[ Upstream commit f575957882 ]
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5c54a9d3 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61 ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aef4ed59 ]
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805c74eac8 upstream.
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cc3542c76 upstream.
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b34556 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block")
Cc: stable@kernel.org
Co-developed-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d656bd259 ]
While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.
gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a), so add protection for that.
Fixes: bdbbae241a ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95dd1e34ff ]
If gpio_set_transitory() fails, we should free the GPIO again. Most
notably, the flag FLAG_REQUESTED has previously been set in
gpiod_request_commit(), and should be reset on failure.
To my knowledge, this does not affect any current users, since the
gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted
to 0. However the gpio_set_transitory() function calles the .set_config()
function of the corresponding GPIO chip and there are some GPIO drivers in
which some (unlikely) branches return other values like -EPROBE_DEFER,
and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not
be reset, which results in the pin being blocked until the next reboot.
Fixes: e10f72bf4b ("gpio: gpiolib: Generalise state persistence beyond sleep")
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4302326197 ]
Add flag IRQCHIP_MASK_ON_SUSPEND to make sure gpio irq is masked on
suspend, if lack this flag, current irq arctitecture will not mask
the irq, and these unmasked gpio irq will wrongly wakeup the system
even they are not config as wakeup source.
Also add flag IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND to make sure the gpio
irq which is configed as wakeup source can work as expect.
Fixes: 7f2691a196 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6ef4f8ede ]
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 4302326197 ("gpio: vf610: mask the gpio irq in system suspend and support wakeup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc363413ef upstream.
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Fixes: 659d8a6231 ("gpio: vf610: add imx7ulp support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e8bc2dda5 ]
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
timbgpio_gpio_set()
--> timbgpio_update_bit()
--> spin_lock(&tgpio->lock)
<interrupt>
--> timbgpio_irq_disable()
--> spin_lock_irqsave(&tgpio->lock)
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f057511650 upstream.
Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9315f17bf upstream.
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
Fixes: 5ae4cb94b3 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26d9e5640d ]
The drivers uses a mutex and I2C bus access in its PMIC EIC chip
get implementation. This means these functions can sleep and the PMIC EIC
chip should set the can_sleep property to true.
This will ensure that a warning is printed when trying to get the
value from a context that potentially can't sleep.
Fixes: 348f3cde84 ("gpio: Add Spreadtrum PMIC EIC driver support")
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b547b5e52a ]
If an error occurs after a successful irq_domain_add_linear() call, it
should be undone by a corresponding irq_domain_remove(), as already done
in the remove function.
Fixes: c6ce2b6bff ("gpio: add TB10x GPIO driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e39c1ac68 ]
Associate the swnode of the GPIO device's (which is the interrupt
controller here) with the irq domain. Otherwise the interrupt-controller
device attribute is a no-op.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab4109f91b ]
If a GPIO simulator device is unbound with interrupts still requested,
we will hit a use-after-free issue in __irq_domain_deactivate_irq(). The
owner of the irq domain must dispose of all mappings before destroying
the domain object.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5a78d5db9c upstream.
Simulated chips use a mutex for synchronization in driver callbacks so
they must not be called from interrupt context. Set the can_sleep field
of the GPIO chip to true to force users to only use threaded irqs.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f83d13de upstream.
The WinSystems WS16C48 I/O address region spans offsets 0x0 through 0xA,
which is a total of 11 bytes. Fix the WS16C48_EXTENT define to the
correct value of 11 so that access to necessary device registers is
properly requested in the ws16c48_probe() callback by the
devm_request_region() function call.
Fixes: 2c05a0f29f ("gpio: ws16c48: Implement and utilize register structures")
Cc: stable@vger.kernel.org
Cc: Paul Demetrotion <pdemetrotion@winsystems.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 644ee70267 ]
Uwe Kleine-König pointed out we still have one resource leak in the mvebu
driver triggered on driver detach. Let's address it with a custom devm
action.
Fixes: 812d47889a ("gpio/mvebu: Use irq_domain_add_linear")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1945063eb5 ]
This allows to get rid of a call to pwmchip_remove() in the error path. There
is no .remove function for this driver, so this change fixes a resource leak
when a gpio-mvebu device is unbound.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7adc6c10 ]
Make tps68470_gpio_output() call tps68470_gpio_set() for output-only pins
too, so that the initial value passed to gpiod_direction_output() is
honored for these pins too.
Fixes: 275b13a655 ("gpio: Add support for TPS68470 GPIOs")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff7a1790fb ]
Up until commit 6a45b0e258 ("gpiolib: Introduce
gpiochip_irqchip_add_domain()") all irq_domains were allocated
by gpiolib itself and thus gpiolib also takes care of freeing it.
With gpiochip_irqchip_add_domain() a user of gpiolib can associate an
irq_domain with the gpio_chip. This irq_domain is not managed by
gpiolib and therefore must not be freed by gpiolib.
Fixes: 6a45b0e258 ("gpiolib: Introduce gpiochip_irqchip_add_domain()")
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bcb976d8 ]
Add the missing check for platform_get_irq() and return error code
if it fails.
The returned error code will be dealed with in
builtin_platform_driver(sifive_gpio_driver) and the driver will not
be registered.
Fixes: f52d6d8b43 ("gpio: sifive: To get gpio irq offset from device tree data")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c00914e54 ]
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1f ("gpio: Restrict usage of GPIO chip irq members before initialization")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ae9979bf ]
When constructing the sim, gpio-sim constructs an array of named lines,
sized based on the largest offset of any named line, and then initializes
that array with the names of all lines, including unnamed hogs with higher
offsets. In doing so it writes NULLs beyond the extent of the array.
Add a check that only named lines are used to initialize the array.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Kent Gibson<warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3002b8642f ]
In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.
The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.
Fixes: d0918a84af ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116")
Reported-by: Xing Tong Wu <xingtong.wu@siemens.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a1bb16e0f upstream.
This driver's debugfs files have had a read operation since commit
2a9e27408e ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782eea0c89 upstream.
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xNU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
This patch is analoge to a very similar patch for NL5xRU, just the DMI
string changed.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b75c47036 ]
Add the IRQCHIP_SKIP_SET_WAKE flag since there are no special IRQ Wake
bits that can be set to enable wakeup IRQ.
Fixes: 3d9edf09d4 ("[ARM] 4457/2: davinci: GPIO support")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe092498cb ]
The interrupt enable bits might be set if we want to use the GPIO as
wakeup source. Clearing this will mean disabling of interrupts in the GPIO
banks that we may want to wakeup from.
Thus remove the line that was clearing this bit from the driver's save
context function.
Cc: Devarsh Thakkar <devarsht@ti.com>
Fixes: 0651a73092 ("gpio: davinci: Add support for system suspend/resume PM")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c452cff79 ]
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 6f57937980 ("pwm: hibvt: Explicitly set .polarity in .get_state()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49765b5f4 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e ("gpio: add a reusable generic gpio_chip using regmap")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: linux-gpio@vger.kernel.org
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f8ecb7f85 ]
Current GPIO label is fixed, so can't distinguish different GPIO
controllers through labels. Use dev name instead.
Fixes: 7f2691a196 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d63f11c02b ]
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
adjusted the policy to enable wakeup by default if the ACPI tables
indicated that a device was wake capable.
It was reported however that this broke suspend on at least two System76
systems in S3 mode and two Lenovo Gen2a systems, but only with S3.
When the machines are set to s2idle, wakeup behaves properly.
Configuring the GPIOs for wakeup with S3 doesn't work properly, so only
set it when the system supports low power idle.
Fixes: 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Fixes: b38f2d5d96 ("i2c: acpi: Use ACPI wake capability bit to set wake_irq")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2357
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2162013
Reported-by: Nathan Smythe <ncsmythe@scruboak.org>
Tested-by: Nathan Smythe <ncsmythe@scruboak.org>
Suggested-by: Raul Rangel <rrangel@chromium.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cb786180d ]
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xRU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
Fixes: 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Reported-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627
Co-developed-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e3b175f07 ]
Using the `ignore_wake` quirk or module parameter doesn't work for any pin
that has been specified in the _CRS instead of _AEI.
Extend the `acpi_gpio_irq_is_wake` check to cover both places.
Suggested-by: Raul Rangel <rrangel@chromium.org>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1722335
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f04cdbdb2 ]
Fix wrong translation of irq numbers in port F handler, as ep93xx hwirqs
increased by 1, we should simply decrease them by 1 in translation.
Fixes: 482c27273f ("ARM: ep93xx: renumber interrupts")
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3787035861 ]
We recently added locking to this function but one error path was
over looked. Drop the lock before returning.
Fixes: e546427762 ("gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e88a0feeb ]
Always configure GPIO pins which are used as interrupt source as INPUTs.
In case the default pin configuration is OUTPUT, or the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT and no interrupts are received.
Always configure the interrupt source GPIO pin as input to fix the above case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 07bd1a6cc7 ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e546427762 ]
The driver currently performs register read-modify-write without locking
in its irqchip part, this could lead to a race condition when configuring
interrupt mode setting. Add the missing bgpio spinlock lock/unlock around
the register read-modify-write.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Fixes: 07bd1a6cc7 ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 694175cd8a ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90fee3dd5b ]
There is a variable pinctrl declared without initializer. And then
has the case (switch operation chose the default case) to directly
use this uninitialized value, this is not a safe behavior. So here
initialize the pinctrl as 0 to avoid this issue.
This is reported by Coverity.
Fixes: 13c5d4ce80 ("gpio: pca953x: Add support for PCAL6534")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdbbae241a ]
While any of the GPIO cdev syscalls is in progress, the kernel can call
gpiochip_remove() (for instance, when a USB GPIO expander is disconnected)
which will set gdev->chip to NULL after which any subsequent access will
cause a crash.
To avoid that: use an RW-semaphore in which the syscalls take it for
reading (so that we don't needlessly prohibit the user-space from calling
syscalls simultaneously) while gpiochip_remove() takes it for writing so
that it can only happen once all syscalls return.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[Nick: fixed a build failure with CDEV_V1 disabled]
Co-authored-by: Nick Hainke <vincent@systemli.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533aae7c94 ]
There are several places where we can crash the kernel by requesting
lines, unbinding the GPIO device, then calling any of the system calls
relevant to the GPIO character device's annonymous file descriptors:
ioctl(), read(), poll().
While I observed it with the GPIO simulator, it will also happen for any
of the GPIO devices that can be hot-unplugged - for instance any HID GPIO
expander (e.g. CP2112).
This affects both v1 and v2 uAPI.
This fixes it partially by checking if gdev->chip is not NULL but it
doesn't entirely remedy the situation as we still have a race condition
in which another thread can remove the device after the check.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de04 ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
