Recall that the primary role of the cxl_mem driver is to probe if the
given endpoint is connected to a CXL port topology. In that process it
walks its device ancestry to its PCI root port. If that root port is
also a CXL root port then the probe process adds cxl_port object
instances at switch in the path between to the root and the endpoint. As
those cxl_port instances are added, or if a previous enumeration
attempt already created the port, a 'struct cxl_ep' instance is
registered with that port to track the endpoints interested in that
port.
At the time the cxl_ep is registered the downstream egress path from the
port to the endpoint is known. Take the opportunity to record that
information as it will be needed for dynamic programming of decoder
targets during region provisioning.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784329944.1758207.15203961796832072116.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The region provisioning flow will roughly follow a sequence of:
1/ Allocate DPA to a set of decoders
2/ Allocate HPA to a region
3/ Associate decoders with a region and validate that the DPA allocations
and topologies match the parameters of the region.
For now, this change (step 1) arranges for DPA capacity to be allocated
and deleted from non-committed decoders based on the decoder's mode /
partition selection. Capacity is allocated from the lowest DPA in the
partition and any 'pmem' allocation blocks out all remaining ram
capacity in its 'skip' setting. DPA allocations are enforced in decoder
instance order. I.e. decoder N + 1 always starts at a higher DPA than
instance N, and deleting allocations must proceed from the
highest-instance allocated decoder to the lowest.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784329399.1758207.16732038126938632700.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The CXL specification enforces that endpoint decoders are committed in
hw instance id order. In preparation for adding dynamic DPA allocation,
record the hw instance id in endpoint decoders, and enforce allocations
to occur in hw instance id order.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784328827.1758207.9627538529944559954.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Recall that the Device Physical Address (DPA) space of a CXL Memory
Expander is potentially partitioned into a volatile and persistent
portion. A decoder maps a Host Physical Address (HPA) range to a DPA
range and that translation depends on the value of all previous (lower
instance number) decoders before the current one.
In preparation for allowing dynamic provisioning of regions, decoders
need an ABI to indicate which DPA partition a decoder targets. This ABI
needs to be prepared for the possibility that some other agent committed
and locked a decoder that spans the partition boundary.
Add 'decoderX.Y/mode' to endpoint decoders that indicates which
partition 'ram' / 'pmem' the decoder targets, or 'mixed' if the decoder
currently spans the partition boundary.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603881967.551046.6007594190951596439.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for provisioning CXL regions, add accounting for the DPA
space consumed by existing regions / decoders. Recall, a CXL region is a
memory range comprised from one or more endpoint devices contributing a
mapping of their DPA into HPA space through a decoder.
Record the DPA ranges covered by committed decoders at initial probe of
endpoint ports relative to a per-device resource tree of the DPA type
(pmem or volatile-ram).
The cxl_dpa_rwsem semaphore is introduced to globally synchronize DPA
state across all endpoints and their decoders at once. The vast majority
of DPA operations are reads as region creation is expected to be as rare
as disk partitioning and volume creation. The device_lock() for this
synchronization is specifically avoided for concern of entangling with
sysfs attribute removal.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784327682.1758207.7914919426043855876.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously the target routing specifics of switch decoders and platform
CXL window resource tracking of root decoders were factored out of
'struct cxl_decoder'. While switch decoders translate from SPA to
downstream ports, endpoint decoders translate from SPA to DPA.
This patch, 3 of 3, adds a 'struct cxl_endpoint_decoder' that tracks an
endpoint-specific Device Physical Address (DPA) resource. For now this
just defines ->dpa_res, a follow-on patch will handle requesting DPA
resource ranges from a device-DPA resource tree.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784327088.1758207.15502834501671201192.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously the target routing specifics of switch decoders were factored
out of 'struct cxl_decoder' into 'struct cxl_switch_decoder'.
This patch, 2 of 3, adds a 'struct cxl_root_decoder' as a superset of a
switch decoder that also track the associated CXL window platform
resource.
Note that the reason the resource for a given root decoder needs to be
looked up after the fact (i.e. after cxl_parse_cfmws() and
add_cxl_resource()) is because add_cxl_resource() may have merged CXL
windows in order to keep them at the top of the resource tree / decode
hierarchy.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784326541.1758207.9915663937394448341.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently 'struct cxl_decoder' contains the superset of attributes
needed for all decoder types. Before more type-specific attributes are
added to the common definition, reorganize 'struct cxl_decoder' into type
specific objects.
This patch, the first of three, factors out a cxl_switch_decoder type.
See the new kdoc for what a 'struct cxl_switch_decoder' represents in a
CXL topology.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/165784325340.1758207.5064717153608954960.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The per-device CDAT data provides performance data that is relevant for
mapping which CXL devices can participate in which CXL ranges by QTG
(QoS Throttling Group) (per ECN: CXL 2.0 CEDT CFMWS & QTG_DSM) [1]. The
QTG association specified in the ECN is advisory. Until the
cxl_acpi driver grows support for invoking the QTG _DSM method the CDAT
data is only of interest to userspace that may need it for debug
purposes.
Search the DOE mailboxes available, query CDAT data, cache the data and
make it available via a sysfs binary attribute per endpoint at:
/sys/bus/cxl/devices/endpointX/CDAT
...similar to other ACPI-structured table data in
/sys/firmware/ACPI/tables. The CDAT is relative to 'struct cxl_port'
objects since switches in addition to endpoints can host a CDAT
instance. Switch CDAT support is not implemented.
This does not support table updates at runtime. It will always provide
whatever was there when first cached. It is also the case that table
updates are not expected outside of explicit DPA address map affecting
commands like Set Partition with the immediate flag set. Given that the
driver does not support Set Partition with the immediate flag set there
is no current need for update support.
Link: https://www.computeexpresslink.org/spec-landing [1]
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
[djbw: drop in-kernel parsing infra for now, and other minor fixups]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220719205249.566684-7-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Unless and until accelerator (type-2) drivers start registering for
CXL.mem mapping services from the CXL subsystem core, initialize idle
HDM decoders to the "expander" type. I.e. the only CXL devices using the
CXL core presently are those implementing the CXL 2.0 Type-3 memory
expander device class code that the cxl_pci driver claims.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-6-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Region creation has need for checking host-bridge connectivity when
adding endpoints to regions. Record, at port creation time, the
host-bridge to provide a useful shortcut from any location in the
topology to the most-significant ancestor.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-4-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In support of testing DPA allocation mechanisms in the CXL core, the
cxl_test environment needs to support establishing and retrieving the
'pmem partition boundary.
Replace the platform_device_add_resources() method for delineating DPA
within an endpoint with an emulated DEV_SIZE amount of partitionable
capacity. Set DEV_SIZE such that an endpoint has enough capacity to
simultaneously participate in 8 distinct regions.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603887411.551046.13234212587991192347.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dump the device-physical-address map for a CXL expander in /proc/iomem
style format. E.g.:
cat /sys/kernel/debug/cxl/mem1/dpamem
00000000-0fffffff : ram
10000000-1fffffff : pmem
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603885318.551046.8308248564880066726.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for a new cxl debugfs file, move 'cxl' directory
establishment and teardown to the core and let subsequent init routines
reference that setup.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603884654.551046.4962104601691723080.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for region provisioning all device decoders need to be
enumerated since DPA allocations are calculated by summing the
capacities of all decoders in a set. I.e. the programming for decoder[N]
depends on the state of decoder[N-1], so skipping over decoders that
fail to initialize prevents accurate DPA accounting.
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
[djbw: reword changelog]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603879664.551046.6863805202478861026.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To date the per-device-partition DPA range information has only been
used for enumeration purposes. In preparation for allocating regions
from available DPA capacity, convert those ranges into DPA-type resource
trees.
With resources and the new add_dpa_res() helper some open coded end
address calculations and debug prints can be cleaned.
The 'cxlds->pmem_res' and 'cxlds->ram_res' resources are child resources
of the total-device DPA space and they in turn will host DPA allocations
from cxl_endpoint_decoder instances (tracked by cxled->dpa_res).
Cc: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603878921.551046.8127845916514734142.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Interleave granularity and ways have CXL specification defined encodings.
Promote the conversion helpers to a common header, and use them to
replace other open-coded instances.
Force caller to consider the error case of the conversion similarly to
other conversion helpers like kstrto*().
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603875016.551046.17236943065932132355.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This helper was only used to identify the object type for lockdep
purposes. Now that lockdep support is done with explicit lock classes,
this helper can be dropped.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603874340.551046.15491766127759244728.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Root decoders are responsible for hosting the available host address
space for endpoints and regions to claim. The tracking of that available
capacity can be done in iomem_resource directly. As a result, root
decoders no longer need to host their own resource tree. The
current ->platform_res attribute was added prematurely.
Otherwise, ->hpa_range fills the role of conveying the current decode
range of the decoder.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603873619.551046.791596854070136223.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for growing a ->dpa_range attribute for endpoint
decoders, rename the current ->decoder_range to the more descriptive
->hpa_range.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603872867.551046.2170426227407458814.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Save a few characters and use the already initialized local variable.
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603872171.551046.913207574344536475.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The upcoming region provisioning implementation has a need to
dereference port->uport during the port unregister flow. Specifically,
endpoint decoders need to be able to lookup their corresponding memdev
via port->uport.
The existing ->dead flag was added for cases where the core was
committed to tearing down the port, but needed to drop locks before
calling device_unregister(). Reuse that flag to indicate to
delete_endpoint() that it has no "release action" work to do as
unregister_port() will handle it.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603871491.551046.6682199179541194356.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The conversion of command sizes to unsigned missed a couple of checks
against variable size payloads during command validation, which made all
variable payload commands unconditionally fail. Add the checks back using
the new CXL_VARIABLE_PAYLOAD scheme.
Fixes: 26f89535a5 ("cxl/mbox: Use type __u32 for mailbox payload sizes")
Cc: <stable@vger.kernel.org>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Reported-by: Abhi Cs <abhi.cs@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20220628220109.633564-1-vishal.l.verma@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Save some characters and directly check decoder type rather than port
type. There's no need to check if the port is an endpoint port since, by
this point, cxl_endpoint_decoder_alloc() has a specified type.
Reviewed by: Adam Manzanares <a.manzanares@samsung.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL memory expanders that support the CXL 2.0 memory device class code
include an "HDM Decoder Capability" mechanism to supplant the "CXL DVSEC
Range" mechanism originally defined in CXL 1.1. Both mechanisms depend
on a "mem_enable" bit being set in configuration space before either
mechanism activates. When the HDM Decoder Capability is enabled the CXL
DVSEC Range settings are ignored.
Previously, the cxl_mem driver was relying on platform-firmware to set
"mem_enable". That is an invalid assumption as there is no requirement
that platform-firmware sets the bit before the driver sees a device,
especially in hot-plug scenarios. Additionally, ACPI-platforms that
support CXL 2.0 devices also support the ACPI CEDT (CXL Early Discovery
Table). That table outlines the platform permissible address ranges for
CXL operation. So, there is a need for the driver to set "mem_enable",
and there is information available to determine the validity of the CXL
DVSEC Ranges.
Arrange for the driver to optionally enable the HDM Decoder Capability
if "mem_enable" was not set by platform firmware, or the CXL DVSEC Range
configuration was invalid. Be careful to only disable memory decode if
the kernel was the one to enable it. In other words, if CXL is backing
all of kernel memory at boot the device needs to maintain "mem_enable"
and "HDM Decoder enable" all the way up to handoff back to platform
firmware (e.g. ACPI S5 state entry may require CXL memory to stay
active).
Fixes: 560f785590 ("cxl/pci: Retrieve CXL DVSEC memory info")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
[dan: fix early terminiation of range-allowed loop]
Cc: Ariel Sibley <ariel.sibley@microchip.com>
[ariel: Memory_size must be non-zero]
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/165307136375.2499769.861793697156744166.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The port driver maps component registers for port operations. Reuse that
mapping for HDM Decoder Capability setup / enable. Move
devm_cxl_setup_hdm() before cxl_hdm_decode_init() and plumb @cxlhdm
through the hdm init helpers.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165291691712.1426646.14336397551571515480.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that nothing external to cxl_hdm_decode_init() considers
'struct cxl_endpoint_dvec_info' move it internal to
cxl_hdm_decode_init().
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165291690612.1426646.7866084245521113414.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for changing how the driver handles 'mem_enable' in the CXL
DVSEC control register. Merge the contents of cxl_hdm_decode_init() into
cxl_dvsec_ranges() and rename the combined function cxl_hdm_decode_init().
The possible cleanups and fixes that result from this merge are saved for a
follow-on change.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/165291690027.1426646.10249756632415633752.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a device does not have mem_enable set then the current range
settings are moot. Skip the enumeration and cause cxl_hdm_decode_init()
to proceed directly to enable the HDM Decoder Capability.
Fixes: 560f785590 ("cxl/pci: Retrieve CXL DVSEC memory info")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165291689442.1426646.18012291761753694336.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for fixing the setting of the 'mem_enabled' bit in CXL
DVSEC Control register, move all CXL DVSEC range enumeration into the
same source file.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165291688886.1426646.15046138604010482084.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allow cxl_await_media_ready() to be mocked for testing purposes rather
than carrying the maintenance burden of an indirect function call in the
mainline driver.
With the move cxl_await_media_ready() can no longer reuse the mailbox
timeout override, so add a media_ready_timeout module parameter to the
core to backfill.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165291688340.1426646.4755627801983775011.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all CXL subsystem locking is validated with custom lock
classes, there is no need for the custom usage of the lockdep_mutex.
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Ben Widawsky <ben.widawsky@intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/165055520383.3745911.53447786039115271.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In response to an attempt to expand dev->lockdep_mutex for device_lock()
validation [1], Peter points out [2] that the lockdep API already has
the ability to assign a dedicated lock class per subsystem device-type.
Use lockdep_set_class() to override the default device_lock()
'__lockdep_no_validate__' class for each CXL subsystem device-type. This
enables lockdep to detect deadlocks and recursive locking within the
device-driver core and the subsystem. The
lockdep_set_class_and_subclass() API is used for port objects that
recursively lock the 'cxl_port_key' class by hierarchical topology
depth.
Link: https://lore.kernel.org/r/164982968798.684294.15817853329823976469.stgit@dwillia2-desk3.amr.corp.intel.com [1]
Link: https://lore.kernel.org/r/Ylf0dewci8myLvoW@hirez.programming.kicks-ass.net [2]
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Ben Widawsky <ben.widawsky@intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/165055519317.3745911.7342499516839702840.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This should be bitwise & instead of &&.
Fixes: 6179045ccc ("cxl/mbox: Block immediate mode in SET_PARTITION_INFO command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YmpgkbbQ1Yxu36uO@kili
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
vmemdup_user() returns an ERR_PTR() on failure. Use IS_ERR()
to check the return value.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/20220407010915.1211258-1-alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Payload sizes for mailbox commands are expected to be positive values
coming from userspace. The documentation correctly describes these as
always unsigned values. The mailbox and send structures that support
the mailbox commands however, use __s32 types for the payloads.
Replace __s32 with __u32 in the mailbox and send command structures
and update usages.
Kernel users of the interface already block all negative values and
there is no known ability for userspace to have grown a dependency on
submitting negative values to the kernel. The known user of the IOCTL,
the CXL command line interface (cxl-cli) already enforces positive
size values.
A Smatch warning of a signedness uncovered this issue.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Link: https://lore.kernel.org/r/20220414051246.1244575-1-alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The CXL specification claims S3 support at a hardware level, but at a
system software level there are some missing pieces. Section 9.4 (CXL
2.0) rightly claims that "CXL mem adapters may need aux power to retain
memory context across S3", but there is no enumeration mechanism for the
OS to determine if a given adapter has that support. Moreover the save
state and resume image for the system may inadvertantly end up in a CXL
device that needs to be restored before the save state is recoverable.
I.e. a circular dependency that is not resolvable without a third party
save-area.
Arrange for the cxl_mem driver to fail S3 attempts. This still nominaly
allows for suspend, but requires unbinding all CXL memory devices before
the suspend to ensure the typical DRAM flow is taken. The cxl_mem unbind
flow is intended to also tear down all CXL memory regions associated
with a given cxl_memdev.
It is reasonable to assume that any device participating in a System RAM
range published in the EFI memory map is covered by aux power and
save-area outside the device itself. So this restriction can be
minimized in the future once pre-existing region enumeration support
arrives, and perhaps a spec update to clarify if the EFI memory map is
sufficent for determining the range of devices managed by
platform-firmware for S3 support.
Per Rafael, if the CXL configuration prevents suspend then it should
fail early before tasks are frozen, and mem_sleep should stop showing
'mem' as an option [1]. Effectively CXL augments the platform suspend
->valid() op since, for example, the ACPI ops are not aware of the CXL /
PCI dependencies. Given the split role of platform firmware vs OS
provisioned CXL memory it is up to the cxl_mem driver to determine if
the CXL configuration has elements that platform firmware may not be
prepared to restore.
Link: https://lore.kernel.org/r/CAJZ5v0hGVN_=3iU8OLpHY3Ak35T5+JcBM-qs8SbojKrpd0VXsA@mail.gmail.com [1]
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/165066828317.3907920.5690432272182042556.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the global cxl_mbox_cmd_rc table to improve debug messaging
in __cxl_pci_mbox_send_cmd() and allow cxl_mbox_send_cmd()
to map to proper kernel style errno codes - this patch
continues to use -ENXIO only so no change in semantics.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/20220404021216.66841-5-dave@stgolabs.net
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Upon a completed command the caller is still expected to check
the actual return_code register to ensure it succeed. This
adds, per the spec, the potential command return codes. It maps
the hardware return code with the kernel's errno style, and by
default continues to use -ENXIO (Command completed, but device
reported an error).
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/20220404021216.66841-4-dave@stgolabs.net
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
... we have lockdep for this.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/20220404021216.66841-2-dave@stgolabs.net
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
User space may send the SET_PARTITION_INFO mailbox command using
the IOCTL interface. Inspect the input payload and fail if the
immediate flag is set.
This is the first instance of the driver inspecting an input payload
from user space. Assume there will be more such cases and implement
with an extensible helper.
In order for the kernel to react to an immediate partition change it
needs to assert that the change will not affect any active decode. At
a minimum this requires validating that the device is using HDM
decoders instead of the CXL DVSEC for decode, and that none of the
active HDM decoders are affected by the partition change. For now,
just fail until that support arrives.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/241821186c363833980adbc389e2c547bc5a6395.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
cxl_validate_command_from_user() is now the single point of validation
for mailbox commands coming from user space. Previously, it returned a
a cxl_mem_command, but that was not sufficient when validation of the
actual mailbox command became a requirement. Now, it returns a fully
validated cxl_mbox_cmd.
Remove the extraneous cxl_mem_command parameter. Define and use a
local version only.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/c11a437896d914daf36f5ac8ec62f999c5ec2da7.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously, handle_mailbox_cmd_from_user(), constructed the mailbox
command and dispatched it to the hardware. The construction work
has moved to the validation path.
handle_mailbox_cmd_from_user() now expects a fully validated
mbox param. Make it's caller, cxl_send_cmd(), deliver it. Update
the comments and dereferencing of the new mbox parameter.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/77050ba512d6c30eccf7505467509e460dd325a0.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for removing access to struct cxl_mem_command,
change this debug message to use cxl_mbox_cmd fields instead.
Retrieve the pretty command name from cxl_mbox_cmd using a new
opcode to command name helper.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/57265751d336a6e95f5ca31a9c77189408b05742.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a step in refactoring the handling of user space mailbox
commands. The intent is to have all the validation work originate
in cxl_validate_cmd_from_user().
Move the construction and validation of a mailbox command to the
validation path. Continue to pass both the out_cmd and the mbox_cmd
until handle_mbox_cmd_from_user() learns how to use a mbox_cmd param.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/c9fbdad968a2b619f9108bb6c37cef1a853cdf5a.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This move serves two purposes: 1) Emit the warning in the raw
command validation path, and 2) Remove the dependency on the
struct cxl_mem_command in handle_mailbox_cmd_from_user() in
preparation for a refactor of that function.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/df5f0e0ec8afa1f75299aa86b4226ab4479ef325.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Sanitizing and constructing a cxl_mem_command from a userspace
command is part of the validation process prior to submitting
the command to a CXL device. Move this work to helper functions:
cxl_to_mem_cmd(), cxl_to_mem_cmd_raw().
This declutters cxl_validate_cmd_from_user() in preparation for
adding new validation steps.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/7d9b826f29262e3a484cb4bb7b63872134d60bd7.1648687552.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix the following coccicheck warning:
./drivers/cxl/core/port.c:913:21-24: ERROR: port is NULL but dereferenced.
The put_device() is only relevent in the is_cxl_root() case.
Fixes: 2703c16c75 ("cxl/core/port: Add switch port enumeration")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20220307094158.404882-1-wanjiabing@vivo.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
KASAN + DEBUG_KOBJECT_RELEASE reports a potential use-after-free in
cxl_decoder_release() where it goes to reference its parent, a cxl_port,
to free its id back to port->decoder_ida.
BUG: KASAN: use-after-free in to_cxl_port+0x18/0x90 [cxl_core]
Read of size 8 at addr ffff888119270908 by task kworker/35:2/379
CPU: 35 PID: 379 Comm: kworker/35:2 Tainted: G OE 5.17.0-rc2+ #198
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: events kobject_delayed_cleanup
Call Trace:
<TASK>
dump_stack_lvl+0x59/0x73
print_address_description.constprop.0+0x1f/0x150
? to_cxl_port+0x18/0x90 [cxl_core]
kasan_report.cold+0x83/0xdf
? to_cxl_port+0x18/0x90 [cxl_core]
to_cxl_port+0x18/0x90 [cxl_core]
cxl_decoder_release+0x2a/0x60 [cxl_core]
device_release+0x5f/0x100
kobject_cleanup+0x80/0x1c0
The device core only guarantees parent lifetime until all children are
unregistered. If a child needs a parent to complete its ->release()
callback that child needs to hold a reference to extend the lifetime of
the parent.
Fixes: 40ba17afdf ("cxl/acpi: Introduce cxl_decoder objects")
Reported-by: Ben Widawsky <ben.widawsky@intel.com>
Tested-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/164505751190.4175768.13324905271463416712.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
