Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050a ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On unloading of the scmi_perf_domain module got the below splat, when in
the DT provided to the system under test the '#power-domain-cells' property
was missing. Indeed, this particular setup causes the probe to bail out
early without giving any error, which leads to the ->remove() callback gets
to run too, but without all the expected initialized structures in place.
Add a check and bail out early on remove too.
Call trace:
scmi_perf_domain_remove+0x28/0x70 [scmi_perf_domain]
scmi_dev_remove+0x28/0x40 [scmi_core]
device_remove+0x54/0x90
device_release_driver_internal+0x1dc/0x240
driver_detach+0x58/0xa8
bus_remove_driver+0x78/0x108
driver_unregister+0x38/0x70
scmi_driver_unregister+0x28/0x180 [scmi_core]
scmi_perf_domain_driver_exit+0x18/0xb78 [scmi_perf_domain]
__arm64_sys_delete_module+0x1a8/0x2c0
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0x100/0x130
el0t_64_sync+0x190/0x198
Code: a90153f3 f9403c14 f9414800 955f8a05 (b9400a80)
---[ end trace 0000000000000000 ]---
Fixes: 2af23ceb86 ("pmdomain: arm: Add the SCMI performance domain")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240125191756.868860-1-cristian.marussi@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the power domains are registered first with genpd and *after that*
the driver attempts to power them on in the probe sequence, then it is
possible that a race condition occurs if genpd tries to power them on
in the same time.
The same is valid for powering them off before unregistering them
from genpd.
Attempt to fix race conditions by first removing the domains from genpd
and *after that* powering down domains.
Also first power up the domains and *after that* register them
to genpd.
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231225133615.78993-1-eugen.hristev@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power domain containing the Cortex-R7 CPU core on the R-Car V3H SoC
must always be in power-on state, unlike on other SoCs in the R-Car Gen3
family. See Table 9.4 "Power domains" in the R-Car Series, 3rd
Generation Hardware User’s Manual Rev.1.00 and later.
Fix this by marking the domain as a CPU domain without control
registers, so the driver will not touch it.
Fixes: 41d6d8bd8a ("soc: renesas: rcar-sysc: add R8A77980 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/fdad9a86132d53ecddf72b734dac406915c4edc0.1705076735.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The unused clock cleanup uses the _sync initcall to give all users at
earlier initcalls time to probe. Do the same to avoid leaving some PDs
dangling at "on" (which actually happened on qcom!).
Fixes: 2fe71dcdfd ("PM / domains: Add late_initcall to disable unused PM domains")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231227-topic-pmdomain_sync_cleanup-v1-1-5f36769d538b@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here are the set of driver core and kernfs changes for 6.8-rc1. Nothing
major in here this release cycle, just lots of small cleanups and some
tweaks on kernfs that in the very end, got reverted and will come back
in a safer way next release cycle.
Included in here are:
- more driver core 'const' cleanups and fixes
- fw_devlink=rpm is now the default behavior
- kernfs tiny changes to remove some string functions
- cpu handling in the driver core is updated to work better on many
systems that add topologies and cpus after booting
- other minor changes and cleanups
All of the cpu handling patches have been acked by the respective
maintainers and are coming in here in one series. Everything has been
in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeOrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymtcwCffzvKKkSY9qAp6+0v2WQNkZm1JWoAoJCPYUwF
If6wEoPLWvRfKx4gIoq9
=D96r
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the set of driver core and kernfs changes for 6.8-rc1.
Nothing major in here this release cycle, just lots of small cleanups
and some tweaks on kernfs that in the very end, got reverted and will
come back in a safer way next release cycle.
Included in here are:
- more driver core 'const' cleanups and fixes
- fw_devlink=rpm is now the default behavior
- kernfs tiny changes to remove some string functions
- cpu handling in the driver core is updated to work better on many
systems that add topologies and cpus after booting
- other minor changes and cleanups
All of the cpu handling patches have been acked by the respective
maintainers and are coming in here in one series. Everything has been
in linux-next for a while with no reported issues"
* tag 'driver-core-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (51 commits)
Revert "kernfs: convert kernfs_idr_lock to an irq safe raw spinlock"
kernfs: convert kernfs_idr_lock to an irq safe raw spinlock
class: fix use-after-free in class_register()
PM: clk: make pm_clk_add_notifier() take a const pointer
EDAC: constantify the struct bus_type usage
kernfs: fix reference to renamed function
driver core: device.h: fix Excess kernel-doc description warning
driver core: class: fix Excess kernel-doc description warning
driver core: mark remaining local bus_type variables as const
driver core: container: make container_subsys const
driver core: bus: constantify subsys_register() calls
driver core: bus: make bus_sort_breadthfirst() take a const pointer
kernfs: d_obtain_alias(NULL) will do the right thing...
driver core: Better advertise dev_err_probe()
kernfs: Convert kernfs_path_from_node_locked() from strlcpy() to strscpy()
kernfs: Convert kernfs_name_locked() from strlcpy() to strscpy()
kernfs: Convert kernfs_walk_ns() from strlcpy() to strscpy()
initramfs: Expose retained initrd as sysfs file
fs/kernfs/dir: obey S_ISGID
kernel/cgroup: use kernfs_create_dir_ns()
...
- Move the generic PM domain and its governor to the pmdomain subsystem
- Drop the unused pm_genpd_opp_to_performance_state()
Providers:
- Convert some providers to let the ->remove() callback return void
- amlogic: Add support for G12A ISP power domain
- arm: Move the SCPI power-domain driver to the pmdomain subsystem
- arm: Move Kconfig options to the pmdomain subsystem
- qcom: Update part number to X1E80100 for the rpmhpd
-----BEGIN PGP SIGNATURE-----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=xSMR
-----END PGP SIGNATURE-----
Merge tag 'pmdomain-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"Core:
- Move the generic PM domain and its governor to the pmdomain
subsystem
- Drop the unused pm_genpd_opp_to_performance_state()
Providers:
- Convert some providers to let the ->remove() callback return void
- amlogic: Add support for G12A ISP power domain
- arm: Move the SCPI power-domain driver to the pmdomain subsystem
- arm: Move Kconfig options to the pmdomain subsystem
- qcom: Update part number to X1E80100 for the rpmhpd"
* tag 'pmdomain-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
PM: domains: Move genpd and its governor to the pmdomain subsystem
PM: domains: Drop redundant header for genpd
PM: domains: Drop the unused pm_genpd_opp_to_performance_state()
PM: domains: fix domain_governor kernel-doc warnings
pmdomain: xilinx/zynqmp: Convert to platform remove callback returning void
pmdomain: qcom-cpr: Convert to platform remove callback returning void
pmdomain: imx93-pd: Convert to platform remove callback returning void
pmdomain: imx93-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx8mp-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx8m-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx-gpcv2: Convert to platform remove callback returning void
pmdomain: imx-gpc: Convert to platform remove callback returning void
pmdomain: imx-pgc: Convert to platform remove callback returning void
pmdomain: amlogic: meson-ee-pwrc: add support for G12A ISP power domain
dt-bindings: power: meson-g12a-power: document ISP power domain
firmware: arm_scpi: Move power-domain driver to the pmdomain dir
pmdomain: arm_scmi: Move Kconfig options to the pmdomain subsystem
pmdomain: qcom: rpmhpd: Update part number to X1E80100
dt-bindings: power: rpmpd: Update part number to X1E80100
It seems reasonable to collect the core parts for the generic PM domain,
along with its corresponding provider drivers. Therefore let's move the
files from drivers/base/power/ to drivers/pmdomain/ and while at it, let's
also rename the files accordingly.
Moreover, let's also update MAINTAINERS to reflect the update.
Cc: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20231213113305.29098-1-ulf.hansson@linaro.org
- Fix the AMD P-state driver's EPP sysfs interface in the cases when the
performance governor is in use (Ayush Jain).
- Make the ->fast_switch() callback in the AMD P-state driver return the
target frequency as expected (Gautham R. Shenoy).
- Allow user space to control the range of frequencies to use via
scaling_min_freq and scaling_max_freq when AMD P-state driver is in
use (Wyes Karny).
- Prevent power domains needed for wakeup signaling from being turned
off during system suspend on Qualcomm systems and prevent performance
states votes from runtime-suspended devices from being lost across
a system suspend-resume cycle in qcom-cpufreq-nvmem (Stephan Gerhold).
- Fix disabling the 792 Mhz OPP in the imx6q cpufreq driver for the
i.MX6ULL types that can run at that frequency (Christoph Niedermaier).
- Eliminate unnecessary and harmful conversions to uW from the DTPM
(dynamic thermal and power management) framework (Lukasz Luba).
-----BEGIN PGP SIGNATURE-----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=/TF9
-----END PGP SIGNATURE-----
Merge tag 'pm-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix issues in two cpufreq drivers, in the AMD P-state driver and
in the power-capping DTPM framework.
Specifics:
- Fix the AMD P-state driver's EPP sysfs interface in the cases when
the performance governor is in use (Ayush Jain)
- Make the ->fast_switch() callback in the AMD P-state driver return
the target frequency as expected (Gautham R. Shenoy)
- Allow user space to control the range of frequencies to use via
scaling_min_freq and scaling_max_freq when AMD P-state driver is in
use (Wyes Karny)
- Prevent power domains needed for wakeup signaling from being turned
off during system suspend on Qualcomm systems and prevent
performance states votes from runtime-suspended devices from being
lost across a system suspend-resume cycle in qcom-cpufreq-nvmem
(Stephan Gerhold)
- Fix disabling the 792 Mhz OPP in the imx6q cpufreq driver for the
i.MX6ULL types that can run at that frequency (Christoph
Niedermaier)
- Eliminate unnecessary and harmful conversions to uW from the DTPM
(dynamic thermal and power management) framework (Lukasz Luba)"
* tag 'pm-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate: Only print supported EPP values for performance governor
cpufreq/amd-pstate: Fix scaling_min_freq and scaling_max_freq update
powercap: DTPM: Fix unneeded conversions to micro-Watts
cpufreq/amd-pstate: Fix the return value of amd_pstate_fast_switch()
pmdomain: qcom: rpmpd: Set GENPD_FLAG_ACTIVE_WAKEUP
cpufreq: qcom-nvmem: Preserve PM domain votes in system suspend
cpufreq: qcom-nvmem: Enable virtual power domain devices
cpufreq: imx6q: Don't disable 792 Mhz OPP unnecessarily
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231124080623.564924-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231124080623.564924-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the pmdomain fixes for v6.7-rc[n] into the next branch, to allow them
to get tested together with the changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was a mistake to prefer polling based mode when setting a performance
level for a domain. Let's instead rely on the protocol to decide what is
best and thus avoid polling when possible.
Reported-by: Nikunj Kela <nkela@quicinc.com>
Fixes: 2af23ceb86 ("pmdomain: arm: Add the SCMI performance domain")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231127135033.136442-1-ulf.hansson@linaro.org
To simplify with maintenance let's move the Arm SCPI power-domain driver
to the new pmdomain directory. Note this is different from and precedes
the new Arm SCMI protocol.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231123120847.2825444-2-sudeep.holla@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Kconfig options belongs closer to the corresponding implementations,
hence let's move them from the firmware to the pmdomain subsystem.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231123120847.2825444-1-sudeep.holla@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There was a recent part number update from SC8380XP to X1E80100 and as
a result of which SC8380xp prefix introduced in the rpmhpd driver is no
longer correct. Update it to X1E80100, to reflect the bindings change.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231123100021.10918-3-quic_sibis@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set GENPD_FLAG_ACTIVE_WAKEUP for all RPM power domains so that power
domains necessary for wakeup/"awake path" devices are kept on across
suspend.
This is needed for example for the *_AO ("active-only") variants of the
RPMPDs used by the CPU. Those should maintain their votes also across
system suspend to ensure the CPU can keep running for the whole suspend
process (ending in a firmware call). When the RPM firmware detects that
the CPUs are in a deep idle state it will drop those votes automatically.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware drivers.
- Arm FF-A firmware support gains support for v1.1 specification features,
in particular notification and memory transaction descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive, amlogic,
atmel, tegra, aspeed, vexpress, mediatek, samsung and more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper.
-----BEGIN PGP SIGNATURE-----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=QIut
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware
drivers.
- Arm FF-A firmware support gains support for v1.1 specification
features, in particular notification and memory transaction
descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive,
amlogic, atmel, tegra, aspeed, vexpress, mediatek, samsung and
more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper"
* tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (156 commits)
soc: qcom: pmic_glink_altmode: Print return value on error
firmware: qcom: scm: remove unneeded 'extern' specifiers
firmware: qcom: scm: add a missing forward declaration for struct device
firmware: qcom: move Qualcomm code into its own directory
soc: samsung: exynos-chipid: Convert to platform remove callback returning void
soc: qcom: apr: Add __counted_by for struct apr_rx_buf and use struct_size()
soc: qcom: pmic_glink: fix connector type to be DisplayPort
soc: ti: k3-socinfo: Avoid overriding return value
soc: ti: k3-socinfo: Fix typo in bitfield documentation
soc: ti: knav_qmss_queue: Use device_get_match_data()
firmware: ti_sci: Use device_get_match_data()
firmware: qcom: qseecom: add missing include guards
soc/pxa: ssp: Convert to platform remove callback returning void
soc/mediatek: mtk-mmsys: Convert to platform remove callback returning void
soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
soc/loongson: loongson2_guts: Convert to platform remove callback returning void
soc/litex: litex_soc_ctrl: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-qmgr: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-npe: Convert to platform remove callback returning void
soc/hisilicon: kunpeng_hccs: Convert to platform remove callback returning void
...
Merge the pmdomain fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new pmdomain changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without this change, the NPU hangs when the 8th NN core is used.
It matches what the out-of-tree driver does.
Signed-off-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Fixes: 9a217b7e89 ("soc: amlogic: meson-pwrc: Add NNA power domain for A311D")
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231016080205.41982-2-tomeu@tomeuvizoso.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the power domains exposed by RPMH in the Qualcomm SC8380XP platform.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231025135943.13854-4-quic_sibis@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the pmdomain fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new pmdomain changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, The imx pgc power domain doesn't set the fwnode
pointer, which results in supply regulator device can't get
consumer imx pgc power domain device from fwnode when creating
a link.
This causes the driver core to instead try to create a link
between the parent gpc device of imx pgc power domain device and
supply regulator device. However, at this point, the gpc device
has already been bound, and the link creation will fail. So adding
the fwnode pointer to the imx pgc power domain device will fix
this issue.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Fixes: 3fb16866b5 ("driver core: fw_devlink: Make cycle detection more robust")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020185949.537083-1-pengfei.li_1@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
QM215 is typically paired with a PM8916 PMIC and uses its SMPA1 and
LDOA2 regulators in voltage level mode for VDDCX and VDDMX, respectively.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231014133823.14088-4-otto.pflueger@abscue.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSM8917 uses the SMPA2 and LDOA3 regulators provided by the PM8937 PMIC
for the VDDCX and VDDMX power domains in voltage level mode,
respectively. These definitions should also work on MSM8937.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231014133823.14088-3-otto.pflueger@abscue.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit c494a447c1 ("soc: bcm: bcm2835-power: Refactor ASB control")
refactored the ASB control by using a general function to handle both
the enable and disable. But this patch introduced a subtle regression:
we need to check if !!(readl(base + reg) & ASB_ACK) == enable, not just
check if (readl(base + reg) & ASB_ACK) == true.
Currently, this is causing an invalid register state in V3D when
unloading and loading the driver, because `bcm2835_asb_disable()` will
return -ETIMEDOUT and `bcm2835_asb_power_off()` will fail to disable the
ASB slave for V3D.
Fixes: c494a447c1 ("soc: bcm: bcm2835-power: Refactor ASB control")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231024101251.6357-2-mcanal@igalia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 7c41cdcd3b ("OPP: Simplify the over-designed pstate <->
level dance"), there is no longer any need for genpd providers to assign
the ->opp_to_performance_state(), hence let's drop it.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231012153607.101465-1-ulf.hansson@linaro.org
Since commit 7c41cdcd3b ("OPP: Simplify the over-designed pstate <->
level dance"), there is no longer any need for genpd providers to assign
the ->opp_to_performance_state(), hence let's drop it.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231012153558.101445-1-ulf.hansson@linaro.org
Since commit 7c41cdcd3b ("OPP: Simplify the over-designed pstate <->
level dance"), there is no longer any need for genpd providers to assign
the ->opp_to_performance_state(), hence let's drop it.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231012153550.101425-1-ulf.hansson@linaro.org
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006224614.444488-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the pmdomain fixes for v6.6-rc[n] into the next branch, to allow them
to get tested together with the new pmdomain changes that are targeted for
v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for_each_node_with_property performs an of_node_get on
each iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230907095521.14053-5-Julia.Lawall@inria.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds support for MTK_SCPD_STRICT_BUS_PROTECTION capability. It is a
strict bus protection policy that requires the bus protection to be
disabled before accessing the bus.
This is required by the mt8365, for the MM power domain.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-8-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This updates the power domain to support WAY_EN operations. WAY_EN
operations on mt8365 are using a different component to check for the
acknowledgment, namely the infracfg-nao component. Also to enable a way
it the bit needs to be cleared while disabling a way needs a bit to be
set. To support these two operations two flags are added,
BUS_PROT_INVERTED and BUS_PROT_STA_COMPONENT_INFRA_NAO. Additionally
another regmap is created if the INFRA_NAO capability is set.
This operation is required by the mt8365 for the MM power domain.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-7-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use flags to distinguish between infracfg and smi subsystem for a bus
protection configuration. It simplifies enabling/disabling and prepares
the driver for the use of another regmap for mt8365.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-6-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Separate the register access used for bus protection enable/disable into
their own functions. These will be used later for WAY_EN support.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-5-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bus_prot_mask is used for all operations, set clear and acknowledge. In
preparation of m8365 power domain support split this one mask into two,
one mask for set and clear, another one for acknowledge.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-4-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To simplify the macros, use a flags field for simple bools. This is in
preparation for more flags.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-3-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow a consumer driver to use the OPP library to scale the performance
for its device, let's dynamically add the OPP table when the device gets
attached to its SCMI performance domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230925131715.138411-10-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Per "dt-bindings/firmware/imx/rsrc.h", `IMX_SC_R_DMA_2_CH0 + 5` not
equals to IMX_SC_R_DMA_2_CH5, so there should be two entries in
imx8qxp_scu_pd_ranges, otherwise the imx_scu_add_pm_domain may filter
out wrong power domains.
Fixes: 927b7d15dc ("genpd: imx: scu-pd: enlarge PD range")
Reported-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20231001123853.200773-1-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
