Parse the configuration of resilient nexthop groups to existing mlxsw
data structures. Unlike non-resilient groups, nexthops without a valid
MAC or router interface (RIF) are programmed with a trap action instead
of not being programmed at all.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The Open Routing (Open/R) network protocol netlink handler uses ID 99
- Will also add to `/etc/iproute2/rt_protos` once this is accepted
- For more information: https://github.com/facebook/openr
Signed-off-by: From: Cooper Lees <me@cooperlees.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enetc runs out of exact match entries for unicast address
filtering, it switches to an approach based on hash tables, where
multiple MAC addresses might end up in the same bucket.
However, the enetc_set_mac_ht_flt function currently depends on the
system endianness, because it interprets the 64-bit hash value as an
array of two u32 elements. Modify this to use lower_32_bits and
upper_32_bits.
Tested by forcing enetc to go into hash table mode by creating two
macvlan upper interfaces:
ip link add link eno0 address 00:01:02:03:00:00 eno0.0 type macvlan && ip link set eno0.0 up
ip link add link eno0 address 00:01:02:03:00:01 eno0.1 type macvlan && ip link set eno0.1 up
and verified that the same bit values are written to the registers
before and after:
enetc_sync_mac_filters: addr 00:00:80:00:40:10 exact match 0
enetc_sync_mac_filters: addr 00:00:00:00:80:00 exact match 0
enetc_set_mac_ht_flt: hash 0x80008000000000 UMHFR0 0x0 UMHFR1 0x800080
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC has a 64-entry hash table for VLAN RX filtering per Station
Interface, which is accessed through two 32-bit registers: VHFR0 holding
the low portion, and VHFR1 holding the high portion.
The enetc_set_vlan_ht_filter function looks at the pf->vlan_ht_filter
bitmap, which is fundamentally an unsigned long variable, and casts it
to a u32 array of two elements. It puts the first u32 element into VHFR0
and the second u32 element into VHFR1.
It is easy to imagine that this will not work on big endian systems
(although, yes, we have bigger problems, because currently enetc assumes
that the CPU endianness is equal to the controller endianness, aka
little endian - but let's assume that we could add a cpu_to_le32 in
enetc_wd_reg and a le32_to_cpu in enetc_rd_reg).
Let's use lower_32_bits and upper_32_bits which are designed to work
regardless of endianness.
Tested that both the old and the new method produce the same results:
$ ethtool -K eth1 rx-vlan-filter on
$ ip link add link eth1 name eth1.100 type vlan id 100
enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x20
enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x20
$ ip link add link eth1 name eth1.101 type vlan id 101
enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x30
enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x30
$ ip link add link eth1 name eth1.34 type vlan id 34
enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x0 VHFR1 0x34
enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x0 VHFR1 0x34
$ ip link add link eth1 name eth1.1024 type vlan id 1024
enetc_set_vlan_ht_filter: method 1: si_idx 0 VHFR0 0x1 VHFR1 0x34
enetc_set_vlan_ht_filter: method 2: si_idx 0 VHFR0 0x1 VHFR1 0x34
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memdup_user_nul() helper instead of open-coding to
simplify the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made changes to coding style as suggested by checkpatch.pl
changes are of the type:
space required before the open parenthesis '('
space required after that ','
Signed-off-by: Sai Kalyaan Palla <saikalyaan63@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wong Vee Khee says:
====================
Add support for Clause-45 PHY Loopback
This patch series add support for Clause-45 PHY loopback.
It involves adding a generic API in the PHY framework, which can be
accessed by all C45 PHY drivers using the .set_loopback callback.
Also, enable PHY loopback for the Marvell 88x3310/88x2110 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHY loopback for Marvell 88x2110 and Marvell 88x3310.
This allow user to perform PHY loopback test using ethtool selftest.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic code to enable C45 PHY loopback into the common phy-c45.c
file. This will allow C45 PHY drivers aceess this by setting
.set_loopback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sprintf() is declared with a restrict keyword to not allow input and
output to point to the same buffer:
lib/test_rhashtable.c: In function 'print_ht':
lib/test_rhashtable.c:504:4: error: 'sprintf' argument 3 overlaps destination object 'buff' [-Werror=restrict]
504 | sprintf(buff, "%s\nbucket[%d] -> ", buff, i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
lib/test_rhashtable.c:489:7: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
489 | char buff[512] = "";
| ^~~~
Rework this function to remember the last offset instead to
avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compile testing this driver on a platform on which probe() is
known to fail at compile time, gcc warns about the cgx_lmactype_string[]
array being uninitialized:
In function 'strncpy',
inlined from 'link_status_user_format' at /git/arm-soc/drivers/net/ethernet/marvell/octeontx2/af/cgx.c:838:2,
inlined from 'cgx_link_change_handler' at /git/arm-soc/drivers/net/ethernet/marvell/octeontx2/af/cgx.c:853:2:
include/linux/fortify-string.h:27:30: error: argument 2 null where non-null expected [-Werror=nonnull]
27 | #define __underlying_strncpy __builtin_strncpy
Address this by turning the runtime initialization into a fixed array,
which should also produce better code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross timestamping is supported on Integrated Ethernet Controller in
Intel SoC such as EHL and TGL with Always Running Timer.
The hardware cross-timestamp result is made available to
applications through the PTP_SYS_OFFSET_PRECISE ioctl which calls
stmmac_getcrosststamp().
Device time is stored in the MAC Auxiliary register. The 64-bit System
time (ART timestamp) is stored in registers that are only addressable
by using MDIO space.
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/maintaning/maintaining/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/procdure/procedure/
s/maintanance/maintenance/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/preceeds/precedes/ .....two different places
s/rsponse/response/
s/cetain/certain/
s/precison/precision/
Fix a sentence construction as per suggestion.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter: flowtable enhancements
[ This is v2 that includes documentation enhancements, including
existing limitations. This is a rebase on top on net-next. ]
The following patchset augments the Netfilter flowtable fastpath to
support for network topologies that combine IP forwarding, bridge,
classic VLAN devices, bridge VLAN filtering, DSA and PPPoE. This
includes support for the flowtable software and hardware datapaths.
The following pictures provides an example scenario:
fast path!
.------------------------.
/ \
| IP forwarding |
| / \ \/
| br0 wan ..... eth0
. / \ host C
-> veth1 veth2
. switch/router
.
.
eth0
host A
The bridge master device 'br0' has an IP address and a DHCP server is
also assumed to be running to provide connectivity to host A which
reaches the Internet through 'br0' as default gateway. Then, packet
enters the IP forwarding path and Netfilter is used to NAT the packets
before they leave through the wan device.
The general idea is to accelerate forwarding by building a fast path
that takes packets from the ingress path of the bridge port and place
them in the egress path of the wan device (and vice versa). Hence,
skipping the classic bridge and IP stack paths.
** Patch from #1 to #6 add the infrastructure which describes the list of
netdevice hops to reach a given destination MAC address in the local
network topology.
Patch #1 adds dev_fill_forward_path() and .ndo_fill_forward_path() to
netdev_ops.
Patch #2 adds .ndo_fill_forward_path for vlan devices, which provides
the next device hop via vlan->real_dev, the vlan ID and the
protocol.
Patch #3 adds .ndo_fill_forward_path for bridge devices, which allows to make
lookups to the FDB to locate the next device hop (bridge port) in the
forwarding path.
Patch #4 extends bridge .ndo_fill_forward_path to support for bridge VLAN
filtering.
Patch #5 adds .ndo_fill_forward_path for PPPoE devices.
Patch #6 adds .ndo_fill_forward_path for DSA.
Patches from #7 to #14 update the flowtable software datapath:
Patch #7 adds the transmit path type field to the flow tuple. Two transmit
paths are supported so far: the neighbour and the xfrm transmit
paths.
Patch #8 and #9 update the flowtable datapath to use dev_fill_forward_path()
to obtain the real ingress/egress device for the flowtable datapath.
This adds the new ethernet xmit direct path to the flowtable.
Patch #10 adds native flowtable VLAN support (up to 2 VLAN tags) through
dev_fill_forward_path(). The flowtable stores the VLAN id and
protocol in the flow tuple.
Patch #11 adds native flowtable bridge VLAN filter support through
dev_fill_forward_path().
Patch #12 adds native flowtable bridge PPPoE through dev_fill_forward_path().
Patch #13 adds DSA support through dev_fill_forward_path().
Patch #14 extends flowtable selftests to cover for flowtable software
datapath enhancements.
** Patches from #15 to #20 update the flowtable hardware offload datapath:
Patch #15 extends the flowtable hardware offload to support for the
direct ethernet xmit path. This also includes VLAN support.
Patch #16 stores the egress real device in the flow tuple. The software
flowtable datapath uses dev_hard_header() to transmit packets,
hence it might refer to VLAN/DSA/PPPoE software device, not
the real ethernet device.
Patch #17 deals with switchdev PVID hardware offload to skip it on
egress.
Patch #18 adds FLOW_ACTION_PPPOE_PUSH to the flow_offload action API.
Patch #19 extends the flowtable hardware offload to support for PPPoE
Patch #20 adds TC_SETUP_FT support for DSA.
** Patches from #20 to #23: Felix Fietkau adds a new driver which support
hardware offload for the mtk PPE engine through the existing flow
offload API which supports for the flowtable enhancements coming in
this batch.
Patch #24 extends the documentation and describe existing limitations.
Please, apply, thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the flowtable documentation to describe recent
enhancements:
- Offload action is available after the first packets go through the
classic forwarding path.
- IPv4 and IPv6 are supported. Only TCP and UDP layer 4 are supported at
this stage.
- Tuple has been augmented to track VLAN id and PPPoE session id.
- Bridge and IP forwarding integration, including bridge VLAN filtering
support.
- Hardware offload support.
- Describe the [OFFLOAD] and [HW_OFFLOAD] tags in the conntrack table
listing.
- Replace 'flow offload' by 'flow add' in example rulesets (preferred
syntax).
- Describe existing cache limitations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading IPv4 routed flows, including SNAT/DNAT,
one VLAN, PPPoE and DSA.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPE (packet processing engine) is used to offload NAT/routed or even
bridged flows. This patch brings up the PPE and uses it to get a packet
hash. It also contains some functionality that will be used to bring up
flow offloading.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using DSA, set the special tag in GDM ingress control to allow the MAC
to parse packets properly earlier. This affects rx DMA source port reporting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa infrastructure provides a well-defined hierarchy of devices,
pass up the call to set up the flow block to the master device. From the
software dataplane, the netfilter infrastructure uses the dsa slave
devices to refer to the input and output device for the given skbuff.
Similarly, the flowtable definition in the ruleset refers to the dsa
slave port devices.
This patch adds the glue code to call ndo_setup_tc with TC_SETUP_FT
with the master device via the dsa slave devices.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PPPoE push action if layer 2 protocol is ETH_P_PPP_SES to add
PPPoE flowtable hardware offload support.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an action to represent the PPPoE hardware offload support that
includes the session ID.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch might have already added the VLAN tag through PVID hardware
offload. Keep this extra VLAN in the flowtable but skip it on egress.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a forward path to reach an ethernet device and hardware
offload is enabled, then use the direct xmit path.
Moreover, store the real device in the direct xmit path info since
software datapath uses dev_hard_header() to push the layer encapsulation
headers while hardware offload refers to the real device.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the flow tuple xmit_type is set to FLOW_OFFLOAD_XMIT_DIRECT, the
dst_cache pointer is not valid, and the h_source/h_dest/ifidx out fields
need to be used.
This patch also adds the FLOW_ACTION_VLAN_PUSH action to pass the VLAN
tag to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new tests to cover bridge and vlan support:
- Add a bridge device to the Router1 (nsr1) container and attach the
veth0 device to the bridge. Set the IP address to the bridge device
to exercise the bridge forwarding path.
- Add vlan encapsulation between to the bridge device in the Router1 and
one of the sender containers (ns1).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the master ethernet device by the dsa slave port. Packets coming
in from the software ingress path use the dsa slave port as input
device.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PPPoE protocol and session id to the flow tuple using the encap
fields to uniquely identify flows from the receive path. For the
transmit path, dev_hard_header() on the vlan device push the headers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the vlan tag based when PVID is set on.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the vlan id and protocol to the flow tuple to uniquely identify
flows from the receive path. For the transmit path, dev_hard_header() on
the vlan device push the headers. This patch includes support for two
vlan headers (QinQ) from the ingress path.
Add a generic encap field to the flowtable entry which stores the
protocol and the tag id. This allows to reuse these fields in the PPPoE
support coming in a later patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The egress device in the tuple is obtained from route. Use
dev_fill_forward_path() instead to provide the real egress device for
this flow whenever this is available.
The new FLOW_OFFLOAD_XMIT_DIRECT type uses dev_queue_xmit() to transmit
ethernet frames. Cache the source and destination hardware address to
use dev_queue_xmit() to transfer packets.
The FLOW_OFFLOAD_XMIT_DIRECT replaces FLOW_OFFLOAD_XMIT_NEIGH if
dev_fill_forward_path() finds a direct transmit path.
In case of topology updates, if peer is moved to different bridge port,
the connection will time out, reconnect will result in a new entry with
the correct path. Snooping fdb updates would allow for cleaning up stale
flowtable entries.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obtain the ingress device in the tuple from the route in the reply
direction. Use dev_fill_forward_path() instead to get the real ingress
device for this flow.
Fall back to use the ingress device that the IP forwarding route
provides if:
- dev_fill_forward_path() finds no real ingress device.
- the ingress device that is obtained is not part of the flowtable
devices.
- this route has a xfrm policy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the xmit_type field that defines the two supported xmit paths in the
flowtable data plane, which are the neighbour and the xfrm xmit paths.
This patch prepares for new flowtable xmit path types to come.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .ndo_fill_forward_path for dsa slave port devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass on the PPPoE session ID, destination hardware address and the real
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the VLAN settings of the bridge and the port, the bridge can
either add or remove a tag. When vlan filtering is enabled, the fdb lookup
also needs to know the VLAN tag/proto for the destination address
To provide this, keep track of the stack of VLAN tags for the path in the
lookup context
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .ndo_fill_forward_path for bridge devices.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .ndo_fill_forward_path for vlan devices.
For instance, assuming the following topology:
IP forwarding
/ \
eth0.100 eth0
|
eth0
.
.
.
ethX
ab💿ef🆎cd:ef
For packets going through IP forwarding to eth0.100 whose destination
MAC address is ab💿ef🆎cd:ef, dev_fill_forward_path() provides the
following path:
eth0.100 -> eth0
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dev_fill_forward_path() which resolves the path to reach
the real netdevice from the IP forwarding side. This function takes as
input the netdevice and the destination hardware address and it walks
down the devices calling .ndo_fill_forward_path() for each device until
the real device is found.
For instance, assuming the following topology:
IP forwarding
/ \
br0 eth0
/ \
eth1 eth2
.
.
.
ethX
ab💿ef🆎cd:ef
where eth1 and eth2 are bridge ports and eth0 provides WAN connectivity.
ethX is the interface in another box which is connected to the eth1
bridge port.
For packets going through IP forwarding to br0 whose destination MAC
address is ab💿ef🆎cd:ef, dev_fill_forward_path() provides the
following path:
br0 -> eth1
.ndo_fill_forward_path for br0 looks up at the FDB for the bridge port
from the destination MAC address to get the bridge port eth1.
This information allows to create a fast path that bypasses the classic
bridge and IP forwarding paths, so packets go directly from the bridge
port eth1 to eth0 (wan interface) and vice versa.
fast path
.------------------------.
/ \
| IP forwarding |
| / \ \/
| br0 eth0
. / \
-> eth1 eth2
.
.
.
ethX
ab💿ef🆎cd:ef
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to br_vlan_replay_one is returning an error return value but
this is not being assigned to err and the following check on err is
currently always false because err was initialized to zero. Fix this
by assigning err.
Addresses-Coverity: ("'Constant' variable guards dead code")
Fixes: 22f67cdfae ("net: bridge: add helper to replay VLANs installed on port")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
bridge: mrp: Disable roles before deleting
The first patch in this series make sures that the driver is notified
that the role is disabled before the MRP instance is deleted. The
second patch uses this so it can simplify the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver will always be notified that the role is deleted
before the ring is deleted, then we don't need to duplicate the logic of
cleaning the resources also in the delete function.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MRP instance was created, the driver was notified that the
instance is created and then in a different callback about role of the
instance. But when the instance was deleted the driver was notified only
that the MRP instance is deleted and not also that the role is disabled.
This patch make sure that the driver is notified that the role is
changed to disabled before the MRP instance is deleted to have similar
callbacks with the creating of the instance. In this way it would
simplify the logic in the drivers.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns: add some cleanups
This series includes some cleanups for the HNS ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some variables in HNS driver will not being referenced
before assigned, so there is no need to init them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The !! operation of variable en in hns_mac_config_sds_loopback_acpi()
is redundant, so remove it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS_LED_PC_REG is not used and can be removed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC_LB_TEST_RX_PKG_ERR is not used and can be removed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since config_half_duplex() in struct mac_driver is unused,
so remove it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
