We were just continuing in this case, surely not desired.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analogously to prueth_remove, just also taking care for NULL'ing the
iep pointers.
Fixes: 186734c158 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Fixes: 443a2367ba ("net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently icss_iep_set_counter() writes the upper 32-bits of the
counter value to both the lower and upper counter registers, so
fix this by writing the appropriate value to the lower register.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Link: https://lore.kernel.org/r/20231107120037.1513546-1-diogo.ivo@siemens.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rx_pause flag says that whether we support receiving Pause frames.
When a Pause frame is received TX is delayed for some time. This is TX
flow control. In the same manner tx_pause is actually RX flow control.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a device tree entry called "local-mac-address"
which can be filled by the bootloader or manually set.This is
useful when the user does not want to use the MAC address
programmed into the SoC.
Currently, the davinci_emac reads the MAC from the DT, copies
it from pdata->mac_addr to priv->mac_addr, then blindly overwrites
it by reading from registers in the SoC, and falls back to a
random MAC if it's still not valid. This completely ignores any
MAC address in the device tree.
In order to use the local-mac-address, check to see if the contents
of priv->mac_addr are valid before falling back to reading from the
SoC when the MAC address is not valid.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231022151911.4279-1-aford173@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The bitmasks for EMAC_PORT_DISABLE and EMAC_PORT_FORWARD r30 commands are
wrong in the driver.
Update the bitmasks of these commands to the correct ones as used by the
ICSSG firmware. These bitmasks are backwards compatible and work with
any ICSSG firmware version.
Fixes: e9b4ece7d7 ("net: ti: icssg-prueth: Add Firmware config and classification APIs.")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231018150715.3085380-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With CONFIG_TI_K3_AM65_CPSW_NUSS=y and CONFIG_TI_ICSSG_PRUETH=m,
k3-cppi-desc-pool.o is linked to a module and also to vmlinux even though
the expected CFLAGS are different between builtins and modules.
The build system is complaining about the following:
k3-cppi-desc-pool.o is added to multiple modules: icssg-prueth
ti-am65-cpsw-nuss
Introduce the new module, k3-cppi-desc-pool, to provide the common
functions to ti-am65-cpsw-nuss and icssg-prueth.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231018064936.3146846-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Other implementations of .*get_drvinfo also use strscpy so this patch
brings keystone_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-ethernet-ti-netcp_ethss-c-v1-1-93142e620864@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ICSSG HW stats on TX side considers 8 preamble bytes as data bytes. Due
to this the tx_bytes of ICSSG interface doesn't match the rx_bytes of the
link partner. There is no public errata available yet.
As a workaround to fix this, decrease tx_bytes by 8 bytes for every tx
frame.
Fixes: c1e10d5dc7 ("net: ti: icssg-prueth: Add ICSSG Stats")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231012064626.977466-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR7 is going to be removed from the Kernel, so remove its networking
support in form of the cpmac driver. This allows us to remove the
platform because this driver includes a platform specific header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/all/20230922061530.3121-6-wsa+renesas@sang-engineering.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_do_flush_map() is deprecated and new code should use xdp_do_flush()
instead.
Replace xdp_do_flush_map() with xdp_do_flush().
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: John Crispin <john@phrozen.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Cc: Shenwei Wang <shenwei.wang@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> # cpmac
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.
Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can now use PTP if enabled but fails to link built-in
if PTP is a loadable module:
aarch64-linux-ld: drivers/net/ethernet/ti/icssg/icss_iep.o: in function `icss_iep_get_ptp_clock_idx':
icss_iep.c:(.text+0x200): undefined reference to `ptp_clock_index'
Add the usual dependency to avoid this.
Fixes: 186734c158 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add AM64x ICSSG support which is similar to am65x SR2.0, but required:
- all ring configured in exposed ring mode
- always fill both original and buffer fields in cppi5 desc
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For AM65x SR2.0 it's required to enable IEP1 in raw 64bit mode which is
used by PRU FW to monitor the link and apply w/a for 10M link issue.
Note. No public errata available yet.
Without this w/a the PRU FW will stuck if link state changes under TX
traffic pressure.
Hence, add support for 10M full duplex for AM65x SR2.0:
- add new IEP API to enable IEP, but without PTP support
- add pdata quirk_10m_link_issue to enable 10M link issue w/a.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet timestamping TS and PTP PHC clock support.
For AM65x and AM64x:
- IEP1 is not used
- IEP0 is configured in shadow mode with 1ms cycle and shared between
Linux and FW. It provides time and TS in number cycles, so special
conversation in ns is required.
- IEP0 shared between PRUeth ports.
- IEP0 supports PPS, periodic output.
- IEP0 settime() and enabling PPS required FW interraction.
- RX TS provided with each packet in CPPI5 descriptor.
- TX TS returned through separate ICSSG hw queues for each port. TX TS
readiness is signaled by INTC IRQ. Only one packet at time can be requested
for TX TS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for Industrial Ethernet Peripheral (IEP) block of PRUSS to
support timestamping of ethernet packets and thus support PTP and PPS
for PRU ethernet ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MQPRIO Qdisc offload in full 'channel' mode which allows
not only setting up pri:tc mapping, but also configuring TX shapers on
external port FIFOs. The K3 CPSW MQPRIO Qdisc offload is expected to work
with VLAN/priority tagged packets. Non-tagged packets have to be mapped
only to TC0.
- TX traffic classes must be rated starting from TC that has highest
priority and with no gaps
- Traffic classes are used starting from 0, that has highest priority
- min_rate defines Committed Information Rate (guaranteed)
- max_rate defines Excess Information Rate (non guaranteed) and offloaded
as (max_rate[i] - tcX_min_rate[i])
- VLAN/priority tagged packets mapped to TC0 will exit switch with VLAN tag
priority 0
The configuration example:
ethtool -L eth1 tx 5
ethtool --set-priv-flags eth1 p0-rx-ptype-rrobin off
tc qdisc add dev eth1 parent root handle 100: mqprio num_tc 3 \
map 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 hw 1 mode channel \
shaper bw_rlimit min_rate 0 100mbit 200mbit max_rate 0 101mbit 202mbit
tc qdisc replace dev eth2 handle 100: parent root mqprio num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@0 hw 1
ip link add link eth1 name eth1.100 type vlan id 100
ip link set eth1.100 type vlan egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
In the above example two ports share the same TX CPPI queue 0 for low
priority traffic. 3 traffic classes are defined for eth1 and mapped to:
TC0 - low priority, TX CPPI queue 0 -> ext Port 1 fifo0, no rate limit
TC1 - prio 2, TX CPPI queue 1 -> ext Port 1 fifo1, CIR=100Mbit/s, EIR=1Mbit/s
TC2 - prio 3, TX CPPI queue 2 -> ext Port 1 fifo2, CIR=200Mbit/s, EIR=2Mbit/s
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split types and pure function declarations from page_pool.h
and add them in page_page/types.h, so that C sources can
include page_pool.h and headers should generally only include
page_pool/types.h as suggested by jakub.
Rename page_pool.h to page_pool/helpers.h to have both in
one place.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230804180529.2483231-2-aleksander.lobakin@intel.com
[Jakub: change microsoft/mana, fix kdoc paths in Documentation]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRdM/uy1Ege0+EN1fNar9k/UBDW4wUCZMvevwAKCRBar9k/UBDW
42Z0AP90hLZ9OmoghYAlALHLl8zqXuHCV8OeFXR5auqG+kkcCwEAx6h99vnh4zgP
Tngj6Yid60o39/IZXXblhV37HfSiyQ8=
=/kVE
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Add suspend / resume APIs to support power management in ICSSG ethernet
driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_stats.c to help dump, icssg related driver statistics.
ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.
These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.
This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like implementation of
custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
Every ICSSG core has two Programmable Real-Time Unit(PRUs),
two auxiliary Real-Time Transfer Unit (RT_PRUs), and
two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs
its own firmware. Every ICSSG core has two MII ports connect to these
PRUs and also a MDIO port.
The cores can run different firmwares to support different protocols and
features like switch-dev, timestamping, etc.
It uses System DMA to transfer and receive packets and
shared memory register emulation between the firmware and
driver for control and configuration.
This patch adds support for basic EMAC functionality with 1Gbps
and 100Mbps link speed. 10M and half duplex mode are not supported
currently as they require IEP, the support for which will be added later.
Support for switch-dev, timestamp, etc. will be added later
by subsequent patch series.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. These will be used by
ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MII helper APIs and MACROs. These APIs and MACROs will be later used
by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has
definition of prueth related structures.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As 32bits of dissector->used_keys are exhausted,
increase the size to 64bits.
This is base change for ESP/AH flow dissector patch.
Please find patch and discussions at
https://lore.kernel.org/netdev/ZMDNjD46BvZ5zp5I@corigine.com/T/#t
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Tested-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the
field will be strictly contained within one word. However, this is not
guaranteed to be the case and it is possible for ALE field entries to span
across up to two words at the most.
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: db82173f23 ("netdev: driver: ethernet: add cpsw address lookup engine support")
Signed-off-by: Tanmay Patil <t-patil@ti.com>
[s-vadapalli@ti.com: rephrased commit message and added Fixes tag]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code returns directly but it should instead call of_node_put()
to drop some reference counts.
Fixes: dab2b265dd ("net: ethernet: ti: am65-cpsw: Add support for SERDES configuration")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/e3012f0c-1621-40e6-bf7d-03c276f6e07f@kili.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPSW uses of_platform_* functions which are declared in of_platform.h.
of_platform.h gets implicitly included by of_device.h, but that is going
to be removed soon. Nothing else depends on of_device.h so it can be
dropped. of_platform.h also implicitly includes platform_device.h, so
add an explicit include for it, too.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's J784S4 SoC supports USXGMII mode. Add USXGMII mode to the
extra_modes member of the J784S4 SoC data.
Configure MAC control register for supporting USXGMII mode and add
MAC_5000FD in the "mac_capabilities" member of struct "phylink_config".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
