The H.264 specification requires in section 7.4.3 "Slice header semantics",
that the following values shall be the same in all slice headers:
pic_parameter_set_id
frame_num
field_pic_flag
bottom_field_flag
idr_pic_id
pic_order_cnt_lsb
delta_pic_order_cnt_bottom
delta_pic_order_cnt[ 0 ]
delta_pic_order_cnt[ 1 ]
sp_for_switch_flag
slice_group_change_cycle
These bitstream fields are part of the slice header, and therefore
passed redundantly on each slice. The purpose of the redundancy
is to make the codec fault-tolerant in network scenarios.
This is of course not needed to be reflected in the V4L2 controls,
given the bitstream has already been parsed by applications.
Therefore, move the redundant fields to the per-frame decode
parameters control (DECODE_PARAMS).
Field 'pic_parameter_set_id' is simply removed in this case,
because the PPS control must currently contain the active PPS.
Syntax elements dec_ref_pic_marking() and those related
to pic order count, remain invariant as well, and therefore,
the fields dec_ref_pic_marking_bit_size and pic_order_cnt_bit_size
are also common to all slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, the SLICE_BASED and FRAME_BASED modes documentation
is misleading and not matching the intended use-cases.
Drop non-required fields SLICE_PARAMS 'start_byte_offset' and
DECODE_PARAMS 'num_slices' and clarify the decoding modes in the
documentation.
On SLICE_BASED mode, a single slice is expected per OUTPUT buffer,
and therefore 'start_byte_offset' is not needed (since the offset
to the slice is the start of the buffer).
This mode requires the use of CAPTURE buffer holding, and so
the number of slices shall not be required.
On FRAME_BASED mode, the devices are expected to take care of slice
parsing. Neither SLICE_PARAMS are required (and shouldn't be
exposed by frame-based drivers), nor the number of slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SLICE_PARAMS control is intended for slice-based
devices. In this mode, the OUTPUT buffer contains
a single slice, and so the buffer's plane payload size
can be used to query the slice size.
To reduce the API surface drop the size from the
SLICE_PARAMS control.
A follow-up change will remove other members in SLICE_PARAMS
so we don't need to add padding fields here.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
DPB entry PicNum maximum value is 2*MaxFrameNum for interlaced
content (field_pic_flag=1).
As specified, MaxFrameNum is 2^(log2_max_frame_num_minus4 + 4)
and log2_max_frame_num_minus4 is in the range of 0 to 12,
which means pic_num should be a 32-bit field.
The v4l2_h264_dpb_entry struct needs to be padded to avoid a hole,
which might be also useful to allow future uAPI extensions.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As discussed recently, the current interface for the
Decoded Picture Buffer is not enough to properly
support field coding.
This commit introduces enough semantics to support
frame and field coding, and to signal how DPB entries
are "used for reference".
Reserved fields will be added by a follow-up commit.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Slice header syntax element 'first_mb_in_slice' can point
to the last macroblock, currently the field can only reference
65536 macroblocks which is insufficient for 8K videos.
Although unlikely, a 8192x4320 video (where macroblocks are 16x16),
would contain 138240 macroblocks on a frame.
As per the H264 specification, 'first_mb_in_slice' can be up to
PicSizeInMbs - 1, so increase the size of the field to 32-bits.
Note that v4l2_ctrl_h264_slice_params struct will be modified
in a follow-up commit, and so we defer its 64-bit padding.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since pic_order_cnt_bit_size is not a syntax element itself, explicitly
state that it is the total size in bits of the pic_order_cnt_lsb,
delta_pic_order_cnt_bottom, delta_pic_order_cnt[0], and
delta_pic_order_cnt[1] syntax elements contained in the slice.
[Ezequiel: rebase]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The prediction weight parameters are only required under
certain conditions, which depend on slice header parameters.
As specified in section 7.3.3 Slice header syntax, the prediction
weight table is present if:
((weighted_pred_flag && (slice_type == P || slice_type == SP)) || \
(weighted_bipred_idc == 1 && slice_type == B))
Given its size, it makes sense to move this table to its control,
so applications can avoid passing it if the slice doesn't specify it.
Before this change struct v4l2_ctrl_h264_slice_params was 960 bytes.
With this change, it's 188 bytes and struct v4l2_ctrl_h264_pred_weight
is 772 bytes.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 0b0393d59e ("media: uapi: h264: clarify
expected scaling_list_4x4/8x8 order") improved the
documentation on H264 scaling lists order.
This commit improves the documentation by clarifying
that the lists themselves are expected in raster scan order.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When dealing with interlaced frames, reference lists must tell if
each particular reference is meant for top or bottom field. This info
is currently not provided at all in the H264 related controls.
Change reference lists to hold a structure, which specifies
an index into the DPB array and the field/frame specification
for the picture.
Currently the only user of these lists is Cedrus which is just compile
fixed here. Actual usage of will come in a following commit.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The unit of exposure value is different from other OmniVision sensors,
driver will divide by 2 before set register, the exposure range exposed
by v4l2 ctrl to user should be same as others, so the calculation for
the maximum exposure value in current driver need be fixed.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While we have had some example drivers, there has been up to date no
formal documentation on how camera sensor drivers should be written; what
are the practices, why, and where they apply.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis reports this error
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the error return from the call to max9286_read is masked
with 0xf0 so the following check for a negative error return is
never true. Fix this by checking for an error first, then masking
the return value for subsequent conflink_mask checking.
Addresses-Coverity: ("Logically dead code")
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Although the code is correct and doing the right thing, the clock diagram
showed the wrong register for the bit divider, which had me doubting the
understanding of the tree. Fix this to avoid doubts in the future.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix improper line breaks and format all example yavta and media-ctl
commands as code blocks to improve readability.
Signed-off-by: Jordan Hand <jorhand@linux.microsoft.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the current maintainer email address bounces back, replace
the entry and make myself and Dave Stevenson maintainers of the driver.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document in dt-schema bindings for the ov5647 sensor the optional
'pwdn-gpios' property.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes a multiline comment style warning as found by checkpatch.pl.
Signed-off-by: Rahul Gottipati <rahul.blr97@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the typo in email address of Tianshu Qiu and correct the name.
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OTP data was not ready after registered as nvmem device, it is
risky as the nvmem read may happen once the device exists, this patch
get the OTP data ready before registering the nvmem device. OTP data
missing should not break the normal camera sensor probe, so use a
warning instead of an error message.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The parallel port nodes should be numbered 1 and 2, not 0 and 1
for A and B respectively. The driver has always implemented 1
and 2 and the in-tree Goni DTS uses 1 as port A as well. Update
the documentation to match this behaviour.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vidioc_streamoff can be called multiple times from userspace, but we
should only call media_pipeline_stop when we're actually setup.
This became more noticeable after commit 2a2599c663 ("[media] media:
entity: Catch unbalanced media_pipeline_stop calls") was merged as it
added a WARN for unbalanced calls to media_pipeline_stop.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is no longer used since the conversion to DT
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a no-op as it is never set and is a remnant from non-DT days
that can be safely removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some devices, there may be multiple camera sensors attached
to the same port. Make sure we probe all of them, not just the
first one.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of keeping a local copy of how many sensors we've probed
(which may not even properly represent the number of sensors
probed if we have a port without a sensor), use the global
num_sensors counter that has the actual number used.
This will also make it easier to add support for multiple sensors
being connected to the same port.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ee7160e57c ("[media] s5p-fimc: Add support for JPEG capture")
added support for JPEG capture, but missed setting a register when the
parallel port was used rather than the CSIS device.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit bae4500399 ("[media] exynos4-is: Add missing entity function
initialization") tried to suppress the warnings such as
s5p-fimc-md camera: Entity type for entity FIMC.0 was not initialized!
However, this missed setting for the subdev. Set it now to avoid the
ugly warnings on boot.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Not all devices use the CSIS device, some may use the FIMC directly in
which case the CSIS device isn't registered. This leads to a nullptr
exception when starting the stream as the CSIS device is always
referenced. Instead, if getting the CSIS device fails, try getting the
FIMC directly to check if we are using the subdev API
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On FIMC variants which don't have writeback channel, there is no need to
access system registers. This patch makes the driver request sysreg
regmap conditionally depending on whether writeback is supported.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The S5PV210 platform only supports device tree based booting
where the FIMC variant data is parsed directly from
the device tree, hence the now unused static data can be removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the post-processor is enabled, the driver allocates
"shadow buffers" which are used for the decoder core,
and exposes the post-processed buffers to userspace.
For this reason, extra motion vector space has to
be allocated on the shadow buffers, which the driver
wasn't doing. Fix it.
This fix should address artifacts on high profile bitstreams.
Fixes: 8c2d66b036 ("media: hantro: Support color conversion via post-processing")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the bitstream and the application are incorrectly configuring
the reference pictures, the hardware will need to fallback
to using some other reference picture.
When the post-processor is enabled, the fallback buffer
should be a shadow buffer (postproc.dec_q), and not a
CAPTURE queue buffer, since the latter is post-processed
and not really the output of the decoder core.
Fixes: 8c2d66b036 ("media: hantro: Support color conversion via post-processing")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
list_for_each_entry is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry is defined in terms of list_first_entry,
which indicates that it should not be used on an empty list. But in
list_for_each_entry, the element obtained by list_first_entry is not
really accessed, only the address of its list_head field is compared
to the address of the list head, so the list_first_entry is safe.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each_entry(i,x,...) S
- }
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
list_for_each_safe is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_safe(i,j,x) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
list_for_each_entry is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry is defined in terms of list_first_entry,
which indicates that it should not be used on an empty list. But in
list_for_each_entry, the element obtained by list_first_entry is not
really accessed, only the address of its list_head field is compared
to the address of the list head, so the list_first_entry is safe.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each_entry(i,x,...) S
- }
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver access struct's fields one by one, they are not blindly
copied to/from the hardware, so we can remove __packed from the
structs.
Tested on Scarlet Chromebook with ChromeOS stack and verified images
with the Camera app.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
