To more closely match the IEGD ns2501 driver behaviour, call the
mode_set hook while the DVO port is still disabled, then enable the DVO
port, and finally call the dpms hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Fujitsu-Siememens S6010 the ns2501 chip is hooked up to DVOB instead
of DVOC.
FIXME: Maybe need to dig out the correct DVO port from VBT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable double wide even if the pipe quirk compels us to leave the
pipe running. Double wide has certain implications for the plane
assignments so best keep it off.
Also helps resuming from S3 on the Fujitsu-Siemens Lifebook S6010
when double wide was enabled prior to suspend.
We do leave the pixel clock ticking at the original rate which would
require double wide to be enabled. But since the planes are all disabled
I'm hoping that the overly fast clock won't cause any problems. Seems
to be fine so far.
v2: Disable double wide also when turning the pipe off
v3: Reorder wrt. force pipe B quirk
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just pass the intel_crtc around instead of dev_priv+pipe.
Also make intel_wait_for_pipe_off() static since it's only used in
intel_display.c.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen2/3 platforms have a boatload of rings we're not using. On my 830
the BIOS/hw can leave some of those "active" after resume which will
prevent c3 entry. The ring is apparently considered active whenever
head != tail even if the ring is disabled.
Disable and clear all such unused ringbuffers on init/resume.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My 830 is unhappy with trickle feed enabled. The symptom is that
the image on the screen shifts a bit to right occasionally.
The BIOS initially disables trickle feed, but it gets reset during
suspend, so we need to re-disable it ourselves. Juse disable it
always.
Also disable it for all other gen2/3 platforms since we disable it
for all more recent platforms as well (until HSW that is). At least
my 855 doesn't seem to mind us doing this. I don't have gen3
hardware to test that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The max watermark value for gen2 planes B and C is 0x1f, instead of
the 0x3f that plane A uses.
Also check against the max even if the pipe is disabled since the
FIFO size exceeds the plane B and C max watermark value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets us out of our init code and out to userspace quite a bit
faster, but does open us up to some bugs given the state of our init
time locking.
v2: switch to async_schedule (Chris)
check with lockdep, seems happy (Jesse)
move hotplug enable flag set to fbdev_initial_config (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebase on top of the dev_priv->enable_hotplug_processing
removal.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the BDW example and apply the workarounds touching registers
which are saved in the context image through LRIs in the new
ring->init_context() hook.
This makes Mesa much happier and eg. glxgears doesn't hang after
the first frame.
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add missing wa table initialization to avoid a functional
conflict with Arun's wa table debugfs support.]
Reviewed-by: "Barbalho, Rafael" <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At this point of the code the obj var is already NULL, so we don't
need to set it again to NULL.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV wants even rps opcodes so print a warning of the
min/max/rpe/rp1 values are odd, and warn if an odd value
slips through to valleyview_set_rps() and truncate it to
an even value.
Also add a comment to chv_freq_opcode() to make sure no one
changes the code without considering this requirement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Help git along in applying the patch, somehow it silently
ended up in the vlv init_gt_powersave function.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The batchbuffer that sets the render context state is submitted
in a different way, and from different places.
We needed to make both the render state preparation and free functions
outside accesible, and namespace accordingly. This mess is so that all
LR, LRC and Execlists functionality can go together in intel_lrc.c: we
can fix all of this later on, once the interfaces are clear.
v2: Create a separate ctx->rcs_initialized for the Execlists case, as
suggested by Chris Wilson.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
v3: Setup ring status page in lr_context_deferred_create when the
default context is being created. This means that the render state
init for the default context is no longer a special case. Execute
deferred creation of the default context at the end of
logical_ring_init to allow the render state commands to be submitted.
Fix style errors reported by checkpatch. Rebased.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW supports GT C0 residency reporting in constant time unit. Driver
calculates GT utilization based on C0 residency and adjusts RP
frequency up/down accordingly. For offscreen workload specificly,
set frequency to RP0.
Offscreen task is not restricted by frame rate, it can be
executed as soon as possible. Transcoding and serilized workload
between CPU and GPU both need high GT performance, RP0 is a good
option in this case. RC6 will kick in to compensate power
consumption when GT is not active.
v2: Rebase on recent drm-intel-nightly
v3: Add flip timerout monitor, when no flip is deteced within
100ms, set frequency to RP0.
Signed-off-by: Daisy Sun <daisy.sun@intel.com>
[torourke: rebased on latest and resolved conflict]
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
init_clock_gating() is too late to read out the mem_freq. We already
want to print out the GPU MHz numbers before it's called. Move the
mem_freq setup to init_gt_powersave().
v2: Also kill the CHV_CZ_CLOCK_FREQ_MODE_* defines
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the pixel_size we got from drm_format_plane_cpp() instead of
fb->bits_per_pixel/8 when computing the primary plane page/linear
offsets. Avoids a few divs and makes the code more future proof
against funky pixel formats where bits_per_pixel isn't well defined.
This is what we already did in the sprite code.
Note that the relevant sprite patch was
commit ca320ac456
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Dec 19 12:14:22 2012 +0000
drm/i915: Use pixel size for computing linear offsets into a sprite
This change was required on sprites because they support yuv formats
which have fb->bits_per_pixel undefined.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add Chris' software archeology as a note to the commit
message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During driver init we may not have a valid framebuffer for the primary
plane even though the plane is enabled due to failed BIOS fb takeover.
This means we have to avoid dereferencing the fb in
.update_primary_plane() when disabling the plane.
The introduction of the primary plane rotation in
commit d91a2cb8e5104233c02bbde539bd4ee455ec12ac
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Fri Aug 22 14:06:04 2014 +0530
drm/i915: Add 180 degree primary plane rotation support
caused a regression by trying to look up the pixel format before we can
be sure there's a valid fb available. This isn't entirely unsurprising
since the rotation patches originally predate the change to the primary
plane code that calls .update_primary_plane() also when disabling the
plane:
commit fdd508a641
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Aug 8 21:51:11 2014 +0300
drm/i915: Call .update_primary_plane in intel_{enable,
disable}_primary_hw_plane()
v2: Warn but don't blow up when trying to enable a plane w/o an fb (Chris)
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The workarounds that are applied are exported to a debugfs file;
this is used to verify their state after the test case (reset or
suspend/resume etc). This patch is only required to support i-g-t.
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For BDW workarounds are currently initialized in init_clock_gating() but
they are lost during reset, suspend/resume etc; this patch moves the WAs
that are part of register state context to render ring init fn otherwise
default context ends up with incorrect values as they don't get initialized
until init_clock_gating fn.
v2: Add workarounds to golden render state
This method has its own issues, first of all this is different for
each gen and it is generated using a tool so adding new workaround
and mainitaining them across gens is not a straightforward process.
v3: Use LRIs to emit these workarounds (Ville)
Instead of modifying the golden render state the same LRIs are
emitted from within the driver.
v4: Use abstract name when exporting gen specific routines (Chris)
For: VIZ-4092
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to spec FBC on BDW and HSW are identical without any gaps.
So let's copy the nuke and let FBC really start compressing stuff.
Without this patch we can verify with false color that nothing is being
compressed. With the nuke in place and false color it is possible
to see false color debugs.
Unfortunatelly on some rings like BCS on BDW we have to avoid Bits 22:18 on
LRIs due to a high risk of hung. So, when using Blt ring for frontbuffer rend
cache would never been cleaned and FBC would stop compressing buffer.
One alternative is to cache clean on software frontbuffer tracking.
v2: Fix rebase conflict.
v3: Do not clean cache on BCS ring. Instead use sw frontbuffer tracking.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to avoid confusion with ARRAY_SIZE()/2 and hdmi_level*2.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Resolve silent patch conflict (didn't even fail to build)
with with Sonika's preceding patch to use the
hsw_ddi_translations_fdi table to driver the fdi link training
iteration loop. Also drop the double-write loop Damien spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Renaming the HSW-specific macros for ddi buffer translation slot to denote the
slot and not the vswing/pre-emph values as they are platform-dependent.
This patch is based on top of the patch series for renaming the DP training
vswing/pre-emph defines:
http://lists.freedesktop.org/archives/intel-gfx/2014-August/050407.html
v2: Creating single macro with argument for slot number (Damien)
v3: Adding macro for num of translation entries (Damien)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, it was possible for the GPU memory accesses to be swizzled
to try to optimize the fetches for tiled buffers. This swizzling was on
top of what the memory controller in the uncore already does.
With broadwell, we drop that GPU side swizzling, and the corresponding
initialization in 3 units (GAM, GT, DE). All those bits are reserved, as
specs put it:
Before Gen8, there was a historical configuration control field to
swizzle address bit[6] for in X/Y tiling modes. This was set in three
different places: TILECTL[1:0], ARB_MODE[5:4], and
DISP_ARB_CTL[14:13]"
For Gen8 the swizzle fields are all reserved, and the CPU's memory
controller performs all address swizzling modifications.
This also means that user space doesn't have to manually swizzle when
accessing tiled buffers from the CPU, and so we always return
I915_BIT_6_SWIZZLE_NONE from i915_gem_detect_bit_6_swizzle(), which
short-circuits the initialization of the registers mentionned above in
i915_gem_init_swizzling().
v2: Refine the explanation a bit more (Daniel)
v3: Make it BDW+ specific (Steve)
Cc: Steve Aarnio <steve.j.aarnio@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Keep the actual code to set the tiling bits for now, in case
some bios escaped to the wild that uses this - we'd need it for
fastboot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of going through hoops, just put the driver author directly as
DRM_AUTHOR() argument. This will also make it consistent when we add
Intel to the list.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix assert_panel_unlocked for vlv/chv, and improve it a bit for
non-LVDS. Also don't pretend it works for DDI. There's still work to do
to get this right for eDP on PCH platforms, but this is a start.
v2: WARN_ON(HAS_DDI)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch introduces fixes for the debugfs attributes emitted by
the i915 driver for GEN8. Currently, it is not emitting the correct
attributes which include the status of RC6 states.
Change-Id: Ib2068a0cac9a5wq3f228e547fa1a097ad369d242df
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than describing an object as either "snooped or LLC", we can do
better as we should know what machine we are running on!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BDW we're seeing a problem that after we runtime resume, the
outputs connected to DDI C are not detected: they don't appear in the
SDEISR register and GMBUS transactions don't work. They stop working
at the moment we call intel_opregion_notify_adapter() during runtime
suspend, but they don't go back to work when we call the same function
during runtime resume. They only work after we do a modeset and call
intel_opregion_notify_encoder(), but this point is already too late.
While debugging, I tried to pass PCI_D3hot which is the value that
matches the spec, and it seems to have solved the problem. I couldn't
find any explanation of why this solves the problem, but there's also
no documented explanation - besides our code and git log - of why
Haswell should use PCI_D1, so keep this for now in order to keep BDW
runtime PM working.
Also add a comment to point the fact that there's no spec documenting
all the weirdness involved here.
Cc: kristen.c.accardi@intel.com
Testcase: igt/pm_rpm/drm-resources-equal
Testcase: igt/pm_rpm/i2c
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because CHV uses cherryview_init_clock_gating instead of
gen8_init_clock_gating.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because BDW has WPT, which is equivalent to LPT. This is just like the
CPT/PPT case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the correct mask for the unlock bits. In theory this could have lead
to incorrect asserts but this is unlikely in practise.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two functions make no sense in an Logical Ring Context & Execlists
world.
v2: We got rid of lrc_enabled and centralized everything in the sanitized
i915.enable_execlists instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
v3: Rebased. Corrected a typo in comment for i915_switch_context and
added a comment that it should not be called in execlist mode. Added
WARN_ON if i915_switch_context is called in execlist mode. Moved check
for execlist mode out of i915_switch_context and into callers. Added
comment in context_reset explaining why nothing is done in execlist
mode.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Simplify the patch subject so I can understand it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Programing GT IER interrupts was fumbled while enabling Interrupts for
gen8
We forgot to program PM IER interrupt in gen8_gt_irq_postinstall based
on the new re-worked interrupt routines.
v2: Kill the loop and init GT interrupts individually (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Adjust commit message as per discussion with Deepak.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A pending commit removes synchronous mode from switch_mm. This breaks
execlists because switch_mm will always try to write to the legacy ring
buffer.
Return immediately from i915_ppgtt_init_gw in execlists mode.
No longer check for execlists mode in gen8_ppgtt_enable() because this
will no longer be called in execlists mode.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be sure to always flush a stuck pageflip even if we couldn't possibly
expect one to be there.
References: https://bugs.freedesktop.org/show_bug.cgi?id=82612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately, the gem_obj/vma relationship is not symmetrical; a gem_obj
can look up for the same vma more than once (where the ppgtt refcount is
incremented), but will free the vma only once (i915_gem_free_object).
This difference in refcount get/put means that the ppgtt is not removed
after the context and vma are destroyed, because sometimes the refcount
will never go back to zero.
v2: Just move the ppgtt refcount into vma_create.
OTC-Jira: VIZ-3719
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Less pointless indentation is always nice. There will be a bit more
code in this function once the power sequencer locking is fixed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we force vdd off warn if someone is still using it. With this
change the delayed vdd off work needs to check want_panel_vdd
itself to make sure it doesn't try to turn vdd off when someone
is using it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks nicer.
Not functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "No functional change" as requested by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a comment to explain why we care about the current want_panel_vdd
state in intel_dp_aux_ch().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
edp_* are now the lower level functions and intel_edp_* the higher level
ones. One should use them in pairs.
v2: Don't return void (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the higher level vdd on func here. Not a big deal
yet (we'd just get the warn when things go awry) but when the
locking gets fixed this becomes more important.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the port as a parameter to PANEL_PORT_SELECT_VLV results in
neater code. Sadly the PCH port select bits aren't suitable for the
same treatment and the resulting macro would be much uglier, so
leave those defines as is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous commit broke aliasing PPGTT for lrc, resulting in a kernel oops
on boot. Add a check so that is full PPGTT is not in use the context is
populated with the aliasing PPGTT.
Issue: VIZ-4278
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the move over to use BIOS connector configs, we lost the ability to
force a specific set of connectors on or off. Try to remedy that by
dropping back to the old behavior if we detect a hard coded connector
config that tries to enable a connector (disabling is easy!).
Based on earlier patches by Jesse Barnes.
v2: Remove Jesse's patch
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need do forcewake before Disabling RC6, This is what the BIOS
expects while going into suspend.
v2: updated commit message. (Daniel)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improve the debug message that tells us we've been waiting for a vblank
that never arrived. Printing the pipe could lead a "doh!" moment where
we've been waiting for a vblank on a pipe that was off for instance.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Polish commit message a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
