On init we have sequence:
for_each_card_prelinks(card, i, dai_link) {
ret = snd_soc_add_pcm_runtime(card, dai_link);
ret = init_some_other_things(...);
if (ret)
goto probe_end:
for_each_card_rtds(card, rtd) {
ret = soc_init_pcm_runtime(card, rtd);
probe_end:
while on exit:
for_each_card_rtds(card, rtd)
snd_soc_link_exit(rtd);
If init_some_other_things() step fails due to error we end up with
not fully setup rtds and try to call snd_soc_link_exit on them, which
depending on contents on .link_exit handler, can end up dereferencing
NULL pointer.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When printing log related to component it is useful to know, to which
component it applies to.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.
- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt
If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.
During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.
When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.
For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.
Fixes: 41cb85bc4b ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the pll_id and pll_id can be zero (WM8960_SYSCLK_AUTO)
with the commit 2bbc2df46e ("ASoC: wm8960: Make automatic the
default clocking mode")
Then the machine driver will skip to call set_sysclk() and set_pll()
for codec, when the sysclk rate is different with what wm8960 read
at probe, the output sound frequency is wrong.
So change the fll_id and pll_id initial value, still keep machine
driver's behavior same as before.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695202992-24864-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.
Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.
The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error
Fixes: 269f399dc1 ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While browsing/grepping in the sound core, I found that
snd_dmaengine_set_config_from_dai_data() did not exist, in favor of
snd_dmaengine_pcm_set_config_from_dai_data(). Fix the typo.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922161547.594484-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_probe() is used for both "DT probe" (A) and "platform probe"
(B). It uses "goto err" when error case, but it is not needed for
"platform probe" case (B). Thus it is using "return" directly there.
static int asoc_simple_probe(...)
{
^ if (...) {
| ...
(A) if (ret < 0)
| goto err;
v } else {
^ ...
| if (ret < 0)
(B) return -Exxx;
v }
...
^ if (ret < 0)
(C) goto err;
v ...
err:
(D) simple_util_clean_reference(card);
return ret;
}
Both case are using (C) part, and it calls (D) when err case.
But (D) will do nothing for (B) case.
Because of these behavior, current code itself is not wrong,
but is confusable, and more, static analyzing tool will warning on
(B) part (should use goto err).
To avoid static analyzing tool warning, this patch uses "goto err"
on (B) part.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7hy7mlh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rule for the SoundWire tables is that the platforms with more
devices need to be added first. We broke that rule with the Dell SKU
0B34, and caused the second amplifier for SKU 0AF3 to be ignored.
The fix is simple, we need to move the single-amplifier entry after
the two-amplifier one.
Fixes: b62a1a839b ("ASoC: Intel: soc-acpi: add tables for Dell SKU 0B34")
Closes: https://github.com/thesofproject/linux/issues/4559
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919083606.1920202-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding HDMI-In capture via I2S feature support in MTL platform.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support for ES83x6 codec in MTL match table.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fail paths during probe will free up the ops, on remove we should
only free it if the probe was successful.
Fixes: bc433fd76f ("ASoC: SOF: Add ops_free")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230915124015.19637-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
20s seems unnecessarily large for the DSP init timeout. This coupled with
multiple FW boot attempts causes an excessive delay in the error path when
booting in recovery mode. Reduce it to 0.5s and use the existing
HDA_DSP_INIT_TIMEOUT_US.
Link: https://github.com/thesofproject/linux/issues/4565
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230915134153.9688-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The microphone and speaker shutters on cs42l43 can be configured to
trigger from the same GPIO, in this case the current code returns an
error as we attempt to request two IRQ handlers for the same IRQ. Fix
this by always requesting the shutter IRQs with the IRQF_SHARED flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230915144300.120100-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_clk_get() can return -EPROBE_DEFER error,
modify the error code to be -EINVAL is not correct, which
cause the -EPROBE_DEFER error is not correctly handled.
This patch is to fix the return error code.
Fixes: b86ef53677 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1694757731-18308-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because of the potential failure of the devm_kstrdup(), the
dl[i].codecs->name could be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.
Fixes: 97030a4337 ("ASoC: Intel: avs: Add HDAudio machine board")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230915021344.3078-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the widget setup fails we should only decrement the core usage
count if the sof_widget_free_unlocked() has not been called as part of
the error handling.
sof_widget_free_unlocked() calls snd_sof_dsp_core_put() and the additional
core_put will cause imbalance in core usage count.
Use the existing use_count_decremented to handle this issue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230914124725.17397-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
available_fmt is a pointer.
Fixes: 4fdef47a44 ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230914132504.18463-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
i.MX rpmsg sound cards work on codec slave mode. MCLK will be disabled
by CPU DAI driver in hw_free(). Some codec requires MCLK present at
power up/down sequence. So need to set ignore_pmdown_time to power down
codec immediately before MCLK is turned off.
Take WM8962 as an example, if MCLK is disabled before DAPM power down
playback stream, FIFO error will arise in WM8962 which will have bad
impact on playback next.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230913102656.2966757-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
These patches fix 3 problems with hard reset:
1. Ensure a minimum reset pulse width
2. Deal with ACPI overriding the requested default GPIO state
3. Avoid a race condition when hard-resetting a SoundWire peripheral
that is already enumerated
wm_adsp_read_ctl() and wm_adsp_write_ctl() must hold the cs_dsp pwr_lock
mutex when calling cs_dsp_coeff_read_ctrl() and cs_dsp_coeff_write_ctrl().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160250.3700346-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the logging of each algorithm from info level to debug level.
On the original devices supported by this code there were typically only
one or two algorithms in a firmware and one or two DSPs so this logging
only used a small number of log lines.
However, for the latest devices there could be 30-40 algorithms in a
firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log
for information that isn't particularly important to have logged.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.
If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:
1) After cs42l42_sdw_probe() returns the thread that called it
will call cs42l42_sdw_update_status() to report the last
status recorded by the SoundWire core.
2) The SoundWire bus master will see a PING with the CS42L42
now reporting as unenumerated and will trigger the core
SoundWire code to start enumerating CS42L42.
These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.
To avoid this race condition:
- Leave RESET asserted on exit from cs42l42_sdw_probe().
This ensures that an UNATTACHED notification must be
sent to the cs42l42 driver. If cs42l42 was already
enumerated it will be seen to drop off the bus, causing
an UNATTACH notification. If it was never enumerated the
status is already UNATTACHED and this will be reported
by thread (1).
- When the UNATTACH notification is received, release RESET.
This will cause CS42L42 to be enumerated and eventually
report an ATTACHED notification.
- The ATTACHED notification is now valid.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.
Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L42 can accept very short reset pulses of a few microseconds
but there's no reason to force a very short pulse.
Allow a wide range for the usleep_range() so it can be relaxed about
the choice of timing source.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Hans de Goede <hdegoede@redhat.com>:
The recent(ish) rt5640 changes to add HDA header jack-detect support
and the related suspend/resume handling fixes have introduced several
issues with IRQ handling on boards not using the HDA header jack-detect
support.
This series fixes these issues, see the individual commit messages
for details.
Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI and SoundWire.
Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.
THIS WILL NOT APPLY CLEANLY TO 6.5 AND EARLIER:
We will send a separate backport patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912133841.3480466-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If jack-detection is not used; or has already been disabled then
there is no need to call rt5640_cancel_work().
Move the rt5640_cancel_work() inside the "if (rt5640->jack) {}" block,
grouping it together with the disabling of the IRQ which queues the work
in the first place.
This also makes suspend() symetrical with resume() which re-queues the work
in an "if (rt5640->jack) {}" block.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set "rt5640->irq_requested = true" after a successful request_irq()
in rt5640_enable_hda_jack_detect(), so that rt5640_disable_jack_detect()
properly frees the IRQ.
This fixes the IRQ not being freed on rmmod / driver unbind.
Fixes: 2b9c8d2b3c ("ASoC: rt5640: Add the HDA header support")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The jack-detect IRQ should be enabled *after* the jack-detect related
configuration registers have been programmed.
Move the enable_irq() call for this to after the register setup.
Fixes: 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When jack-detect was originally added disabling the IRQ during suspend
was done by the sound/soc/intel/boards/bytcr_rt5640.c driver
calling snd_soc_component_set_jack(NULL) on suspend, which calls
rt5640_disable_jack_detect(), which calls free_irq() which also
disables it.
Commit 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
added disable_irq() / enable_irq() calls on suspend/resume for machine
drivers which do not call snd_soc_component_set_jack(NULL) on suspend.
The new disable_irq() / enable_irq() are made conditional by
"if (rt5640->irq)" statements, but this is true for the machine drivers
which do call snd_soc_component_set_jack(NULL) on suspend too, causing
a disable_irq() call there on the already free-ed IRQ.
Change the "if (rt5640->irq)" condition to "if (rt5640->jack)" to fix this,
rt5640->jack is only set if the jack-detect IRQ handler is still active
when rt5640_suspend() runs.
And adjust rt5640_enable_hda_jack_detect()'s request_irq() error handling
to set rt5640->jack to NULL to match (note that the old setting of irq to
-ENOXIO still resulted in disable_irq(-ENOXIO) calls on suspend).
Fixes: 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:
BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
preempt_count: 10001, expected: 0
RCU nest depth: 0, expected: 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
---[ end trace ad1c64905aac14a6 ]-
The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().
The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
avoiding the sleep in atomic context.
Fixes: 051dade346 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Reported-by: Sameer Pujar <spujar@nvidia.com>
Closes: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 70a6404ff6 ("ASoC: rt5640: Fix sleep in atomic context")
not only switched from request_irq() to request_threaded_irq(),
to fix the sleep in atomic context issue, but it also added
devm management of the IRQ by actually switching to
devm_request_threaded_irq() (without any explanation in the commit
message for this change).
This is wrong since the IRQ was already explicitly managed by
the driver. On unbind the ASoC core will call rt5640_set_jack(NULL)
which in turn will call rt5640_disable_jack_detect() which
frees the IRQ already. So now we have a double free.
Besides the unexplained switch to devm being wrong, the actual fix
for the sleep in atomic context issue also is not the best solution.
The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
which does not sleep. Using mod_delayed_work() is a much better fix
then adding a thread which does nothing other then queuing a work-item.
This patch is a straight revert of the troublesome changes, the switch
to mod_delayed_work() is done in a separate follow-up patch.
Fixes: 70a6404ff6 ("ASoC: rt5640: Fix sleep in atomic context")
Cc: Sameer Pujar <spujar@nvidia.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Sameer Pujar <spujar@nvidia.com>:
This small series fixes redundant PLLA updates that happen for
each DAI link in the audio path. This helps to resolve DMIC clock
issue seen on Jetson TX2 platform.
The rpmsg pcm device is a device which should support
double buffering.
Found this issue with pipewire. When there is no
SNDRV_PCM_INFO_BATCH flag in driver, the pipewire will
set headroom to be zero, and because rpmsg pcm device
don't support residue report, when the latency setting
is small, the "delay" always larger than "target" in
alsa-pcm.c, that reading next period data is not
scheduled on time.
With SNDRV_PCM_INFO_BATCH flag in driver, the pipewire
will select a smaller period size for device, then
the task of reading next period data will be scheduled
on time.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1694414287-13291-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ac950278b0 ("ASoC: add N cpus to M codecs dai link support")
added an additional local params in __soc_pcm_hw_params, for the CPU
side of the DAI. The snd_pcm_hw_params struct is pretty large (604
bytes) and keeping two local copies of it can make the stack frame
really large.
It is worth noting the variables are in separate code blocks so for
some optimisation levels in the compiler these will get automatically
combined keeping the stack frame reasonable. But better to manually
combine them to cover all cases.
Add a single local variable for __soc_pcm_hw_params and use in both
loops to shrink the stack frame.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908085920.2906359-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 422f10adc3 ("ASoC: wm8960: Add support for the power supplies")
added regulator support to the wm8960 driver, but neglected to update
error handling in the probe function. This results in warning backtraces
if the probe function fails.
Fixes: 422f10adc3 ("ASoC: wm8960: Add support for the power supplies")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230909120237.2646275-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230907095521.14053-11-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
For spdif input to report the locked rate correctly, even when no capture
is running, the HW and reference clock must be started as soon as
the dai is probed.
Fixes: 5ce5658375 ("ASoC: meson: add axg spdif input")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230907090504.12700-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver remove() must call pm_runtime_dont_use_autosuspend().
Drivers that call pm_runtime_use_autosuspend() must disable
it in driver remove(). Unfortunately until recently this was
only mentioned in 1 line in a 900+ line document so most
people hadn't noticed this. It has only recently been added
to the kerneldoc of pm_runtime_use_autosuspend().
THIS WON'T APPLY CLEANLY TO V6.5 AND EARLIER:
We will send a separate backported patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908101716.2658582-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra audio graph card has many DAI links which connects internal
AHUB modules and external audio codecs. Since these are DPCM links,
hw_params() call in the machine driver happens for each connected
BE link and PLLA is updated every time. This is not really needed
for all links as only I/O link DAIs derive respective clocks from
PLLA_OUT0 and thus from PLLA. Hence add checks to limit the clock
updates to DAIs over I/O links.
This found to be fixing a DMIC clock discrepancy which is suspected
to happen because of back to back quick PLLA and PLLA_OUT0 rate
updates. This was observed on Jetson TX2 platform where DMIC clock
ended up with unexpected value.
Fixes: 202e2f7745 ("ASoC: tegra: Add audio graph based card driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1694098945-32760-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add CI integration support files for drm subsystem to gitlab.freedesktop.org instance.
-----BEGIN PGP SIGNATURE-----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=X1RZ
-----END PGP SIGNATURE-----
Merge tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm ci scripts from Dave Airlie:
"This is a bunch of ci integration for the freedesktop gitlab instance
where we currently do upstream userspace testing on diverse sets of
GPU hardware. From my perspective I think it's an experiment worth
going with and seeing how the benefits/noise playout keeping these
files useful.
Ideally I'd like to get this so we can do pre-merge testing on PRs
eventually.
Below is some info from danvet on why we've ended up making the
decision and how we can roll it back if we decide it was a bad plan.
Why in upstream?
- like documentation, testcases, tools CI integration is one of these
things where you can waste endless amounts of time if you
accidentally have a version that doesn't match your source code
- but also like the above, there's a balance, this is the initial cut
of what we think makes sense to keep in sync vs out-of-tree,
probably needs adjustment
- gitlab supports out-of-repo gitlab integration and that's what's
been used for the kernel in drm, but it results in per-driver
fragmentation and lots of duplicated effort. the simple act of
smashing an arbitrary winner into a topic branch already started
surfacing patches on dri-devel and sparking good cross driver team
discussions
Why gitlab?
- it's not any more shit than any of the other CI
- drm userspace uses it extensively for everything in userspace, we
have a lot of people and experience with this, including
integration of hw testing labs
- media userspace like gstreamer is also on gitlab.fd.o, and there's
discussion to extend this to the media subsystem in some fashion
Can this be shared?
- there's definitely a pile of code that could move to scripts/ if
other subsystem adopt ci integration in upstream kernel git. other
bits are more drm/gpu specific like the igt-gpu-tests/tools
integration
- docker images can be run locally or in other CI runners
Will we regret this?
- it's all in one directory, intentionally, for easy deletion
- probably 1-2 years in upstream to see whether this is worth it or a
Big Mistake. that's roughly what it took to _really_ roll out solid
CI in the bigger userspace projects we have on gitlab.fd.o like
mesa3d"
* tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm:
drm: ci: docs: fix build warning - add missing escape
drm: Add initial ci/ subdirectory
