If one leaves the CQSPI_REG_CMDCTRL in an unclean state this may cause
issues in future command reads. This issue came to light when some flash
reads in STIG mode were coming back dirty.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-2-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This Cadence QSPI IP has a 4-bit clock divisor field
for baud rate division. For example:
0b0000 = /2
0b0001 = /4
0b0010 = /6
...
0b1111 = /32
The maximum divisor is 32
(when div = CQSPI_REG_CONFIG_BAUD_MASK).
If we assume a reference clock of 500MHz and we set
our spi-max-frequency to something low, such as 10 MHz.
The calculated bit field for the divisor ends up being:
DIV_ROUND_UP(500000000/(2*10000000))-1 = 25
25 is 0b11001... which truncates to a divisor field of 0b1001 (or /20).
This is higher than our anticipated max-frequency of 10MHz
(500MHz/20 = 25 MHz). Instead, let's make sure we're always using
the maximum divisor (/32) in this case and give the user a warning about
the rate adjustment.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Link: https://lore.kernel.org/r/20221128164147.158441-1-nathan.morrison@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_{get_and}_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been o
work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in the
same message going to the same page.
- Update the fsl_spi driver to use transfer_one() rather than a custom
transfer function.
- Support for configuring transfer speeds with the AMD SPI controller.
- Support for a second chip select and 64K erase on Intel SPI.
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM62YIACgkQJNaLcl1U
h9CvPAf+MF1AzJJWH9DkR846KQh7Zt1rrujRuj5SGwvHewqjJcDtDmipAbM7mRFa
VPk6fCzfRE4btVywCDMEQX2ToB9VKBNUeP8ihVLddWrTddbkQ7hOKlTrz31dJ+6W
F9kwXkWcqWEpMYD/wr/25eT/kkNfv27oCyPU4dRQKoGGeF+zb9jYoj0+gPDl9Om8
ok7D1XAwY1wOqYqdPfl2thcUrBfoKtFvkTj+NNhqwuzWwIqfQHM2skwAjmD3fliQ
lLdRc54erCOqukDddIoWr348TyJIT4v1IXnkqY3cd7da6+kpixWae73o/7WIcQUR
4MrtPply0WWcapgU/46sCbHpjJNjjg==
=PDCv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:73d5fe0462702 ("spi: cadence-quadspi: Remove spi_master_put() in probe failure path")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On architecture where reading the SRAM is slower than the pace at
controller fills it, with interrupt enabled while reading from
SRAM FIFO causes unwanted interrupt storm to CPU.
The inner "bytes to read" loop never exits and waits for the completion
so it is enough to only enable the watermark interrupt when we
are out of bytes to read, which only happens when we start the
transfer (waiting for the FIFO to fill up initially) if the SRAM
is slow.
So only using read watermark interrupt, as the current implementation
doesn't utilize the SRAM full and indirect complete read interrupt.
And disable all the read interrupts while reading from SRAM.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Link: https://lore.kernel.org/r/20220813042616.1372110-1-niravkumar.l.rabara@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes: 606e5d4081 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently devres managed removal of the spi_controller happens after
removing the power domain of the host platform_device.While this
does not affect the clean removal of the controller, but affects
graceful removal of the child devices if the child device removal
requires issuing commands over SPI.
Eg. flash device being soft reset to 1S-1S-1S mode before removal
so that on next probe operations in 1S-1S-1S mode is successful.
Failure is seen when `rmmod spi-cadence-quadspi` is performed:
root@j7-evm:~# rmmod spi_cadence_quadspi
[ 49.230996] cadence-qspi 47050000.spi: QSPI is still busy after 500ms timeout.
[ 49.238209] spi-nor spi1.0: operation failed with -110
[ 49.244457] spi-nor spi1.0: Software reset failed: -110
and on subsequent modprobe the OSPI flash probe fails as it
is in 8D-8D-8D mode since the previous soft reset did not happen.
root@j7-evm:~# modprobe spi_cadence_quadspi
[ 73.253536] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 73.260476] spi-nor: probe of spi0.0 failed with error -2
This commit adds necessary changes to perform spi_unregister_master()
in the host device remove() so that the child devices are gracefully
removed before the power domain is removed.
changes tested on J721E with mt35xu512aba flash.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220511115516.14894-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series update flags management in the following cases:
- In APM mode, don't take care of TCF and TEF flags
- Always check TCF flag in stm32_qspi_wait_cmd()
- Don't check BUSY flag when sending new command
Remove a couple of unnecessary casts to `(void *)` when initializing the
`.data` members in the device ID table.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220510115141.212779-3-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
The Cadence QSPI compatible string required for the SoCFPGA platform
changed from the default "cdns,qspi-nor" to "intel,socfpga-qspi" with
the introduction of an additional quirk in
commit 98d948eb83 ("spi: cadence-quadspi: fix write completion support").
However, that change did not preserve the previously used
quirk for this platform. Reinstate the `CQSPI_DISABLE_DAC_MODE` quirk
for the SoCFPGA platform.
Fixes: 98d948eb83 ("spi: cadence-quadspi: fix write completion support")
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220427153446.10113-1-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085637.2541805-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
With the removal of the incorrect logic of cqspi_set_protocol(), ops with
cmd/addr buswidth >1 are now working correctly.
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash using 1-4-4
operations.
DTR operations are currently untested, so we leave them disabled for now
(except for the previously allowed 8-8-8 ops).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested, this removes the whole cqspi_set_protocol() function, as it
is not actually needed:
- Checks for unsupported operations are already handled by supports_op(),
removing the need to distinguish DTR and non-DTR modes in the buswidth
setup
- supports_op() ensures that the DTR flags match for all relevant parts of
an operation, so op->cmd.dtr can be used instead of copying the flag to
the cqspi_flash_pdata
- The logic in cqspi_set_protocol() is moved to cqspi_calc_rdreg() and
cqspi_write_setup() (with a helper macro CQSPI_OP_WIDTH())
The helper macro checks nbytes instead of buswidth for 0, for consistency
with supports_op() etc.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the conversion to spi-mem, the driver advertised support for
various operations that cqspi_set_protocol() was never expected to handle
correctly - in particuar all non-DTR operations with command or address
buswidth > 1. For DTR, all operations except for 8-8-8 would fail, as
cqspi_set_protocol() returns -EINVAL.
In non-DTR mode, this resulted in data corruption for SPI-NOR flashes that
support such operations. As a minimal fix that can be backported to stable
kernels, simply disallow the unsupported operations again to avoid this
issue.
Fixes: a314f63677 ("mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220406132832.199777-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cqspi_set_protocol() only set the data width, but ignored the command
and address width (except for 8-8-8 DTR ops), leading to corruption of
all transfers using 1-X-X or X-X-X ops. Fix by setting the other two
widths as well.
While we're at it, simplify the code a bit by replacing the
CQSPI_INST_TYPE_* constants with ilog2().
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash with 1-4-4
read and write operations.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220331110819.133392-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that spi_mem_default_supports_op() has access to the static
controller capabilities (relating to memory operations), and now that
these capabilities have been filled by the relevant controllers, there
is no need for a specific helper checking only DTR operations, so let's
just kill spi_mem_dtr_supports_op() and simply use
spi_mem_default_supports_op() instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-6-miquel.raynal@bootlin.com
This controller has DTR support, so advertize it with a capability now
that the spi-controller structure contains this new field. This will
later be used by the core to discriminate whether an operation is
supported or not, in a more generic way than having different helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-4-miquel.raynal@bootlin.com
Some versions of the Cadence QSPI controller does not have the write
completion register implemented(CQSPI_REG_WR_COMPLETION_CTRL). On the
Intel SoCFPGA platform the CQSPI_REG_WR_COMPLETION_CTRL register is
not configured.
Add a quirk to not write to the CQSPI_REG_WR_COMPLETION_CTRL register.
Fixes: 9cb2ff1117 ("spi: cadence-quadspi: Disable Auto-HW polling)
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211108200854.3616121-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There are separate constants for the dma-mapping API and the dmaengine
API, mixing them up causes a warning in some builds:
In file included from drivers/spi/spi-cadence-quadspi.c:12:
drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_versal_indirect_read_dma':
drivers/spi/spi-cadence-quadspi.c:950:55: error: implicit conversion from 'enum dma_transfer_direction' to 'enum dma_data_direction' [-Werror=enum-conversion]
950 | dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_DEV_TO_MEM);
| ^~~~~~~~~~~~~~
include/linux/dma-mapping.h:407:70: note: in definition of macro 'dma_unmap_single'
407 | #define dma_unmap_single(d, a, s, r) dma_unmap_single_attrs(d, a, s, r, 0)
| ^
Fixes: 1a6f854f7d ("spi: cadence-quadspi: Add Xilinx Versal external DMA support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013144600.2378037-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to read the data from the flash using external DMA.
Cadence Octal SPI Flash Controller has optional DMA peripheral interface
to communicate indirect mode of operations with external DMA.
Xilinx Versal OSPI has external DMA enabled, this will automatically
request the external DMA to fetch the data from SRAM. It supports only
reading the data from SRAM (DMA read) and doesn't support writing the
data to SRAM (DMA write).
Xilinx Versal OSPI read the data from the flash device using external DMA
and write the data to the flash device using software triggered
indirect mode.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/1632478031-12242-5-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OSPI support for Xilinx Versal SoCs.
Disable the Direct Access Controller for Xilinx Versal OSPI.
On Xilinx Versal platform, AXI interface need to be selected as Linear
mode (driven from interconnect rather than external DMA) to use
Software triggered 'indirect' mode of operation. This will be achieved
by calling Xilinx firmware API.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/1632478031-12242-4-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
buswidth and dtr fields in spi_mem_op are only valid when the
corresponding spi_mem_op phase has a non-zero length. For example,
SPI NAND core doesn't set buswidth when using SPI_MEM_OP_NO_ADDR
phase.
Fix the dtr checks in set_protocol() and suppports_mem_op() to
ignore empty spi_mem_op phases, as checking for dtr field in
empty phase will result in false negatives.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210716232504.182-3-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cadence-quadspi has a builtin Auto-HW polling funtionality using which
it keep tracks of completion of write operations. When Auto-HW polling
is enabled, it automatically initiates status register read operation,
until the flash clears its busy bit.
cadence-quadspi controller doesn't allow an address phase when
auto-polling the busy bit on the status register. Unlike SPI NOR
flashes, SPI NAND flashes do require the address of status register
when polling the busy bit using the read register operation. As
Auto-HW polling is enabled by default, cadence-quadspi returns a
timeout for every write operation after an indefinite amount of
polling on SPI NAND flashes.
Disable Auto-HW polling completely as the spi-nor core, spinand core,
etc. take care of polling the busy bit on their own.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210713125743.1540-2-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below division by zero warning:
- The reason for dividing by zero is because the dummy bus width is zero,
but if the dummy n bytes is zero, it indicates that there is no data transfer,
so we can just return zero without doing any calculations.
[ 0.795337] Division by zero in kernel.
:
[ 0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[ 0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)
Fixes: 7512eaf541 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/92eea403-9b21-2488-9cc1-664bee760c5e@nskint.co.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below division by zero warning:
- Added an if statement because buswidth can be zero, resulting in division by zero.
- The modified code was based on another driver (atmel-quadspi).
[ 0.795337] Division by zero in kernel.
:
[ 0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[ 0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)
Fixes: 7512eaf541 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/ed989af6-da88-4e0b-9ed8-126db6cad2e4@nskint.co.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
The conversion to new style transfer delay will cause an issue with a
newly added staging driver which has a straightforward resolution in
-next.
- Completion of the conversion to new style transfer delay
configuration.
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree.
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon Kunpeng,
MediaTek MT8195,
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmCG0FYACgkQJNaLcl1U
h9BXlAf/ZQaU8Nq4NY2jgjzjUoplF4qSFvCZ05CXqfYftaAOp06AmoOwNuNTz2gU
Fkxouuw3D0hNmaeVusF1PaRjIvJCu+RO68EDrzTJlcFytyC8CxWSDE4Yw6ytOBUM
OWZdVXsuw0CUk3VRJl2ycCooeTyKaCksfkVucocZAoyexcfQrFpxkOCUbA8hVM43
Hghzb8HWAZUerrfwreSwfvyVMralR3rqqbZFKgSgT/sRM3zpaR4sctIkNgKKEbFE
eRPRfBIWWZdJtjQ+uifFAc3jJHeZlmNXuQq3C+ETd2vQDFlymTxj+U3u74ieZxrm
c6V4u4R3+Qx9qONV/q0LV6E4sBSvdw==
=cBUy
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
Summary:
- Completion of the conversion to new style transfer delay
configuration
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon
Kunpeng, MediaTek MT8195"
* tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (113 commits)
spi: Rename enable1 to activate in spi_set_cs()
spi: Convert Freescale QSPI binding to json schema
spi: stm32-qspi: fix debug format string
spi: tools: make a symbolic link to the header file spi.h
spi: fsi: add a missing of_node_put
spi: Make error handling of gpiod_count() call cleaner
spidev: Add Micron SPI NOR Authenta device compatible
spi: brcm,spi-bcm-qspi: convert to the json-schema
spi: altera: Add DFL bus driver for Altera API Controller
spi: altera: separate core code from platform code
spi: stm32-qspi: Fix compilation warning in ARM64
spi: Handle SPI device setup callback failure.
spi: sync up initial chipselect state
spi: stm32-qspi: Add dirmap support
spi: stm32-qspi: Trigger DMA only if more than 4 bytes to transfer
spi: stm32-qspi: fix pm_runtime usage_count counter
spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails
spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op
spi: spi-zynqmp-gqspi: Resolved slab-out-of-bounds bug
spi: spi-zynqmp-gqspi: fix hang issue when suspend/resume
...
When initialize cadence qspi controller, it is need to set cqspi
to the driver_data field of struct device, because it will be
used in function cqspi_remove/suspend/resume(). Otherwise, there
will be a crash trace as below when invoking these finctions.
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210311091220.3615-1-Meng.Li@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-cadence-quadspi.c:267:18: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
return reg & (1 << CQSPI_REG_CONFIG_IDLE_LSB);
^
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1614854872-8694-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix OF node leaks by calling of_node_put in
for_each_available_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210215110425.1012-1-angkery@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newly introduced spi_mem_dtr_supports_op() to check DTR op
support. This means the buswidth check does not need to be replicated.
It also happens to fix a bug where STR ops with a 2-byte opcode would be
reported as supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210204141218.32229-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On Intel Lightning Mountain(LGM) SoCs QSPI controller do not use
Direct Access Controller(DAC).
This patch adds a quirk to disable the Direct Access Controller
for data transfer instead it uses indirect data transfe
DAC bit resets to 1 so there is no need to explicitly set it.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Link: https://lore.kernel.org/r/20201124041840.31066-3-vadivel.muruganx.ramuthevar@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel test robot reports the following warning.
drivers/spi/spi-cadence-quadspi.c:966:24: warning: comparison of distinct pointer types ('typeof (len) *' (aka 'unsigned int *') and 'typeof (500UL) *' (aka 'unsigned long *')) [-Wcompare-distinct-pointer-types]
msecs_to_jiffies(max(len, 500UL)))) {
^~~~~~~~~~~~~~~
include/linux/minmax.h:58:19: note: expanded from macro 'max'
#define max(x, y) __careful_cmp(x, y, >)
^~~~~~~~~~~~~~~~~~~~~~
include/linux/minmax.h:42:24: note: expanded from macro '__careful_cmp'
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~~~~~~~
include/linux/minmax.h:32:4: note: expanded from macro '__safe_cmp'
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~~~~~~~
include/linux/minmax.h:18:28: note: expanded from macro '__typecheck'
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
1 warning generated.
This happens because size_t is unsigned long on 64-bit platforms like
arm64 but it is unsigned int on 32-bit platforms like arm. Omitting the
"UL" would result in a warning on 64-bit platforms. Squash it by type
casting the arguments to size_t using max_t(). This way builds on both
type of platforms can be satisfied. There is no chance of any truncation
since 500 is small enough to fit into both int and long.
Fixes: f453f29397 ("spi: cadence-quadspi: Wait at least 500 ms for direct reads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210108181457.30291-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a new warning report by build for make ARCH=MIPS allmodconfig:
drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_direct_read_execute':
./include/linux/minmax.h:18:28: warning: comparison of distinct pointer types lacks a cast
18 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^~
./include/linux/minmax.h:32:4: note: in expansion of macro '__typecheck'
32 | (__typecheck(x, y) && __no_side_effects(x, y))
| ^~~~~~~~~~~
./include/linux/minmax.h:42:24: note: in expansion of macro '__safe_cmp'
42 | __builtin_choose_expr(__safe_cmp(x, y), \
| ^~~~~~~~~~
./include/linux/minmax.h:58:19: note: in expansion of macro '__careful_cmp'
58 | #define max(x, y) __careful_cmp(x, y, >)
| ^~~~~~~~~~~~~
drivers/spi/spi-cadence-quadspi.c:1153:24: note: in expansion of macro 'max'
1153 | msecs_to_jiffies(max(len, 500UL)))) {
| ^~~
"len" is unsigned,however,"500" is unsigned long.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20210107115704.3835282-1-siyanteng@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Double Transfer Rate (DTR) mode transfers data twice per clock cycle.
Add support for parsing DTR ops and set up the registers to allow it.
Most SPI NOR flashes expect 2 byte commands. Parse the 2-byte opcode
from SPI MEM and set it up in the CQSPI_REG_OP_EXT_LOWER register.
Increment the delay needed before issuing indirect writes because larger
delay is needed for DTR mode. With the current delay some writes end up
missing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-8-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a direct read via DMA the timeout for completion is set
equal to the read length. This is fine for larger reads. For a small
read like the Read Status Register command, the timeout would be 1 or 2
milliseconds. This is not enough to cover the overhead needed in setting
up DMA.
Make sure the timeout is at least 500 ms to allow DMA ample time to
finish. For reads larger than 500 bytes, the timeout will continue to be
equal to the read length.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201222184425.7028-7-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default SPI MEM supports_op hook rejects DTR ops by default. Add a
simple supports_op hook that very closely imitates the SPI MEM one. It
will be extended in later commits to allow DTR ops.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-6-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI MEM deals with dummy bytes but the controller deals with dummy
cycles. Multiplying bytes by 8 is correct if the dummy phase uses 1S
mode since 1 byte will be sent in 8 cycles. But if the dummy phase uses
4S mode then 1 byte will be sent in 2 cycles.
To correctly translate dummy bytes to dummy cycles, the dummy buswidth
also needs to be taken into account. Divide 8 by the buswidth to get the
correct multiplier for getting the number of cycles.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a command does not have an address phase it goes via the STIG path.
The dummy cycles are not initialized for the STIG commands. As a result,
STIG commands with dummy cycles will not work.
Initialize the dummy cycle field before issuing the STIG command to make
sure it is sent correctly. Move the code to calculate dummy cycle value
to a separate function so it is not repeated twice. DTR support will add
some more logic here to it is worth it to extract it out in a function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit 9326e4f1e5 ("spi: Limit the spi device max speed to
controller's max speed"), the SPI device max speed is set to the
controller's max speed if it is larger. The Cadence QSPI controller does
not set the controller's max speed so it is left at its initial value of
0. This means the SPI device max speed is always set to 0.
The SPI device max speed is used to calculate the baud rate divider when
performing an operation. If this speed is 0, the default divider of 32
is used. No matter what speed is specified by the device tree property
'spi-max-frequency', the device will always operate at ref_clk / 32.
Fix this by setting master->max_speed_hz to the ref clock speed so the
correct divider can be calculated.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return the error code from
devm_reset_control_get_optional_exclusive() instaed of 0
in cqspi_probe().
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201116141836.2970579-1-chengzhihao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-5-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Buffers need to mapped to DMA channel's device pointer instead of SPI
controller's device pointer as its system DMA that actually does data
transfer.
Data inconsistencies have been reported when reading from flash
without this fix.
Fixes: ffa639e069 ("mtd: spi-nor: cadence-quadspi: Add DMA support for direct mode reads")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200831130720.4524-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement get_name() interface of spi_controller_mem_ops so as to avoid
changing of mtd->name due to driver being moved over to spi-mem
framework from SPI NOR. This avoids breaking of MTD cmdline args being
passed by bootloaders which maybe using old driver name.
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200825172506.14375-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dhruva Gole