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac687e6e8c ]
There is a need to distinguish geniune per-cpu kthreads from kthreads
that happen to have a single CPU affinity.
Geniune per-cpu kthreads are kthreads that are CPU affine for
correctness, these will obviously have PF_KTHREAD set, but must also
have PF_NO_SETAFFINITY set, lest userspace modify their affinity and
ruins things.
However, these two things are not sufficient, PF_NO_SETAFFINITY is
also set on other tasks that have their affinities controlled through
other means, like for instance workqueues.
Therefore another bit is needed; it turns out kthread_create_per_cpu()
already has such a bit: KTHREAD_IS_PER_CPU, which is used to make
kthread_park()/kthread_unpark() work correctly.
Expose this flag and remove the implicit setting of it from
kthread_create_on_cpu(); the io_uring usage of it seems dubious at
best.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lkml.kernel.org/r/20210121103506.557620262@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1239c139 ]
Add Alder Lake mobile CPU model number to Intel family.
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210121215004.11618-1-tony.luck@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 655cf86548 ]
This is basically a revert of commit 644592d328 ("objtool: Fail the
kernel build on fatal errors").
That change turned out to be more trouble than it's worth. Failing the
build is an extreme measure which sometimes gets too much attention and
blocks CI build testing.
These fatal-type warnings aren't yet as rare as we'd hope, due to the
ever-increasing matrix of supported toolchains/plugins and their
fast-changing nature as of late.
Also, there are more people (and bots) looking for objtool warnings than
ever before, so even non-fatal warnings aren't likely to be ignored for
long.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dc4a6d791 ]
When device is removed, we need to make sure the F/W won't send us
any more events because during the remove process we disable the
interrupts.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8abaf379b ]
Need to take the lower 32 bits of the driver's 64-bit idle mask and put
it in the legacy 32-bit variable that the userspace reads to know the
idle mask.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9354f1b421 ]
Driver does not zero some pci counters packets before sending
to FW. This causes an out of sync PI/CI between driver and FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b08d8c783 ]
[why]
Heavy corruption or blank screen reported on wake,
with 6k display connected and FEC enabled
[how]
When Disable/Enable stream for display pipes on HPDRX,
DC should take into account ODM split pipes.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74f865f14 ]
[Why & How]
These can differ per ASIC or not be present. Don't call the dcn20 ones
directly but rather the ones defined by the ASIC init table.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4716a7c50c ]
Why:
Function decide_dp_link_settings() loops infinitely when required bandwidth
can't be supported.
How:
Check the required bandwidth against verified_link_cap before trying to
find a link setting for it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bc3d461d0 ]
[Why]
When no displays are currently enabled, display driver should not
disallow PSTATE switching.
[How]
Allow PSTATE switching if either the active configuration supports it,
or there are no active displays.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901c1ec05e ]
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
does that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd3a44c06f ]
Newer binutils (>= 2.36) refuse to assemble lmw/stmw when building in
little endian mode. That breaks compilation of our alignment handler
test:
/tmp/cco4l14N.s: Assembler messages:
/tmp/cco4l14N.s:1440: Error: `lmw' invalid when little-endian
/tmp/cco4l14N.s:1814: Error: `stmw' invalid when little-endian
make[2]: *** [../../lib.mk:139: /output/kselftest/powerpc/alignment/alignment_handler] Error 1
These tests do pass on little endian machines, as the kernel will
still emulate those instructions even when running little
endian (which is arguably a kernel bug).
But we don't really need to test that case, so ifdef those
instructions out to get the alignment test building again.
Reported-by: Libor Pechacek <lpechacek@suse.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Libor Pechacek <lpechacek@suse.com>
Link: https://lore.kernel.org/r/20210119041800.3093047-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bffcd50778 ]
The function nvmet_execute_identify_ns() doesn't set the status if call
to nvmet_find_namespace() fails. In that case we set the status of the
request to the value return by the nvmet_copy_sgl().
Set the status to NVME_SC_INVALID_NS and adjust the code such that
request will have the right status on nvmet_find_namespace() failure.
Without this patch :-
NVME Identify Namespace 3:
nsze : 0
ncap : 0
nuse : 0
nsfeat : 0
nlbaf : 0
flbas : 0
mc : 0
dpc : 0
dps : 0
nmic : 0
rescap : 0
fpi : 0
dlfeat : 0
nawun : 0
nawupf : 0
nacwu : 0
nabsn : 0
nabo : 0
nabspf : 0
noiob : 0
nvmcap : 0
mssrl : 0
mcl : 0
msrc : 0
nsattr : 0
nvmsetid: 0
anagrpid: 0
endgid : 0
nguid : 00000000000000000000000000000000
eui64 : 0000000000000000
lbaf 0 : ms:0 lbads:0 rp:0 (in use)
With this patch-series :-
feb3b88b501e (HEAD -> nvme-5.11) nvmet: remove extra variable in identify ns
6302aa67210a nvmet: remove extra variable in id-desclist
ed57951da453 nvmet: remove extra variable in smart log nsid
be384b8c24dc nvmet: set right status on error in id-ns handler
NVMe status: INVALID_NS: The namespace or the format of that namespace is invalid(0xb)
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20d3bb92e8 ]
Since NVMe v1.4 the Controller Memory Buffer must be explicitly enabled
by the host.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[hch: avoid a local variable and add a comment]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ebbfe495e ]
Each name space has a request queue, if complete request long time,
multi request queues may have time out requests at the same time,
nvme_tcp_timeout will execute concurrently. Multi requests in different
request queues may be queued in the same tcp queue, multi
nvme_tcp_timeout may call nvme_tcp_stop_queue at the same time.
The first nvme_tcp_stop_queue will clear NVME_TCP_Q_LIVE and continue
stopping the tcp queue(cancel io_work), but the others check
NVME_TCP_Q_LIVE is already cleared, and then directly complete the
requests, complete request before the io work is completely canceled may
lead to a use-after-free condition.
Add a multex lock to serialize nvme_tcp_stop_queue.
Signed-off-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7674073b2e ]
A crash happens when inject completing request long time(nearly 30s).
Each name space has a request queue, when inject completing request long
time, multi request queues may have time out requests at the same time,
nvme_rdma_timeout will execute concurrently. Multi requests in different
request queues may be queued in the same rdma queue, multi
nvme_rdma_timeout may call nvme_rdma_stop_queue at the same time.
The first nvme_rdma_timeout will clear NVME_RDMA_Q_LIVE and continue
stopping the rdma queue(drain qp), but the others check NVME_RDMA_Q_LIVE
is already cleared, and then directly complete the requests, complete
request before the qp is fully drained may lead to a use-after-free
condition.
Add a multex lock to serialize nvme_rdma_stop_queue.
Signed-off-by: Chao Leng <lengchao@huawei.com>
Tested-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d6b1c95b9 ]
According to NVMe spec v1.4, section 8.3.1, the PRINFO bit and
the metadata size play a vital role in deteriming the host buffer size.
If PRIFNO bit is set and MS==8, the host doesn't add the metadata buffer,
instead the controller adds it.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cdc4a6950 ]
When the capacity of the disc is too large (assuming the 4.7G
specification), the disc (UDF file system) will be burned
multiple times in the windows (Multisession Usage). When the
remaining capacity of the CD is less than 300M (estimated
value, for reference only), open the CD in the Linux system,
the content of the CD is displayed as blank (the kernel will
say "No VRS found"). Windows can display the contents of the
CD normally.
Through analysis, in the "fs/udf/super.c": udf_check_vsd
function, the actual value of VSD_MAX_SECTOR_OFFSET may
be much larger than 0x800000. According to the current code
logic, it is found that the type of sbi->s_session is "__s32",
when the remaining capacity of the disc is less than 300M
(take a set of test values: sector=3154903040,
sbi->s_session=1540464, sb->s_blocksize_bits=11 ), the
calculation result of "sbi->s_session << sb->s_blocksize_bits"
will overflow. Therefore, it is necessary to convert the
type of s_session to "loff_t" (when udf_check_vsd starts,
assign a value to _sector, which is also converted in this
way), so that the result will not overflow, and then the
content of the disc can be displayed normally.
Link: https://lore.kernel.org/r/20210114075741.30448-1-changlianzhi@uniontech.com
Signed-off-by: lianzhi chang <changlianzhi@uniontech.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3a0828d4 ]
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764907293e ]
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b101dd2d22 ]
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 622d3b4e39 ]
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6020d534fa ]
This fixes strlen mismatch problems happening in some .write callbacks
of debugfs.
When trying to configure airtime_flags in debugfs, an error appeared:
ash: write error: Invalid argument
The error is returned from kstrtou16() since a wrong length makes it
miss the real end of input string. To fix this, use count as the string
length, and set proper end of string for a char buffer.
The debug print is shown - airtime_flags_write: count = 2, len = 8,
where the actual length is 2, but "len = strlen(buf)" gets 8.
Also cleanup the other similar cases for the sake of consistency.
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20210112032028.7482-1-shayne.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e38dffcd ]
Building with the Clang assembler shows the following warning:
arch/x86/kernel/ftrace_64.o: warning: objtool: missing symbol for insn at offset 0x16
The Clang assembler strips section symbols. That ends up giving
objtool's find_func_containing() much more test coverage than normal.
Turns out, find_func_containing() doesn't work so well for overlapping
symbols:
2: 000000000000000e 0 NOTYPE LOCAL DEFAULT 2 fgraph_trace
3: 000000000000000f 0 NOTYPE LOCAL DEFAULT 2 trace
4: 0000000000000000 165 FUNC GLOBAL DEFAULT 2 __fentry__
5: 000000000000000e 0 NOTYPE GLOBAL DEFAULT 2 ftrace_stub
The zero-length NOTYPE symbols are inside __fentry__(), confusing the
rbtree search for any __fentry__() offset coming after a NOTYPE.
Try to avoid this problem by not adding zero-length symbols to the
rbtree. They're rare and aren't needed in the rbtree anyway.
One caveat, this actually might not end up being the right fix.
Non-empty overlapping symbols, if they exist, could have the same
problem. But that would need bigger changes, let's see if we can get
away with the easy fix for now.
Reported-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcd7059abc ]
Instead of queueing jackpoll_work, runtime resume the codec to let it
use different jack detection methods based on jackpoll_interval.
This partially matches SOF driver's behavior with commit a6e7d0a4bd
("ALSA: hda: fix jack detection with Realtek codecs when in D3"), the
difference is SOF unconditionally resumes the codec.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-1-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6e3ae7672 ]
When ioread32() returns 0xFFFFFFFF, we should execute cleanup functions
like other error handling paths before returning.
Link: https://lore.kernel.org/r/20201225083520.22015-1-dinghao.liu@zju.edu.cn
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b0f16fa6 ]
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Link: https://lore.kernel.org/r/20201215194731.2326-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
