This series adds a driver for interconnects on MSM8996. This fixes some rare display underflows
and provides a slight heat reduction.
* icc-msm8996
dt-bindings: interconnect: Combine SDM660 bindings into RPM schema
interconnect: icc-rpm: Add support for bus power domain
dt-bindings: interconnect: Add Qualcomm MSM8996 DT bindings
interconnect: qcom: Add MSM8996 interconnect provider driver
Link: https://lore.kernel.org/r/20211021132329.234942-1-y.oudjana@protonmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Using icc-rpm on ARM32 currently results in clk_set_rate() errors during
boot, e.g. "bus clk_set_rate error: -22". This is very similar to commit
7381e27b1e ("interconnect: qcom: msm8974: Prevent integer overflow in rate")
where the u64 is converted to a signed long during clock rate rounding,
resulting in an overflow on 32-bit platforms.
Let's fix it similarly by making sure that the rate does not exceed
LONG_MAX. Such high clock rates will surely result in the maximum
frequency of the bus anyway.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211206114542.45325-1-stephan@gerhold.net
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
[georgi: remove icc_sync_state for platforms with incomplete support]
Link: https://lore.kernel.org/r/20211125174751.25317-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add a driver for the MSM8996 NoCs. This chip is similar to SDM660 where
some busses are controlled by RPM, while others directly by the AP with
writes to QoS registers.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20211021132329.234942-5-y.oudjana@protonmail.com
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add support for attaching to a power domain. This is required
for Aggregate 0 NoC on MSM8996, which is powered by a GDSC.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Link: https://lore.kernel.org/r/20211021132329.234942-3-y.oudjana@protonmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This patch series merges support for AP-owned and bus QoS from SDM660
into common code (icc-rpm.c). MSM8916 and MSM8939 support code is
extended to support these features. As I was touching these drivers, per
Bjorn's suggestion expand DEFINE_QNODE macros (which makes adding
QoS support much easier to review).
* icc-rpm
interconnect: icc-rpm: move bus clocks handling into qnoc_probe
interconnect: sdm660: expand DEFINE_QNODE macros
interconnect: sdm660: drop default/unused values
interconnect: sdm660: merge common code into icc-rpm
interconnect: icc-rpm: add support for QoS reg offset
interconnect: msm8916: expand DEFINE_QNODE macros
interconnect: msm8916: add support for AP-owned nodes
interconnect: msm8939: expand DEFINE_QNODE macros
interconnect: msm8939: add support for AP-owned nodes
interconnect: qcs404: expand DEFINE_QNODE macros
interconnect: qcom: drop DEFINE_QNODE macro
Link: https://lore.kernel.org/r/20210903232421.1384199-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Drop DEFINE_QNODE macro which has become unused.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-12-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
To follow the example of the rest of icc-rpm.h drivers, expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-11-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Port support for AP-owned nodes from the downstream device tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-10-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation to adding AP-owned nodes support to msm8939 expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-9-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Port support for AP-owned nodes from the downstream device tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-8-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In preparation to adding AP-owned nodes support to msm8916 expand
DEFINE_QNODE macros in the driver.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-7-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
SDM660 driver expects to have QoS registers at the beginning of NoC
address space (sdm660 platform shifts NoC base address). Add support for
using QoS register offset, so that other platforms do not have to change
existing device trees.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-6-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Other RPM interconnect drivers might also use QoS support. Move AP-owned
nodes support from SDM660 driver to common icc-rpm.c.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-5-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Expand DEFINE_QNODE macros, which with an addition of QoS become an ugly
beast with tons of different arguments. While we are at it also move
links lists to separate arrays.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-3-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
All icc-rpm drivers use the same set of bus clocks. Move handling of bus
clocks to qnoc_probe. This both simplifies the code and allows using
qnoc_probe as device's probe function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210903232421.1384199-2-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Here are changes for the 5.15-rc1 merge window consisting of interconnect
core and driver updates.
Framework change:
- Add sanity check to detect if node is already added to provider.
Driver changes:
- RPMh drivers probe function consolidation
- Add driver for SC8180x platforms
- Add support for SC8180x OSM L3
- Use driver-specific naming in OSM L3
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=K/bk
-----END PGP SIGNATURE-----
Merge tag 'icc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.15
Here are changes for the 5.15-rc1 merge window consisting of interconnect
core and driver updates.
Framework change:
- Add sanity check to detect if node is already added to provider.
Driver changes:
- RPMh drivers probe function consolidation
- Add driver for SC8180x platforms
- Add support for SC8180x OSM L3
- Use driver-specific naming in OSM L3
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: osm-l3: Use driver-specific naming
interconnect: qcom: osm-l3: Add sc8180x support
dt-bindings: interconnect: Add SC8180x to OSM L3 DT binding
interconnect: qcom: Add SC8180x providers
dt-bindings: interconnect: Add Qualcomm SC8180x DT bindings
interconnect: Sanity check that node isn't already on list
interconnect: qcom: icc-rpmh: Consolidate probe functions
This reverts commit f84f5b6f72, which is
causing regressions on some platforms, preventing them to boot or do a
clean reboot. This is because the above commit is sending also all the
zero bandwidth requests to turn off any resources that might be enabled
unnecessarily, but currently this may turn off interconnects that are
enabled by default, but with no consumer to keep them on.
Let's revert this for now as some platforms are not ready for such
change yet. In the future we can introduce some _ignore_unused option
that could keep also the unused resources on platforms that have only
partial interconnect support and also add .shutdown callbacks to deal
with disabling the resources in the right order.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/CAE-0n52iVgX0JjjnYi=NDg49xP961p=+W5R2bmO+2xwRceFhfA@mail.gmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
In situations were the developer screws up by e.g. not giving the OSM
nodes unique identifiers the interconnect framework might mix up nodes
between the OSM L3 provider and e.g. the RPMh provider.
The resulting callstack contains "qcom_icc_set", which is not unique to
the OSM L3 provider driver. Once the faulting qcom_icc_set() is
identified it's further confusing that "qcom_icc_node" is different
between the different drivers.
To avoid this confusion, rename the node struct and the setter in the
OSM L3 driver to include "osm_l3" in their names.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210725031414.3961227-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The SC8180x contains the usual RPMH based interconnect providers, add a
driver which defines the various busses and ports.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210723194243.3675795-2-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The expression sizeof(**ptr) for the void **ptr is just 1 rather than
the size of a pointer. Fix this by using sizeof(*ptr).
Addresses-Coverity: ("Wrong sizeof argument")
Fixes: e145d9a184 ("interconnect: Add devm_of_icc_get() as exported API for users")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730075408.19945-1-colin.king@canonical.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-5-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b59 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable]
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The pre_aggregate callback isn't called in all cases before calling
aggregate. Add the missing calls so providers can rely on consistent
framework behavior.
Fixes: d3703b3e25 ("interconnect: Aggregate before setting initial bandwidth")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-3-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The initial BW values may be used by providers to enforce floors. Zero
these values after sync-state so that providers know when to stop
enforcing them.
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-2-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Broken interconnect providers might add the same node multiple times or
in multiple providers, which causes strange errors as the provider's
node list is later traversed.
Detect that a node already has an associated provider, complain and
reject the addition of the node, to aid the developer.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210625234903.1324755-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current probe/remove functions are implemented separately for each
target, but they are almost identical. Replace them with common
functions that can be used across all rpmh targets.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210621214241.13521-1-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Here are changes for the 5.14-rc1 merge window consisting of interconnect
driver updates.
Driver changes:
- New driver for SC7280 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ihE7
-----END PGP SIGNATURE-----
Merge tag 'icc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.14
Here are changes for the 5.14-rc1 merge window consisting of interconnect
driver updates.
Driver changes:
- New driver for SC7280 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: Add SC7280 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SC7280 DT bindings
Add driver for the Qualcomm interconnect buses found in SC7280 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-3-git-send-email-okukatla@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620704673-104205-1-git-send-email-zou_wei@huawei.com
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)
-----BEGIN PGP SIGNATURE-----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=wU6U
-----END PGP SIGNATURE-----
Merge tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
These are the interconnect changes for the 5.13-rc1 merge window
with the highlights being drivers for two new platforms.
Driver changes:
- New driver for SM8350 platforms.
- New driver for SDM660 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=SguC
-----END PGP SIGNATURE-----
Merge tag 'icc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.13
These are the interconnect changes for the 5.13-rc1 merge window
with the highlights being drivers for two new platforms.
Driver changes:
- New driver for SM8350 platforms.
- New driver for SDM660 platforms.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sm8350: Add missing link between nodes
interconnect: qcom: sm8350: Use the correct ids
interconnect: qcom: sdm660: Fix kerneldoc warning
MAINTAINERS: icc: add interconnect tree
interconnect: qcom: Add SM8350 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SM8350 DT bindings
interconnect: qcom: icc-rpm: record slave RPM id in error log
interconnect: qcom: Add SDM660 interconnect provider driver
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
This patch series adds the SDM660 interconnect provider driver in
order to stop some timeouts and achieve some decent performance by
avoiding to be NoC limited.
It's also providing some power consumption improvement, but I have
only measured that as less heat, which is quite important when
working on thermally constrained devices like smartphones.
Please note that this driver's yaml binding is referring to a MMCC
clock, so this series does depend on the SDM660 MMCC driver that I
have sent separately.
The multimedia clock is required only for the Multimedia NoC (mnoc).
This patch series has been tested against the following devices:
- Sony Xperia XA2 Ultra (SDM630 Nile Discovery)
- Sony Xperia 10 (SDM630 Ganges Kirin)
- Sony Xperia 10 Plus (SDM636 Ganges Mermaid)
* icc-sdm660
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
interconnect: qcom: Add SDM660 interconnect provider driver
interconnect: qcom: sdm660: Fix kerneldoc warning
Link: https://lore.kernel.org/r/20201017133718.31327-1-kholk11@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is a link between the GEM NoC and C NoC nodes, which is currently
missing from the topology. Let's add it to allow consumers request paths
that use this link.
Reported-by: Alex Elder <elder@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094435.28937-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
For creating an array with the members for each NoC, we should be using
a local indexes, as otherwise unnecessary large arrays would be created.
Using an incorrect indexes will also result error for the consumers when
they try to find a valid path between the endpoints. Let's fix this and
use the correct ids.
Reported-by: Alex Elder <elder@linaro.org>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210401094334.28871-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SM8350 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Generated from downstream interconnect driver written by David Dai
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210318094617.951212-3-vkoul@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add slave RPM ID to assist with identifying incorrect RPM config.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20210205015205.22947-2-benl@squareup.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Introduce a driver for the Qualcomm interconnect busses found in
the SDM630/SDM636/SDM660 SoCs.
The topology consists of several NoCs that are controlled by a
remote processor that collects the aggregated bandwidth for each
master-slave pairs.
On a note, these chips are managing the "bus QoS" in a "hybrid"
fashion: some of the paths in the topology are managed through
(and by, of course) the RPM uC, while some others are "AP Owned",
meaning that the AP shall do direct writes to the appropriate
QoS registers for the specific paths and ports, instead of sending
an indication to the RPM and leaving the job to that one.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20201017133718.31327-3-kholk11@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When krealloc() fails and new is NULL, no error return code of
icc_link_destroy() is assigned.
To fix this bug, ret is assigned with -ENOMEM hen new is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210306132857.17020-1-baijiaju1990@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.
See commit c497f9322a ("interconnect: qcom: msm8916: Remove rpm-ids
from non-RPM nodes") where this was done for msm8916.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20210205015205.22947-3-benl@squareup.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SDX55 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Based on SM8250 driver and generated from downstream dts.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210121053254.8355-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in MSM8939 based
platforms. The topology consists of four NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-6-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use shared code for aggregate functionalities and probe function
to remove duplicated code.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-3-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add RPM based interconnect driver implements the set and aggregate
functionalities that translates bandwidth requests into RPM messages.
These modules provide a common set of functionalities for all
Qualcomm RPM based interconnect providers and should help reduce code
duplication when adding new providers.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-2-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add the icc_sync_state callback to notify the framework when consumers
are probed and the bandwidth doesn't have to be kept at maximum anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Suggested-by: Georgi Djakov <georgi.djakov@linaro.org>
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Link: https://lore.kernel.org/r/20201210100906.18205-6-martin.kepplinger@puri.sm
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When CONFIG_COMPILE_TEST is set, it is possible to build some
of the interconnect drivers into the kernel while their dependencies
are loadable modules, which is bad:
arm-linux-gnueabi-ld: drivers/interconnect/qcom/bcm-voter.o: in function `qcom_icc_bcm_voter_commit':
(.text+0x1f8): undefined reference to `rpmh_invalidate'
arm-linux-gnueabi-ld: (.text+0x20c): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2b0): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2e8): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: drivers/interconnect/qcom/icc-rpmh.o: in function `qcom_icc_bcm_init':
(.text+0x2ac): undefined reference to `cmd_db_read_addr'
arm-linux-gnueabi-ld: (.text+0x2c8): undefined reference to `cmd_db_read_aux_data'
The exact dependencies are a bit complicated, so split them out into a
hidden Kconfig symbol that all drivers can in turn depend on to get it
right.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201204165030.3747484-1-arnd@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=lkn4
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for 5.11
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...
Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.
Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=a7If
-----END PGP SIGNATURE-----
Merge tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.11
Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.
Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
MAINTAINERS: Add entry for Samsung interconnect drivers
interconnect: Add generic interconnect driver for Exynos SoCs
interconnect: qcom: Simplify the vcd compare function
The QUP nodes are currently defined just as entries in the topology,
but they are not referenced by any of the NoCs. Let's fix this and
"attach" them to their NoCs, so that the QUP drivers are able to use
them as path endpoints and scale their bandwidth.
This is based on the information from the downstream msm-4.9 kernel.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-2-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds a generic interconnect driver for Exynos SoCs in order
to provide interconnect functionality for each "samsung,exynos-bus"
compatible device.
The SoC topology is a graph (or more specifically, a tree) and its
edges are described by specifying in the 'interconnects' property
the interconnect consumer path for each interconnect provider DT node.
Each bus is now an interconnect provider and an interconnect node as
well (cf. Documentation/interconnect/interconnect.rst), i.e. every bus
registers itself as a node. Node IDs are not hard coded but rather
assigned dynamically at runtime. This approach allows for using this
driver with various Exynos SoCs.
Frequencies requested via the interconnect API for a given node are
propagated to devfreq using dev_pm_qos_update_request(). Please note
that it is not an error when CONFIG_INTERCONNECT is 'n', in which
case all interconnect API functions are no-op.
The samsung,data-clk-ratio DT property is used to specify the ratio
of the interconect bandwidth to the minimum data clock frequency
for each bus.
Due to unspecified relative probing order, -EPROBE_DEFER may be
propagated to ensure that the parent is probed before its children.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20201112140931.31139-3-s.nawrocki@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Let's simplify the cmp_vcd() function and replace the conditionals
with just a single statement, which also improves readability.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20201013171923.7351-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
of_count_icc_providers() function uses for_each_available_child_of_node()
helper to recursively check all the available nodes. This helper already
properly handles child nodes' reference count, so there is no need to do
it explicitly. Remove the excessive call to of_node_put(). This fixes
memory trashing when CONFIG_OF_DYNAMIC is enabled (for example
arm/multi_v7_defconfig).
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201119103746.32564-1-m.szyprowski@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The following errors are noticed during boot on a QCS404 board:
[ 2.926647] qcom_icc_rpm_smd_send mas 6 error -6
[ 2.934573] qcom_icc_rpm_smd_send mas 8 error -6
These errors show when we try to configure the GPU and display nodes.
Since these particular nodes aren't supported on RPM and are purely
local, we should just change their mas_rpm_id to -1 to avoid any
requests being sent for these master IDs.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201118111044.26056-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20201112105140.10092-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
It has been reported that on Fairphone 2 (msm8974-based), increasing
the clock rate for some of the NoCs during boot may lead to hangs.
Let's restore the original behavior and not touch the clock rate of
any of the NoCs to fix the regression.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Link: https://lore.kernel.org/r/20201109124512.10776-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When sync_state support got introduced recently, by default we try to
set the NoCs to run initially at maximum rate. But as these values are
aggregated, we may end with a really big clock rate value, which is
then converted from "u64" to "long" during the clock rate rounding.
But on 32bit platforms this may result an overflow. Fix it by making
sure that the rate is within range.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20201106144847.7726-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
In addition to the rest of Qcom interconnect drivers use icc_sync_state
for SM8150/SM8250 interconnect drivers to notify the interconnect
framework when all consumers are probed and there is no need to keep the
bandwidth set to maximum anymore.
Also move the BCM initialization before creating the nodes to set the
max bandwidth in hardware for the initialization/probing stage.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Link: https://lore.kernel.org/r/20201027133418.976687-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Take into account the initial bandwidth from the framework and update
the internal sum and max values before committing if needed. This will
ensure that the floor bandwidth values are enforced until the providers
get into sync state.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Tested-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20201021155938.9223-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-3-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-2-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When setting the initial bandwidth, make sure to call the aggregate()
function (if such is implemented for the current provider), to handle
cases when data needs to be aggregated first.
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
After enabling interconnect scaling for display on the db845c board,
in certain configurations the board hangs, while the following errors
are observed on the console:
Error sending AMC RPMH requests (-110)
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
...
In this specific case, the above is related to one of the sequencers
being stuck, while client drivers are returning from probe and trying
to disable the currently unused clock and interconnect resources.
Generally we want to keep the multimedia NoC enabled like the rest of
the NoCs, so let's set the keepalive flag on it too.
Fixes: aae57773fb ("interconnect: qcom: sdm845: Split qnodes into their respective NoCs")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20201012194034.26944-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902172433.1138-2-krzk@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902172433.1138-1-krzk@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* icc-syncstate:
interconnect: Add get_bw() callback
interconnect: Add sync state support
interconnect: qcom: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Lowering the bandwidth on the bus might have negative consequences if
it's done before all consumers had a chance to cast their vote. Now by
default the framework sets the bandwidth to maximum during boot. We need
to use the icc_sync_state callback to notify the framework when all
consumers are probed and there is no need to keep the bandwidth set to
maximum anymore.
Link: https://lore.kernel.org/r/20200825170152.6434-4-georgi.djakov@linaro.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The bootloaders often do some initial configuration of the interconnects
in the system and we want to keep this configuration until all consumers
have probed and expressed their bandwidth needs. This is because we don't
want to change the configuration by starting to disable unused paths until
every user had a chance to request the amount of bandwidth it needs.
To accomplish this we will implement an interconnect specific sync_state
callback which will synchronize (aggregate and set) the current bandwidth
settings when all consumers have been probed.
Link: https://lore.kernel.org/r/20200825170152.6434-3-georgi.djakov@linaro.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
These structures aren't modified at runtime. Mark them const so they get
moved to read-only memory. We have to cast away const in one place when
we store into the data member of struct icc_node. This is paired with a
re-const of the data member when it is extracted in qcom_icc_set().
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200914182112.513981-1-swboyd@chromium.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-7-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-5-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Implement a function to parse the arguments of the "interconnects" DT
property and populate the interconnect path tags if this information
is available.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200903133134.17201-4-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently there is the xlate() callback, which is used by providers for
mapping the nodes from phandle arguments. That's fine for simple mappings,
but the phandle arguments could contain an additional data, such as tag
information. Let's create another callback xlate_extended() for the cases
where providers want also populate the path tag data.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-2-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently, bcm-voter always assumes requests are made in KBps and that
BCM HW always wants them in Bps, so it always scales the requests by
1000. However, certain use cases and BCMs may use different units.
Thus, add support for BCM-specific scaling factors.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-7-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Change the default TCS wait behavior to only wait for completion in AMC
and WAKE. Waiting isn't necessary in the SLEEP TCS, since votes are only
being removed in this case. Resources can be safely disabled
asynchronously in parallel with the rest of the power collapse sequence.
This reduces the sleep entry latency.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-6-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently, all bcm-voters set tcs_cmd::wait=true for the last VCD
command in each TCS (AMC, WAKE, and SLEEP). However, some bcm-voters
don't need the completion and instead need to optimize for latency. For
instance, disabling wait-for-completion in the WAKE set can decrease
resume latency and allow for certain operations to occur in parallel
with the WAKE TCS triggering. This is only safe in very specific
situations. Keep the default behavior of always waiting, but allow it to
be overridden in devicetree.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-5-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add generic qcom interconnect bindings that are common across platforms. In
particular, these include QCOM_ICC_TAG_* macros that clients can use when
calling icc_set_tag().
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200903192149.30385-3-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SM8250 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Based on SC7180 driver and generated from downstream dts.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200728023811.5607-6-jonathan@marek.ca
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Georgi Djakov