The driver provides overwatch of the cm behavior by maintaining a set of rx
I/O statistics. This information is also used in later updating of the cm
statistics buffer.
Link: https://lore.kernel.org/r/20210816162901.121235-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Complete the enablement of the cm framework feature in the adapter. Perform
the following:
- Detect the presence of the congestion management framework feature.
When the cm framework is present:
- Issue the SET_FEATURE command to enable the feature.
- Register the cm statistics buffer with the adapter.
- Read the cm enablement buffer to determine the cm framework state for cm
management.
When cm management is enabled:
- Monitor all FPIN and congestion signalling events, incrementing
counters.
- Regularly sync with the adapter to communicate congestion events and to
receive an rx request limit.
- Monitor requests for rx data and ensure that no more than the
adapter prescribed limit is issued on the link. If the limit is
exceeded, SCSI and/or NVMe traffic is temporarily suspended.
- Maintain the minute, hourly, daily statistics buffer.
- Monitor for congestion enablement change events, causing a reread of the
enablement buffer and acting on any change in enablement.
And:
- Add teardown logic, including buffer deregistration, on adapter
detachment or reset.
Link: https://lore.kernel.org/r/20210816162901.121235-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When congestion mgmt is enabled, cmf has the driver regularly issue a
command to synchronize reporting of congestion mgmt events such as fpin and
signal delivery.
This patch adds the definition of the CMF_SYNC WQE and its CQE fields as
well as support for issuing the command. The patch also adds the few
remaining cmf-related SLI additions, such as feature definition for
enablement of CMF and notifications to the driver if the cm enablement mode
changes.
Link: https://lore.kernel.org/r/20210816162901.121235-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of the cmf framework, the firmware maintains a table with
congestion related state information, specifically whether enabled and if
enabled, whether monitoring or actively managing congestion.
Add definition of the table and add support to read the table from the
adapter and determine if it is enabled. In support of this, the READ_OBJECT
mailbox command definition is added to the driver.
Link: https://lore.kernel.org/r/20210816162901.121235-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cmf framework requires the driver to maintain a cm statistics table,
accessible inband, of congestion related statistics that are reported per
minute, rolled up to per hour, and rolled up again per day. Several days
worth may be maintained. The table is registered with the adapter when the
MIB feature is enabled.
Add definition of the table and add support to register the table with the
adapter. Includes definition and initialization of event counters that are
later added to the statistics table.
Link: https://lore.kernel.org/r/20210816162901.121235-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When congestion management is enabled, issue EDC ELS to register congestion
signaling capabilities with the fabric. The response handling will process
the fabric parameters and set the reporting parameters.
Similarly, add support for receiving an EDC request from the fabric
generating a corresponding response.
Implement handlers for congestion signals from the fabric and maintain
statistics for them.
Link: https://lore.kernel.org/r/20210816162901.121235-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expand FPIN logging:
- Display Attached Port Names for Link Integrity and Peer Congestion
events
- Log Delivery, Peer Congestion, and Congestion events
- Sanity check FPIN descriptor lengths when processing FPIN descriptors.
Log RDF events when congestion logging is enabled.
Link: https://lore.kernel.org/r/20210816162901.121235-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MIB support is currently limited to detecting support in the adapter and
ensuring FDMI support is enabled if present. For the new framework MIB
support also requires active enablement of support via the SET_FEATURES
command with the firmware.
Rework the MIB detection and enablement for the following:
- Move detection away from the get_sli4_parameters routine, and into the
hba_setup path. get_sli4_parameters is only called once at attachment
while hba_setup is called as part of any SLI port reset path. This
ensures detection after firmware download.
- Update SET_FEATURES mbx command for the MIB enablement feature and add
support for the feature.
- Create the cmf_setup routine to encapsulate the detection of MIB support
and perform the enablement of the MIB support feature.
Link: https://lore.kernel.org/r/20210816162901.121235-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement the SET_HOST_DATA mbox command to set date / time during
initialization. It is used by the firmware for various purposes including
congestion management and firmware dumps.
Link: https://lore.kernel.org/r/20210816162901.121235-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-28-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_sli4_nvmet_xri_aborted() routine takes out the abts_buf_list_lock
and traverses the buffer contexts to match the xri. Upon match, it then
takes the context lock before potentially removing the context from the
associated buffer list. This violates the lock hierarchy used elsewhere in
the driver of locking context, then the abts_buf_list_lock - thus a
possible deadlock.
Resolve by: after matching, release the abts_buf_list_lock, then take the
context lock, and if to be deleted from the list, retake the
abts_buf_list_lock, maintaining lock hierarchy. This matches same list lock
hierarchy as elsewhere in the driver
Link: https://lore.kernel.org/r/20210730163309.25809-1-jsmart2021@gmail.com
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer pcmd is being initialized with a value that is never read, the
assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210721095350.41564-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
Update copyrights to 2021 for files modified in the 14.0.0.0 patch set.
Link: https://lore.kernel.org/r/20210722221721.74388-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 14.0.0.0.
Link: https://lore.kernel.org/r/20210722221721.74388-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update routines to support 256 Gb link speed for LPe37000/LPe38000
adapters. 256 Gb speeds can be seen on trunk links.
Link: https://lore.kernel.org/r/20210722221721.74388-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support for Topology and RAS logging capabilities were qualified by PCIe
device ID checks necessitating additional driver changes for new device
IDs.
Reduce reliance on specific PCIe device IDs by substituting checks for SLI
family information. This automatically picks up support on the newest
hardware.
Link: https://lore.kernel.org/r/20210722221721.74388-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On the newer hardware, CQ_ID values can be larger than seen on previous
generations. This exposed an issue in the driver where its definition of
cq_id in the RQ Create mailbox cmd was too small, thus the cq_id was
truncated, causing the command to fail.
Revise the RQ_CREATE CQ_ID field to its proper size (16 bits).
Link: https://lore.kernel.org/r/20210722221721.74388-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update supported pci_device_id table to include the values for the G7+ ASIC
Device ID utilized by LPe37xxx and LPe38xxx series of adapters. The
default reporting string will be "LPe38000".
Link: https://lore.kernel.org/r/20210722221721.74388-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights for files modified by the 12.8.0.11 patch set.
Link: https://lore.kernel.org/r/20210707184351.67872-21-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.11.
Link: https://lore.kernel.org/r/20210707184351.67872-20-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a node moves to NPR state due to a device recovery event, the
nlp_fc4_types in the node are cleared. An ADISC received for a node in the
NPR state triggers an ADISC. Without fc4 types being known, the calls to
register with the transport are no-op'd, thus no additional references are
placed on the node by transport re-registrations. A subsequent RSCN could
trigger another unregister request, which will decrement the reference
counts, leading to the ref count hitting zero and the node being freed
while futher discovery on the node is being attempted by the RSCN event
handling.
Fix by skipping the trigger of an ADISC when in NPR state. The normal ADISC
process will kick off in the regular discovery path after receiving a
response from name server.
Link: https://lore.kernel.org/r/20210707184351.67872-19-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During RSCN storms, some instances of LIP on SLI-3 adapters lead to a
situation where FLOGIs keep failing with firmware indicating an illegal
command error code. This situation was preceded by an ADISC completion
that was processed while the link was down. This path on SLI-3 performs a
CLEAR_LA and attempts to activate a VPI with REG_VPI. Later, as the FLOGI
completes, it's no longer in sync with the VPI state. In SLI-3 it is
illegal to have an active VPI during FLOGI.
Resolve by circumventing the SLI-3 path that performs the CLEAR_LA and
REG_VPI. The path will be taken after the FLOGI after the next Link Up.
Link: https://lore.kernel.org/r/20210707184351.67872-18-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the PLOGI and ADISC completion handling, the device removal event could
be skipped during some link errors. This could leave a stale node in UNUSED
state. Driver unload would hang for a long time waiting for this node to
be freed.
Resolve by taking the following steps:
- Always post ADISC completion events to discovery state machine upon
ADISC completion.
- In case of a completion error for PLOGI/ADISC, ensure that init refcount
is dropped if not registered with transport.
Link: https://lore.kernel.org/r/20210707184351.67872-17-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an RSCN event, the nodes specified in RSCN payload and in MAPPED state
are moved to NPR state in order to revalidate the login. This triggers an
immediate unregister from SCSI/NVMe backend. The assumption is that the
node may be missing. The re-registration with the backend happens after
either relogin (PLOGI/PRLI; if ADISC is disabled or login truly lost) or
when ADISC completes successfully (rediscover with ADISC enabled).
However, the NVMe-FC standard provides for an RSCN to be triggered when
the remote port supports a discovery controller and there was a change
of discovery log content. As the remote port typically also supports
storage subsystems, this unregister causes all storage controller
connections to fail and require reconnect.
Correct by reworking the code to ensure that the unregistration only occurs
when a login state is truly terminated, thereby leaving the NVMe storage
controllers in place.
The changes made are:
- Retain node state in ADISC_ISSUE when scheduling ADISC ELS retry.
- Do not clear wwpn/wwnn values upon ADISC failure.
- Move MAPPED nodes to NPR during RSCN processing, but do not unregister
with transport. On GIDFT completion, identify missing nodes (not marked
NLP_NPR_2B_DISC) and unregister them.
- Perform unregistration for nodes that will go through ADISC processing
if ADISC completion fails.
- Successful ADISC completion will move node back to MAPPED state.
Link: https://lore.kernel.org/r/20210707184351.67872-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Assign a default value of 1 to driver module parameter lpfc_use_adisc.
Link: https://lore.kernel.org/r/20210707184351.67872-15-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SLI4 interface changed the manner used to indicate PBDE support.
Rework the driver to check for PBDE support via the PBDE feature bit in
COMMON_GET_SLI4_PARAMETERS.
Link: https://lore.kernel.org/r/20210707184351.67872-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mailbox commands sent via ioctl/bsg from user applications may be
interrupted from processing by a concurrently triggered PCI function
reset. The command will not generate a completion due to the reset. This
results in a user application hang waiting for the mailbox command to
complete.
Resolve by changing the function reset handler to detect that there was an
outstanding mailbox command and simulate a mailbox completion. Add some
additional debug when a mailbox command times out.
Link: https://lore.kernel.org/r/20210707184351.67872-13-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_offline_prep() an RPI is freed and nlp_rpi set to 0xFFFF before
calling lpfc_unreg_rpi(). Unfortunately, lpfc_unreg_rpi() uses nlp_rpi to
index the sli4_hba.rpi_ids[] array.
In lpfc_offline_prep(), unreg rpi before freeing the rpi.
Link: https://lore.kernel.org/r/20210707184351.67872-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the REG_LOGIN to the fabric controller happens in parallel with SCR,
it may or may not be completed by the time RDF is sent. RDF and SCR are
sent to the fabric in parallel, so checking for a completed REG_LOGIN in
the RDF submit path is not needed.
Remove the REG_LOGI check from the RDF submission path.
Link: https://lore.kernel.org/r/20210707184351.67872-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ELS job request structure, that is allocated while issuing ELS RDF/SCR
request path, is not being released in an error path causing a memory leak
message on driver unload.
Free the ELS job structure in the error paths.
Link: https://lore.kernel.org/r/20210707184351.67872-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RDF ELS handling for NPIV ports may result in an incorrect NDLP reference
count. In the event of a persistent link down, this may lead to premature
release of an NDLP structure and subsequent NULL ptr dereference panic.
Remove extraneous lpfc_nlp_put() call in NPIV port RDF processing.
Link: https://lore.kernel.org/r/20210707184351.67872-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the routine that generically cleans up an ELS after completion, the NDLP
put is done prior to the freeing of the IOCB. The IOCB may reference the
NDLP.
Move the lpfc_nlp_put() after freeing the IOCB.
Link: https://lore.kernel.org/r/20210707184351.67872-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous logic accidentally overrides the status variable to FAILURE when
target reset status is SUCCESS.
Refactor the non-SUCCESS logic of lpfc_vmid_vport_cleanup(), which resolves
the false override.
Link: https://lore.kernel.org/r/20210707184351.67872-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a LOGO is received for a node that is in the NPR state, post a DEVICE_RM
event to allow clean up of the logged out node.
Clearing the NLP_NPR_2B_DISC flag upon receipt of a LOGO ACC may cause
skipping of processing outstanding PLOGIs triggered by parallel RSCN
events. If an outstanding PLOGI is being retried and receipt of a LOGO ACC
occurs, then allow the discovery state machine's PLOGI completion to clean
up the node.
Link: https://lore.kernel.org/r/20210707184351.67872-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update comment headers for functions lpfc_vmid_cmd and lpfc_vmid_poll.
Link: https://lore.kernel.org/r/20210707184351.67872-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define additional status fields in mailbox commands to help provide
additional information when downloading new firmware.
Link: https://lore.kernel.org/r/20210707184351.67872-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are instances when trace event logs are triggered from an interrupt
context. The trace event log may attempt to alloc memory causing scheduling
while atomic bug call traces.
Remove the need for the kmalloc'ed vport array when checking the
log_verbose flag, which eliminates the need for any allocation.
Link: https://lore.kernel.org/r/20210707184351.67872-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NVMe support indicator in log message 6422 is displaying a field that
was initialized but never set to indicate NVMe support. Remove obsolete
nvme_support element from the lpfc_hba structure and change log message to
display NVMe support status as reported in SLI4 Config Parameters mailbox
command.
Link: https://lore.kernel.org/r/20210707184351.67872-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers. The major core change is a rework
to drop the status byte handling macros and the old bit shifted
definitions and the rest of the updates are minor fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYN7I6iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXpRAQCkngYZ
35yQrqOxgOk2pfrysE95tHrV1MfJm2U49NFTwAEAuZutEvBUTfBF+sbcJ06r6q7i
H0hkJN/Io7enFs5v3WA=
=zwIa
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers.
The major core change is a rework to drop the status byte handling
macros and the old bit shifted definitions and the rest of the updates
are minor fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (287 commits)
scsi: aha1740: Avoid over-read of sense buffer
scsi: arcmsr: Avoid over-read of sense buffer
scsi: ips: Avoid over-read of sense buffer
scsi: ufs: ufs-mediatek: Add missing of_node_put() in ufs_mtk_probe()
scsi: elx: libefc: Fix IRQ restore in efc_domain_dispatch_frame()
scsi: elx: libefc: Fix less than zero comparison of a unsigned int
scsi: elx: efct: Fix pointer error checking in debugfs init
scsi: elx: efct: Fix is_originator return code type
scsi: elx: efct: Fix link error for _bad_cmpxchg
scsi: elx: efct: Eliminate unnecessary boolean check in efct_hw_command_cancel()
scsi: elx: efct: Do not use id uninitialized in efct_lio_setup_session()
scsi: elx: efct: Fix error handling in efct_hw_init()
scsi: elx: efct: Remove redundant initialization of variable lun
scsi: elx: efct: Fix spelling mistake "Unexected" -> "Unexpected"
scsi: lpfc: Fix build error in lpfc_scsi.c
scsi: target: iscsi: Remove redundant continue statement
scsi: qla4xxx: Remove redundant continue statement
scsi: ppa: Switch to use module_parport_driver()
scsi: imm: Switch to use module_parport_driver()
scsi: mpt3sas: Fix error return value in _scsih_expander_add()
...
Integration with VMID patches resulted in a build error when
CONFIG_DEBUG_FS is disabled and driver option CONFIG_SCSI_LPFC_DEBUG_FS is
disabled.
It results in an undefined variable:
lpfc_scsi:5595:3: error: 'uuid' undeclared (first use in this function); did you mean 'upid'?
Link: https://lore.kernel.org/r/20210618171842.79710-1-jsmart2021@gmail.com
Fixes: 33c79741de ("scsi: lpfc: vmid: Introduce VMID in I/O path")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using list_move_tail() instead of list_del() + list_add_tail().
Link: https://lore.kernel.org/r/1623113493-49384-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce the VMID in the I/O path. Check if the VMID is enabled and if
the I/O belongs to a VM or not.
Link: https://lore.kernel.org/r/20210608043556.274139-14-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a periodic check for issuing of QFPA command and VMID timeout in the
worker thread. The inactivity timeout check is added via the timer
function.
Link: https://lore.kernel.org/r/20210608043556.274139-13-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement timeout functionality for the VMID. After the set time period of
inactivity, the VMID is deregistered from the switch.
Link: https://lore.kernel.org/r/20210608043556.274139-12-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the VMID in wqe before sending out the request. The type of VMID
depends on the configured type and is checked before being appended.
Link: https://lore.kernel.org/r/20210608043556.274139-11-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement CT commands for registering and deregistering the appid for the
application. Also, a small change in decrementing the ndlp ref counter has
been added.
Link: https://lore.kernel.org/r/20210608043556.274139-10-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement routines to save, retrieve, and remove the VMIDs from the data
structure. A hash table is used to save the VMIDs and the corresponding
UUIDs associated with the application/VMs.
Link: https://lore.kernel.org/r/20210608043556.274139-9-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement ELS commands QFPA and UVEM for the priority tagging appid
support.
Link: https://lore.kernel.org/r/20210608043556.274139-8-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add supporting datastructures for mailbox command which helps in
determining if the firmware supports appid. Allocate resources for VMID at
initialization time and clean them up on removal.
Link: https://lore.kernel.org/r/20210608043556.274139-7-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Initialize parameters such as type of VMID, max number of VMIDs supported
and timeout value for the VMID registration based on the user input.
Link: https://lore.kernel.org/r/20210608043556.274139-6-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the primary datastructures needed to implement VMID in the lpfc
driver. Maintain the capability, current state, and hash table for the
vmid/appid along with other information. This implementation supports the
two versions of vmid implementation (app header and priority tagging).
Link: https://lore.kernel.org/r/20210608043556.274139-5-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The abort_cmd_ia flag in an abort wqe describes whether an ABTS basic link
service should be transmitted on the FC link or not. Code added in
lpfc_sli4_issue_abort_iotag() set the abort_cmd_ia flag incorrectly,
surpressing ABTS transmission.
A previous LPFC change to build an abort wqe inverted prior logic that
determined whether an ABTS was to be issued on the FC link.
Revert this logic to its proper state.
Link: https://lore.kernel.org/r/20210528212240.11387-1-jsmart2021@gmail.com
Fixes: db7531d2b3 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Cc: <stable@vger.kernel.org> # v5.11+
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce scsi_build_sense() as a wrapper around scsi_build_sense_buffer()
to format the buffer and set the correct SCSI status.
Link: https://lore.kernel.org/r/20210427083046.31620-8-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.10
Link: https://lore.kernel.org/r/20210514195559.119853-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-LS-5 specifies that a received RDF implies a possible change to fabric
supported diagnostic functions. Endpoints are to re-perform the RDF
exchange with the fabric to enable possible new features or adapt to
changes in values.
This patch adds the logic to RDF receive to re-perform the RDF exchange
with the switch.
Link: https://lore.kernel.org/r/20210514195559.119853-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior for the driver, when aborting an I/O, is to terminate the
I/O with the adapter. The adapter will initiate an ABTS to terminate the
exchange on the link and mark the exchange is terminated so that no further
use of the sgl or any traffic for the exchange is worked on. Completion on
the Abort is then posted to the driver, which as the I/O is terminated can
complete the I/O to the OS. This completion may occur prior to the ABTS
handshake completing on the wire. The ABTS handshake can take a long time
to complete with timeouts and retries reaching 60+ seconds. Note: if
retries fail, LOGO occurs.
Some devices want to ensure that the ABTS handshake fully completes (this
device has fully ack'd it) before the I/O completion is posted back to the
OS, where a failed I/O may be retried via a different path.
To support this behavior, an option was added to the driver to change I/O
completion from the Abort cmd completion to the Exchange termination (aka
ABTS) completion.
Link: https://lore.kernel.org/r/20210514195559.119853-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is encountering a crash in lpfc_free_iocb_list() while
performing initial attachment.
Code review found this to be an errant failure path that was taken, jumping
to a tag that then referenced structures that were uninitialized.
Fix the failure path.
Link: https://lore.kernel.org/r/20210514195559.119853-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a link bounce happens, there is a possibility that responses to
requests posted prior to the link bounce could be received. This is
problematic as the counter to track reglogin completion after link up can
become out of sync with the real state.
As there is no reason to process a request made in a prior link up context,
eliminate all the disturbance by tagging the request with the event_tag
maintained by the SLI Port for the link. The event_tag will change on every
link state transition. As long as the tag matches the current event_tag,
the response can be processed. If it doesn't match, just discard the
response.
Link: https://lore.kernel.org/r/20210514195559.119853-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link bounce testing, RPI counts were seen to differ from the number
of nodes. For fabric and domain controllers, a temporary RPI is assigned,
but the code isn't registering it. If the nodes do go away, such as on link
down, the temporary RPI isn't being released.
Change the way these two fabric services are managed, make them behave like
any other remote port. Register the RPI and register with the transport.
Never leave the nodes in a NPR or UNUSED state where their RPI is in limbo.
This allows them to follow normal dev_loss_tmo handling, RPI refcounting,
and normal removal rules. It also allows fabric I/Os to use the RPI for
traffic requests.
Note: There is some logic that still has a couple of exceptions when the
Domain controller (0xfffcXX). There are cases where the fabric won't have a
valid login but will send RDP. Other times, it will it send a LOGO then an
RDP. It makes for ad-hoc behavior to manage the node. Exceptions are
documented in the code.
Link: https://lore.kernel.org/r/20210514195559.119853-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc is handling a solicited and unsolicited PLOGI with another
initiator, the remote initiator is never recovered. The node for the
initiator is erroneouosly removed and all resources released.
In lpfc_cmpl_els_plogi(), when lpfc_els_retry() returns a failure code, the
driver is calling the state machine with a device remove event because the
remote port is not currently registered with the SCSI or NVMe
transports. The issue is that on a PLOGI "collision" the driver correctly
aborts the solicited PLOGI and allows the unsolicited PLOGI to complete the
process, but this process is interrupted with a device_rm event.
Introduce logic in the PLOGI completion to capture the PLOGI collision
event and jump out of the routine. This will avoid removal of the node.
If there is no collision, the normal node removal will occur.
Fixes: 52edb2caf6 ("scsi: lpfc: Remove ndlp when a PLOGI/ADISC/PRLI/REG_RPI ultimately fails")
Cc: <stable@vger.kernel.org> # v5.11+
Link: https://lore.kernel.org/r/20210514195559.119853-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is crashing due to a bad pointer during driver load due in an
adisc acc receive routine. The driver is missing node get/put in the
mbx_resume_rpi paths.
Fix by adding the proper gets and puts into the resume_rpi path.
Link: https://lore.kernel.org/r/20210514195559.119853-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An 'unexpected timeout' message may be seen in a point-2-point topology.
The message occurs when a PLOGI is received before the driver is notified
of FLOGI completion. The FLOGI completion failure causes discovery to be
triggered for a second time. The discovery timer is restarted but no new
discovery activity is initiated, thus the timeout message eventually
appears.
In point-2-point, when discovery has progressed before the FLOGI completion
is processed, it is not a failure. Add code to FLOGI completion to detect
that discovery has progressed and exit the FLOGI handling (noop'ing it).
Link: https://lore.kernel.org/r/20210514195559.119853-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When processing an NVMe ERSP IU which didn't match the optimized CQE-only
path, the status was being left to the WQE status. WQE status is non-zero
as it is indicating a non-optimized completion that needs to be handled by
the driver.
Fix by clearing the status field when falling into the non-optimized
case. Log message added to track optimized vs non-optimized debug.
Link: https://lore.kernel.org/r/20210514195559.119853-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing NPIV and watching logins and used RPI levels, it was seen the
used RPI count was much higher than the number of remote ports discovered.
Code inspection showed that remote port removals on any NPIV instance are
releasing the RPI, but not performing an UNREG_RPI with the adapter thus
the reference counting never fully drops and the RPI is never fully
released. This was happening on NPIV nodes due to a log of fabric ELS's to
fabric addresses. This lack of UNREG_RPI was introduced by a prior node
rework patch that performed the UNREG_RPI as part of node cleanup.
To resolve the issue, do the following:
- Restore the RPI release code, but move the location to so that it is in
line with the new node cleanup design.
- NPIV ports now release the RPI and drop the node when the caller sets
the NLP_RELEASE_RPI flag.
- Set the NLP_RELEASE_RPI flag in node cleanup which will trigger a
release of RPI to free pool.
- Ensure there's an UNREG_RPI at LOGO completion so that RPI release is
completed.
- Stop offline_prep from skipping nodes that are UNUSED. The RPI may
not have been released.
- Stop the default RPI handling in lpfc_cmpl_els_rsp() for SLI4.
- Fixed up debugfs RPI displays for better debugging.
Fixes: a70e63eee1 ("scsi: lpfc: Fix NPIV Fabric Node reference counting")
Link: https://lore.kernel.org/r/20210514195559.119853-2-jsmart2021@gmail.com
Cc: <stable@vger.kernel.org> # v5.11+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 312c004d36 ("[PATCH] driver core: replace "hotplug" by
"uevent"") already in the tree over a decade, update the name of
FW_ACTION defines to follow semantics, and reflect what the defines are
really meant for, i.e. whether or not generate user space event.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210425020024.28057-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer tmp_hdr is being assigned a value that is never read, the
assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210420104123.376420-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dump command for reading a region passes a requested read length
specified in words (4-byte units). The response overwrites the same field
with the actual number of bytes read.
The mailbox handler for DUMP which reads VPD data (region 23) is treating
the response field as if it were still a word_cnt, thus multiplying it by 4
to set the read's "length". Given the read value was calculated based on
the size of the read buffer, the longer response length runs off the end of
the buffer.
Fix by reworking the code to use the response field as a byte count.
Link: https://lore.kernel.org/r/20210421234511.102206-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_bsg_ct_unsol_event() routine acts assigns a ct_request to the wrong
structure address, resulting in a bad address that results in bsg related
timeouts.
Correct the ct_request assignment to use the kernel virtual buffer address
(not the control structure address).
Link: https://lore.kernel.org/r/20210421234448.102132-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In devloss timer handler and in backend calls to terminate remote port I/O,
there is logic to walk through all active IOCBs and validate them to
potentially trigger an abort request. This logic is causing illegal memory
accesses which leads to a crash. Abort IOCBs, which may be on the list, do
not have an associated lpfc_io_buf struct. The driver is trying to map an
lpfc_io_buf struct on the IOCB and which results in a bogus address thus
the issue.
Fix by skipping over ABORT IOCBs (CLOSE IOCBs are ABORTS that don't send
ABTS) in the IOCB scan logic.
Link: https://lore.kernel.org/r/20210421234433.102079-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2021 for files modified in the 12.8.0.9 patch set.
Link: https://lore.kernel.org/r/20210412013127.2387-17-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.9
Link: https://lore.kernel.org/r/20210412013127.2387-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code inspection, several cases of creating a dynamic attribute names
in logs messages using a define was found. This is unnecessary.
Place the native symbol name in the log messages.
Link: https://lore.kernel.org/r/20210412013127.2387-15-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code inspection showed lpfc was using three different pointer formats when
logging discovery object pointers.
Standardize the pointer format to x%px.
Note: %px use is limited to discovery objects in order to aid core
analysis.
Link: https://lore.kernel.org/r/20210412013127.2387-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up minor issues spotted by tools and code review:
- Spelling Errors
- Spurious characters and errors in function headers
- nvme_info wqerr and err fields source data reversed
- Extraneous new line in log message 0466
- Spacing error in log message 0109
- Messages 0140 and 0141 have portname and nodename reversed
- Incorrect function labelling in comment
Link: https://lore.kernel.org/r/20210412013127.2387-13-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI-4 does not contain a PORT_CAPABILITIES mailbox command (only SLI-3
does, and SLI-3 doesn't use it), yet there are SLI-4 code paths that have
code to issue the command. The command will always fail.
Remove the code for the mailbox command and leave only the resulting
"failure path" logic.
Link: https://lore.kernel.org/r/20210412013127.2387-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_hdw_queue attribute is to set the number of hardware queues to be
created on the adapter. Normally, the value is set to a default, which
allows the hw queue count to be sized dynamically based on adapter
capabilities, CPU/platform architecture, or CPU type. Currently, when
lpfc_hdw_queue is set to a specific value, is has no effect and the dynamic
sizing occurs.
The routine checking whether parameters are default or not ignores the
lpfc_hdw_queue setting and invokes the dynamic logic.
Fix the routine to additionally check the lpfc_hdw_queue attribute value
before using dynamic scaling. Additionally, SLI-3 supports only a small
number of queues with dedicated functions, thus it needs to be exempted
from the variable scaling and set to the expected values.
Link: https://lore.kernel.org/r/20210412013127.2387-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI registration needs to be performed after every login with the FC Mgmt
service. The flag the driver is using to track registration is cleared on
link up, but never on Mgmt service logout/re-login.
Fix by clearing the flag whenever a new login is completed with the FC Mgmt
service.
While perusing the flag use, logging was performed as if FDMI registration
occurred on vports. However, it is limited to the physical port only.
Revise the logging to reflect physical port based.
Link: https://lore.kernel.org/r/20210412013127.2387-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the unlikely case of a failure to allocate an LPFC_MBOXQ_t structure, no
return status is set, thus the routine never logs an error and returns
success to the callee.
Fix by setting a return code on failure.
Link: https://lore.kernel.org/r/20210412013127.2387-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During target port swap, the swap logic ignores the DROPPED flag in the
nodes. As a node then moves into the UNUSED state, the reference count will
be dropped. If a node is later reused and moved out of the UNUSED state, an
access can result in a use-after-free assert.
Fix by having the port swap logic propagate the DROPPED flag when switching
nodes. This will avoid reference from being dropped.
Link: https://lore.kernel.org/r/20210412013127.2387-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In SLI-4, when performing a mailbox command with MBX_POLL, the driver uses
the BMBX register to send the command rather than the MQ. A flag is set
indicating the BMBX register is active and saves the mailbox job struct
(mboxq) in the mbox_active element of the adapter. The routine then waits
for completion or timeout. The mailbox job struct is not freed by the
routine. In cases of timeout, the adapter will be reset. The
lpfc_sli_mbox_sys_flush() routine will clean up the mbox in preparation for
the reset. It clears the BMBX active flag and marks the job structure as
MBX_NOT_FINISHED. But, it never frees the mboxq job structure. Expectation
in both normal completion and timeout cases is that the issuer of the mbx
command will free the structure. Unfortunately, not all calling paths are
freeing the memory in cases of error.
All calling paths were looked at and updated, if missing, to free the mboxq
memory regardless of completion status.
Link: https://lore.kernel.org/r/20210412013127.2387-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During target port-swap testing with link flips, the initiator could
encounter PRLI errors. If the target node disappears permanently, the ndlp
is found stuck in UNUSED state with ref count of 1. The rmmod of the driver
will hang waiting for this node to be freed.
While handling a link error in PRLI completion path, the code intends to
skip triggering the discovery state machine. However this is causing the
final reference release path to be skipped. This causes the node to be
stuck with ref count of 1
Fix by ensuring the code path triggers the device removal event on the node
state machine.
Link: https://lore.kernel.org/r/20210412013127.2387-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove hbalock dependency for lpfc_abts_els_sgl_list and
lpfc_abts_nvmet_ctx_list. The lists are adaquately synchronized with the
sgl_list_lock and abts_nvmet_buf_list_lock.
Link: https://lore.kernel.org/r/20210412013127.2387-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call traces are being seen that result from a nodelist structure ref
counting error. They are typically seen after transmission of an LS_RJT ELS
response.
Aged code in lpfc_cmpl_els_rsp() calls lpfc_nlp_not_used() which, if the
ndlp reference count is exactly 1, will decrement the reference count.
Previously lpfc_nlp_put() was within lpfc_els_free_iocb(), and the 'put'
within the free would only be invoked if cmdiocb->context1 was not NULL.
Since the nodelist structure reference count is decremented when exiting
lpfc_cmpl_els_rsp() the lpfc_nlp_not_used() calls are no longer required.
Calling them is causing the reference count issue.
Fix by removing the lpfc_nlp_not_used() calls.
Link: https://lore.kernel.org/r/20210412013127.2387-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rmmod on SLI-4 adapters is sometimes hitting a bad ptr dereference in
lpfc_els_free_iocb().
A prior patch refactored the lpfc_sli_abort_iocb() routine. One of the
changes was to convert from building/sending an abort within the routine to
using a common routine. The reworked routine passes, without modification,
the pring ptr to the new common routine. The older routine had logic to
check SLI-3 vs SLI-4 and adapt the pring ptr if necessary as callers were
passing SLI-3 pointers even when not on an SLI-4 adapter. The new routine
is missing this check and adapt, so the SLI-3 ring pointers are being used
in SLI-4 paths.
Fix by cleaning up the calling routines. In review, there is no need to
pass the ring ptr argument to abort_iocb at all. The routine can look at
the adapter type itself and reference the proper ring.
Link: https://lore.kernel.org/r/20210412013127.2387-2-jsmart2021@gmail.com
Fixes: db7531d2b3 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Cc: <stable@vger.kernel.org> # v5.11+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-11 warns about an strnlen with a length larger than the size of the
passed buffer:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_nvme_info_show':
drivers/scsi/lpfc/lpfc_attr.c:518:25: error: 'strnlen' specified bound 4095 exceeds source size 24 [-Werror=stringop-overread]
518 | strnlen(LPFC_NVME_INFO_MORE_STR, PAGE_SIZE - 1)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this case, the code is entirely valid, as the string is properly
terminated, and the size argument is only there out of extra caution in
case it exceeds a page.
This cannot really happen here, so just simplify it to a sizeof().
Link: https://lore.kernel.org/r/20210322160253.4032422-10-arnd@kernel.org
Fixes: afff0d2321 ("scsi: lpfc: Add Buffer overflow check, when nvme_info larger than PAGE_SIZE")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If copy_from_user() or kstrtoull() fail then the correct behavior is to
return a negative error code.
Link: https://lore.kernel.org/r/YEsbU/UxYypVrC7/@mwanda
Fixes: f9bb2da11d ("[SCSI] lpfc 8.3.27: T10 additions for SLI4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:2021: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
Link: https://lore.kernel.org/r/20210312094738.2207817-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_bsg.c:3591: warning: expecting prototype for lpfc_bsg_mbox_ext_cleanup(). Prototype was for lpfc_bsg_mbox_ext_session_reset() instead
drivers/scsi/lpfc/lpfc_bsg.c:3885: warning: expecting prototype for lpfc_bsg_sli_cfg_mse_read_cmd_ext(). Prototype was for lpfc_bsg_sli_cfg_read_cmd_ext() instead
drivers/scsi/lpfc/lpfc_bsg.c:4371: warning: expecting prototype for lpfc_bsg_mbox_ext_abort_req(). Prototype was for lpfc_bsg_mbox_ext_abort() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-14-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_debugfs.c:405: warning: expecting prototype for lpfc_debugfs_common_xri_data(). Prototype was for lpfc_debugfs_commonxripools_data() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_attr.c:880: warning: expecting prototype for lpfc_state_show(). Prototype was for lpfc_link_state_show() instead
drivers/scsi/lpfc/lpfc_attr.c:3834: warning: expecting prototype for lpfc_tgt_queue_depth_store(). Prototype was for lpfc_tgt_queue_depth_set() instead
drivers/scsi/lpfc/lpfc_attr.c:4027: warning: expecting prototype for lpfc_topology_set(). Prototype was for lpfc_topology_store() instead
drivers/scsi/lpfc/lpfc_attr.c:4481: warning: expecting prototype for lpfc_link_speed_set(). Prototype was for lpfc_link_speed_store() instead
drivers/scsi/lpfc/lpfc_attr.c:4879: warning: expecting prototype for lpfc_request_firmware_store(). Prototype was for lpfc_request_firmware_upgrade_store() instead
drivers/scsi/lpfc/lpfc_attr.c:5235: warning: expecting prototype for lpfc_state_show(). Prototype was for lpfc_fcp_cpu_map_show() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-5-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_scsi.c:746: warning: expecting prototype for lpfc_release_scsi_buf(). Prototype was for lpfc_release_scsi_buf_s3() instead
drivers/scsi/lpfc/lpfc_scsi.c:979: warning: expecting prototype for App checking is required for(). Prototype was for BG_ERR_CHECK() instead
drivers/scsi/lpfc/lpfc_scsi.c:3701: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf'
drivers/scsi/lpfc/lpfc_scsi.c:3701: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf'
drivers/scsi/lpfc/lpfc_scsi.c:3717: warning: Function parameter or member 'fcpi_parm' not described in 'lpfc_send_scsi_error_event'
drivers/scsi/lpfc/lpfc_scsi.c:3717: warning: Excess function parameter 'rsp_iocb' description in 'lpfc_send_scsi_error_event'
drivers/scsi/lpfc/lpfc_scsi.c:3837: warning: Function parameter or member 'fcpi_parm' not described in 'lpfc_handle_fcp_err'
drivers/scsi/lpfc/lpfc_scsi.c:3837: warning: expecting prototype for lpfc_handler_fcp_err(). Prototype was for lpfc_handle_fcp_err() instead
drivers/scsi/lpfc/lpfc_scsi.c:4021: warning: Function parameter or member 'wcqe' not described in 'lpfc_fcp_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_scsi.c:4021: warning: Excess function parameter 'pwqeOut' description in 'lpfc_fcp_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_scsi.c:4621: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:4621: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:4698: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:4698: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:4954: warning: expecting prototype for lpfc_taskmgmt_def_cmpl(). Prototype was for lpfc_tskmgmt_def_cmpl() instead
drivers/scsi/lpfc/lpfc_scsi.c:5094: warning: expecting prototype for lpfc_poll_rearm_time(). Prototype was for lpfc_poll_rearm_timer() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-4-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_hbadisc.c:1505: warning: expecting prototype for lpfc_update_fcf_record(). Prototype was for __lpfc_update_fcf_record() instead
Link: https://lore.kernel.org/r/20210303144631.3175331-28-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'ct_req' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'rx_id' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'ox_id' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:283: warning: Function parameter or member 'ctiocbq' not described in 'lpfc_ct_handle_mibreq'
drivers/scsi/lpfc/lpfc_ct.c:283: warning: Excess function parameter 'ctiocb' description in 'lpfc_ct_handle_mibreq'
Link: https://lore.kernel.org/r/20210303144631.3175331-26-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c:9654: warning: expecting prototype for lpfc_sli_iocb2wqe(). Prototype was for lpfc_sli4_iocb2wqe() instead
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'phba' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'piocb' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'flag' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:14189: warning: expecting prototype for lpfc_sli4_sp_process_cq(). Prototype was for __lpfc_sli4_sp_process_cq() instead
drivers/scsi/lpfc/lpfc_sli.c:14754: warning: expecting prototype for lpfc_sli4_hba_process_cq(). Prototype was for lpfc_sli4_dly_hba_process_cq() instead
drivers/scsi/lpfc/lpfc_sli.c:17230: warning: expecting prototype for lpfc_sli4_free_xri(). Prototype was for __lpfc_sli4_free_xri() instead
drivers/scsi/lpfc/lpfc_sli.c:18950: warning: expecting prototype for lpfc_sli4_free_rpi(). Prototype was for __lpfc_sli4_free_rpi() instead
Link: https://lore.kernel.org/r/20210303144631.3175331-18-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the files modified in 2021 via the 12.8.0.7 and 12.8.0.8 patch sets,
update the copyright for 2021.
Link: https://lore.kernel.org/r/20210301171821.3427-23-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.8.
Link: https://lore.kernel.org/r/20210301171821.3427-22-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code inspection revealed stale comments in function headers for functions
that call lpfc_prep_els_iocb(). Changes in ndlp reference counting were not
reflected in function headers.
Update the stale comments in function headers to more accurately indicate
ndlp reference counting.
Link: https://lore.kernel.org/r/20210301171821.3427-21-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lots of discovery messages are flooding the console log when testing NPIV.
Informational message for vports should have LOG_VPORT associated with it
as opposed to LOG_TRACE_EVENT.
Link: https://lore.kernel.org/r/20210301171821.3427-20-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message 8347 Invalid device found log message is logged when an LPe12000
adapter is installed. The log message is supposed to indicate an
unsupported pci reset adapter rather than an invalid device.
Change the wording to: Incapable PCI reset device.
Link: https://lore.kernel.org/r/20210301171821.3427-19-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is causing a crash in __lpfc_sli_release_iocbq_s4() when it
dereferences the els_wq which is NULL.
Validate the pring for the els_wq before dereferencing. Reorg the code to
move the pring assignment closer to where it is actually used.
Link: https://lore.kernel.org/r/20210301171821.3427-18-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a setup with a dual port HBA and both ports direct connected, an rmmod
hangs momentarily when we log an Illegal State Transition. Once it resumes,
a nodelist not empty logic is hit, which forces rmmod to cleanup and exit.
We're missing a state transition case in the discovery engine.
Fix by adding a case for a DEVICE_RM event while in the unmapped state to
avoid illegal state transition log message.
Link: https://lore.kernel.org/r/20210301171821.3427-17-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debugfs nodeinfo output gets jumbled when no rpri or a defer entry is
displayed. The misalignment makes it difficult to read.
Change the format to consistently print out a 4 character rpi, and turn
defer into a suffix.
Link: https://lore.kernel.org/r/20210301171821.3427-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing target port swap test with ADISC enabled, several nodes
remain in UNUSED state. These nodes are never freed and rmmod hangs for
long time before finising with "0233 Nodelist not empty" error.
During PLOGI completion lpfc_plogi_confirm_nport() looks for existing nodes
with same WWPN. If found, the existing node is used to continue discovery.
The node on which plogi was performed is freed. When ADISC is enabled, an
ADISC els request is triggered in response to an RSCN. It's possible that
the ADISC may be rejected by the remote port causing the ADISC completion
handler to clear the port and node name in the node. If this occurs, if a
PLOGI is received it causes a node lookup based on wwpn to now fail,
causing the port swap logic to kick in which allocates a new node and swaps
to it. This effectively orphans the original node structure.
Fix the situation by detecting when the lookup fails and forgo the node
swap and node allocation by using the node on which the PLOGI was issued.
Link: https://lore.kernel.org/r/20210301171821.3427-15-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is seeing a scenario where PLOGI response was issued and traffic
is arriving while the adapter is still setting up the login context. This
is resulting in errors handling the traffic.
Change the driver so that PLOGI response is sent after the login context
has been setup to avoid the situation.
Link: https://lore.kernel.org/r/20210301171821.3427-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected in pt2pt mode, there is a scenario where the remote port
significantly delays sending a response to our FLOGI, but acts on the FLOGI
it sent us and proceeds to PLOGI/PRLI. The FLOGI ends up timing out and
kicks off recovery logic. End result is a lot of unnecessary state changes
and lots of discovery messages being logged.
Fix by terminating the FLOGI and noop'ing its completion if we have already
accepted the remote ports FLOGI and are now processing PLOGI.
Link: https://lore.kernel.org/r/20210301171821.3427-13-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An unlikely error exit path from lpfc_els_retry() returns incorrect status
to a caller, erroneously indicating that a retry has been successfully
issued or scheduled.
Change error exit path to indicate no retry.
Link: https://lore.kernel.org/r/20210301171821.3427-12-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several code paths where the following sequence occurs:
- An ndlp pointer is assigned to an iocb via a nlp_get()
- An attempt is made to issue the iocb, but it fails
- The failure case does a put on the ndlp then calls lpfc_els_free_iocb()
The put may free the ndlp structure, but the els_free_iocb may reference
the now-stale ndlp pointer and cause a crash.
Fix by ensuring that the lpfc_els_free_iocb() occurs before the
lpfc_nlp_put().
While fixing, refactor the code to better ensure this calling sequence.
Link: https://lore.kernel.org/r/20210301171821.3427-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible to call lpfc_issue_els_plogi() passing a did for which no
matching ndlp is found. A call is then made to lpfc_prep_els_iocb() with a
null pointer to a lpfc_nodelist structure resulting in a null pointer
dereference.
Fix by returning an error status if no valid ndlp is found. Fix up comments
regarding ndlp reference counting.
Link: https://lore.kernel.org/r/20210301171821.3427-10-jsmart2021@gmail.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_fcp_io_cmd_wqe_cmpl() is intended to mirror
lpfc_nvme_io_cmd_wqe_cmpl() for sli4 fcp completions. When the routine was
added, lpfc_fcp_io_cmd_wqe_cmpl() included a null pointer check for
phba. However, phba is definitely valid, being dereferenced by the calling
routine and used later in the routine itself.
Remove the unnecessary null check.
Link: https://lore.kernel.org/r/20210301171821.3427-9-jsmart2021@gmail.com
Fixes: 96e209be6e ("scsi: lpfc: Convert SCSI I/O completions to SLI-3 and SLI-4 handlers")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a pt2pt setup, between 2 initiators, if one side issues a a LOGO, there
is no relogin attempt. The FC specs are grey in this area on which port
(higher wwn or not) is to re-login.
As there is no spec guidance, unconditionally re-PLOGI after the logout to
ensure a login is re-established.
Link: https://lore.kernel.org/r/20210301171821.3427-8-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver crashed in lpfc_debugfs_disc_trc() due to null ndlp pointer. In
some calling cases, the ndlp is null and the did is looked up.
Fix by using the local did variable that is set appropriately based on ndlp
value.
Link: https://lore.kernel.org/r/20210301171821.3427-7-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After an initial successful FLOGI into the switch, if a subsequent FLOGI
fails the driver crashed accessing a node struct. On FLOGI error, the flogi
completion logic triggers the final dereference on the node structure
without checking if it is registered with a backend. The devloss logic is
triggered after node is freed leading to the access of freed node.
Fix by adjusting the error path to not take the final dereferece if there
is an outstanding transport registration. Let the transport devloss call
remove the final reference.
Link: https://lore.kernel.org/r/20210301171821.3427-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever an RRQ needs to be triggered, the DID from the node structure and
node pointer are stored in the RRQ data structure and the RRQ is scheduled
for later transmission. However, at the point in time that the timer
triggers, there's no validation on the node pointer. Reference counters may
have freed the structure. Additionally the DID in the node may no longer be
valid.
Fix by not tracking the node pointer in the RRQ, only the DID. At the time
of the timer expiration, look up the node with the did and if present, send
the RRQ. If no node exists, no need to send the RRQ.
Link: https://lore.kernel.org/r/20210301171821.3427-5-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An LBA is 8 bytes. The driver generates a reftag from the LBA but the
reftag is 4 bytes. Thus scsi_get_lba() could return a value that exceeds
our reftag size.
Fix by converting all the code to calling the common routine
t10_pi_ref_tag() which returns a u32, thus ensuring a consistent 4byte
value. Also correct a few code lines that access LBA directly and ensure
64-bit data types are used.
Link: https://lore.kernel.org/r/20210301171821.3427-4-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calls to lpfc_find_vport_by_vpid() for the highest indexed vport fails with
error, "2936 Could not find Vport mapped to vpi XXX". Our vport indices in
the loop and if-clauses were off by one.
Correct the vpid range used for vpi lookup to include the highest possible
vpid.
Link: https://lore.kernel.org/r/20210301171821.3427-3-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The wqe_dbde field indicates whether a Data BDE is present in Words 0:2 and
should therefore should be clear in the abts request wqe. By setting the
bit we can be misleading fw into error cases.
Clear the wqe_dbde field.
Link: https://lore.kernel.org/r/20210301171821.3427-2-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere). The
only big major rework of note is the one from Hannes trying to clean
up our result handling code in the drivers to make it consistent.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYDAdliYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTblAQCk6wD8
fcb4TItSRp0DpRzs37zhppEbrBgveuAFHhr5swEA0gL2mHcq0vnyNBinCLnERrE7
TPYJqUKJNktnjVG7ZWc=
=wW6p
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere).
The only big major rework of note is the one from Hannes trying to
clean up our result handling code in the drivers to make it
consistent"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (194 commits)
scsi: MAINTAINERS: Adjust to reflect gdth scsi driver removal
scsi: ufs: Give clk scaling min gear a value
scsi: lpfc: Fix 'physical' typos
scsi: megaraid_mbox: Fix spelling of 'allocated'
scsi: qla2xxx: Simplify the calculation of variables
scsi: message: fusion: Fix 'physical' typos
scsi: target: core: Change ASCQ for residual write
scsi: target: core: Signal WRITE residuals
scsi: target: core: Set residuals for 4Kn devices
scsi: hisi_sas: Add trace FIFO debugfs support
scsi: hisi_sas: Flush workqueue in hisi_sas_v3_remove()
scsi: hisi_sas: Enable debugfs support by default
scsi: hisi_sas: Don't check .nr_hw_queues in hisi_sas_task_prep()
scsi: hisi_sas: Remove deferred probe check in hisi_sas_v2_probe()
scsi: lpfc: Add auto select on IRQ_POLL
scsi: ncr53c8xx: Fix typos
scsi: lpfc: Fix ancient double free
scsi: qla2xxx: Fix some memory corruption
scsi: qla2xxx: Remove redundant NULL check
scsi: megaraid: Fix ifnullfree.cocci warnings
...
In testing, in a configuration with Redfish and native NVMe multipath when
an EEH is injected, a kernel oops is being encountered:
(unreliable)
lpfc_nvme_ls_req+0x328/0x720 [lpfc]
__nvme_fc_send_ls_req.constprop.13+0x1d8/0x3d0 [nvme_fc]
nvme_fc_create_association+0x224/0xd10 [nvme_fc]
nvme_fc_reset_ctrl_work+0x110/0x154 [nvme_fc]
process_one_work+0x304/0x5d
the NBMe transport is issuing a Disconnect LS request, which the driver
receives and tries to post but the work queue used by the driver is already
being torn down by the eeh.
Fix by validating the validity of the work queue before proceeding with the
LS transmit.
Link: https://lore.kernel.org/r/20210127221601.84878-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "pmb" pointer is freed at the start of the function and then freed
again in the error handling code.
Link: https://lore.kernel.org/r/YA6E8rO51hE56SVw@mwanda
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for eh_should_retry_cmd callback in lpfc_template.
Link: https://lore.kernel.org/r/1609969748-17684-6-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
./drivers/scsi/lpfc/lpfc_bsg.c:5392:5-29: WARNING: Comparison to bool
Link: https://lore.kernel.org/r/1610439893-64872-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.7
Link: https://lore.kernel.org/r/20210104180240.46824-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing recent discovery node rework, several items were seen that
could be done better with respect to the new trace event logic.
1) in the following msg:
kernel: lpfc 0000:44:00.0: start 35 end 35 cnt 0
If cnt is zero in the 1st message, there is no reason to display the
1st message, which is just giving start/end positioning.
Fix by not displaying message if cnt is 0.
2) If the driver is loaded with module log verbosity off, and later a
single NPIV host instance verbosity is enabled via sysfs, it enables
messages on all instances. This is due to the trace log verbosity checks
(lpfc_dmp_dbg) looking at the phba only. It should look at the phba and
the vport.
Fix by enabling a check on both phba and vport.
3) in the following messages:
2904 Firmware Dump Image Present on Adapter
2887 Reset Needed: Attempting Port Recovery...
These messages are not necessary for the trace event log, which is
primarily for discovery.
Fix by changing log level on these 2 messages to LOG_SLI.
Link: https://lore.kernel.org/r/20210104180240.46824-15-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several errors have occurred where the adapter stops or fails but does not
raise the register values for the driver to detect failure. Thus driver is
unaware of the failure. The failure typically results in I/O timeouts, the
I/O timeout handler failing (after several seconds), and the error handler
escalating recovery policy and resulting in more errors. Eventually, the
driver is in a position where things have spiraled and it can't do recovery
because other recovery ops are still outstanding and it becomes unusable.
Resolve the situation by having the I/O timeout handler (actually a els,
SCSI I/O, NVMe ls, or NVMe I/O timeout), in addition to aborting the I/O,
perform a mailbox command and look for a response from the hardware. If
the mailbox command fails, it will mark the adapter offline and then invoke
the adapter reset handler to clean up.
The new I/O timeout test will be limited to a test every 5s. If there are
multiple I/O timeouts concurrently, only the 1st I/O timeout will generate
the mailbox command. Further testing will only occur once a timeout occurs
after a 5s delay from the last mailbox command has expired.
Link: https://lore.kernel.org/r/20210104180240.46824-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc is running in NVMET mode and supports the NVME-1 addendum
changes, a LIP on a bound NVME Initiator or lipping the lpfc NVMET's link
resulted in an Oops in lpfc_nvmet_host_release.
The fix requires lpfc NVMET to maintain an additional reference on any node
structure that acts as the hosthandle for the NVMET transport. This
reference get is a one-time addition, is taken prior to the upcall of an
unsolicited LS_REQ, and is released when the NVMET transport releases the
hosthandle during the host_release downcall.
Link: https://lore.kernel.org/r/20210104180240.46824-13-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When with testing with large numbers of npiv vports and link bounces, the
driver is flooding the messages file, even with log_verbose = 0.
The new LOG_TRACE_EVENT messages are still generating events to the
messages files.
Fix by converting the vport create msg from LOG_TRACE_EVENT to LOG_VPORT.
Link: https://lore.kernel.org/r/20210104180240.46824-12-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a mailbox command times out, the SLI port is deemed in error and the
port is reset. The HBA cleanup is not returning I/Os to the NVMe layer
before the port is unregistered. This is due to the HBA being marked
offline (!SLI_ACTIVE) and cleanup being done by the mailbox timeout handler
rather than an general adapter reset routine. The mailbox timeout handler
mailbox handler only cleaned up SCSI I/Os.
Fix by reworking the mailbox handler to:
- After handling the mailbox error, detect the board is already in
failure (may be due to another error), and leave cleanup to the
other handler.
- If the mailbox command timeout is initial detector of the port error,
continue with the board cleanup and marking the adapter offline
(!SLI_ACTIVE). Remove the SCSI-only I/O cleanup routine. The generic
reset adapter routine that is subsequently invoked, will clean up the
I/Os.
- Have the reset adapter routine flush all NVMe and SCSI I/Os if the
adapter has been marked failed (!SLI_ACTIVE).
- Rework the NVMe I/O terminate routine to take a status code to fail the
I/O with and update so that cleaned up I/O calls the wqe completion
routine. Currently it is bypassing the wqe cleanup and calling the NVMe
I/O completion directly. The wqe completion routine will take care of
data structure and node cleanup then call the NVMe I/O completion
handler.
Link: https://lore.kernel.org/r/20210104180240.46824-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Target reset is failed by the target as an invalid command.
The Target Reset TMF has been obsoleted in T10 for a while, but continues
to be used. On (newer) devices, the TMF is rejected causing the reset
handler to escalate to adapter resets.
Fix by having Target Reset TMF rejections be translated into a LOGO and
re-PLOGI with the target device. This provides the same semantic action
(although, if the device also supports nvme traffic, it will terminate nvme
traffic as well - but it's still recoverable).
Link: https://lore.kernel.org/r/20210104180240.46824-10-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A successful task mgmt command is logging errors, making it look like
problems were encountered. This is due to log messages for the
device/target and bus reset handlers having the LOG_TRACE_EVENT flag set.
Fix by adjusting the event flag such that the call to the logging routine
only receives a LOG_TRACE_EVENT if a prior call actually failed.
Link: https://lore.kernel.org/r/20210104180240.46824-9-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc offline routine, called for various reasons such as sysfs
attribute, driver unload, or port error, the driver is calling
__lpfc_cpuhp_remove() to destroy the hot plug data. If the offline routine
is called while the driver is in the process of being unloaded, a request
using lpfc_cpuhp_remove() is also made from lpfc_sli4_hba_unset(). The
cpuhp elements are no longer valid when the second removal request is made.
Fix by only calling the cpuhp removal once when the adapter is in the
process of unloading.
Link: https://lore.kernel.org/r/20210104180240.46824-8-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the port is configured for NVME and has any outstanding IOs when a FW
reset is requesteed, outstanding I/Os are not properly cleaned up. This
causes the fw download request to fail.
Fix by clearing the LPFC_SLI_ACTIVE flag to signify the I/O must be
manually flushed by the driver on port reset.
Link: https://lore.kernel.org/r/20210104180240.46824-7-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc generates a GEN_REQUEST wqe for the nvme LS (such as Create
Association), the timeout is set to R_A_TOV without regard to the timeout
value supplied by the nvme-fc transport. The driver should be setting the
timeout to the value passed into the routine. Additionally the caller
should be setting the timeout value to the value in the ls request set by
the nvme transport. Instead, it unconditionally is setting it to a driver
defined value. So the driver actually overrode the value twice.
Fix by using the timeout provided to the routine, and for the caller, set
the timeout to the ls request timeout value.
Link: https://lore.kernel.org/r/20210104180240.46824-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's management of the fabric controller (aka pseudo-scsi
initiator) node in SLI3 mode is causing this crash. The crash occurs
because of a node reference imbalance that frees the fabric controller node
while devloss is outstanding from the SCSI transport. This is triggered by
an odd behavior where the switch reacts to a rejected RDP request with a
PLOGI and nothing else, not even a LOGO. The driver ACKS the PLOGI and
after successfully registering the RPI, incorrectly registers the fabric
controller node because it has the NLP_FC4_FCP flag still set from the
fabric controller PRLI. If a LIP is issued, the driver attempts to cleanup
on Link Up and ends up executing too many puts.
Fix by detecting the fabric node type and clearing out the nodes internal
flags that triggered a SCSI transport registration and subsequence dev_loss
event. The driver cannot count on any persistence from fabric controller
nodes.
Link: https://lore.kernel.org/r/20210104180240.46824-5-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing with target ports coming and going, the driver eventually reached a
state where it no longer discovered the target. When the driver has issued
a PRLI and receives a PRLI from the target, it is not properly updating the
node's initiator/target role flags. Thus, when a subsequent RSCN is
received for a target loss, the driver mis-identifies the target as an
initiator and does not initiate LUN scanning.
Fix by always refreshing the ndlp with the latest PRLI state information
whenever a PRLI is processed. Also clear the ndlp flags when processing a
PLOGI so that there is no carry over through a re-login.
Link: https://lore.kernel.org/r/20210104180240.46824-4-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A very long time ago, there was a feature: auto sli mode. It gave the user
the ability to auto select the SLI mode (SLI2 or SLI3) to run the port in,
or even force SLI2 mode if configured. Because of the convoluted logic,
the CONFIG_PORT mbox command ends up being called 2 or 3 times. It should
have been called only once. Additionally, the driver no longer supports
SLI-2, so only SLI-3 mode should be allowed.
The following changes were made:
- Force module parameter to SLI3 only.
- Rip out redundant CONFIG_PORT mbox commands.
- Force CONFIG_PORT mbox command to be in beginning of enable ISR routine.
- Added changes for offline to online behavior
Link: https://lore.kernel.org/r/20210104180240.46824-3-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under some pt2pt situations, the other end of the link may issue a LOGO
after successfully completing PLOGI and assigning addresses to the port.
Thus the driver may attempt a new PLOGI to re-create the login, but the
LOGO handling cleared the address back to 0. Once this happens, the other
end, which may be address 0, gets all confused and this cannot be resolved
without an administrative action to bounce the link.
Fix by assuming that address assignment only occurs on the 1st PLOGI after
link up, and regardless of login state, the address assignment sticks. The
FC standards aren't particularly clear in this situation (it only describes
initial PLOGI), but there is nothing that contradicts this and behaviors on
the devices tested appears to conform to the understanding.
Thus, don't reset the port address to 0 as part of LOGO handling. Port
addresses will only reset on link down.
Link: https://lore.kernel.org/r/20210104180240.46824-2-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
smatch correctly called out a logic error with accessing a pointer after
checking it for null:
drivers/scsi/lpfc/lpfc_els.c:2043 lpfc_cmpl_els_plogi()
error: we previously assumed 'ndlp' could be null (see line 1942)
Adjust the exit point to avoid the trace printf ndlp reference. A trace
entry was already generated when the ndlp was checked for null.
Link: https://lore.kernel.org/r/20201130181226.16675-1-james.smart@broadcom.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Link: https://lore.kernel.org/r/20201102164730.324035-18-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove vport variable that is assigned but not used in
lpfc_sli4_abts_err_handler().
Link: https://lore.kernel.org/r/20201119203407.121913-1-james.smart@broadcom.com
Fixes: e7dab164a9 ("scsi: lpfc: Fix scheduling call while in softirq context in lpfc_unreg_rpi")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvmet_prep_abort_wqe() needs to be declared static.
Link: https://lore.kernel.org/r/20201119203316.121725-1-james.smart@broadcom.com
Fixes: db7531d2b3 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove set but not used variable shost in lpfc_dev_loss_tmo_handler().
Link: https://lore.kernel.org/r/20201119203353.121866-1-james.smart@broadcom.com
Fixes: 52edb2caf6 ("scsi: lpfc: Remove ndlp when a PLOGI/ADISC/PRLI/REG_RPI ultimately fails")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove local variables that are set but not used.
Link: https://lore.kernel.org/r/20201119203340.121819-1-james.smart@broadcom.com
Fixes: c6adba1501 ("scsi: lpfc: Rework remote port lock handling")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function needs to be declared as static.
Link: https://lore.kernel.org/r/20201119203328.121772-1-james.smart@broadcom.com
Fixes: 8aaa7bcf07 ("scsi: lpfc: Add FDMI Vendor MIB support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is an error return path that neglects to free the
allocation for lcb_context. Fix this by adding a new error free exit path
that kfree's lcb_context before returning. Use this new kfree exit path in
another exit error path that also kfree's the same object, allowing a line
of code to be removed.
Link: https://lore.kernel.org/r/20201118141314.462471-1-colin.king@canonical.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Resource leak")
Currently there is a null check on the pointer ndlp that exits via error
path issue_ct_rsp_exit followed by another null check on the same pointer
that is almost identical to the previous null check stanza and yet can
never can be reached because the previous check exited via
issue_ct_rsp_exit. This is deadcode and can be removed.
Link: https://lore.kernel.org/r/20201118133744.461385-1-colin.king@canonical.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Logically dead code")
There is a null check on pointer lpfc_cmd after the pointer has been
dereferenced when pointers rdata and ndlp are initialized at the start of
the function. Fix this by only assigning rdata and ndlp after the pointer
lpfc_cmd has been null checked.
Link: https://lore.kernel.org/r/20201118131345.460631-1-colin.king@canonical.com
Fixes: 96e209be6e ("scsi: lpfc: Convert SCSI I/O completions to SLI-3 and SLI-4 handlers")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Dereference before null check")
Update Copyright in files changed by the 12.8.0.6 patch set to 2020
Link: https://lore.kernel.org/r/20201115192646.12977-18-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.6
Link: https://lore.kernel.org/r/20201115192646.12977-17-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reworks the abort interfaces such that SLI-3 retains the
iocb-based formatting and completions and SLI-4 now uses native WQEs and
completion routines.
The following changes are made:
- The code is refactored from a confusing 2 routine sequence of
xx_abort_iotag_issue(), which creates/formats and abort cmd, and
xx_issue_abort_tag(), which then issues and handles the completion of
the abort cmd - into a single interface of xx_issue_abort_iotag(). The
new interface will determine whether SLI-3 or SLI-4 and then call the
appropriate handler. A completion handler can now be specified to
address the differences in completion handling. Note: original code is
all iocb based, with SLI-4 converting to SLI-3 for the SCSI/ELS path,
and NVMe natively using wqes.
- The SLI-3 side is refactored:
The older iocb-base lpfc_sli_issue_abort_iotag() routine is combined
with the logic of lpfc_sli_abort_iotag_issue() as well as the
iocb-specific code in lpfc_abort_handler() and lpfc_sli_abort_iocb() to
create the new single SLI-3 abort routine that formats and issues the
iocb.
- The SLI-4 side is refactored and added to:
The native WQE abort code in NVMe is moved to the new SLI-4
issue_abort_iotag() routine. Items in SCSI that set fields not set by
NVMe is migrated into the new routine. Thus the routine supports NVMe
and SCSI initiators. The nvmet block (target) formats the abort slightly
different (like the old NVMe initiator) thus it has its own prep routine
stolen from NVMe initiator and it retains the current code it has for
issuing the WQE (does not use the commonized routine the initiators
do). SLI-4 completion handlers were also added.
- lpfc_abort_handler now becomes a wrapper that determines whether
SLI-3 or SLI-4 and calls the proper abort handler.
Link: https://lore.kernel.org/r/20201115192646.12977-16-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver implementation uses SLI-4 WQE to iocb conversion before
calling the cmpl callback function.
Rework the FCP I/O completion path to utilize the SLI-4 WQE.
This patch converts the SCSI I/O completion paths from the iocb-centric
interfaces to the routines are native for whether I/Os are iocb-based
(SLI-3) or WQE-based (SLI-4).
Most existing routines were iocb-based, so this creates a lot of SLI-4
specific routines to provide the functionality.
Link: https://lore.kernel.org/r/20201115192646.12977-15-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch converts the SCSI I/O path from the iocb-centric interfaces to
the common I/O submission path which supports native SLI-4 WQEs.
A wrapper routine is put in place to distinguish SLI-3 from SLI. If SLI-3,
the same iocb-centric paths are used, perhaps with refactored code that is
explicitly for SLI-3. For SLI-4, any iocb-related formatting is replaced
by wqe-based formatting, although much of that is addressed by the common
wqe templates in the SLI-4 path.
Link: https://lore.kernel.org/r/20201115192646.12977-14-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To set up common use by the SCSI and NVMe I/O paths, create a new routine
that issues FCP I/O commands which can be used by either protocol. The new
routine addresses SLI-3 vs SLI-4 differences within its implementation.
Replace the (SLI-3 centric) iocb routine in the SCSI path with this new
WQE-centric common routine.
Link: https://lore.kernel.org/r/20201115192646.12977-13-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using SLI-4 WQE templates only for NVMe. Refactor
the template and the placement of the service routine so that it can be
used by both SCSI and NVMe.
Link: https://lore.kernel.org/r/20201115192646.12977-12-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation of reworking the driver to use a native SLI-4 WQE interface
for the SCSI and NVMe I/O paths, start by commonizing the WQE exchange type
and command type attributes.
While adjusting these options also noted the variance in the pbde field.
Fix this by setting templates to 0 and in NVMe, which explicitly uses this
option, setting the value.
Link: https://lore.kernel.org/r/20201115192646.12977-11-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing initiator-side cable swaps with NPIV, oops occur. The
reference counts for the Fabric nodes on the NPIV vports isn't balanced,
resulting in premature node removal.
The following fixes were made:
- Removed the FC_LBIT check in lpfc_linkup_port. This removed the special
case for vports that didn't have them clean up just like the physical
port.
- Removed the unreg_rpi call in lpfc_cleanup_node. In this section, the
node is being removed in the context of a reference count release and a
mailbox command can't be issued at this point.
- Remove special case handling in the default mailbox completion handler
that allowed the skipping of a node reference. Now, reference counting
always requires the removal of the reference.
- Move the location of the DEVICE_RM event is done during LOGO handling as
the driver has additional work to do on the ndlp before puts/releases
can be performed.
Link: https://lore.kernel.org/r/20201115192646.12977-10-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing NPIV and link bounces, the vport would not show a fabric node
for the F_Port, would not transition into NPR state during a link fault, or
leave the FDMI node untouched during error injection. Cause for this was
determined to be an inconsistent manner in which F_Port, Nameserver, and
FDMI controller nodes were created and linked. In some cases, the nodes
would never be unregistered from the transport, leaving references
active. In other cases, the fabric nodes may register with the transport
multiple times while still registered.
The following changes were made:
- Fix the FDISC issue routine, which starts vport (re)creation, to mark
the F_Port as a fabric node (NLP_FABRIC) and allow the F_Port node to
fully be created and show up in the node list.
- When remote ports are cleaned up on vport termination, cleanup the
nameserver and FDMI controller nodes on the vport so they unregister
from the transport.
- On link bounces, don't exclude the NPIV Fabric remote ports from
transitioning to the NPR state, allowing them to avoid re-registration
if already registered.
Link: https://lore.kernel.org/r/20201115192646.12977-9-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target swap happens, under certain conditions the node sends a
LOGO. The unsolicited ELS logic responds with a reject. The logic may
allocate a new node to handle this. Afterward, the new nodes are dropped
incorrectly leaving them in a mis-matched state and refcounting causes a
use-after-free situation leading to a crash.
It is also possible that the unsolicited els handling finds a node which is
in an UNUSED state. The handling moves these nodes to NPR state with a
refcount of 1. Although the end of the discovery logic assumes a final put
will free such a node, there are codes paths which could increment the
reference count, thus the node is in NPR state and not released.
Eventually this mismatch in state and refcount leads to premature release
of the node causing a crash.
Fix by always using the discovery engine DEVICE RM event to decrement and
release the nodes (rather than explicit code that tried to do it before).
This will take care of moving the node to the UNUSED state and then removes
the final ref count. If there is a trigger to reuse this node, the
transition from the UNUSED state clearly indicates that the initial
reference is then incremented and use can continue.
Link: https://lore.kernel.org/r/20201115192646.12977-8-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a PLOGI/ADISC/PRLI/REG_RPI fails, the node remains in the nodelist in
that state. Although the driver now frees a node when the ref count goes
to zero, in this case the ref cnt doesn't reach zero because there isn't a
mechanism to release the final reference. Discovery just stops.
Fix by calling the node discovery state machine DEVICE_RM event whenever
one of these commands fail. This will remove the final reference count and
trigger node release.
Link: https://lore.kernel.org/r/20201115192646.12977-7-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the discovery layers within the driver use the SCSI midlayer
host_lock to access node-specific structures. This can contend with the I/O
path and is too coarse of a lock.
Rework the driver so that it uses a lock specific to the remote port node
structure when accessing the structure contents. A few of the changes
brought out spots were some slightly reorganized routines worked better.
Link: https://lore.kernel.org/r/20201115192646.12977-6-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to bug history and code review, the node reference counting approach in
the driver isn't implemented consistently with how the scsi and nvme
transport perform registrations and unregistrations and their callbacks.
This resulted in many bad/stale node pointers.
Reword the driver so that reference handling is performed as follows:
- The initial node reference is taken on structure allocation
- Take a reference on any add/register call to the transport
- Remove a reference on any delete/unregister call to the transport
- After the node has fully removed from both the SCSI and NVMEe transports
(dev_loss_callbacks have called back) call the discovery engine
DEVICE_RM event which will remove the final reference and release the
node structure.
- Alter dev_loss handling when a vport or base port is unloading.
- Remove the put_node handling - no longer needed.
- Rewrite the vport_delete handling on reference counts. Part of this
effort was driven from the FDISC not registering with the transport and
disrupting the model for node reference counting.
- Deleted lpfc_nlp_remove. Pushed it's remaining ops into
lpfc_nlp_release.
- Several other small code cleanups.
Link: https://lore.kernel.org/r/20201115192646.12977-5-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc driver is calling get_device and put_device on scsi_fc_transport
device structure. When this code was removed, the driver triggered an oops
in "scsi_is_host_dev" when the first SCSI target was unregistered from the
transport.
The reason the calls were necessary is that the driver is calling
scsi_remove_host too early, before the target rports are unregistered and
the scsi devices disconnected from the scsi_host. The fc_host was torn
down during fc_remove_host.
Fix by moving the lpfc_pci_remove_one_s3/s4 calls to scsi_remove_host to
after the nodes are cleaned up. Remove the get_device and put_device calls
and the supporting code.
Link: https://lore.kernel.org/r/20201115192646.12977-4-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the driver has gone to a normal ref interface (with no odd logic)
the discovery logic needs to be updated to reworked so that it properly
takes references when it should and give them up when it should.
Rework the driver for the following get/put model:
- Move gets to just before an I/O is issued. Add gets for places where an
I/O was issued without one.
- Ensure that failures from lpfc_nlp_get() are handled by the driver.
- Check and fix the placement of lpfc_nlp_puts relative to io completions.
Note: some of these paths may not release the reference on the exact io
completion as the reference is held as the code takes another step in
the discovery thread and which may cause another io to be issued.
- Rearrange some code for error processing and calling lpfc_nlp_put.
- Fix some places of incorrect reference freeing that was causing the
premature releasing of the structure.
- Nvmet plogi handling performs unreg_rpi's. The reference counts were
unbalanced resulting in premature node removal. In some cases this
caused loss of node discovery. Corrected the reftaking around nvmet
plogis.
Nodes that experience devloss now get released from the node list now that
there is a proper reference taking.
Link: https://lore.kernel.org/r/20201115192646.12977-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a remote port is disconnected and disappears, its node structure
(ndlp) stays allocated and on a vport node list. While on the list it can
be matched, thus requires validation checks on state to be added in
numerous code paths. If the node comes back, its possible for there to be
multiple node structures for the same device on the vport node list. There
is no reason to keep the node structure around after it is no longer in
existence, and the current implementation creates problems for itself
(multiple nodes) and lots of unnecessary code for state validation.
Additionally, the reference taking on the node structure didn't follow the
normal model used by the kernel kref api. It included lots of odd logic to
match state with reference count. The combination of this odd logic plus
the way it was implicitly used in the discovery engine made its reference
taking implementation suspect and extremely hard to follow.
Change the driver such that the reference taking routines are now normal
ref increments/decrements and callout on refcount=0.
With this in place, the rework can be done such that the node structure is
fully removed and deallocated when the remote port no longer exists and all
references are removed. This removal logic, and the basic ref counting are
intrically tied, thus in a single patch.
Link: https://lore.kernel.org/r/20201115192646.12977-2-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Function parameter or member 'ctx_buf' not described in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'ctxp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'mp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'targetport' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'phba' not described in 'lpfc_nvmet_invalidate_host'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvmet_invalidate_host'
Link: https://lore.kernel.org/r/20201102142359.561122-15-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_nvme.c:256: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Excess function parameter 'nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1594: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2193: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20201102142359.561122-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201102142359.561122-11-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'phba' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'pring' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:1484: warning: Function parameter or member 'cmp' not described in 'lpfc_issue_ct_rsp'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'nemb_tp' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Function parameter or member 'job' not described in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Excess function parameter 'dmabuf' description in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4474: warning: Function parameter or member 'job' not described in 'lpfc_bsg_write_ebuf_set'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Function parameter or member 'job' not described in 'lpfc_bsg_issue_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Excess function parameter 'mb' description in 'lpfc_bsg_issue_mbox'
Link: https://lore.kernel.org/r/20201102142359.561122-8-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_debugfs.c:4204: warning: Function parameter or member 'len' not described in 'lpfc_idiag_queacc_read_qe'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Function parameter or member 'ctlregid' not described in 'lpfc_idiag_ctlacc_read_reg'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Excess function parameter 'drbregid' description in 'lpfc_idiag_ctlacc_read_reg'
Link: https://lore.kernel.org/r/20201102142359.561122-7-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4165:3:
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2792: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwpn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'attr' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Excess function parameter 'cdev' description in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'vpt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'tgt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Excess function parameter 'ndlp' description in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3264: warning: Function parameter or member 'lun_pri' not described in 'lpfc_oas_lun_get_next'
drivers/scsi/lpfc/lpfc_attr.c:3302: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_change'
drivers/scsi/lpfc/lpfc_attr.c:3376: warning: Function parameter or member 'count' not described in 'lpfc_oas_lun_store'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Function parameter or member 'vport' not described in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Excess function parameter 'phba' description in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'dev' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'attr' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'buf' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'count' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'phba' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'val' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4148: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_store'
drivers/scsi/lpfc/lpfc_attr.c:4302: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_show'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Function parameter or member 'buf' not described in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Excess function parameter 'buff' description in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'dev' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'attr' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'buf' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'count' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'phba' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'val' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:7117: warning: Function parameter or member 'verbose' not described in 'lpfc_hba_log_verbose_init'
Link: https://lore.kernel.org/r/20201102142359.561122-6-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel-doc does not understand this use-case.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4164:3:
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'dev' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'buf' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'dev' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'buf' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'attr' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'default' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'minval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'maxval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'phba' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'val' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'attr' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'default' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'minval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'maxval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'phba' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'val' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'dev' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'buf' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'count' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'val' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'cdev' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'count' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'field' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'format_string' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'sz' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'cast' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'cdev' description in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'buf' description in 'lpfc_rport_show_function'
Link: https://lore.kernel.org/r/20201102142359.561122-5-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:507: warning: Function parameter or member 'idx' not described in 'lpfc_sli4_io_xri_aborted'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:986: warning: Function parameter or member 'new_guard' not described in 'lpfc_bg_err_inject'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'txop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'rxop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'txopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'rxopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'txop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'rxop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'txopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'rxopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:2131: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl_prot'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Function parameter or member 't' not described in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Excess function parameter 'ptr' description in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Function parameter or member 'shost' not described in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Excess function parameter 'done' description in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Function parameter or member 'cmnd' not described in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Excess function parameter 'rdata' description in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'phba' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'pri' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Excess function parameter 'pha' description in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Function parameter or member 'phba' not described in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Excess function parameter 'pha' description in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Function parameter or member 'phba' not described in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Excess function parameter 'pha' description in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'phba' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'found_lun_pri' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Excess function parameter 'pha' description in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'phba' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'pri' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Excess function parameter 'pha' description in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'phba' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'pri' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Excess function parameter 'pha' description in 'lpfc_disable_oas_lun'
Link: https://lore.kernel.org/r/20201102142359.561122-4-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.5
Link: https://lore.kernel.org/r/20201020202719.54726-10-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that MIB support was registered with FDMI, the driver may receive CT
requests for MIB-related commands. At this time, no command is
supported. However, the driver needs to be graceful and reject the CT
request.
This patch adds identification of the requests as well as sending the
reject response.
Link: https://lore.kernel.org/r/20201020202719.54726-9-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created new attribute lpfc_enable_mi, which by default is enabled.
Add command definition bits for SLI-4 parameters that recognize whether the
adapter has MIB information support and what revision of MIB data. Using
the adapter information, register vendor-specific MIB support with FDMI.
The registration will be done every link up.
During FDMI registration, encountered a couple of errors when reverting to
FDMI rev1. Code needed to exist once reverting. Fixed these.
Link: https://lore.kernel.org/r/20201020202719.54726-8-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver supports arbitrarily large scatter-gather lists and the current
value for max_sectors is limiting.
Change max_sectors to the largest value. This was actually done prior but
it only corrected one template and that template was later removed.
So change the remaining 2 templates. Other areas which hard-set the sectors
value should be inheriting what is in the template.
Link: https://lore.kernel.org/r/20201020202719.54726-7-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code reviews duplicate code sections were found to determine the WQ
Create version. The duplication was potentially overriding logic that
validated page size.
Link: https://lore.kernel.org/r/20201020202719.54726-6-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 9816ef6ecb ("scsi: lpfc: Use after free in lpfc_rq_buf_free()")
was made to correct a use after free condition in lpfc_rq_buf_free().
Unfortunately, a subsequent patch cut on a tree without the fix
inadvertently reverted the fix.
Put the fix back: Move the freeing of the rqb_entry to after the print
function that references it.
Link: https://lore.kernel.org/r/20201020202719.54726-4-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c9 ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following calltrace was seen:
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
Fixes coccicheck warning:
drivers/scsi/lpfc/lpfc_attr.c:5341:5-11: Unneeded variable: "status". Return "- EINVAL" on line 5342
Link: https://lore.kernel.org/r/20200916022859.349089-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fail to issue the iocb in lpfc_gen_req() we need to drop the nodelist
reference.
Link: https://lore.kernel.org/r/20200910084059.138507-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Three fixes: one in drivers (lpfc) and two for zoned block devices.
The latter also impinges on the block layer but only to introduce a
new block API for setting the zone model rather than fiddling with the
queue directly in the zoned block driver.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX29mRyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishabnAP48vMYD
/cjyGAJfq/0k/U/t6pRPc5tUm89LOWcOJz0SjwD/YXcQNz7mx8MxnypAV1jbWXR7
iyWkPMYVc4EJh7oTARE=
=SQhI
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: one in drivers (lpfc) and two for zoned block devices.
The latter also impinges on the block layer but only to introduce a
new block API for setting the zone model rather than fiddling with the
queue directly in the zoned block driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: sd_zbc: Fix ZBC disk initialization
scsi: sd: sd_zbc: Fix handling of host-aware ZBC disks
scsi: lpfc: Fix initial FLOGI failure due to BBSCN not supported
Initial FLOGIs are failing with the following message:
lpfc 0000:13:00.1: 1:(0):0820 FLOGI Failed (x300). BBCredit Not Supported
In a prior patch, the READ_SPARAM command was re-ordered to post after
CONFIG_LINK as the driver is expected to update the driver's copy of the
service parameters for the FLOGI payload. If the bb-credit recovery feature
is enabled, this is fine. But on adapters were bb-credit recovery isn't
enabled, it would cause the FLOGI to fail.
Fix by restoring the original command order (READ_SPARAM before
CONFIG_LINK), and after issuing CONFIG_LINK, detect bb-credit recovery
support and reissuing READ_SPARAM to obtain the updated service parameters
(effectively adding in the fix command order).
[mkp: corrected SHA]
Link: https://lore.kernel.org/r/20200911200147.110826-1-james.smart@broadcom.com
Fixes: 835214f5d5 ("scsi: lpfc: Fix broken Credit Recovery after driver load")
CC: <stable@vger.kernel.org> # v5.7+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
not used [-Wunused-but-set-variable]
struct lpfc_sli4_hdw_queue *qp;
^
Link: https://lore.kernel.org/r/20200909082716.37787-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/lpfc/lpfc_debugfs.c: In function ‘lpfc_debugfs_hdwqstat_data’:
drivers/scsi/lpfc/lpfc_debugfs.c:1699:30: warning: variable ‘qp’ set but
Eleven fixes, mostly in drivers or minor fixes in driver related
infrastructure libraries (target, libfc and libsas). Most of the bugs
fixed only show up under rare circumstances, the exception being the
endianness problem in qla2xxx which is used as a device on some sparc
systems.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX1egVyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishShgAP9McHKn
9T/m2mAjBr8IMZRlD4Y6nC+ToxDdRDsYT6iAOQD/ZO1FajxEcGC4xEtWznvXtqGk
H1Lfr/ta19GSEPqaZ44=
=rDo9
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eleven fixes, mostly in drivers or minor fixes in driver related
infrastructure libraries (target, libfc and libsas).
Most of the bugs fixed only show up under rare circumstances, the
exception being the endianness problem in qla2xxx which is used as a
device on some sparc systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: Don't call disable_irq from IRQ poll handler
scsi: megaraid_sas: Don't call disable_irq from process IRQ poll
scsi: target: iscsi: Fix hang in iscsit_access_np() when getting tpg->np_login_sem
scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA
scsi: target: iscsi: Fix data digest calculation
scsi: lpfc: Update lpfc version to 12.8.0.4
scsi: lpfc: Extend the RDF FPIN Registration descriptor for additional events
scsi: lpfc: Fix FLOGI/PLOGI receive race condition in pt2pt discovery
scsi: lpfc: Fix setting IRQ affinity with an empty CPU mask
scsi: qla2xxx: Fix regression on sparc64
scsi: libfc: Fix for double free()
scsi: pm8001: Fix memleak in pm8001_exec_internal_task_abort
Update lpfc version to 12.8.0.4
Link: https://lore.kernel.org/r/20200828175332.130300-5-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver registers for Link Integrity events only.
This patch adds registration for the following FPIN types:
- Delivery Notifications
- Congestion Notification
- Peer Congestion Notification
Link: https://lore.kernel.org/r/20200828175332.130300-4-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some systems are reporting the following log message during driver unload
or system shutdown:
ics_rtas_set_affinity: No online cpus in the mask
A prior commit introduced the writing of an empty affinity mask in calls to
irq_set_affinity_hint() when disabling interrupts or when there are no
remaining online CPUs to service an eq interrupt. At least some ppc64
systems are checking whether affinity masks are empty or not.
Do not call irq_set_affinity_hint() with an empty CPU mask.
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20200828175332.130300-2-james.smart@broadcom.com
Cc: <stable@vger.kernel.org> # v5.5+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the set of patches which arrived too late to stabilise in
-next for the first pull. It's really just an lpfc driver update and
an assortment of minor fixes, all in drivers. The only core update is
to the zone block device driver, which isn't the one most people use.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXza9yiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYyiAQCUJJ8m
vraqyBzjAPWpPsoNZmrvUxciXEDhoLrFo4Nl8wEAoJPVjUd79dXCJHB1Oq+MaeaF
LODgv2bO1F4TCf59F+4=
=+wdb
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of patches which arrived too late to stabilise in
-next for the first pull.
It's really just an lpfc driver update and an assortment of minor
fixes, all in drivers. The only core update is to the zone block
device driver, which isn't the one most people use"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Update lpfc version to 12.8.0.3
scsi: lpfc: Fix LUN loss after cable pull
scsi: lpfc: Fix validation of bsg reply lengths
scsi: lpfc: Fix retry of PRLI when status indicates its unsupported
scsi: lpfc: Fix oops when unloading driver while running mds diags
scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter
scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value
scsi: lpfc: Fix FCoE speed reporting
scsi: lpfc: Add missing misc_deregister() for lpfc_init()
scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport
scsi: scsi_transport_sas: Add spaces around binary operator "|"
scsi: sd_zbc: Improve zone revalidation
scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases
scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del()
scsi: target: Make iscsit_register_transport() return void
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a
huge docbook fix update like most other subsystems and no major update
to the core (the few non trivial updates are either minor fixes or
removing an unused feature [scsi_sdb_cache]).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXyxq1yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSoAAQChZ4i8
ZqYW3pL33JO3fA8vdjvLuyC489Hj4wzIsl3/bQEAxYyM6BSLvMoLWR2Plq/JmTLm
4W/LDptarpTiDI3NuDc=
=4b0W
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
Update lpfc version to 12.8.0.3
Link: https://lore.kernel.org/r/20200803210229.23063-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On devices that support FCP sequence error recovery, which attempts to
preserve the devices login across link bounce, adisc is used for device
validation. Turns out the device fc4 type is cleared as part of the link
bounce, but the ADISC handling doesn't restore the FC4 support as it
normally would with a PRLI. This caused situations where the device wasn't
reregistered with the transport thus scan logic and LUN discovery never
kicked in.
In the ADISC completion handling, reset the fc4 type so that transport port
reregistration occurs with the remote port.
Link: https://lore.kernel.org/r/20200803210229.23063-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of code areas which validate sufficient reply buffer
length, but the checks are using the request elements rather than the reply
elements.
Rework to validate using the reply structures.
Link: https://lore.kernel.org/r/20200803210229.23063-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With port bounce/address swaps and timing between initiator GID queries vs
remote port FC4 support registrations, the driver may be in a situation
where it sends PRLIs for both FCP and NVME even though the target may not
support one of the protocols. In this case, the remote port will reject the
PRLI and usually indicate it does not support the request. However, the
driver currently ignores the status of the failure and immediately retries
the PRLI, which is pointless. In the case of this one remote port, the
reception of the PRLI retry caused it to decide to send a LOGO. The LOGO
restarted the process and the same results happened. It made the remote
port undiscoverable to either protocol.
Add logic to detect the non-support status and not attempt the retry
of the PRLI.
Link: https://lore.kernel.org/r/20200803210229.23063-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While mds diagnostic tests are running, if the driver is requested to be
unloaded, oops or hangs are observed. The driver doesn't terminate the
processing of diag frames when the unload is started. As such: oops may be
seen for __lpfc_sli_release_iocbq_s4 because ring memory is referenced that
was already freed; or hangs see in lpfc_nvme_wait_for_io_drain as ios no
longer complete.
If unloading, don't process diag frames. Just clean them up.
Link: https://lore.kernel.org/r/20200803210229.23063-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In configs with a large number of initiators in the same zone (>250), RSCN
timeouts are seen when creating or deleting vports:
lpfc 0000:07:00.1: 5:(0):0231 RSCN timeout Data: x0 x3
During RSCN processing driver issues GID_FT command to nameserver. A
counter for number of simultaneous GID_FT commands is maintained (an
unsigned value). The counter is incremented when the GID_FT is issued. If
the GID_FT command fails for some reason the driver retries the GID_FT from
the completion call back. But the counter was decremented before the retry
was issued. When the second GID_FT completes, the callback again tries to
decrement the counter, possibly wrapping to a very large non-zero value,
which causes the RSCN cleanup code to not execute. Thus the RSCN timeout
failure.
Do not decrement the counter on a retry. Also add defensive checks to
ensure the counter is not decremented if already zero.
Link: https://lore.kernel.org/r/20200803210229.23063-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module parameters override the default configuration settings for
hardware queues or irqs, the driver was not notifying the change from
defaults.
Revise such that any changes will result in a kernel log message.
Link: https://lore.kernel.org/r/20200803210229.23063-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current Link speed was shown as "unknown" in sysfs for FCoE ports. In this
scenario, the port was working in 20G speed, which happens to not be a
speed handled by the driver.
Add support for all possible link speeds that could get reported from
port_speed field in link state ACQE.
Additionally, as supported_speeds can't be manipulated via the FCoE driver
on a converged ethernet port (it must be managed by the nic function),
don't fill out the supported_speeds field for the fc host object in sysfs.
Revise debug logging to report Link speed mgmt valuess.
Link: https://lore.kernel.org/r/20200803210229.23063-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_init() misses a call misc_deregister() in an error path. Add a label
'unregister' to fix it.
Link: https://lore.kernel.org/r/20200731065639.190646-1-jingxiangfeng@huawei.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a crash if slub_debug=FZPU is
enabled.
An earlier fix put put the completion on the stack, but commit 2a0fb340fc
("scsi: lpfc: Correct localport timeout duration error") subsequently
changed the code to reference the completion through a pointer in the
object rather than the local stack variable. Fix this by using the stack
variable directly.
Link: https://lore.kernel.org/r/20200729231011.13240-1-emilne@redhat.com
Fixes: 2a0fb340fc ("scsi: lpfc: Correct localport timeout duration error")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nportdisc.c:1079: warning: Function parameter or member 'ndlp' not described in 'lpfc_release_rpi'
Link: https://lore.kernel.org/r/20200723122446.1329773-20-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding, removing and correcting function parameter descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Function parameter or member 'vport' not described in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'phba' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'vpi' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'sid' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:1218: warning: Function parameter or member 'ring' not described in 'lpfc_config_ring'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Function parameter or member 'mboxq' not described in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Excess function parameter 'cmd' description in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1710: warning: Function parameter or member 'sge' not described in 'lpfc_sli4_mbx_sge_get'
drivers/scsi/lpfc/lpfc_mbox.c:1780: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_config'
drivers/scsi/lpfc/lpfc_mbox.c:2027: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli4_mbx_read_fcf_rec'
drivers/scsi/lpfc/lpfc_mbox.c:2078: warning: Function parameter or member 'phba' not described in 'lpfc_request_features'
Link: https://lore.kernel.org/r/20200723122446.1329773-19-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Function parameter or member 't' not described in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Excess function parameter 'ptr' description in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Function parameter or member 't' not described in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Excess function parameter 'ptr' description in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1232: warning: Function parameter or member 'work' not described in 'lpfc_idle_stat_delay_work'
drivers/scsi/lpfc/lpfc_init.c:1817: warning: Function parameter or member 'en_rn_msg' not described in 'lpfc_sli4_port_sta_fn_reset'
drivers/scsi/lpfc/lpfc_init.c:3033: warning: Function parameter or member 'mbx_action' not described in 'lpfc_block_mgmt_io'
drivers/scsi/lpfc/lpfc_init.c:3481: warning: Function parameter or member 'mbx_action' not described in 'lpfc_offline_prep'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'phba' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'vport' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Function parameter or member 't' not described in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Excess function parameter 'ptr' description in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:5103: warning: Excess function parameter 'evt_code' description in 'lpfc_async_link_speed_to_read_top'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Function parameter or member 'acqe_sli' not described in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Excess function parameter 'acqe_fc' description in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Excess function parameter 'vport' description in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Function parameter or member 'acqe_fip' not described in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Function parameter or member 'acqe_dcbx' not described in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Function parameter or member 'acqe_grp5' not described in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:7279: warning: Function parameter or member 'iocb_count' not described in 'lpfc_init_iocb_list'
drivers/scsi/lpfc/lpfc_init.c:8227: warning: Function parameter or member 'if_type' not described in 'lpfc_sli4_bar1_register_memmap'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'phba' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'rdconf' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:10734: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:11241: warning: Function parameter or member 'eqlist' not described in 'lpfc_cpuhp_get_eq'
drivers/scsi/lpfc/lpfc_init.c:11726: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli4_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:12997: warning: Excess function parameter 'ret' description in 'lpfc_write_firmware'
drivers/scsi/lpfc/lpfc_init.c:13103: warning: Function parameter or member 'fw_upgrade' not described in 'lpfc_sli4_request_firmware_update'
Link: https://lore.kernel.org/r/20200723122446.1329773-17-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_init.c: In function ‘lpfc_dbg_print’:
drivers/scsi/lpfc/lpfc_init.c:14212:6: warning: function ‘lpfc_dbg_print’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
14212 | sizeof(phba->dbg_log[idx].log), fmt, args);
| ^~~~~~
Link: https://lore.kernel.org/r/20200723122446.1329773-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_hbadisc.c:1209: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_clear_fcf_rr_bmask'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Function parameter or member 'sw_name' not described in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Excess function parameter 'fab_name' description in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Function parameter or member 'fcf_rec' not described in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Excess function parameter 'fcf' description in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1956: warning: Cannot understand lpfc_sli4_fcf_record_match - testing new FCF record for matching existing FCF
on line 1956 - I thought it was a doc line
drivers/scsi/lpfc/lpfc_hbadisc.c:2078: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_del'
drivers/scsi/lpfc/lpfc_hbadisc.c:2109: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_set_fcf_flogi_fail'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_add'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'new_fcf_record' not described in 'lpfc_sli4_fcf_pri_list_add'
Link: https://lore.kernel.org/r/20200723122446.1329773-3-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Function parameter or member 't' not described in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Excess function parameter 'ptr' description in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:4877: warning: Function parameter or member 'rejectError' not described in 'lpfc_els_rsp_reject'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Function parameter or member 't' not described in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Excess function parameter 'ptr' description in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Function parameter or member 'payload' not described in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Excess function parameter 'cmd' description in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Function parameter or member 'tlv' not described in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Excess function parameter 'lnk_not' description in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Function parameter or member 't' not described in 'lpfc_fabric_block_timeout'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Excess function parameter 'ptr' description in 'lpfc_fabric_block_timeout'
Link: https://lore.kernel.org/r/20200723122446.1329773-2-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'pg_addr' is only used when CONFIG_X86 is defined. So only declare it if
CONFIG_X86 is defined.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
drivers/scsi/lpfc/lpfc_sli.c:15813:16: warning: unused variable ‘pg_addr’ [-Wunused-variable]
15813 | unsigned long pg_addr;
| ^~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-37-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Other headers have been demoted as they are too far out of sync and ideally
require effort from the authors.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'usr_flg' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'num_entry' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'tmo' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'retry' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'rsp_size' not described in 'lpfc_ct_cmd'
drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'retry' not described in 'lpfc_ct_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'cmdcode' not described in 'lpfc_fdmi_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'new_mask' not described in 'lpfc_fdmi_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3272: warning: Function parameter or member 't' not described in 'lpfc_delayed_disc_tmo'
Link: https://lore.kernel.org/r/20200721164148.2617584-31-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c:257: warning: Function parameter or member 'mqe' not described in 'lpfc_sli4_mq_put'
drivers/scsi/lpfc/lpfc_sli.c:257: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_mq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hrqe' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'drqe' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:1021: warning: Function parameter or member 'xritag' not described in 'lpfc_test_rrq_active'
drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_els_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_els_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_nvmet_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_nvmet_sglq'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Function parameter or member 'rb_list' not described in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'phba' description in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Function parameter or member 'hrq' not described in 'lpfc_sli_rqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_rqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Function parameter or member 't' not described in 'lpfc_poll_eratt'
drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Excess function parameter 'ptr' description in 'lpfc_poll_eratt'
drivers/scsi/lpfc/lpfc_sli.c:4115: warning: Excess function parameter 'pring' description in 'lpfc_sli_abort_fcp_rings'
drivers/scsi/lpfc/lpfc_sli.c:5331: warning: Excess function parameter 'mboxq' description in 'lpfc_sli4_read_fcoe_params'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'type' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'mbox' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Function parameter or member 'pmb' not described in 'lpfc_sli4_ras_mbox_cmpl'
drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Excess function parameter 'pmboxq' description in 'lpfc_sli4_ras_mbox_cmpl'
drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_get_allocated_extnts'
drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Excess function parameter 'extnt_count' description in 'lpfc_sli4_get_allocated_extnts'
drivers/scsi/lpfc/lpfc_sli.c:7064: warning: Excess function parameter 'pring' description in 'lpfc_sli4_repost_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:7312: warning: Function parameter or member 'phba' not described in 'lpfc_init_idle_stat_hb'
drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Function parameter or member 't' not described in 'lpfc_mbox_timeout'
drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Excess function parameter 'ptr' description in 'lpfc_mbox_timeout'
drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli_issue_mbox_s4'
drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Excess function parameter 'pmbox' description in 'lpfc_sli_issue_mbox_s4'
drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Function parameter or member 'piocbq' not described in 'lpfc_sli4_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Function parameter or member 'iocbq' not described in 'lpfc_sli4_iocb2wqe'
drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_iocb2wqe'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'phba' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'ring_number' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'piocb' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'flag' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Function parameter or member 'cmd' not described in 'lpfc_sli_abort_taskmgmt'
drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Excess function parameter 'taskmgmt_cmd' description in 'lpfc_sli_abort_taskmgmt'
drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb_wait'
drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb_wait'
drivers/scsi/lpfc/lpfc_sli.c:12262: warning: Function parameter or member 'mbx_action' not described in 'lpfc_sli_mbox_sys_shutdown'
drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Function parameter or member 'irspiocbq' not described in 'lpfc_sli4_els_wcqe_to_rspiocbq'
drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Excess function parameter 'wcqe' description in 'lpfc_sli4_els_wcqe_to_rspiocbq'
drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_async_event'
drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_async_event'
drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_mbox_event'
drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_mbox_event'
drivers/scsi/lpfc/lpfc_sli.c:13441: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_sp_handle_mcqe'
drivers/scsi/lpfc/lpfc_sli.c:13768: warning: Function parameter or member 'speq' not described in 'lpfc_sli4_sp_handle_eqe'
drivers/scsi/lpfc/lpfc_sli.c:14126: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_nvmet_handle_rcqe'
drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Function parameter or member 'cqe' not described in 'lpfc_sli4_fp_handle_cqe'
drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Excess function parameter 'eqe' description in 'lpfc_sli4_fp_handle_cqe'
drivers/scsi/lpfc/lpfc_sli.c:14336: warning: Function parameter or member 'eq' not described in 'lpfc_sli4_hba_handle_eqe'
drivers/scsi/lpfc/lpfc_sli.c:14808: warning: Function parameter or member 'entry_count' not described in 'lpfc_sli4_queue_alloc'
drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'type' not described in 'lpfc_cq_create'
drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create'
drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'type' not described in 'lpfc_cq_create_set'
drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create_set'
drivers/scsi/lpfc/lpfc_sli.c:16063: warning: Function parameter or member 'subtype' not described in 'lpfc_rq_create'
drivers/scsi/lpfc/lpfc_sli.c:16353: warning: Function parameter or member 'subtype' not described in 'lpfc_mrq_create'
drivers/scsi/lpfc/lpfc_sli.c:16533: warning: Function parameter or member 'phba' not described in 'lpfc_eq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16590: warning: Function parameter or member 'phba' not described in 'lpfc_cq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'phba' not described in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'mq' not described in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Excess function parameter 'qm' description in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16698: warning: Function parameter or member 'phba' not described in 'lpfc_wq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'phba' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'hrq' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'drq' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Excess function parameter 'rq' description in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16940: warning: Function parameter or member 'xri' not described in '__lpfc_sli4_free_xri'
drivers/scsi/lpfc/lpfc_sli.c:16955: warning: Function parameter or member 'xri' not described in 'lpfc_sli4_free_xri'
drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Function parameter or member 'post_cnt' not described in 'lpfc_sli4_post_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Excess function parameter 'count' description in 'lpfc_sli4_post_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17221: warning: Function parameter or member 'sb_count' not described in 'lpfc_sli4_post_io_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17451: warning: Function parameter or member 'did' not described in 'lpfc_fc_frame_to_vport'
drivers/scsi/lpfc/lpfc_sli.c:17590: warning: Function parameter or member 'vport' not described in 'lpfc_fc_frame_add'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'vport' not described in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'aborted' not described in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Excess function parameter 'phba' description in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Function parameter or member 'seq_dmabuf' not described in 'lpfc_prep_seq'
drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Excess function parameter 'dmabuf' description in 'lpfc_prep_seq'
drivers/scsi/lpfc/lpfc_sli.c:18332: warning: Function parameter or member 'dmabuf' not described in 'lpfc_sli4_handle_received_buffer'
drivers/scsi/lpfc/lpfc_sli.c:18655: warning: Function parameter or member 'rpi' not described in '__lpfc_sli4_free_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18683: warning: Function parameter or member 'rpi' not described in 'lpfc_sli4_free_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'ndlp' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'cmpl' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'arg' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Excess function parameter 'phba' description in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:19103: warning: Function parameter or member 'phba' not described in 'lpfc_check_next_fcf_pri_level'
drivers/scsi/lpfc/lpfc_sli.c:19266: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_set'
drivers/scsi/lpfc/lpfc_sli.c:19295: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_clear'
drivers/scsi/lpfc/lpfc_sli.c:19331: warning: Function parameter or member 'mbox' not described in 'lpfc_mbx_cmpl_redisc_fcf_table'
drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Function parameter or member 'pwqeq' not described in 'lpfc_wqe_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Excess function parameter 'pwqe' description in 'lpfc_wqe_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Function parameter or member 'qp' not described in 'lpfc_sli4_issue_wqe'
drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Excess function parameter 'ring_number' description in 'lpfc_sli4_issue_wqe'
drivers/scsi/lpfc/lpfc_sli.c:20434: warning: Function parameter or member 'qp' not described in '_lpfc_move_xri_pbl_to_pvt'
drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Function parameter or member 'hwqid' not described in 'lpfc_keep_pvt_pool_above_lowwm'
drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Excess function parameter 'qp' description in 'lpfc_keep_pvt_pool_above_lowwm'
drivers/scsi/lpfc/lpfc_sli.c:20682: warning: Function parameter or member 'qp' not described in 'lpfc_get_io_buf_from_private_pool'
Link: https://lore.kernel.org/r/20200721164148.2617584-24-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
drivers/scsi/lpfc/lpfc_sli.c:15810:16: warning: variable ‘pg_addr’ set but not used [-Wunused-but-set-variable]
15810 | unsigned long pg_addr;
| ^~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Either due to API slippage before the driver was mainlined or copy/paste
errors.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'qsize' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:689: warning: Function parameter or member 'gen_req_cmp' not described in '__lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'phba' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'pwqeIn' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'wcqe' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'pnode' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'cstat' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1598: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2197: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20200713080001.128044-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
nvme-fc allows the driver to specify a default devloss_tmo value when
registering the remote port. The lpfc driver is currently not doing so,
although it is implementing a driver internal node loss value of 30s which
also is used on the SCSI FC remote port. As no devloss_tmo is set, the
nvme-fc transport defaults to 60s. So there are competing timers.
Additionally, due to the competing timers, it is possible the NVMe rport is
removed but the SCSI rport remains. It is possible that the SCSI FC rport,
which was registered for the NVMe port even if it doesn't utilize the SCSI
protocol, had been tuned to not match either the 60s (nvme-fc default) or
30s (lldd default), it gets out of whack. The lldd will defer to the SCSI
FC rport as long as the SCSI FC rport has not had its devloss_tmo expire.
Correct the situation by specifying a default devloss_tmo to the nvme-fc
transport when registering the rport. Take the value from the SCSI FC
rport if it exists, otherwise use the driver default.
Link: https://lore.kernel.org/r/20200714211412.11773-1-jsmart2021@gmail.com
Tested-by: Martin George <Martin.George@netapp.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a big box the lpfc driver emits a few thousand "Set Affinity" lines to
the console. Reduce the priority of these from KERN_ERR to KERN_INFO, and
also fix a few printks that had no log level.
Link: https://lore.kernel.org/r/20200713083908.1104927-1-anton@ozlabs.org
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The expression start_idx - dbg_cnt is evaluated using unsigned int
arthithmetic (since these variables are unsigned ints) and hence can never
be less than zero, so the less than comparison is never true. Rewrite the
expression to check for start_idx being less than dbg_cnt.
After the logic was corrected, temp_idx wasn't working correctly. So fix it
as well.
Link: https://lore.kernel.org/r/20200706204246.130416-1-jsmart2021@gmail.com
Fixes: 372c187b8a ("scsi: lpfc: Add an internal trace log buffer")
CC: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unsigned compared against 0")
With certain platforms its possible pci_alloc_irq_vectors() may affinitize
irq vectors to multiple (all?) CPUs. The driver is currently assuming
exclusivity and vectors being doled out to different CPUs and is assigning
primary ownership of each vector to the first CPU in the mask. The code
doesn't bother to check if the CPU already owns a vector and will
unconditionally overwrite the CPU to vector mapping. This causes the
relationships between eq's and cq's to get confused and gets worse when
CPUs start to offline. The net results are interrupts are skipped resulting
in mailbox timeouts and there are oopses in CPU offling flows.
Fix this changing up the primary vector assignment. Now assign the eq to a
CPU only if it is the CPU in the mask that does not have a prior
assignment. And once the primary ownership is assigned, break from the
loop. For CPUs that may have been set before but not the primary owner, the
lpfc_cpu_affinity_check() routine will balance the CPU to eq assignment.
Link: https://lore.kernel.org/r/20200706204230.130363-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix smatch warning:
drivers/scsi/lpfc/lpfc_sli.c:15156 lpfc_cq_poll_hdler() warn:
inconsistent indenting
Link: https://lore.kernel.org/r/20200707150018.823350-1-colin.king@canonical.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although the existing implementation is very good at high I/O load, on
tests involving light load, especially on only a few hardware queues,
latency was a little higher than it can be due to using workqueue
scheduling. Other tasks in the system can delay handling.
Change the lower level to use irq_poll by default which uses a softirq for
I/O completion. This gives better latency as variance in when the cq is
processed is reduced over the workqueue interface. However, as high load is
better served by not being in softirq when the CPU is loaded, work queues
are still used under high I/O load.
Link: https://lore.kernel.org/r/20200630215001.70793-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, if there has been an issue whereby an adapter dump was taken,
there is nothing displayed to hint that it is present. Utilities must be
run and they must query for the status in order to then download the dump.
Add a message to the driver to query dump image presence when initializing
the SLI Port.
Link: https://lore.kernel.org/r/20200630215001.70793-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver validates command codes received from the
application. COMMON_SET_FEATURES is not currently being approved.
Add definition of the missing command and allow it to be issued by
applications.
Link: https://lore.kernel.org/r/20200630215001.70793-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change vocabulary of 0373 log msg from "error" to "cmpl" The current
language of the 0373 message contains the word "error" which caused a
number of customers to inquire about the "error" and if it should be a
concern. It isn't an error, it's simply an io completion status.
Revise the message to replace the word "error" with "cmpl" for completion.
Link: https://lore.kernel.org/r/20200630215001.70793-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the kdump kernel shuts down lpfc calls flush_work_queue on an
interrupt to schedule the cq handler. When there is only one CPU active on
the kdump kernel, it is possible for the work_on to get scheduled on a
non-active CPU causing it to never be scheduled.
When in the kdump environment, per-CPU affinity of cq's to cpus is not
necessary. In those cases, use a general queue_work rather than a
queue_work_on().
Link: https://lore.kernel.org/r/20200630215001.70793-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call traces have been observed running different tests that involve aborts
and setting the rrq active flag. The lpfc_set_rrq_active routine is doing
a mempool_alloc under the soft_irq processing level. When the mempool needs
to get a new buffer from the free pool and has to wait for memory to become
free it will check the flags passed in on the alloc and dump the stack if
the thread is running in interrupt context.
Replace the GFP_KERNEL flag with GFP_ATOMIC so that the memory allocation
will not attempt to sleep if there is no mem available.
Link: https://lore.kernel.org/r/20200630215001.70793-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using DUMP on SLI3 to read VPD and Port status data (config region
23), the adapter is overruning the kmalloc'd buffer causing havoc on other
consumers of the allocation pools.
Rework the loops processing the dump data and validate/size memory lengths
before performing bcopy.
Link: https://lore.kernel.org/r/20200630215001.70793-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Visual code inspection of the MDS implementation revealed two errors in
the driver:
- The set features Feature Code had an incorrect value
- The routine that classifies command type for cmd completions was missing
the Send Frame definition. Send Frame is used for MDS driver loopback.
Link: https://lore.kernel.org/r/20200630215001.70793-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following error:
Assigned value that is never used may represent unnecessary computation.
The rc variable was initially assigned a value but in several cases, when
an error case is detected, it is reassigned a new value. The initial value
had little use.
In code-reviewing this routine, it could use some cleanup:
- Setting the initialization value to -ENODEV is a much better choice and
lessens code in the routine.
- The wasn't tracking logic errors vs no error and mailbox failure.
Better to resolve by adding a status to track the mailbox failure
and merge it with the logic error when the routine returns.
Link: https://lore.kernel.org/r/20200630215001.70793-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with
general hdw_queues per cpu") has introduced static checker warnings for
potential null dereferences in 'lpfc_sli4_hba_unset()' and commit 1ffdd2c044
("scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset") has
tried to fix it. However, yet another potential null dereference is
remaining. This commit fixes it.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Link: https://lore.kernel.org/r/20200623084122.30633-1-sjpark@amazon.com
Fixes: 1ffdd2c044 ("scsi: lpfc: resolve static checker warning inlpfc_sli4_hba_unset")
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates. There are no major core changes in this
series apart from a refactoring in scsi_lib.c.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXtq5QyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXyGAQCipTWx
7kHKHZBCVTU133bADt3+SstLrAm8PKZEXMnP9wEAzu4QkkW8URxEDRrpu7qk5gbA
9M/KyqvfRtTH7+BSK7M=
=J6aO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
:This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates.
There are no major core changes in this series apart from a
refactoring in scsi_lib.c"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: ti-j721e-ufs: Fix unwinding of pm_runtime changes
scsi: cxgb3i: Fix some leaks in init_act_open()
scsi: ibmvscsi: Make some functions static
scsi: iscsi: Fix deadlock on recovery path during GFP_IO reclaim
scsi: ufs: Fix WriteBooster flush during runtime suspend
scsi: ufs: Fix index of attributes query for WriteBooster feature
scsi: ufs: Allow WriteBooster on UFS 2.2 devices
scsi: ufs: Remove unnecessary memset for dev_info
scsi: ufs-qcom: Fix scheduling while atomic issue
scsi: mpt3sas: Fix reply queue count in non RDPQ mode
scsi: lpfc: Fix lpfc_nodelist leak when processing unsolicited event
scsi: target: tcmu: Fix a use after free in tcmu_check_expired_queue_cmd()
scsi: vhost: Notify TCM about the maximum sg entries supported per command
scsi: qla2xxx: Remove return value from qla_nvme_ls()
scsi: qla2xxx: Remove an unused function
scsi: iscsi: Register sysfs for iscsi workqueue
scsi: scsi_debug: Parser tables and code interaction
scsi: core: Refactor scsi_mq_setup_tags function
scsi: core: Fix incorrect usage of shost_for_each_device
scsi: qla2xxx: Fix endianness annotations in source files
...
